Officejet 4315 Photo Printing Problem

Trying to print photo. Getting fax setup page instead. Help!

make sure you're selecting the correct printer icon. there is a problem with Photo Printing Wizard and Photo Gallery in Windows Vista, where when trying to print, it does not select the default printer icon, and sometimes selects the fax icon.
so double-check the FULL name of the printer icon before printing.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

Similar Messages

  • Officejet Pro K5400 printing problems after update to Mavericks OSX 10.9

    Hi,
    I have printing problems with my Officejet Pro K5400 after update to Mavericks OSX 10.9.
    Now after printing 1 page the printer prints an extra page with '2345X' sentence on it. As this problem started right after updating, I suppose there is a problem with an update.

    This patch did solve our problem with the K5400 feeding a "blank sheet".
    Thank you.

  • Photosmart B8550 - photo printing problems

    Has anyone else had the problem of photo printing perfectly on all papers except HP Photo paper?  I loose all my black tones when I print on the photo paper, but I bought Kodak paper and it worked.

    Yes, I am having the same problem and also all of the other problems reported. One printer head has already been replaced and another is on its way. Not to mention the catridges (black) that I wasted in the process. When it prints, the quality is superb. It is just failing too often with less than six months of operation.

  • Photo printer problems

    Had a series of green and orange flashing lights on photo printer. canon advised me to buy new since repair cost would be prohibitive.  received new one   am getting same message and now, printer doesnt recognize my ink i had been using in old ip3600- same new model   changed to new canon ink supplied with printer  same ink message;  tried to load old ink support form in tank figuring might be defect in spot where large black tank goes;  same thing happend   any suggestions?

    Hello hunkress7.
    Please document the exact error pattern that is shown on the printer with the new cartridges installed.  Count how many times the light flashes orange before it flashes green, or count how many times the lights alternate before the pattern repeats.
    This didn't answer your question or issue? Find more help at Contact Us.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • Color LaserJet CM1015 mfp photo printing problem

    I am running a Color LaserJet CM1015 mfp utilizing only HP print cartridges and HP Color Laser Photo Paper, glossy, yet I cannot seem to get a decent photo to print.  There is always a black smear or two on the front of the printed page.  It prints black and white and color just fine on plain paper but I cannot get a decent print on glossy.  This has happened since day one so I don't think it's a dirty print roller,,etc. issue.
    Thanks for any ideas!
    Michael 

    Yes I solved the problem. I had to clean the registry of all information regarding this printer. During the installation I noticed interesting thing. The only installation that worked well was from the CD that came with the printer. I've tried downloaded latest version but it didn't install properly and have no idea why.
    Inkjet and Laser Printer Supplies
    Printer Cartridge Recycling
    http://www.cartridgeshop.com.au

  • Photo printing problems

    Trying to print 4x6 photos from computer using hp premium photo paper.  Using the windows photo gallery manager application on computer.  Was able to print the first three photos but printer stopped printing.  Print jobs go to the printer que but nothing ever prints.

    Hello again wingome
    I found an article for the printer you provided "Print jobs stuck in queue". It may resolve your issue.
    Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
    When a solution is found please mark the post that solves your issue.

  • Photosmart 7350 Photo Printing Problems

    When I print a photo with my Photosmart 7350, it would stop printing after 2/3 of the photo was done. I uninstalled the printer, then reinstalled, and now the whole photo will print, but where it used to stop, the quality of the print drops significantly. It's always in the same spot, no matter the print quality selected.
    I'm using Win XP, SP3 and a USB connection. I get no error messages of any kind.
    Any suggestions?
    Message Edited by mandalore84 on 03-08-2009 07:57 AM

    Yes, I am having the same problem and also all of the other problems reported. One printer head has already been replaced and another is on its way. Not to mention the catridges (black) that I wasted in the process. When it prints, the quality is superb. It is just failing too often with less than six months of operation.

  • C6280 Photo printing problems

    Any time I want to print photos on HP photo paper they come out with alot of pink and yellow - grey clouds show up as pink and light green shows as yellow.  It doesnt matter if I use the printer 'reprint photos' button or go through the print functions on the computer.  This goes for photos I already have saved on the computer, just scanned into the computer using the C6280 or just using the printer functions without the computer.
    If I print the very same photos on ordinary paper ie not photo paper, they turn out perfect.  So it is not a scanning issue.
    I have changed the printer settings to Best print, HP premium paper, and changed the RTL to what was suggested in the printers instructions - they still come out overdone with pink!
    I am an avid scrapbooker so printing my own photos is a must!  These same photos and photo paper worked well together on our previous HP (a 900cxi)
    What setting am I missing?
    This question was solved.
    View Solution.

