Oh No, My Tecra S2 won't boot!

When I turn on the computer, it displays a back screen and tells me that I need to insert the Windows system disk to boot. Well, way back when I bought my computer, I was not wise to the need to burn a system disk, so I have no disk to insert. Is there any hope for me?

When the boot up begins press F8 and go into SAFE MODE. Maybe F12 for that unit since no full model # given.
You stated no Recovery Disc, call www.toshiba.com and give them your model number to procure a disc. OR, take to an authorized service provider for a diagnostic. Reason it is asking for the disc is to do a REPAIR Function. Is the fan consistently on when you boot? Something you loaded conflicted, was they any service pack installed, new software, or ashutdown on the unit prior to updates being completed, or a power failure there? Something for you too consider.

Similar Messages

Tecra M1 won't boot up at times

This is strange, sometimes it boots up correctly, but some others I wont boot at all. No matter if I'm only on AC, battery or booth, the power on led will light but nothing happens and I can't hear the typical sound of the hard disc running.
Apart from that, I've detected that with the system on if I knock on the flat areas on the sides of the touch panel the laptop reboots and the screen shows artefacts.

On this virtual way nobody can say for sure what the problem is. As Joe already wrote it is hardware related issue and it should be checked by technicians. Fact is that this Tecra M1 is pretty old notebook model (I had it 8 years ago) so I think repair is not a option.

Tecra A4 won't boot - switches off after 3 seconds

Hey all,
I really hope you can help me on this. Recently I bought a cheap Laptop Toshiba Tecra A4 at Ebay. It was said there is a hard drive defect only...it's not.
When I try to switch the laptop on the lamps go on and the DVD drive starts to spin..everything normal. But then after about 3 seconds it switches off before it can reach the bootscreen - like I would remove the power cable.
The very weird thing is that sometimes, let's say every 1 of 15 tries the laptop starts like it should and boots up from my linux live-CD. Then I can work for hours and nothing bad happens ... until I want to switch it on again. Then the game starts from the very beginning.
I already tried to:
- remove the defect hard disk
- remove the power cable only
- remove only the battery
- replace the RAM or use only one of the two
- to remove both RAM
- remove the power cable and the battery overnight to reset the CMOS
...nothing changed.
I would be very pleased if anyone could help me. So far I found only unanswered forum entries with that problem in the WWW - so at least, I am not the only one going mad :-)
Thanks a lot
Hans

Hans
I can't promise that this advice will be of any use to you but your symptoms seem similar to a problem that I had with my Tecra S3 when I tried to run it on battery only after an extended period (months) running only on its docking bay. I found that the battery was not charging properly and ceased to charge after it got to approximately 23% and would fail suddenly under use without giving any warning of battery depletion. When trying to restart the laptop, (before I had determined that the battery was faulty), I had symptoms similar to those you describe relating to shutting off before reaching the boot screen.
I would recommend you try running without the old battery present in the chassis, if the A4 will allow that. If that works for any duration exceeding the short limits you have been experiencing, I would try and temporarily source another battery (preferably with a provable 100% charge) from any source that you can manage. If this proves to be beneficial, you may need to invest in your own new battery. But if not you may have another issue with the physical connection between the power cable jack point and the battery (maybe a dry solder joint that is temperature sensitive). To determine that would probably require Toshiba hardware technical support, or at least knowledge of the motherboard circuits and some circuit testing tools. It could be costly as well.
The very least you need to be able to do if you can restart the laptop for any length of time is to determine the state of the battery using any tools you may have on your Linux live-CD. You might investigate the BIOS version of the A4 and see if that helps by upgrading the ACPI interfaces, but a BIOS upgrade could be risky if you can not get reliable power.
Hope that helps.
Regards Tony

Tecra a3 won't boot with new hdd

hi
tecra a3 model no PTA30E-02G008EN
i have a new 250gb hdd that has a clone of my previous (when working ok) hdd using EASEUS.
but it will not boot. after the BIOS it has a blank screen with a flashing white cursor top left.
the hdd appears ok using a usb caddy.
are there any obvious problems such as a maximum hdd size, or a BIOS update i need? Might it work if a split the 250Gb hdd into two partitions?
thanks for your help
mark

