Oh No, What have I done

After getting my dreadful speed sorted with the help of the mods I have gone and trashed it by changing routers for a BT business hub!
My speed was almost 2.5 now its only 1.2. I quickly swapped back to my old router but its made no difference,
here are my stats
Internet Details
Broadband Link Type:
Built in modem - ADSL
Connection Type:
PPPoA
User Name:
[email protected]
Current Internet Connection:
IP Address:
86.132.144.6
Subnet Mask:
255.255.255.255
Default Gateway:
217.47.79.250
Primary DNS:
213.120.234.66
Secondary DNS:
213.120.234.6
Host Name:
Domain:
MAC Address:
MTU:
1500
DSL DetailsDown Up
Modem Type:
Built in modem - ADSL
DSL Line (Wire Pair):
Line 1 (inner pair)
Current DSL Connection:
Rate:
1888 kbs
448 kbs
Max Rate:
1960 kbs
648 kbs
Noise Margin:
6.0 dB
12.0 dB
Attenuation:
62.5 dB
31.5 dB
Output Power:
17.1 dBm
12.3 dBm
Protocol:
G.DMT Annex A
Channel:
Interleaved
DSLAM Vendor Information
Country: {46336} Vendor: {TSTC} Specific: {4101 }
ATM PVC:
0/38
Rate Cap:
1960 kbs
Attenuation @ 300kHz:
62.5 dB
Uncanceled Echo:
-7.9 dB
Ok
VCXO Frequency Offset:
18.5 ppm
Ok
Final Receive Gain:
34.5 dB
Ok
Excessive Impulse Noise:
0
Ok
Traffic Statistics
Bytes Packets Errors %Cells Errors %
IP Traffic
Transmit:
820265
26
0
0
Receive:
2264807
3086
0
0
ATM Traffic
Transmit:
20319
0
0
Receive:
50043
0
0
DSL Link Errors
Collected for 3:50:48
Reset 24-hr int. 15-min int. Last Event
Since
Current
Current
Time Since
ATM
Last Event
Cell Header Errors
2
2
0
0:35:03
Loss of cell Delineation
0
0
0
0:00:00
DSL
Link Retrains:
0
0
0
0:00:00
DSL Training Errors:
0
0
0
0:00:00
Training Timeouts:
0
0
0
0:00:00
Loss of Framing Failures:
0
0
0
0:00:00
Loss of Signal Failures:
0
0
0
0:00:00
Loss of Power Failures:
0
0
0
0:00:00
Loss of Margin Failures:
0
0
0
0:00:00
**bleep**. Seconds w/Errors:
3
3
0
0:35:03
**bleep**. Sec. w/Severe Errors:
0
0
0
0:00:00
Corrected Blocks:
10009
10009
179
0:00:03
Uncorrectable Blocks:
4
4
0
0:35:03
DSL Unavailable Seconds:
90
90
0
3:49:17

Too many disconnects in succession ( swapping routers, resetting and switching them off etc) will have alarm bells  ringing with line management and will slow your connection down to find stability.  Leave it alone for 3 days+, it should return. 
Time of day you did this can play a part however I have always found you will get what your line can support, in the end!
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

Similar Messages

  • I found how to delete a series from my ipad, but it still won't download the last episode of the new series I am trying to have.  What have I done wrong?

    I found how to delete a series from my ipad, but it still won't download the last episode of the new series I am trying to have.  What have I done wrong?

    What is the GarageBand version that your friend is using?
    If it is GarageBand '11, version 6.0.5, you can buy GarageBand '11 as a boxed retail version with the iLIfe '11 bundle, e.g. from Amazon.
    Then you can upgrade GarageBand '11 to 6.0.5, using this upgrader from the Support page:
                     GarageBand 6.0.5
    GarageBand 6.0.5 will work well with your system.  But if your friend is using the newest GarageBand 10, this will not help. Then ask your friend to send you audio files for each track, so you can recreate the project from the audio.  Or your friend could also use GarageBand '11 for the projects you want to share, that will run well in all newer MacOS X versions, even with GarageBand 10.0 installed on the same system.
    -- Leonie

  • I have done something terrible!  nopen up, 'event'  but if I click on them a triangle with an exclamation point comes up.  What have I done, how can I get them back?

