OCing 2500+ K7N2 Delta-L (which bios to use)

i wanna OC my cpu 2500+ to 3200+, my bios is the default i think, cuz i never changed it.
my system
amd 2500+ XP barton
k7n2 delta-L
2x256Mb ddr400 twinmos
20Gb 5400rom maxtor
40Gb 7200rpm Maxtor
160Gb 7200rpm Samsung
370W
Gigabyte 9600Pro 128Mb
52x24x52 cdrw
120mm fan, 2x80mm fan, stock cooler for my cpu
hmm so jo think my PSu can still handle OCing? i got 50+ ultra bright red LEDs running too (@ 2.3Volts each)

well the cpu temp stay in 40-55 degrees celcius and case temp 20-35C
i run 3dmark03 with no hangs and stuff
however on Aquamark3 i only get a score of 21826
DATE: 2004-12-11 04:18:11 Set this Measurement to be public. Delete this measurement
CPU: AMD Athlon(tm) XP 3200+ CR: 2186 MHz SRAM: 512 MB OS: Microsoft Windows XP
GFX: GIGABYTE RADEON 9600 PRO CM: 398 / 297 MHz VRAM: 115 MB DRIVER: 6.14.10.6467
# 1 AquaMark Score: 21826 (CPU: 4611, GFX: 2868) FPS: 21.83 TPS: 6570 K Compare
RES: 1024x768 x 32bit AA: Off AF: 4x DETAILS: Very High View
DATE: 2004-11-29 11:32:32 Set this Measurement to be private. Delete this measurement
CPU: AMD Athlon(tm) XP 2500+ CR: 1819 MHz SRAM: 512 MB OS: Microsoft Windows XP
GFX: GIGABYTE RADEON 9600 PRO CM: 398 / 297 MHz VRAM: 125 MB DRIVER: 6.14.10.6467
# 1 AquaMark Score: 25538 (CPU: 5803, GFX: 3297) FPS: 25.54 TPS: 7687 K Compare
RES: 1024x768 x 32bit AA: Off AF: 4x DETAILS: Very High View
not really sure why, im thinking of Service Pack 2, ever since i installed SP2 my computer had been running slower than before (installed it 2 days ago cuz i repaired my sindows xp and downloading sp1 would make me go over my monthly bandwdth limit)

Similar Messages

MSI K7N2 Delta ILSR - RAID BIOS Option ???

hi ho,
i have my 2 storage devices pluged into the promise 376 onboard controller. they are not connected as a real raid (not mirror nor real stripe). my OS is win2k on the first sata device and everything was fine for a long time.
but now when my system boots, it detects the ide drives and then i see the irq board.
right after that the system stops and tells me 'disk boot failure'. so i don`t get the chance to configure my raidcontroller or my sata devices.
it is as the controller is deactivated. i remember a bios version where you could activate and deactivate the sata controller. but in my bios (right now it is v7.8) there is no such option.
i have tested so far:
- reset cmos
- flash bios v7.5 to 7.8
- disconnected sata drives
anyone with similar problems or any suggestion?
> MoBo : K7N2 Delta-ILSR Bios v7.8
> CPU : AMD Barton 2500+ (not overclocked)
> Ram : TwinMos 1GB 3200 400Mhz
> Sata : 2 x Maxtor 120GB Sata (as single Devices on Raid-Controller)
> Ide : 60GB IBM DeckStar
> Gra : ATI 9600 pro 128MB
> Aud : SB Audigy 2 ZS
> Pow : SilverPower 350W, +3,3V/+5V@25A and 12V@18A
> OS : win 2000 SP4 + Security Updates 31.07.04 + DirectX 9.0c

watch the bottom of the screen after pressing Enter on the "Welcome to Setup" screen. There will be some moments of files being loaded, and then you should see a message appear which says "Press F6 if you need to install a 3rd party SCSI or RAID driver". This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear. After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the sata controller.
specify a device press S, select "win 2000 promise fasttrak 376 controller" it will read floppy and load, dot not remove floppy yet, continue win2000 install it may nead to access floppy to finish installing raid driver, did you do it like this.
try making some floppy boot disks and boot to floppy instead of cd.
http://freepctech.com/pc/002/files010.shtml
when you say there not listed, where did you see this? they wont be listed, windows will search for fasttrak controller so it will see sata's conected to it with out you knowing, so long as you load the controller from floppy that came with mobo as above.

