Officejet Pro L7780 Win 7 Driver

I have an Officejet L7800 all in one.  I noticed in your list of Windows 7 drivers that there was a Windows 7 driver available for download yet when I went to the driver download area I didn't see one.  What gives?
Regards,
Bill

i too sometimes need to hard reset the printer, when my wireless computers wont print. Cant figure out why this is so....just has unfortunately become routine....and i have THREE of these printers!!!

Similar Messages

  • OfficeJet Pro L7780 - Have to Restart Print Spooler every job I print (Windows 7 32-bit)

    I have an OfficeJet Pro L7780 that shows as offline in Devices and Printers constantly.  I discovered if I queue up print jobs to it and then restart the print spooler all of the jobs will come out perfectly then the printer will instantly go offline.   Here is what I've done for troubleshooting already:
    Upgrade to newest firmware (R2011NxNxeN0)
    Factory Reset by hold # and 3 at boot
    Changed Ink and Print Heads
    Installed newest 14.0 driver (tried both Basic and IT Pro Driver)
    Rebooted and restarted printer and computer
    Tried all this on a 2nd Windows 7 computer with the same results
    Anyone actually use this printer on Windows 7 32-bit over the wired network port!!?!
    This question was solved.
    View Solution.

    Same printer, same problem, same remediation by restarting Printer Spooler service.  Only difference is OS is Win 7 Ultimate 64-bit.
    FYI- I'm using my L7780 via a wifi connection using WPA2 security and a static IP and network RAW printing to port 9100.  The printer always appears available via network pings but not to the print spooler.  As such, printer is always "grayed out" and disabled but will accept jobs into its queue.
    After endless searching this is what appears to be working as a fix:  Turn off SNMP on printer port.
    Printer Properties -> Ports Tab -> (Select Port) -> Configure Port -> uncheck "SNMP Status Enabled"
    Hopefully this works for others- but I also found mention that others found a fix in toggling other settings such as "Enable bidirection printing" check box.  Who knows what seemingly unrelated software triggers this issue but it began one strange day and drove me crazy.

  • Can't configure Wireless Connection to HP OfficeJet Pro L7780

    I recently purchased both my iMac 24" 2.8GHz computer with OS x 10.5.2 and HP OfficeJet Pro L7780. I was able to use the HP setup CDs for my Windows laptops and configured them to use the printer in a wireless configuration.
    The iMac is creating the headache (actually I think it's HP causing the headache). When I try to install HP's driver 9.7.1 using their utility, it is unable to detect the L7780 in a wireless configuration. The moment I connect via USB or wired Ethernet, the printer is detected without a problem. My printer is located @ 192.168.1.30, fixed IP address via a NetGear FSW308 switch. My iMac is fixed @ 192.168.1.100 and the gateway is 192.168.1.1
    I spent hours on the phone with HP support and am still in the same spot... HP software won't find the printer when it is wireless. I can configure OS x 10.5.2 to use the internal L7700 series driver and put the IP address in the dialog box. The printer prints without issue using the OS printer drivers, but the other features such as scan and fax will not work without the HP software.
    I can ping the printer and I can connect to the printer's EWS, but the HP software will not find the software.
    Overall config: iMac wireless network connection to switch; Printer also wireless connection to switch.
    So far HP is dumbfounded and all they can say is that I should call Apple because the printer software works fine when I connect the Ethernet or USB cables.
    HELP!
    Thanks,
    Roland

    Thank you for the thought. Yes, although my SSID is public, I have a WEP 128-bit security key. The printer, the iMac and my Windows laptops all connect to the wireless network without issue, as evidenced by my Windows laptops and iMac (if I use the driver included with OS X 10.5.2).
    I can ping the printer from the iMac as well as connect to the printer's web interface, so connectivity exists. It is as if the setup software or the printer are trying to communicate using a port that or service that OS X may be blocking.
    My OS X firewall is configured to accept all connections though... so that shouldn't be the issue unless there is a bug in accepting all connections.
    Thanks,
    Roland

  • HP Officejet Pro L7780 - Network Letter Nightmare!

    Hello.
    I'm hopin somebody can help with a problem I am having with my HP Officejet Pro L7780:
    The printer is connected to my wireless network and all is well with this. The problem lies with the network letter that  it assigns itself to on my PC (Windows 7 Ultimate) for the in-built card reader on the printer. It is using the same letter as a virtual cd-rom drive on my PC - and I would like to move the letter the printer uses - and not the cd-rom drive, as I have my PC setup in a way where different types of drives are grouped together. Is there some way (possibly through the Windows registry) that would allow me to change the letter of the network drive (as it seems to automatically assgn one) and keep it using that new letter rather than interfering with the cd-rom drive and denying access to it every time Windows 7 boots?
    Or alternatively disabling the card reader function on the printer as I don't use it?
    Thanks to anybody who can solve this - as it is driving me mad!
    This question was solved.
    View Solution.