    I have done something terrible!  now some of my photos will not open up, I can see them in the 'event' but if I click on some of them I get a gray triangle with an exclamation point.  What have I done and how do I rectify it? 

    The exclamation shows when the file path/link to the original file has been broken.  Apply the two fixes below in order as needed: 
    Fix #1
    Launch iPhoto with the Command+Option keys held down and rebuild the library.
    Since only one option can be run at a time start with Option #3, followed by #4 and then #1 as needed.
    Fix #2
    Using iPhoto Library Manager  to Rebuild Your iPhoto Library
    1 - download iPhoto Library Manager and launch.
    2 - click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
    3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option.
    4 - In the next  window name the new library and select the location you want it to be placed.
    5 - Click on the Create button.
    Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments.  However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
    OT

  • I have 4 mail icons on my desktop and cannot open any of them.  I have no idea how I have done this but want to go back to having one mail icon which opens.  What have I done and what should I do?

    I am new to mac pro and have managed to set up 4 mail icons on my desk top and none of them open mail.  What have I done and how do I get back to having just one in the doc which opens?

    HA! It turns out, that an app that I've never used before, became active during a time that I was multitasking and didn't realize it. I didn't notice the effects right away, because my main desktop has a special 3D desktop generator called, bumptop, which covers over any other desktop color or graphic in that area. So it wasn't until I swiped to go to a different desktop, that I noticed the random slideshow being displayed. All fixed now. What a relief.

  • IPad 3 light leak under the bezel? What have you done about it?

    If you have an iPad 3. Tilt towards you, looking underneath the bezel (under the camera) has your iPad got any lights showing? It's not bleeding onto the screen, in fact it doesn't interfere at all under normal use of the iPad. I have read many forums and it does seem to be quite common,but i would like to know what have you done about it? Have you replaced within 14 days and got a brand new iPad and been satisfied ? Or have you had another with worse or different issues? Or have you ignored the issue and kept the iPad?
    I walked into comet and the first iPad 3 I picked up had exactly the same issue. I asked the bloke, he said yes? It's no problem, it's common in led screens and with the iPads new retina screen your bound to get this problem on some but it's no problem as doesn't effect your everyday use. Not the point though is it, we pay 400-579 for this thing!
    I also rang apple and they spoke with their technical team and they came back and said the lights under the bezel seems unusual. To try and restore the iPad and see if that solves it. Solves a hardware problem?? How did they get their jobs? Crazy. So now I am in the middle of returning the iPad for a replacement but I am debating whether to even bother as I have read a lot of replacements people have received have numerous other problems, like dead pixels, light leakage, scratches.
    I would appreciate any feedback from those who have had this same issue and what did you do about it ?

    Mine has some along the right side. It is very slight, and does not affect the screen,even with a black image displayed in a dark room. So I chose to ignore it. This iPad will be going back though, as the bottom half of the screen has a pink tint on it. My advice is to see if it affects a dark picture in a dark room. If it doesn't, I would keep it. But in the end, you have to make your own decision and be comfortable with it. :)

  • I recently did an update to my iphone 4s and now i have lost all my custom ringtones and some music I had loaded. What have I done wrong ? I did a backup and restore.

    I recently did an update to my iphone 4s and now I have lost all my custom ringtones as well as some music I had loaded. I did a restore and backup but nothing changes. What have I done wrong?

    Hello Chance1985,
    Sorry for your wait. Okay so let's try re-connecting with iTunes on your computer and syncing your device. This may give you all your stuff back. Sync in Music tab.
    ^Connor

  • Where are all my bookmarks - what have you done with Mozilla? you have screwed up my computer!

    Everything I had on my tool bar, and all the sites listed in my Bookmarks are GONE!!!
    What have you done with those sites? They were very important to me - I can not handle all these changes by Mozilla - None of these changes are of any use to me. I want to go back to my original screen and when I logged on today you would not let me access my internet and original screen without entering info that changed everything on my computer window!!! Help me find those BOOKMARKS
    Mozilla Firefox is not user friendly - I don't want all these apps - EBay, Weather or YouTube! I had the necessary sites listed that are important and used everyday - not those listed. Who are you to determine what "apps" I should be using???
    edit: email address edited out but it is likely too late for search bots grabbing it.