Basic Question on Copy and Delta link which one to use when?

Hi
Its basic question
My understanding about copy and Delta link is
Copy doesnot ahve direct relationship with source object (but it acts as a sibling) any changes done to spurce object does not affect target object.
Where as Delta link will have a parent child relation ship between source object bacially its a copy of source and inherits id properties. in case if i change source object does this affect target object, we can delete, add content to delta link target object.
let's say if i want to use standard quickpoll iView do i need to use copy or delta link similarly for other iviews, worksets, roles which one will be better.
Regards,
Murali

Murali,
Yes, your understanding is right.
Case 1 : Copy
A- Object
B- Copy of A
Both of them are independent.Any changes in A are not dependent on B and vice versa.
Case 2 : Delta Link
A - Object
B - Copy of A (via Delta link)
Any changes to A are reflected in B, as A is a parent and B a child.
But B would be an independent entity.Any changes to B would not effect A.
When you use either of them, depends on your need. When you are working with standard iviews or roles or workset, you can do a copy of the original, because in most cases we would not make changes to the standard roles or worksets or iviews. There by eliminating the process of making a delta copy.
But, if you are dealing with the roles that you have created and want to make a copy of it, you can use a delta link, because, even if you want to add more iviews and worksets to that role, they would get reflected when you make a delta copy.
Hope that helps.
Consider rewarding points for handy posts!
Cheers,
Sandeep Tudumu
Edited by: Sandeep Tudumu on May 6, 2008 2:10 AM

New Modded BIOS for K7N2 Delta ILSR

MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
download here:

Description: Access through interface which is on insecure interfaces list detected. Request aborted.
Interface/Client IP address:
Date: Wed, 18 May 2005 13:11:17 GMT
Doesn't work for me
By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
EDIT: Thanks it's working now

Boot problems with IDE HD and SATA HD on K7N2-Delta L

I'll get right to the point.
I have an PCI SATA Controller Card in my system (using a K7N2 Delta-L motherboard, BIOS v5.7 with an Athlon XP 2800+ and Corsair ValueSelect 512MB DDR400 RAM on a single stick). My system works fine in it's original configuration of drives (CD-RW drive only drive on IDE bus, and SATA drive only hard drive). However, upon installing my IDE hard drive from my old computer, the system will no longer boot right. I am connecting the other IDE HD as Slave on the CD-RW's bus, as I'm reserving the second bus for bigger and better things such as a DVD burner, and speed isn't too important for this hard drive as it's just my MP3/data I don't need in a hurry drive.
In the current configuration, all three drives are detected properly (CD-RW and HD detected on the IDE detection screen, and the SATA drive detected on the SATA card's detection screen). However, after the SATA detection screen, the system just stops. The cursor is still blinking, but nothing comes up.
Both hard drives are Western Digitals (IDE is a ATA100 Western Digital 60GB at 5400 RPM, and the SATA is a Western Digital 36.7GB at 10,000 RPM), and the CD-RW is a HP CD-Writer 9100. I have Windows XP installed on both hard drives (first partition of the IDE, which is divided into two), but considering the system doesn't even attempt to boot I don't think that's an issue. I've gone through and tried enabling and disabling "Boot Other Device", but still no love. My boot order is set to Floppy, CD-ROM, and SCSI, which works fine when the SATA drive is in there.
Any idea what's up? I can provide more information upon request, as I'm sure there's something I forgot to mention that's important.
Thanks.

Take a look at this link, https://forum-en.msi.com/index.php?threadid=71384, I think you both have the same problem. It seems that a sata drive doesn't like having an ide drive in the system that has an active partition.
Do like Wonkanoby suggest, reformat the ide hard drive and make sure that it's not set to be the active partition in the system. Boot with a 98 boot floppy if you have to so you can format the ide drive to fat32, once you can boot up using the sata drive you can use xp disk manager to convert the ide drive to ntfs.

K7N2 Delta & keyboard issues?