    I finally found a solution to this problem that works for me.
    I too have an HP printer that was mapping its memory card slots to a Z: drive every time I booted my Windows 7 computer.
    To change the mapping to another letter to free up the Z: letter, I placed a memory card into one of the printer memory card slots. I then disconnected the Z: drive from the printer mapping (right click the Z: drive in Windows Explorer and choose the Disconnect option).
    I then used the "Map network drive " option on Windows Explorer toolbar to map the printer memory card slot to another drive letter. You have to know the network address (or name) for the printer to do this:   \\[printer network address or name]\memory_card (e.g.: \\192.168.1.108\memory_card). This address goes in the "Folder" textbox of the Map dialog window. Make sure the "Reconnect at logon" option is checked. And make sure you select a new drive letter that won't be needed for anything else later. Then click "Finish."
    After I did this, the printer has continued to use the new drive letter at boot-up instead of Z:, leaving Z: free for other applications.
    I don't think the above works if there is no memory card in one of the printer memory card slot.

  • HP Solution Center for HP Officejet Pro L7780

    I have downloaded the full driver for my HP Officejet Pro L7780 printer trying to get the HP Solution Center so that my printer will be able to scan.  It didn't help.  Any solutions would be greatly appreciated.

    Hi there Jamesis,
    Welcome to the Forums
    I saw your post about the issue you are having with your installation and would like to help where I can.
    1. Perform a Level 3 Uninstall using this HP Officejet Software and Driver Removal Utility. (uninstall_L3)
    2. After the computer restarts, reinstall the printer by using the same driver you posted above.
    Let me know if this helps, if needed, I will help you out further!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • HP Officejet Pro L7780 Solution Center windows 7

    Good Morning,
    I have been trying to install the  Solution center  for a new windows 7computer to run a  network HP Officejet Pro L7780. The CD that came with the printer is only for XP and Vista which won't install.  The installation wizard downloads and unzips a file to my temp folder but no setup program launches and I don't see a file that will install the program.  I also downloaded OJProL7X00_Full_14.exe  fill but can't figure out how to run it.
    Thanks in advance for your help.

    Hi there Jamesis,
    Welcome to the Forums
    I saw your post about the issue you are having with your installation and would like to help where I can.
    1. Perform a Level 3 Uninstall using this HP Officejet Software and Driver Removal Utility. (uninstall_L3)
    2. After the computer restarts, reinstall the printer by using the same driver you posted above.
    Let me know if this helps, if needed, I will help you out further!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • HP Officejet Pro L7780 All-in-One Will Not Print Blue Ink - It Prints Pink Instead

    HP Officejet Pro L7780 All-in-One -
    Issue:
    Blue ink will not print (It prints the color pink instead.).
    Actions taken:
    1.  Cleaned ink heads.
    2.  Replaced ink cartrige.
    3.  Reinstalled software.
    Sugestions by HP customer service:
    Purchase a new printer: Because the issue is software related - not reading the blue ink cartrige.
    Any suggestions or advice would be very much appreciated.
    Thank you for your time!
    Thank you.
    Sincerely,
    Ryan

    The cyan portion of the printhead may be clogged.  I would suggest running the diagnostics shown here.  If three levels of cleaning of the printheads does not resolve the issue you may need a new printhead.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • HP Officejet Pro L7780 All-in-one not scanning with Yosemite

    I have searched for a workaround or fix to the scanning problem I'm having. I just bought a brand new Macbook Pro Retina and have loaded the latest printer drivers for the HP Officejet Pro L7780. The printer works ok, but I can't get the scanner to work. When I try, it says: "Failed to open a session on the device."
    I'm using the printer over a wifi connection.
    Can anyone help with this, please?!
    Thanks!
    peace,
    bart

    Hello,
    This is to anyone else who can help I have the same problem with an Officejet 6500A Plus to the same laptop. It's ....... annoying, HP says nothing and so do Apple.

  • On a HP Officejet Pro L7780 All-in-One printer, is there a toner and where is it?

    On a HP Officejet Pro L7780 All-in-One printer, is there a toner and where is it located? I've looked in Products and Supplies and don't see it but my printer is saying that it's low or empty.