Mark, it's possible (but very unlikely) that your BIOS does not support 48-bit LBA. If that were the case, the partition would need to be less than about 137 GB. The information is in here.
   How to enable 48-bit Logical Block Addressing support for ATAPI disk drives in Windows XP
Notice that large HDDs are offered for the Tecra A3.
   250gb hard tecra a3
Sorry, I don't know why the restored disk doesn't work. You could try to restore it to its original out-of-the-box contents using Toshiba recovery media. I'm guessing that would work.
   Toshiba Europe Backup Media Online Shop
-Jerry

Toshiba Tecra A8 won't boot

My Toshiba A8 PTA83A-04F012 notebook will not boot. When I boot the machine, I get the normal Toshiba splash screen then the screen goes blanks with a blinking cursor in the upper left hand corner. Apart from the CPU fan kicking in, nothing else happens. I've tried to boot from an alternative devices (eg CD-ROM) but the same thing happens. I’ve even tried to get into the bios (setup) but it ignores my request. The keyboard seems to function normally. Please help. Tony

Sounds like it could be ram, try it with only one ram strip at a time, also did you install any software recently that could be not working correctly? Does it work in safe mode? Also in the bios see if the computer is reading the hard drive correctly, or maybe you changed a setting in the bios and need to use the default setings Detailed specs if you need them from toshiba http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?ct=SB&os=&category=&moid=160275...
sorry for all the questions, I want your machine to work

Toshiba Tecra M1 - Won't reboot

Hello @ll
This is my first post on this forum. I write from poland, so forgive me for my poor english.
I have a problem with my old laptop (Toshiba Tecra M1). Computer won't reboot. After the Arch installation everything was fine, command init 6 was working correctly. When I was doing installs and configurations (adds daemon's to rc.conf, modifying fstab, install KDEmod etc.) i was rebooting system to see how it works. I don't know when, but after 3th, maybe 4th reboot system won't boot. I can see the screen which contains information about closing daemons, but after this listing I can see only black screen, computer stops and nothing happens.
Thanks for any advices
Last edited by pmd (2008-08-14 11:59:16)

On this virtual way nobody can say for sure what the problem is. As Joe already wrote it is hardware related issue and it should be checked by technicians. Fact is that this Tecra M1 is pretty old notebook model (I had it 8 years ago) so I think repair is not a option.

Computer Won't Boot Up

Here is my issue, my computer one day was working fine and the next it won't boot properly.
System Specs: Satellite T235D-S1345RD (Laptop) - Windows 7 (64bit) - BIOS 1.7 - 4gb RAM -
I have gotten the computer booted one time. I am unsure why it did that time but did not do it another time.
Since that one time I put the computer in hibernate and when I tried to bring it out it told me it failed when coming out of hibernate so it went to reboot and now won't boot.
Here are the few steps I have done to try and get it working. When it boots up it gives me an error message (says that power failed or for some reason it did not boot)
I have ran "Repair Computer" and it does not do anything. I try start windows normally and it goes no where.
So I then tried F8 and got into the Advanced Boot Menu. First one I tried was Start Windows From Last Known Good Configuration. (or something like that I forget the exact wording)
When it does that the computer will start to boot up go to the "Windows Loading" screen and then it flashes a blue screen (there are words there but it flashes so quickly I cannot read it) and it goes back to the boot screen and acts like it is restarting and continues in that loop.
Next step - Enter F8 again tried "Repair Computer" and it loads to a black screen with a Cursor but nothing ever happens. I have given it over 30 min and nothing happens.
So next step- I enter F8 again and try to boot up in safe mode and again when it loads it flashes a blue screen and then nothing.
EDIT - I found how to show the blue screen. It says UNMOUNTABLE_BOOT_VOLUME. Not sure what else I should do after I get that error message. Message Reads:
It reads UNMOUNTABLE_BOOT_VOLUME and says if it's the first time I've seen the error screen, to restart the computer. Then it tells me if it appears again, to check and make sure any new hardware or software is properly installed.
"If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode."
END EDIT
Next Step: I come to you guys here on this forum. I am a bit perplexed and lost at what to do. I wonder if this is a virus but I cannot get the computer to respond to try to get into it to check.
Ideas? Advice? What should I try? I can get into the F8 menu but not sure what else I should try. I will try anything to get this computer up and running!
Thanks for any and all help.
Lynda

