Officejet 7000 network not recognized. Lights blink at printer connection and then go out

I plug in the network cable and the lights blink and then go out. The connection to the router is not established

Ok,
First, unplug both the printer and the router power for 30 seconds and check for any change,
if the same persists, try plugging the ethernet cable from your printer to your PC and check if the same behavior occours.
If so, than it seems like the printer eternet card is damaged, which will require service
If it is connecting with your PC, so the issue may be related with your router,
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Similar Messages

  • When I plug my shuffle in, it blinks yellow several times and then goes out. It wont charge

    When I plug my shuffle in, it will blink yellow several times and then go out. It wont charge. I do not see this as a "warning" light in the PDF handbook. Any suggestions?

    Hi aaliyafrommarkham,
    In order to troubleshoot this, I would recommend that you start with an SMC reset. Information on this procedure can be found here:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/HT3964
    Thanks for coming to the Apple Support Communities!
    Cheers,
    Braden

  • Officejet pro 8000 not recognizing brand new HP black ink cartridge

    Hi. My officejet pro 8000 is not recognizing a brand new HP brand black ink cartridge. The black ink indicator remains lit and it will not print. I have unplugged the printer, but this did nothing. It is wierd, when I open the door where the cartridges are, the light goes out, it only goes on again when I close that door. The printer was working perfectly until this . Any helpful hints? Thanks so much.

    Hello chx2,
    Welcome to the HP Forums!
    I understand your Officejet 8600 is not recognizing your brand new black ink cartridge. I will do my best to assist you! Please make sure this printer is plugged into a direct wall. I just want to see if this makes a difference.
    Next, please follow these steps in order:
    1) Remove all ink cartridges from the printer, then close the door
    2) Remove the power cord from the printer (Do not press the power button)
    3) Please clean the ink cartridges by following this HP document here. (Also, make sure you have completed all the steps from this document)
    4) Wait 60 seconds or more, then plug the power cord back in
    5) Wait for the printer to turn on completely, then install the ink cartridges
    6) Try to print a document
    Please post your results, as I will be looking forward to hearing from you.
    I worked on behalf of HP.

  • Officejet 7000 will not feed paper

    My Officejet 7000 will not take the paper from the paper supply tray.
    When I send a document to the printer it sounds normal as if the rollers are turning but after a few seconds it stops and the button with the paper icon flashes as if there is no paper (there is paper and I've reloaded and tried reprinting several times).
    Just prior to the issue, the printer was in the process of printing a multi-page document. About half way through printing one of the pages I heard a 'clack' type sound. The next page nor any subsequent attempt would feed into the printer.
    Any idea what is wrong and if it is worth fixing?
    Thank you.

    Hi there,
    This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • '"Connection Failed" : The server "rrnas01" may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again' message

    '"Connection Failed" : The server "rrnas01" may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again' message keeps displaying whenever I try to open any Adobe CS5 applications (except for Adobe Acrobat Pro). It displays until I click "OK" about 15-20 times or so and then will finally let my program open.
    I have tried deleting files within my Library/Preferences folder and turning off/deleting login items within my system preferences as other forums suggested but nothing happened. Spending 3.5 hours on the phone with Adobe and completely uninstalling and then reinstalling the entire CS5 Master Collection didn't work either.
    Also, it may be helpful to know that my programs worked fine for about three weeks then when we got internet and changed the password (the join, not the adminstrative password) with the wireless network "ScubaSteve" (which I've used with no problems at my old apartment) it started acting up. I have never seen "rrnas01" before so I don't know at all where it came from. I also installed the free 30 day trial of Suitcase Fusion 3 recently, but thinking that could also be the cause I have uninstalled it, and still no help.
    Please help me! And please keep in mind I don't know all the computer lingo that a lot of the people in these forums seem to know. Thanks in advance for ny help you can give me.