Just put together a nice new system, I love the nforce2 board but i'm having issues with my keyboard. Its a logitech elete duo wireless but the same thing happens with standard ps/2 keyboards. In several of my games, I am unable to bind the arrow keys. Also, functions prebound to the arrow keys misfunction. i.e. when I try to walk in CS/halflife/Urban Terror it also triggers primary fire. Other games like standard Quake 3 and Vice city work fine...so I'm out of ideas. I have the newest chipset, video, and keyboard drivers.
Thanks in advance for any help,
Mike
XP 2500+
K7N2 Delta
512mb Kingston DDR3200
ATI 9800 Pro AIW

Have you updated your BIOS to the most current version?
I tried my Logitech wireless on my ASUS board and my K7N2G-ILSR and it wouldn't work properly on either one...it's something with the nf2 chipset I'm thinking but I haven't researched it in depth because I have 4 systems and parts to build more so I use a Logitech MX700 mouse and my original MS Natural Black Keyboard PS/2...winning combo and why fix something that isn't broke?
Bonz 8)

K7N2 Delta - L & memory config

I searched the forum for this and didn't find the answer. Since it's a generic question I'm hoping I don't have to list all the specs.
K7N2 Delta L w/ BIOS 6570v56 installed
Currently running 2 sticks Crucial 3200 400 DDR 256mb cas 2.5 dimm slot 1 and slot 3 - dual channel
Just purchased a new stick of Crucial 3200 400 DDR 512mb cas 2.5
Where should this stick be installed for best performance?
Will I lose dual channel if all 3 slots are used?
If I lose dual channel, which set up is better:
Dual channel w 512mb total ram
OR
No dual channel w/ 1gb total ram
Thanks

Quote
Originally posted by gleonard
I was wondering about the dual channel w/ all three slots. I already have 2x512 in slots 1 & 3. I was hoping I could add another 512 stick and still have dual channel. But it looks like according to previous posts that it won't because all my sticks would be equal in size. Guess I'll have to be satisfied with just 1Gb ram for now.
from what i heard you can have 3 stick all of the same size and use dual channel.
but 512mb would run in single channel but have not got a confirmation it really works,.
and what do you need so much memory for ?

[nForce] K7N2 Delta Premium stuck at Chipset Initialisation

Hi there, I'm new to these boards, how do you all do?
As stated in the subject I'm having trouble with a new K7N2 Delta Premium which is stuck at Chipset Initialisation. I'm not going to write out a long explenation here as I have been battling with this for a week and I have a thread in another forum where lots has already been discussed. Hopefully it will save time in people suggesting stuff that's already been tried etc. Here's the link.
Thanks in Advance,
Matt