Hi:
The 24 character failure ID usually indicates HDD is failing/has failed. You need to replace it with a new one.
Specs: http://support.hp.com/in-en/product/HP-Pavilion-dv6-Entertainment-Notebook-PC-series/5191856/model/5...
Manual: http://h10032.www1.hp.com/ctg/Manual/c03099531
Check warranty: http://h10025.www1.hp.com/ewfrf/wc/weInput?cc=us&lc=en
Order recovery USB: http://support.hp.com/in-en/product/HP-Pavilion-dv6-6c13cl-Entertainment-Notebook-PC/5191856/model/5...
Contact HP: https://support.hp.com/in-en/contact-hp/product/HP-Pavilion-dv6-6c00-Entertainment-Notebook-PC-serie...
If you're under warranty, HP would send you replacement HDD.
If you're not, buy any branded 2.5" SATA 9.5mm thick internal laptop HDD and replace it yourself. But HDD of at least same capacity HDD as the one that came with your laptop (640gb) so that recovery media would work -
Go through page 56-58 in the Manual for replacement procedure. It's quite simple DIY job.
Something like this:
http://m.newegg.com/Product/index?itemnumber=N82E16822236561
If you've not yet created the Recovery media to restore the factory settings after replacement, you have to order a set of Recovery USB from HP.
For salvaging the data from old HDD, I suggest you take out the drive. Connect it to another PC using SATA to USB adapter - copy all the files you need.
http://www.amazon.com/Anker®-Converter-Adapter-Cable-included/dp/B005B3VO24
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Satellite m300 won't boot! please help!

Hi,
I've got a bit of an issue here.. I have a Satellite m300.. a white one..
and it won't boot... I've had this very issue before but it turned out to be an external USB HDD that stopped it from booting up but now even with everything removed it still won't boot.
And it was fine until yesterday, it just gave up.. I am away from home for work so I have all the work stuff and unfortunately without my recovery cd, but my guess is that it won't even read it..
So this is what happens..
turn on..
all light come on.. including power and all the white lights around the keypad..
and then maybe 5 sedconds later caplock and numlock(?) green lights flash..
then it's a dead still.. no HDD activities or sound.. just dead quite..
the screen remains black blank through out..
it seems to get stuck here before reaching the post screen.
i thought the power button usually took more than just a push to turn off? it instantly swithces off with a single push of the power button..
I think this laptop is like on sleep or something and can't seem to wak up.. maybe?
And it has vista.
Please help.. I have some important work files I need to recover at least before formatting..
and that has to wait till I get home which won't be for a month or so..
which also lets me take it back for warranty as well..
any help appreciated!!!
cheers,
Min

Quote
Originally posted by syar2003
If running a LCD display with DVI connection , try to hook it up with
an analog VGA cable.
Can also be that the motherboard fails to initialize the vga AGP card.
Turn off all power incl. AC .
Disconnect all devices from motherboard : AGP/memory/drives/floppy/USB/PCI cards etc. take out the 20pin & 4pin PSU connectors and reset the motherboards
cmos .
Assemble PSU connectors ,only one DIMM module and graphics card and turn it on and se if you get a post .
Just removed all components. I reset the CMOS. I then reconnected the 20pin and 4pin, 1 stick ram, and the video card (no ide devices, no mouse, keyboard cd drives) and the monitor doesn't show up. I also tried another monitor so it isn't the monitor.
Could it have a bad AGP port?
Any other suggestions? I am thouroughly stumped. Also the power and reset buttons don't work no matter what configuaration I put the front panel connectors in. The Power LED is lit up and it doesn't work and the reset light is off and it doesn't work.
Also noticed one of my fans connected to one of the two other fan pins on the motherboard isn't working.
What a nightmare.