    It may not be possible .. there is a major bug between Mountain Lion and the TC where the TC disk goes off the radar of the computer.
    Lion is also affected but not as badly.
    7.6.4 seems worse than earlier firmware.. so back to 7.6.1 or 7.5.2 if that is possible.
    Obviously that is not a solution for a later Gen5 TC.
    Reset to factory after the firmware downgrade. .use all network names that are short, no spaces and pure alphanumeric.
    If the TC is the main router set the dhcp to a very short lease time.. eg 30min.. and see how it goes, or try a longer lease like 99days.
    I prefer the very short lease but response has been mixed.
    Use ethernet not wireless.. ethernet is always more reliable and stable than wireless.
    And last .. a nightly electric timer that powers off every night at midnight for 1min.. would not be the first device we have suggested a fix that amounts to beat the unit to the punch by forcing it to reboot since it is unstable.

  • My iphone 4 is not recognized by itunes when i connect to it, wants me to restore to factory settings. after i agree , an alert with error 9 stopped the sync. the phone wont start

    my iphone 4 is not recognized by itunes when i connect to it and tells me that the phone is in recovery mode, wants me to restore to factory settings. after i agree , an alert with error 9 stopped the sync. the phone wont start

    Thanks for the response. There is no cloud icon next to them. All of the songs play on the phone still and no song was purchased through iTunes. I added them manually and tried to remove them manually. According to my iTunes they've been removed but they are still on my phone and working.

  • My ipad will no longer connect to the laptop. it comes up with usb not recognized. also when trying to connect to the power the first time i connect, nothing, but when i unplug from ipad and plug in a second time it charges

    my ipad will no longer connect to the laptop. it comes up with usb not recognized. also when trying to connect to the power the first time i connect, nothing, but when i unplug from ipad and plug in a second time it charges

    yeah tried all that. the only thing that i havent tried is to delete itunes completely and restart. its the same with the ipad. i havent done a master reset. i just think it has to be something rather simple as it acknowledges that i have plugged in the ipad as it makes the noise it just come up usb not recognized. it shows up as an unknown device that doestn have  any drivers
    its driving me round the bend at the minute

  • My iPhone 3gs is not recognized by my PC or iTunes and i can't open it. Any idea what's the problem?

    My iPhone 3gs is not recognized by my PC or iTunes and i can't open it. Any idea what's the problem?

    I had the same problem with my phone, its a 3gs, out of no where my laptop stop recognizing it and wouldnt charge either, i got worried because i had all my pix and videos on my phone and didn't have a copy, so i started searching on the internet for an answer to my issue, bought extra usb cables, used different laptops and nothing worked .. Untill i took my cell phone apart and thought about replacing the (charge port assembly for apple Iphone 3gs) so ordered the part online and 3 days later got it and i just replaced it right now... and guess what/??? IT WORKED!!! YEAP.. NOW MY CELL IS CHARGING AND I JUST SYNC MY STUFF.. I HOPE THIS CAN SOLVE YOUR PROBLEM... AND ONLY COST ME 8 DLLS

  • My iphone 4 is not recognized by itunes when i connect it, wants me to restore to factory settings

    my iphone 4 is not recognized by itunes when i connect to it, wants me to restore to factory settings. do i have to or is there a better way to fix it?

    Howdy AndieKanaras,
    It sounds like your iPhone is being recognized everywhere but in iTunes. I would use the troubleshooting for that issue in the following article, named:
    If you don't see your connected device in iTunes for Mac
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • Your address was not recognized. Please check your entry and try again.

    I'm trying to register for the free 30 day trial.
    I get
    "Your address was not recognized. Please check your entry and try again."
    My address works fine for the postman, deliveries etc. Another case of a programmer who knows better!
    What are the address requirements on the sign-up form, so I can proceed?
    Pete

    Hi
    Which product do you want to register for? Office 365, SharePoint or Office 2013?
    Since this forum is to discuss problems of Office development such as VBA, VSTO, Apps for Office, and your question is related to the free trial registering of Microsoft products, I suggest you posting it in Answers
    Forum for more efficient responses.
    Thanks.
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • I have been having trouble connecting to my wifi on my ipad mini but my iPod is just fine......it will connect and then say "Unable to connect to network" I've tried resetting my ipad mini and turning off my router for 30 seconds and its not working.

