Officejet Pro K850dn: It mentions attaching "rear manual feed slot". Where can I get this?

Manual mentions to feed heavy stock paper from behind, remove the duplex unit and replace with rear-access panel.  Where do I get a rear-access panel?  I do not recall getting one with the printer.

Thanks for this. I found the same.  I also found that you have to give the paper/card a slight push to get the printer to recognise and feed it at step 3.  Maybe the rear feed is faulty or needs a clean.
It took ages to get it to work and I must say that whilst this printer is great when it works, getting it to work reliably is another matter.  I have it attached as a network device and it often just stops working.  I believe HP release updates for this from time to time so it must be a recognised problem.
I have also just replaced a print head (black/yellow) and the new replacement was faulty, so I don't seem to have much luck.  I had a CP1700 before this one and that was also unreliable.  I had had hoped that the 8600 would be reliable, but this puts me off buying another HP unit for the office.
Perhaps someone from HP will kindly reply and advise if there are any suitable maitneance steps or checks that I can make.  That would help to restore confidence.

Similar Messages

  • I have MacBook 2.1 Intel Core 2 Duo OS 10.6.8 want to install HP Officejet Pro 6835 which requires OS 10.7 higher. How can I do this? Possible? Or Is it possible to install 10.7 upper to my Macbook 2.1?

    I have MacBook 2.1 Intel Core 2 Duo OS 10.6.8 want to install HP Officejet Pro 6835 which requires OS 10.7 higher. How can I do this? Possible? Or Is it possible to install 10.7 upper to my Macbook 2.1?

    Lion is the highest version your can install. You need to have 2 GBs of RAM and be running Snow Leopard 10.6.8.
    Upgrading to Lion
    If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
    You can purchase Lion at the Online Apple Store. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
         Lion System Requirements
           1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
               or Xeon processor
           2. 2GB of memory
           3. OS X v10.6.6 or later (v10.6.8 recommended)
           4. 7GB of available space
           5. Some features require an Apple ID; terms apply.

  • HT3625 Hello, If my mac pro only has a "Internal Microphone/Built-in Input" but no "Line In/Built-in Input." where can I get this option?

    Hello, If my mac pro only has a "Internal Microphone/Built-in Input" but no "Line In/Built-in Input." where can I get this option?

    Mosidun 3.5mm Male to Female Audio Cable for iPhone

  • My macbook pro never writes automatically capitalized at a rate beginning. where can I change this to automatically writes big?

    Hi
    my macbook pro never writes automatically capitalized at a rate beginning. where can I change this to automatically writes big?

    That is a feature of specific programs not an Operating System setting. So check the word processing program you are working with for that setting.

  • Officejet pro 8600 plus power switch light stays on while in sleep mode. is this correct?

    officejet  pro 8600 plus  power switch light stays on while in sleep mode. is this correct?
    This question was solved.
    View Solution.

    The power light will slowly flash on and off when the Officejet Pro 8600 Plus is in a sleep mode state.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • HT1338 I have a new MacBook. Pro and never had any issues until yesterday. I can not get it to complete its cycle to. Turn on, where I can log in like normal. I read the reboot in the little manual, but nothing. Please help!!!!!

    I have a new MacBook. Pro and never had any issues until yesterday. I can not get it to complete its cycle to. Turn on, where I can log in like normal. I read the reboot in the little manual, but nothing. Please help!!!!!

    So what happens when you boot it up? What do you get?

  • Need to connect a web cam and external mike to my McBook Pro running snow leopard for a Skype session with another school. Attached an HP webcam (USB) and can't get video. Any suggestions?

    Need to connect a web cam and external mike to my McBook Pro running snow leopard for a Skype session with another school. Attached an HP webcam (USB) and can't get video. Any suggestions?

    -->Click HERE<--  Does item "B" (Turn video on/off) in the last topic on the page help?
    You control the camera for Skype from within Skype, so  Skype must be running to running to make video work.
    Message was edited by: EZ Jim
    Mac OSX 10.7.4

  • Where can i get the Users Manual for the adobe acrobat xi pro

    Where can i get the Users Manual for the adobe acrobat xi pro

    You can find a PDF of the Acrobat XI Manual here: http://helpx.adobe.com/en/pdf/acrobat_reference.pdf

  • I need to use an hp 6215 printer with my mac book pro.  the driver installation disk doesn't work.  where can i get a driver that will work?  i use OS X

    i need to use an hp 6215 printer with my mac book pro.  the driver installation disk doesn't work.  where can i get a driver that will work?

    With the Lion it is essentially unnecessary to resort to external driver disks. What's more, most of those disks are incompatible with the OS and should not be used. The system already carries a wide variety of printer description files (aka PPDs, which is what modern printing systems use as "drivers") for a lot of brands. And there was an HP printer update just two days ago.
    Just checked in mine and did indeed find that the HP OfficeJet 6200 Series, with or without Fax, is covered with the latest update.
    So just go thru the motions of creating a proper printer instance:
    Make sure the Mac "sees" the printer on the network.
    System Preferences / Print & Scan
    Click on the + button on the left column
    Select the appropriate type of printer, will use IP for the rest of this
    Select HP Jetdirect - Socket, default for HP network printers
    Type the IP address or look it up
    Name the printer for easy identification on the print dialog
    Let the Mac identify the printer model or manually choose the driver
    Click Add.
    Once the instance pops up in the list, can click on Options & Supplies for further config.

  • I recorded VCR tape onto DVD-R but will not play on my MacBook Pro. I have already recorded multiple DVDs. How can I get it to play on my Mac?