Mid 2010 MacBook Pro won't boot past blue screen

I've been having problems booting up my MacBook. I can't get past the blue screen. It went from booting slow at the grey apple logo screen to not booting up at all. Is it a problem with my hard drive? I also have boot camp running as well, but I can still see the boot camp drive for windows and my OS X drive, as well as my installation disk when I have it inserted when I hold the option key at start up.
I'm still able to run windows on it without any problems when I pick the windows drive. I tried different methods from different forums but I'm just not getting through. I tried holding 'c' to boot up from cd and I let it run over night but it never got past the grey apple screen with the gradient wheel (still spinning). I had already used time machine to back everything up before this happened since I was able to boot up properly (but slowly). Can anyone help? It's driving me nuts, and I can't remember what os/firmware version I'm running.

n your signature you said you are running 10.6.3. So let’s assume you are running Snow Leopard.
It sounds like your diagnosis of disk problems is correct. The OS X partition may be corrupt.
Try booting in Safe Mode.
http://support.apple.com/kb/HT1564
Try again to boot in normal mode.
If it will boot in Safe Mode but not in normal mode then you could have some 3rd-party software preventing the boot or you could have a corrupt disk or OS.
Boot as from the startup manager (Boot - option) and then select the installation disk.
Hopefully that will work better than starting with the Boot-C option.
Then try to repair the system disk.
Start the Disk Utility.
Perform the steps in http://support.apple.com/kb/PH5836.
If it repairs OK but still won’t boot reinstall OS X.
Installing Mac OS X 10.6 SnowLeopard
http://kb.iu.edu/data/akav.html

MacBook Pro Retina 15" mid-2012 won't boot in clamshell mode with an external display attached

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

IMac shut down suddenly and won't boot back up

This morning my iMac shut down suddenly. All I had open was Google Chrome and I was just on Facebook and that's it. When I tried to boot it back up, it wouldn't load past the startup sound, wherein it would appear to shut back down,or at the very least the screen would go black (my mouse has lights that stay on when the computer is on, and the light kept going on and off while the screen remained black). This was the case for at least a half hour until it suddenly booted itself back up all on its own. I had it on throughout the day, just browsing the internet and watching Youtube. It shut itself down twice during the day, and both times it restarted on its own right away after showing me a grey screen with the Apple logo and a progress bar. Now it just shut itself down again and it won't make it past the progress bar screen - if it even makes it that far, sometimes it shuts off right after it makes the startup sound. It keeps trying to boot up on its own over and over again, but it keeps shutting down right away. All the fixes I've searched for so far require a computer that actually boots up all the way so I don't think I could run any reports if I tried!
I'm running the latest version of Yosemite (10.10.2?).
Model number A1311
Not entirely sure what specs are useful to know so I'm just gonna write some of what's on the box it came in:
3.2 GHz Intel i3 processor, 4MBshared level 3 cache
4GB of 1333MHz DDR SDRAM
1TB serial ATA hard drive
ATI Radeon HD 5670 graphics processor with 512 MB of GDDR3 memory
Bought it around fall of 2010. Not sure if it's worth trying to get it fixed (I live nowhere near an Apple store) or if I should just get a new computer, but I would like to know what's wrong, if possible.

Try to boot into the Recover Partition by holding down the Command + R keys on startup. If it still won't boot then the HD has probably crashed. The is likely a AASP in your area, you can locate one by clicking AASP Locator, take it to one to be professional diagnosed. If it's only the HD, assuming you have been backing up, restoring to a new HD is pretty simple.

[865PE NEO2 PFISR] Won't boot with added memory

Recently I upgraded a few items on my PC which has been running fine for 18 months or so. I changed out the video card and bought double the memory of the same brand and type it had in it. I went from 1gig (2 sticks) and added two more sticks. But now it won't boot. The power is on but no output whatsoever.
I RMA'd the memory thinking that might be the problem but it's the same with the new set. I tried all sorts of memory/slot combos. Basically, the new memory works fine if you swap it out in bank A with the old stuff. That's how it's running right now, so I know all of the sticks are good. I can take a third and put it in either slot bank B and it'll boot, but obviously not run properly. But any combination of these four sticks and the system won't boot!
Please help!
I'm running this system:
Win XP (SP1 I believe)
865PE NEO2 PFISR
P4/3.0CGHz, 800M 478P/512K HT
DDR Corsair 512MB X4 (400)
Dual 80gb samsung HDs running SATA
Sapphire X800GTO 256M video card
Antec Sonata case
TruePower 380Watt ATX12V