    Hi,
    I think there are 2 possibilities here. Both are equally likely.
    1) One of the cartridges is close to empty. Maybe the Light Cyan. Printing the photos in normal plain paper mode may use different amount of ink from different cartridges so thsi coudl explain why the problem is not observed there
    2) You're using media from yoiur old 990cxi that doesn;t work so well with the newer inks in your C6280.
    C6280 uses HP Advanced or HP Everyday photopaper. http://www.shopping.hp.com/webapp/shopping/supplies_model.do?model_name=HP%20Photosmart%20C6280%20Al...
    990cxi also can use these 2 paper types but if you had stockpiled soem premium or premium plus photo paper from this printer this might not work so well on teh C6280. http://www.shopping.hp.com/webapp/shopping/supplies_model.do?model_name=Deskjet%20990cxi
    Please let me know if this helps.
    Regards,
    Although I am an HP Employee I am not expert on all products.
    The views I express here are my own and in no way represent the views, opinions or strategies of HP.
    I'm just trying to help out if I can.

  • Photo printing problem on 2230

    Business ink jet 2230 prints black & white photos with purple tinge.  Print heads have been cleaned,  Plenty of ink in cartridges

    Okay.
    I've tried something, it works.
    Nothing's perfect but I can print pretty decent quality from my Epson R800 on Snow Leopard.
    First, I uninstalled GutenPrint. Just downloaded the 5.2.4 update, then run the uninstaller.
    Reboot. Done.
    Second, I've downloaded the last Epson drivers for my R800 (epson13197.dmg - 30.9MB - posted on 24/08/09), installed it, reboot then run a Permission repair routine.
    Third thing : From the Printers and Fax Preference Panels, I've flushed the old R800 printer settings then reinstall a fresh new one. The driver use is now Epson SP R800 (1). +(GutenPrint is definitively out.)+
    From now, adjusting the setting in the printer driver, I can print decently.
    No more use of .icc profiles (when printing from Lightroom and Photoshop, pictures are dark, I mean really dark, and oversaturated).
    Final problem : unsolvable.
    Whenever I start a 64-bits application (Safari, Mail, etc.) , there's no printer's settings available. Every window allowing settings is «crossed» and the driver is telling me that «The windows are not compatible with this version of the software, please contact Epson».
    But If I use a preset sets in a 32-bits application, the preset is use properly.
    I can't change it, but it print according to the preset.
    Good luck, Snow Leopard users.
    We should see a driver's update soon from Epson ... I hope.

  • Deskjet D4260 printer - Photo Printing Problem

    I have a Deskjet D4260 printer, OS Windows 7.  When I print a 4  6 photo in landscape, the photo comes out on half the paper.  How do I correct this?
    Thanks,
    Colleen

    cookie1144,
    This article should help resolve your partial pages:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01892627&cc=us&dlc=en&lc=en
    Give the steps listed under your operating system a try and let us know if it helps.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Officejet 4500 wireless printing problem

    We have an HP Pavilion g7 laptop that has always worked great with our 4500 wireless printer.  Now the computer says the printer is offline.  The wireless button is blue.  The computer hard wired to the printer shows that it is online.  What else am I missing?  Can anyone help?!?
    This question was solved.
    View Solution.

     Hi,
    Please use the following tips/instructions to fix:
        http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02221706&cc=us&lc=en&dlc=en
    Good luck.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Officejet 6700 duplex printing problem

    Hi. When I select duplex printing on my new Officejet 6700, the image looks squashed (horizontally) so the circle looks like an upright oval. It prints fine when in single-sided mode.

    Hello again Nich7503,
    Thank you for the update and the feedback.  Contrary to popular belief, we do value this information and want our users to have the best possible experience.  I've included a section of the User's Guide below, would you mind validating the duplex process that you used to get these results?  Just in case, the link to the User's Guide is pasted below these steps.  Thanks again........
    Print on both sides (duplexing)
    You can print on both sides of a sheet of media automatically by using the automatic twosided printing accessory (duplexer).
    NOTE: Two-sided printing requires an automatic two-sided printing accessory
    (duplexer) to be installed on the printer.
    NOTE: You can perform manual duplexing by first printing only the odd pages,
    flipping the pages over, and then printing only the even pages.
    Perform two-sided printing (Windows)
    1. Load the appropriate media. For more information, see Load media.
    2. Make sure the duplexer is installed correctly.
    Chapter 2
    36 Print3. With a document open, click Print on the File menu, and then under the Print on
    Both Sides options on the Layout tab, select either Flip on Long Edge or Flip on
    Short Edge.
    4. Change any other settings, and then click OK.
    5. Print your document.
    Perform two-sided printing (Mac OS X)
    1. Load the appropriate media. For more information, see Load media.
    2. Make sure the duplexer is installed correctly.
    3. Select a paper size:
    a. From  the File menu in your software application, click Page Setup.
    NOTE: If you do not see a Page Setup menu item, go to step 4.
    b. Make sure the printer you want to use is selected in the Format For pop-up menu.
    c. Select the paper size from the Paper Size pop-up menu, and then click OK.
    4. From the File menu in your software application, click Print.
    5. Make sure the printer you want to use is selected.
    6. Select the paper size from the Paper Size pop-up menu (if available).
    NOTE: You might need to select the paper-size option labeled Two-Sided
    margins.
    7. Click the Two-Sided Printing pop-up menu, select Print Both Sides, and then click
    the appropriate binding options for the document.
    - OR -
    Click the Layout pop-up menu, and then select the appropriate binding options for
    the document from the Two-Sided pop-up menu.
    NOTE: If you do not see any options, click the disclosure triangle next to the
    Printer pop-up menu or click Show Details.
    8. Select any other print settings that you want, and then click Print to begin printing.
    Print on both sides.
    http://h10032.www1.hp.com/ctg/Manual/c03227497.pdf
    I worked for HP but my posts and replies are my own....Thank you!
    *Say thanks by clicking the *Kudos!* which is on the left*
    *Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