Sorry Richard but it had been a long day and I just wanted to get a quick post in before going to bed and hopefully some answers by morning.
I'll hold back on the sig for the moment if you don't mind as I haven't yet got a working PC with an MSI board and am using components swapped, borrowed and thieved from other PCs so to list it all probably wouldn't fit
Here's a list of everything I've used so far.
AMD Athlon XP-M 2200+
AMD Athlon 800
ASRock K7-Upgrade
MSI K7N2-Delta Premium
2*256MB PC2700 (Generic)
2*512MB PC2700 Kingston Value RAM (Sourced from an ASUS A7N8X-E Deluxe based PC with an AMD Sempron 2800+)
GeForce4 Ti4200 64MB
Radeon 9600Pro 256MB (Sourced from an ASUS A7N8X-E Deluxe based PC with an AMD Sempron 2800+)
120GB IDE HDD
Lite-On 16x DVD-ROM
Lite-On 32x CD-RW
Asus TV FM Card
300W PSU (Spare) (3.3V = 15A, 5V = 35A, 12V = 11A)
350W PSU (Original)
350W TaurusX PSU (3.3v = 20A, 5V = 33A, 12V = 18A) (Sourced from an ASUS A7N8X-E Deluxe based PC with an AMD Sempron 2800+)
Any combination of all the above components produces the same result, all items power up and the motherboard stays in Chipset Initialisation mode. All components have been tested and are known to work in other PCs (namely the ASUS A7N8X-E Deluxe based one) except the 2 motherboards and CPUs.
Now for a slightly condensed version of all my posts from the other Forum:
Quote
On monday I turned the PC (configured using the ASRock mobo, Athlon XP-M, Ti4200, Generic RAM and 350W PSU) and it booted to the welcome screen fine except I had no response from my keyboard and mouse. Being wireless models I scanned for a different channel but no luck so I tried the reset switch on my case. The computer began to boot and nothing happened. The monitor wouldn't come on and the PC just sat there with the HD light stuck on.
I left it and took the PC to work the next day (I work in an IT department so could 'borrow' a few spares to try out). At work I swaped out the graphics card (it's hadn't been initialising properly when I used drivers other than those that came with windows, stuck at 4 colours at 640*480) for an FX 5200, no change. I swapped the graphics cards back and took out a stick of RAM, no change. I swapped the two RAM sticks around and the PC booted, great, I thought, faulty memory, at least it works I'll buy a replacement the weekend.
Took the PC home and turned it on again, same problem as before. I tried swapping both sticks of RAM in and out as well as re-seating the graphics card, no change. I tried the RAM and graphics card in another PC and it booted fine so I thought, dead mobo.
Today I go to the local computer fair and buythe MSI mobo. I reinstall everything and turn the PC on, same as before, only the diagnostic LEDs tell me the board is stuck in 'chipset initialisation mode'. I try chopping and changing the RAM again and try the Radeon from one of my other PCs, no change. Wonderful, I now have the feeling that my lovely 2 week old XP-M 2200+ that I hadn't had a chance to play with yet has broken so I swap it out for the Athlon 800. Hallelujah the PC boots first time and I go straight into the BIOS. I check all the settings and enable/disable the onboard peripherals I do/don't want/need. Restart the PC and it's back into Chipset Initialisation mode again. Doh! So I know think I messed up on the BIOS settings somewhere so I reset it, no change. I reset it again (this time removing the battery from the board as well as unplugging the mains and setting the jumper), no change. I try swapping out the RAM and graphics card again, still no luck.
Quote
All my testing is performed on the desk for my second PC which uses a standard MS wired desktop.
I've tried pairing the PC down to just CPU, RAM, graphics card. When the PC was first tried with the XP-M 2200+ and the MSI board I even tried it with just a Graphics card and with just RAM, same result.
All components apart from the CPUs and TV Tuner have been swapped out with components in another PC and that PC booted with each one of them in and is still booting now.
Tommorrow I'll try the TaurusX PSU and try the board layed out on the table and see how it goes.
Quote
I've tried swapping the power supply and it still wouldn't boot. On a whim I removed a memory stick, yes it booted. I left the pc for a while sat in the BIOS and all was good. I took the risk and swapped the CPU for the better XP-M 2200+. This booted first time too, infact it booted with both memory sticks in. Great, it was a dodgy power supply, except that power supply is now in the ASUS A7N8X-E Deluxe PC I was robbing parts from and working fine.
After leaving the PC sat in the BIOS HW monitor for a while watching CPU temps I decided to restart and get on with installing windows. Doh! back to chipset initialisation mode again
Next step..... try it out of the case on my dining room table.
Quote
I've now tried the MSI motherboard on my desk (wooden) with just the XP-M 2200+, Ti4200, Kingston Memory, hard drive and Diagnostic LED bracket connected. It results in the same problem (and this is with yet another power supply to the previous two being used, the 300W one) as well as the TaurusX PSU, the PC sits at Chipset initialisation stage.
Some more info for you. Whilst researching a problem on a PC at work (uses a K7N2 board), I found people stating that the nForce2 chipset has problems with certain types of memory (news to me, I've got two other nForce2 based PCs both A7N8X-E Deluxes). So I decided to try yet again to boot one of my other PCs with this memory, both dimms managed so fine. I also decided to run a proper overnight memtest on the dimms indivdually, the first one went almost 8 hours and 56 tests with no errors, the second one had done one test by the time I left for work this morning, again no problems.
I'm scraping the bottom of the barrel here and am simply running out of ideas. All that I can think to do now is try both the XP-M 2200+ and Athlon 800 CPUs in one of my working nForce2 PCs (which I am reluctant to do cos I'm idle).
Quote
OK, another update. Got home about quarter to 2 and the second 256MB DIMM had gone through 50 tests without errors so the memory is fine (and is fine with nForce2 mobos as that's what I tested in).
I've used two different keyboard and mouse sets, the wired one on my second PC and the wireless one (which also works conected up to my second PC). No difference, the system is barely getting far enough to even think about keyboard and mouse. Hell it's not even getting far enough to complain about missing memory or graphics card.
I still don't have any real idea as to why the first motherboard 'failed' like it did anyway and the only two components that I can't completely rule out are the CPUs and motherboards. I do have an Athlon XP 2800+ with what appears to be a cracked core (though oddly enough the PC always booted with it installed, it was just highly unstable with lots of memory errors) that I could try if I really felt like it.
I haven't tried the 'cracked' XP 2800+ yet and I'm about to try the ASRock motherboard with the Athlon 800 again. As I've said in the quotes above, I'm completely dry when it comes to ideas now and am hoping an MSI specific forum might be able to help me more.