    I'm desperate to get back my Bookmarks in the same unsorted way and easily accessible as I had previously - at the moment they are hidden away in some sort of zipped form I am unable to access: they were previously listed in the ideal way for me to access - as chronologically bookmarked and disparate. It really is infuriating to have this level of interference with my personal affairs on my computer without even seeking my consent. Ideally I want a return to the earlier version of Firefox which worked perfectly well for me - I'm plagued with excessive slowness and freezing since the latest -Firefox 5.0- update was installed. Is there any simple way to revert back to the earlier version of Firefox?

  • Apple, what have you done? 8.01 makes my ipad seems like it is back on dial up. Don't fix what ain't broken, or is your policy break it so we have to fix it?

    Apple, what have you done? 8.01 makes my ipad seems like it is back on dial up. Don't fix what ain't broken, or is your policy break it so we have to fix it?

    Hi The best option is to do a factory Reset this will get rid of any bugs And set up iPad as new. Just use same Apple ID you will get all your Apps & Data back. Do this over Wifi Cheers Brian

  • HT1386 I have a new computer. I have copied Itunes library from an external hard drive. Itunes now tells me I cannot sync with my Ipod as it thinks the 20gb on the computer are different to the 20gb on my Ipod touch! What have I done wrong? How can I fix

    I have a new computer. I have copied Itunes library from an external hard drive. Itunes now tells me I cannot sync with my Ipod as it thinks the 20gb on the computer are different to the 20gb on my Ipod touch! What have I done wrong? How can I fix it?  Alan

    See:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
    Sync Your iOS Device with a New Computer Without Losing Data - How-To Geek

  • I own Adobe Creative Suite 5 Design Premium Upgrade and I bought the upgrade to Adobe Creative Suite 6 Production Premium but it wont work with my serial number what have I done wrong

    Hi Mark,
    I own Adobe Creative Suite 5 Design Premium Upgrade and I bought the upgrade to Adobe Creative Suite 6 Production Premium but it wont work with my serial number what have I done wrong
    Mick

    Moving this discussion to the Downloading, Installing, Setting Up forum.
    Aussimick you will want to enter in the qualifying serial number from the full version of Adobe software you purchased.  You can find the serial numbers located under your account by following the steps listed in Find your serial number quickly - http://helpx.adobe.com/x-productkb/global/find-serial-number.html.

  • I am connected to my iMac to recharge iPad but it is saying "Not charging" ! Why and what have I done wrong?

    I am connected to my iMac to recharge iPad but it is saying "Not charging" ! Why and what have I done wrong?

    If you already updated to 8.0 you're doing nothing wrong. It's one of the lovely issues created by the update. I just tested mine, same problem.

  • HT5361 When inserting pictures in a new mail message using the " photo browser" button I can view and select photos but the " choose "  button is gone. What have I done wrong?

    When inserting pictures in a new mail message using the " photo browser" button I can view and select photos but the " choose "  button is gone. What have I done wrong?

    Hi Liz,
    Sorry to hear you are having a similar problem.  Last night I went to the tool bar at the top of iphoto, clicked on "File",  then clicked "Browse Backups" in the drop down menu.    I have an external hard drive that is set up to Time Machine.   The Browse Backups  opened the iphoto pages in the Time Machine.  I selected a date one day ahead of the day I performed the now infamous update, and it showed my iphoto library as it had existed that day.   I then clicked  "Restore Library" at the bottom right corner of the Time Machine screen.   Roughly 2 hours later my iphoto was back to normal.   When I opened iphoto there was a message saying I need to upgrade my program to be compatible with the new version of iphoto(version 9.2.1).  I clicked "Upgrade" and within seconds it had done whatever upgrading it needed to do. 
    The only glitch in the restoration was that it restored the library as it appeared last week, so I no longer had photos I had imported this past weekend.   I simply went back to the Browse Backups in the drop down menu,  when Time Machine opened I selected the page showing my pictures from this weekend and again said to Restore Library.   Roughly 45 minutes later the library was restored including the most recent photos.  
    I am now a happy camper. 
    I don't know if any of this will be of help to you because your email says you are having trouble with photos imported after the upgrade was performed.   Have you had any pop up notices when you first open iphoto,  that tell you you need an upgrade to be compatible with the new iphoto?     If so have you clicked "upgrade"? 
    Good luck Liz,  if you have Time Machine running as a back up to your library, maybe you wil be able to get help there, by following my instructions above.   Otherwise,   good luck with your investigations.   I'd be interested in hearing how you make out.
    Karen

  • The screen goes blank when I press to enlarge while watching netflix or a TV show.  What have I done?