    By now, you have probably discovered that the L7780 does not use a toner but cartridges.  It actually uses 4 HP 88's.  They are black, magenta, yellow and cyan.  Usually, black is the first to be replaced.  They can be found at Staples, Office Depot and Best Buy.

  • HP Officejet Pro L7780 All-In-One printer

    I am running Windows 8.1
    The printer status OFFLINE.
    It has done this in the past and I have been able to correct it by deleting and reinstalling it (at least back when I was running Windows XP and 7.  Possibly at that time it was the DHCP issue pointed out in a previous post.
    Now however, I can remove it and when I add it back, using Control Panel, Devices and Printers, Add a Printer,  it is recognized correctly on the network (shows the IP address I know is in the printer) but when I try to send a test page, I get a pop-up saying it is OFFLINE.  When I status it, it confirms it is offline.
    There is no indication at the printers display that it is offline and it shows it is communicating with the network.

    I can’t give you more than the info in my question about the model of the printer-HP Officejet Pro L7780 All-in-One printer
    I had been using this printer for several years and this has happened a few times in that it required me to delete it and reinstall—that just does not work now. This last time was after I had upgraded to Windows 8.1 however I did that several weeks ago and it has worked okay since then…this is the first time it has stopped working on 8.1 however
    Running Windows 8.1
    I tried connecting via wireless and also switched over to wired lan but got same results (Printer Unavailable)
    Used DHCP but get the same with static ip address
    Cisco Lynksys E4200 wireless router
    Just ultimately get Printer Unavailable when I try to print or status the printer
    When I try wireless, I see the wireless icon bright blue like I expect it to

  • HP Officejet Pro L7780 ink cartridges leaking

    The printer says I need to replace cartridges even though I already did. I discovered the ink is running throughout the printer, over the mother board and out the power supply connection. Has any one else had this problem? 

    Hi WelcomeCenter,
    Thank you for visiting the HP Support Forums. Since this is a duplicate post I'm going to lock this one, please check your other post here for replies:
    HP Officejet Pro L7780
    Thanks!
    Wendy M - HP Support Forums Moderator
    Click the Kudos star as a way to say "thank you" for helpful posts.
    Be sure to come back and click the 'Accept as Solution' button on the post that solved your issue - it may help someone else.
    Rules of Participation

  • HP Officejet Pro L7780 - Registration Problem

    I downloaded and installed the full software for the HP Officejet Pro L7780.  When the software asks to be registered and I put in the printer and the search comes back 0.  I have tried the name and the product number and still keep getting the same result 0.  When I hit enter, the registration goes away and I have this running on my computer.  I can't seem to get it to complete.  Please tell me there is a simply solution to this.  Thanks
    This question was solved.
    View Solution.

    I fixed the problem by terminating the process and everything is right with the world.

  • HP Officejet Pro L7780 All-in-One Printer & Verizon D-Link wireless router. will not connect

    I have a HP Officejet Pro L7780 All-in-one and not able to get it to connect to my Wireless  Verizon D-Link Router.
    Please advise.
    aileensnider

    Let's start here.
    Printer does not maintain wireless connection.  
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&tmp_task=solveCategory&cc=us&dlc=en&la...
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • HP Officejet Pro L7780 won't print individual pages of a file

    I have a HP Officejet Pro L7780 setup with wireless printing on my network and am using Windows 7 on a 64-bit computer with MSWord 2007. I'm trying to duplex print just specific corrected pages (like pages 7-8) from a file (of pages 1-22) and my printer just won't do it. When I select to print specific pages, the printer just sits there and then the print queue is apparently dumped, as the tray icon just disappears.  The printer will print only all pages of a file or nothing at all. What could be the reason for this and how do I correct it? Thanks, Patricia

    Hello tdhoobyar, 
    Please click here to access the troubleshooting steps that should resolve the issue.
    Regards,
    Jabzi
    Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
    Click "Accept as Solution" if it solved your problem, so others can find it.
    Although I am an HP employee, I am speaking for myself and not for HP.

  • Why can't I fax from My HP Officejet Pro L7780 ? ?

    I recently updated to Mavericks and for some reason I can't send a fax through my "HP Officejet Pro L7780 All-in One."
    I used to be able to send faxes from "Word" or other Apps
    When I look at the configuration: "System Preferences" -> "Printer & Scanners" I can add the printer only but I can't add the fax.
    I have checked for software updates and have found none.
    Some one please help.
    Thanks

    This problem has been solved in OS X update to 10.9.3!!
    Thank to ALL!      

Maybe you are looking for