    I recorded VCR tape onto DVD-R but will not play on my MacBook Pro. I have already recorded multiple DVDs. How can I get it to play on my Mac?

    "I recorded VCR tape onto DVD-R"
    How? Using what equipment/software?
    "The DVD  plays on the device on which it was recorded."
    Just a guess: You're using a VCR-DVD combo recorder. DVDs produced in this way will play on the device that made them, but won't play on anything else until they're "finalized." In fact, Macs will recognize unfinalized DVDs as blank discs until the discs are finalized. Check the manual that came with the recording device for instructions.

  • AD_Link cable for Audigy 4 Pro - where can I get o

    AD_Link cable for Audigy 4 Pro. I lost mine. Where can I get another?Mike

    Your support page says that the customer support number for my region can be found in my owner's manual. The problem with that is my manual is whereever my AD_Link cable is - lost. What number should I call? I am located in Mississippi, USA.Mike

  • Where can I get an additional power source for my MacBook Pro?

    I am travelling to Europe next week and will be travelling on the road quite often. I would like to get some work done during that time. My laptop battery will inevitably run out of power during that time and I would like to carry an additional power source with me so I can get some extra juice when I am nowhere near an outlet.
    I have the latest MacBook Pro where the battery is not removable.
    Where can I get an additional power source for my MacBook Pro? I don't mind if it is a 3rd party product.

    you could get something like this: http://www.amazon.com/Energizer-XP18000-Universal-External-Netbooks/dp/B002K8M9H C
    it's about the same cost as an extra battery used to be. there's a range of similiar products at Amazon, i'd check reviews.

  • I'm going next week to the usa(I'm from Brazil) and i need the logic board for Apple MacBook Pro 15" A1286 where can i get it?, I'm going next week to the usa(I'm from Brazil) and i need the logic board for Apple MacBook Pro 15" A1286 where can i get it?

    I need to buy a logic board for 
    Apple MacBook Pro 15" A1286, but i couldn´t find online to buy it where can i get one and if it´s possible if i can have it delivered to my hotel

    There are a lot of MacBook Pros with the model # A1286 - which year is your model (e.g., "15-inch Late 2011")?
    The only place that I know that you might could score a specific logic board is www.ifixit.com. They may be able to ship to your hotel.
    Clinton

  • I am trying to install windows 7 on my macbook pro 13", when i run bootcamp it tells me that there is not a windows support software available for my computer. Where can i get the windows support software for my macbook?

    I am trying to install windows 7 on my macbook pro 13", when i run bootcamp it tells me that there is not a windows support software available for my computer. Where can i get the windows support software for my macbook?

    Apple only supports Windows on certain hardware.
    http://www.apple.com/support/bootcamp/
    Apple provides their framework for Windows to run on a Mac, a piece of software called a Hybrid MBR that bridges the gap between how Windows reads the drive partition table (MBR) and EFI/GUID partition table that Mac's use.
    It doesn't mean Windows can't run on your Mac, a third party solution called rEFIt will also bridge the gap and allow booting of more that just Windows, Linux as well for a triple booting computer.
    Your hardware has to meet the other requirements the second and third operating system needs as as being able to install drivers that will work for your hardware, especially the fans or they will run loud and fast by default.
    http://refit.sourceforge.net/
    This above is a advanced procedure which requires knowledge how computers and various operating systems, drive formats and so forth work.
    I even admit I don't know everything myself, but I experiment on a separate piece of Mac hardware (out of warranty/AppleCare) designed for this purpose so in case something screws up I'm not taking down my only machine and can use the other to get online and find solutions.
    There is a very high potential for losing your data if your using advanced/non-Apple methods to install Windows on your only Mac where Apple doesn't support it. Also one shouldn't be doing this on Mac hardware that is under AppleCare or warranty as it might be voided. Proceed at your own risk and education.

  • Where can i get the macbook pro (2010) bootcamp drivers for windows 7?

    I recently decided to install windows 7 ultimate (32-bit) on my macbook pro (2010 model). However my macbook did not come with installation disks, i know this for a fact and it came pre installed with 10.6. And when i try to download the windows support files through bootcamp assistant, it says that the download cannot continue. So where can i get these drivers from?

    All MBP's with Snow Leopard (10.6) came with an installaton disc, and that is where the drivers are, if you don't have (or didn't get) the disc contact Apple for a replacement, there is no downloadable version of BC3

Maybe you are looking for

  • How can I use a labview VI as a CVI instrument driver

    I have a VI for the Keithley 485 that would like to convert into a form usable by CVI. I don't have labview so I cannot generate a DLL based on the VI.

  • Export to PDF & Print of Webi document with Xcelsius SWF file embedded init

    Hi , I have embedded an Xcelsius model as HTML in a webi document. It works fine in the Infoview. However, when I export to PDF or print the webi document , the Xcelsius flash component does not show up. I just get a box with the HTML code in it. Ple

  • Default User settings

    I want to change the default user settings in iPlanet Directory Server 5.1 so admins can create individual users in the JAVA Console with the specific attributes needed by our organization per branch point.

  • Monitor ICC Profiles

    Greetings Adobe People! I've been working with Photoshop since version 6.0, I know people quite often use that as bragging rights and I guess, that's what I'm doing, please forgive mefor doing so. Just trying to state in some term that I think I'm so

  • Deadlock - can you make both transactions rollback?

    My understanding of Oracle (11.2.0.3) is that if the engine detects a deadlock, it picks one transaction to rollback and one to succeed. Is it possible to configure a system or session setting that would instruct the engine to roll back both transact