What brand, model, and speed are the RAM sticks. Did you check your Test Report booklet which came with the mobo. If you can't find it, you can go to the MSI website and look for your MOBO and get the test report that way. Some brands/models will that have been tested are shown in the report to be okay in all 4 slots, some only test okay in 2 or 3. Check this report and if it is one of the brands/model/speed tested you will see how it fared. It may well be you the MOBO doesn't like your RAM in 3 or 4 slots.
Maybe I missed it, but did you try each slot with only one stick at a time? You may also have a bad RAM slot.

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
I have tried these:
1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
2. I tried putting back my old 2.5" and nothing but black screen.
Thoughts and suggestions?
Solved!
Go to Solution.

Hi Autoexit173,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
As you have mentioned that the system not booting, please try to remove the RAM and turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
Click here for the steps to remove the RAM and refer page number 40.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

My Macbook Pro won't boot up, I don't have any discs...bought from Craigslist

I bought my Macbook Pro (2012 model) from Craigslist and only had it about a week, but this morning I couldnt boot it up. I didnt get any discs with this computer. Only the powercord. What can I do to get it to boot up and where can I go from there? There was a software update last night and this morning it won't boot up. Is my only option going to Apple Store? Is there anything else I can try to at least get it to boot up?? Thanks so much.

Yea, it has Mountain Lion on it. I have tried starting while holding down Command-R, and also the Comand R, Option P, and still won't let me boot up. I made an appointment for a Genius Bar... Is this who I make the appointment with for help with this? We checked the seriel number from "About this Mac" and we went to view that it had a few years left of apple care. It happened right after a software update. Wonder if that caused it. Is there viruses out there for Mac's and should I have a program to clean it up after I get it going or IF I get it going tonight? Thanks,
Curt

Hi guys I'm really in need of some help. I have an IMac I3 for a while now I've been having a problem of my machine refusing it shut down , it goes to a blue screen with a spinning wheel but doesn't shut down. And now won't boot from install DvD

Please some one help me ...
A) my mac won't shut down with external HD connected (if it's been used)
B) there are disk permissions that can't be fixed SUID stuff ..
C) I have now verified the Mac HD and it tells me it's corrupt in bold red writing and to start up from install DVD
D) it won't boot from DVD so I cannot run the repair , initially the machine was spitting it out on start up , now it appears to be attempting to boot off DVD , well it sounds like it is .... BUT it's hanging with the Mac Logo and a wheel ... For um .... 30min now...
E) weirdly when OSX is booted off the hard drive , it won't recognise the Install DvD or the applications one... It just spits them out....
I had an old PPC 17" and it was a beaut .... Never had a single problem with it ...
I bought this one December 2010 and it's been nothing but issues for a computer in excess of £1000 I'm extremely disappointed ... And weirdly the shutting down issue started when it was a week out of warrantee ... I feel conned and am almost at the point of throwing it at a wall and buying a PC

Ok so I've done what you said and this is what it's come back ....
I don't know that these are the errors , but they're the things which don't look right ...
Throughout the shut down there is a recurring line ;
It says ;
Com.apple.launchd 1 0x100600e70.anonymous.unmount 301 PID still valid
Then there are 2 more which I think are related ;
Com.apple.securityd 29 PID job has I overstayed its welcome , forcing removal.
Then the same with fseventd 48 and diskarbitrationd 13
Oh and on Launchd1 : System : stray anonymous job at shut down : PID 301 PPID13 PGID 13 unmount...
Then the last process says "about to call: reboot (RB_AUTOBOOT).
Continuing...
And stops ...
Hope this means something to you ... Thanks again for your help so far :-)

Oh No, My Tecra S2 won't boot!

Similar Messages

Maybe you are looking for