K7N2 Delta ISLR lock-up sound

Help!
I just got a K7N2 Delta ISLR and installed it in my system. Over the course of a few painful days I've realized that system has a propensity to lock up after I load the sound drivers for the motherboard. If I don't do that the system is completely stable but of course I don't get sound. I get this problem even when I'm only using one hard drive with nothing else in the system.
I've followed liquidsoul's NForce 2 Installation How To guide on www.AMDMB.com's forum but to no avail. Has anyone encountered this problem or know how to fix it?
Thanks!
My system specs are:
K7N2 Delta ISLR (newest bios)
1400 Athlon
2*128 DDR 266 (generic)
Plextor 12X burner
Pioneer 10X DVD-Rom
80Gb WD HDD 8Mb
40Gb Maxtor HDD
40Gb Maxtor HDD
Promise Ultra 100
Windows XP Pro SP1
Logitech Cordless Optical (keyboard & mouse)

Thanks Deathstalker & scooter787b!
When I set up the PC originally I only had one hdd in it and I did not install the promise card (you have to install them later because I've found I need to flash the bios of the promise cards so that it will be recognized by windows XP) so I guess I did do the KISS principle (I've learnt my lesson the hard way before).
That said I did the installation thing and everything looked fine. However, the lock-ups occur at no particular interval so after 3 hours and nothing wrong I installed most of the other hardware booted it up and it seemed good. But a day later the lock-ups started happening. Even removing the extra hdd and promise (btw I did put the promise card in PCI 3) card did not help (I went all the way back down to one hdd and still got the problems). I went through many reinstallations of Windows XP SP1 as well.
During the process of elimination I even bought a nice OCZ Dual DDR EL Kit but that didn't help. Also, I changed from my 350W enermax to a new 450W enermax. Problem did not stop happening. I know the hard drive I was using is in good condition.
In terms of drivers I tried the ones that came with it, 2.03, 2.45 and the realtek ones.
After 7 days of painful elimination I'm leaning towards the problem being the board.

Need help with jumper settings for k7n2 delta ilsr

I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
Thanks, Ron.

Hi,
As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
Axel

New bioses for K7N2, Delta & K7N2G released-Updated

MSI has posted new bioses for the K7N2, Delta and K7N2G series mainly adding Sempron support for these boards as follows:-
K7N2G-ILSR bios version 2.0
K7N2 Delta-ILSR & L bios versions 7.8 & 5.8
K7N2 & K7N2G-L bios version 4.1
K7N2GM-L bios version 1.6
MS-6729 bios version 5.4

Quote
Originally posted by Raven
a athlon xp is rated up to 85 celsis and if its from April 2004 it should be quite correct.
carefully touch the heatsink to check if its warm or not
also what is your other temps ?
what program do you use to check temp ?
pc alert4 is known to show wrong from time to time.
i use speedfan and it works god form e.
http://www.almico.com
but the higher the temp the sooner it will fail.
55-60 is what most people recommend as maximum temp under load.
I know its rated up to 85C but won't it start being unstable around 75C?
I use SpeedFan, MBM5 to check temps. Not sure about the case temp but the socket temp is like 28-35C I believe.