  • EPSON R300 PHOTO PRINTING PROBLEMS

    i have an epson r300 printer connected through my wireless router to im imac but when i try to print, all this crazy text comes out rather than what i want.. so im guessing that it is corresponding with the printer to at least some point since i recognises i want to print but thats it? any help is appreciated.

    I was having the same problem with my Epson printer. I went on the Epson website and downloaded the updated driver for Intel.

  • Dynamicaly Photo Print Problem in Adobe Form

    Hello Expert,
    I want to display Employee Photo on Performance Apprisal form Dynamicaly on Adobe Form(SFP).
    for which, i trieed two  method -
    1)-    
    DATA : lv_pernr1 TYPE tdobname.
    CONSTANTS: c_graphics TYPE tdobjectgr VALUE 'GRAPHICS',
    c_bmap TYPE tdidgr VALUE 'BMAP' ,
    c_bcol TYPE tdbtype VALUE 'BCOL'.
    DATA : ls_z_if_test_cv TYPE xstring.
      lv_pernr1 =  '11000003'.       " Employee Number
         CALL METHOD cl_ssf_xsf_utilities=>get_bds_graphic_as_bmp
           EXPORTING
              p_object        = c_graphics
              p_name         = lv_pernr1
              p_id               = c_bmap
              p_btype         = c_bcol
            RECEIVING
             p_bmp          = ls_z_if_test_cv         
            EXCEPTIONS
              not_found      = 1
              internal_error = 2
              OTHERS         = 3.
          break jp_deepaks.
          IF sy-subrc = 0.
            lv_filename = ls_z_if_test_cv.
         ENDIF.
    2)-
    Find Photo URL of Employee
    DATA : uri TYPE toauri-uri.
    DATA: lv_filename1 TYPE toauri-uri.
          CALL FUNCTION 'HRWPC_RFC_EP_READ_PHOTO_URI'
            EXPORTING
              pernr            = '11000003'
              datum            = sy-datum
              tclas            = 'A'
            IMPORTING
              uri              = uri
            EXCEPTIONS
              not_supported    = 1
              nothing_found    = 2
              no_authorization = 3
              internal_error   = 4
              OTHERS           = 5.
          IF sy-subrc <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
            WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
          ENDIF.
          lv_filename1 = uri.
          CALL FUNCTION 'HR_KR_STRING_TO_XSTRING'
           EXPORTING
              codepage_to      = '8500'
              unicode_string   =   lv_filename1
            IMPORTING
             xstring_stream   = ls_z_if_test_cv
            EXCEPTIONS
             invalid_codepage = 1
              invalid_string   = 2
            OTHERS           = 3.
         IF sy-subrc <> 0.
    MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
             WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
         ENDIF.
    But both methods are not working properly. How can i do this??
    Thanks in Advance,
    Regards,
    Shri

    Hi,
    I fetch the detail from table toahr with passing parameter
    sap_object = 'PREL', reserve = 'JPG'  and ar_object  = 'HRICOLFOTO'.
    i got the ARC_DOC_ID form table toahr. now how can i print this emp photo on Adobe form.
    is this hexadecimal value or string ?
    please explain the whole process for printing employee photograph on Adobe Form?
    Thanks,
    Shree

  • 8500 w/Vista Windows Photo Printing Problem

    My 8500 printer goes to Fax screen every time I try to print a photo from my Windows photo gallery. I have had the printer for about six weeks and it just started doing this. Also, I cannot get the scan feature to work.  Please, can anyone help? I live in a very rural area of Hawaii with very little support available.  Thanks,  and Aloha

    You're probably choosing the Managed by Printer "Profile:" in the Print - Print Job sidebar. There are very few printers that work with this Profile due to the internal colorspace of LR. You'll need to add and choose a Printer/Paper profile from this list and turn off color management in the Print Driver.
    Another necessary item for display / printer matching are: display calibration

Maybe you are looking for