    I have been having trouble connecting to my wifi on my ipad mini but my iPod is just fine......it will connect and then say "Unable to connect to network" I've tried resetting my ipad mini and turning off my router for 30 seconds and its not working.

    What TC do you have? Model number direct from the base is a big help, it will be A1 followed by 3 numbers.. eg
    A1409 Gen 4.. The new AC is A1470
    How is it setup?
    I need the whole network setup. what modem/router, how is the TC connected etc??
    I also need to know what IP the ipod gets, so I can see what mode the TC or network router is working in.

  • Hi, I'm trying to set up my Time Machine, but I get this message: The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again. how to resolve?

    Hi, I'm trying to set up my Time Machine, but I get this message: The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again. how to resolve?

    Did you reboot the TC? That is always the first step.
    Reboot the whole network if that is not enough.
    If you still have issues.. come back to us but generally the best way is to factory reset the TC and start over.
    We need a bit more info on the whole network layout and what OS you are running. What model TC you have??

  • My iPhone 4S locked to Tmobile so I contacted to Tmobile and submitted unlocking form, but I got a replied said my IMEI number was not recognized. So I tried second and third time submitted the form and got same reply.

    My iPhone 4S locked to Tmobile so I contacted to Tmobile and submitted unlocking form, but I got a replied said my IMEI number was not recognized. So I tried second and third time submitted the form and got same reply.  I've been using same handset they issued to and never changed. But I have know idea why they said they don't recognised my IMEI number. Can anyone help me to solve this issue. Thanks

    You need to call T-Mobile or visit a T-Mobile retail store.

  • Everytime i plug my iphone into my computer it says device not recognized i was syncing my phone and it got interupted and has not worked since i have iphone 4 with 4.1 software lol what can i do to not lose everything

    Everytime i plug my iphone into my computer it says device not recognized i was syncing my phone and it got interupted and has not worked since i have iphone 4 with 4.1 software lol what can i do to not lose everything

    I'd start with the following document with that one:
    iPhone, iPad, iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows

  • NETWORK ERROR.  PLEASE CHECK YOUR INTERNET CONNECTION AND TRY AGAIN

    I've been getting this message when I try and play some
    games...Flash 9.0.115 is required to view this content. Your
    current version is 9.0.47. Please download the latest Flash Player.
    But every time and try and download it I get this error
    message NETWORK ERROR. PLEASE CHECK YOUR INTERNET CONNECTION AND
    TRY AGAIN.
    I've tried changing settings but nothings working, can anyone
    please help me

    I SOLVED IT!!!!! LATEST FLASH IS INSTALLED!!!!
    Here's what I did:
    Read the information in the service note about the ridiculously sensitive download manager (DM)
    ID:
    kb400530
    It gives instructions about internet settings necessary for the DM to work on multiple browsers. I use IE 7. Some were really non-obvious, like windows need to have no constraints on size, position.  Most have to do with security, Active X settings.
    However even after I followed the directions, I got the same error message.
    But I'd gotten the general idea of what the DM needed, and went back to my Internet Options, and made a couple of additional changes. I'm not sure which of these was responsible for the success, but I'm resetting them afterward anyway.
    For all the settings in which they allowed Prompt or Enable, I chose ENABLE.
    I set Enable (vs. Prompt) for Download signed Active X controls (not secure)  - this prompts a security risk bar, which didn't interfere
    I also:
    Set ENABLE for Run components not signed with Authenticode
    Set ENABLE for Allow previously unused ActiveX controls to run without prompt
    Set DISABLE for Automatic prompting for ActiveX controls
    Set DISABLE for Automatice Prompting of ActiveX controls
    Set  DISABLE for Use Pop-Up Blocker
    Set ENABLE for everything in under Scripting section
    Anyway, you get the idea.  I was trying to give the poor software every break I could, and it downloaded with no problem.
    And then, the acid test.....I tried the site that had crashed because of lack of Flash 10 - and it tna perfectly....
    Take that ADOBE!!!!
    I hope something equivalent works for you.

Maybe you are looking for