OS install woes on K7N2 Delta 2 platinum

Good day everyone,
this is my ERROR MESSAGE:
The page is caused by the following file: ACPI.SYS
Page fault in non page area
Technical Info
**** STOP: 0X00000050, (OXB8FC15FF, 0X00000000, 0XF999056E, 0X00000000)
**** ACPI.SYS - ADDRESS F999056E BASE AT F9972000 DATE STAMP 3b7d8550
Sometimes i get DISK BOOT ERROR
System Specs:
MSI K7N2 DELTA 2 PLATINUM
BIOS WNMS6570 11.4 08-16-04
AMD XP 3000
MSI FX5700 LE 256MB
52X CD ROM
FLOPPY
I have tried the following HDD:
1) HITACHI 60 GIGI ATA
2) MAXTOR DIAMOND PLUS 9 80 GIG SATA
3) MAXTOR 200 GIG ATA
Can any advice please, thank you.

Advanced Configuration and Power Interface
need a driverXP or PSU ain't up to par
try Nforce unified 5.10 driver

Problems with K7N2 Delta @ FSB200Mhz

Hi,
SORRY FOR MY POOR ENGLISCH
I've got a problem with my K7N2 Delta -L Board.
I use a Athlon XP Palo 1700+. Standart for this proz is FSB 133 and multi 11.
Now i tried to use FSB 200 an multi 7,5. =>1500Mhz.
I works fine an never crashs.
BUT if i turn off the pc for more than 15mins it doesn't reboot anymore. Only a safereboot@100mhz is possible.
The setting have to be in the BIOS advanced chipset AUTO an FSB 200 than it boots and restarts without problems until i turn it off.
The setting MANUAL and FSB 200 doesn't work even if i don't change any other setting. It never boots
RAM : CPU is 1:1. RAM is 400Mhz
What's wrong?

Yes, the Proz is unlocked. It works fine. The "strange" thing is, that after a shutdown and power-off of more then 15min it hangs while rebooting.
You have to choose auto performance and FSB 200 otherwise it does't works with FSB higher than 150
Why raise the v-core? It works fiin without probs and stable only boot-probs after power-off . Reboots works fine.
The same proble occurs while using FSB 166.
What has MSI done?
Auto FSB200 works
Manual FSB 200 not
and the aren't able to reply to e-mails...
Sorry next time spend some more € for an working a*us MB

Problems with DMA (WinXP + MSI K7N2-Delta)

Hi!
I'm having problems with my IDE dvd-burner (NEC-1300) as I can't get it to use DMA in Windows XP. The motherboard is a MSI K7N2-Delta. I've tried using Nvidia's newest driverpack, 2.45, but in vain. The only mode I can use is PIO and it slows slows down the computer.
Thanks in advance!
Jussi Teppo

Quote
Originally posted by
wonkanoby
what drives make models in pc in detail
what else is on each ide
hows every thing jumpered
is it a modern 80 wire ide lead
On Primary Master I have a 60Gb Seagate Barracuda ATA IV. And the Secondary Master is the NEC-1300 http://www.necd.de/productdetail.php/id/672, which is supposed to be fully capable of UDMA-2 (33) as all the modern drives are (some are even UDMA66). The drive are jumpered as Masters. The wires are ok (UDMA100).
Registry editing suggested in a another message didn't work, neither did deleting the ide-channel.
I found a temporary solution to this: I placed the DVD-RW as Primary Slave and it works. The drive is detected as UDMA33-capable. Why it doesn't work as Secondary Master is beyond my knowledge.
Raven_
Yes, you guessed it. I do indeed live in Finland. Hur är läget?
Thanks to everyone for the effort!
Jussi Teppo

Win XP problem w/k7n2 delta ilsr

I forgot to put this in my first post. I have a k7n2 delta ilsr and I'm using win xp pro. In device manager under Other Devices it reads:
? ethernet controller
? raid controller
? sm bus controller
? universa serial bus usb controller
Did I forget to install or setup something.
Thanks, Ron.

Hi,
Yes, you should install the nForce drivers for your board:
The latest ones are here:
http://www.nvidia.com/content/drivers/drivers.asp
Axel

OCing 2500+ K7N2 Delta-L (which bios to use)

Similar Messages

Maybe you are looking for