    The screen goes blank when I press to enlarge while watching netflix or a TV show.  What have I done?

    Have you tried resetting the iPad:
    Reset iPad:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.

  • TS3276 Help!! I'm a fairly new MAC user. My Email has frozen on the computer. I cannot close Email to do a reboot. what have I done wrong and how do I correct the problem. My server is obviously working. thanks, Sharon

    My Email has frozen. I'm unable to close Email so I'm unable to reboot the computer. I'm a fairly new Mac user. What have I done wrong? And how do I resolve the issue? thanks, Sharon

    Force quit. cmd-option-esc key combo. Then choose Mail and force quit in the window that presents itself.

  • CASE statement... problem using it... what have I done to deserve this?

    I'm trying to use a CASE statement in Ora 8.1.7 (with compatible
    set to 8.1.0) and am finding that I cannot compile the
    procedure.
    I'm using the CASE statement in a call to a procedure...
    insert_addr (p_id_number => v_id_number,
    p_addr_type => v_addr_type,
    p_addr_status => v_addr_status,
    p_addr_pref_ind => v_pref_addr_ind,
    p_date_modified =>
    (CASE
    WHEN cmf_rec.hadoc = cnv_constants.nov17_1958
    THEN cmf_rec.doe
    ELSE cmf_rec.hadoc
    END)
    I'm getting "PLS-00103 Encountered the symbol "CASE" when
    expecting one of the following..." error msg when compiling.
    What have I done wrong? Syntax error? Should I change the
    compatible parameter?
    Thanks.

    You can actually use the CASE statement in Pl/Sql, though not like in SqlPlus.
    You have to use dynamic Sql.
    Example
    create or replace procedure test_case1 is
    v_sql varchar2(4000);
    begin
    v_sql := 'update case_test set qual_rule = '||
             '(case '||
             ' when dob < ''01-jan-1902'' then ''100+'' '||
             ' when dob between ''01-jan-1902'' and ''31-dec-1912'' then ''90-99'' '||
             ' when dob between ''01-jan-1912'' and ''31-jan-1932'' then ''70-89'' '||
             ' when dob between ''01-jan-1932'' and ''31-jan-1952'' then ''50-69'' '||
             ' when dob between ''01-jan-1952'' and ''31-jan-1972'' then ''30-49'' '||
             ' when dob between ''01-jan-1972'' and ''31-jan-1984'' then ''< 30'' '||
             ' else ''under age'' '||
             ' end ) ';
    execute immediate v_sql;
    commit;
    end test_case1;

  • Slideshow - does not run! What have I done wrong?

    It's stuck on the first image, does not run to the next.
    Can't remember that I done any changes. What have I done wrong?

    Perhaps an over simplified question, but have you selected more than the first image? Slideshow only runs for the images selected, and not all images in an album or project, unless selected. Sorry if this is too basic.
    Ernie

Maybe you are looking for

  • File Permissions randomly changing

    We have a small network with 3 machines connecting to our mac mini (snow leopard) server to access work stored on on it. We have a problem when any one of the machines saves work to the server it rewrites the permissions to be read only and non of th

  • Pulling up the proper tracking number for ordered printer delivery

    Having problem in pulling up tracking no. to find out when my ordered printer will be delivered. The order  no.is BDTZ9337--I got an email supposedly telling me how to do it, but it doesn't make sense--please spell out exactly how I get that tracking

  • Universe Design using external join strategy

    Hi, I need to design a universe based on the joins in Database(Database Referential Integrity). I am selecting the External join strategy(Database Constraints) and in the options "Database", I have selected retrieve the joins with the tables. But whe

  • ISight voluntarily disconnects itself

    Hi, I'm using MacBook Pro 15" 4,1 version. I'm using Hardware Growler, so I'm notified when a device is connected/disconnected from my Mac. After updating to 10.6.3 my internal iSight started disconnecting itself on regular bases. It's more probable

  • JSObject error in c# reflection

    hello, I'm using c# and Javascript object to do some pdf manipulation. Please see the below code, I ran into an "Unknown Name" error at the last line when trying to get the "children" object from the BookmarkRoot. Getting the "name" and "color" worke