OID FOR SWITCH 2530 & 1910

Good day all, i am looking for a list with oid from the specific products.HP 2530-48G Switch (J9775A)HP V1910-16G can you please inform if there is any library for OID or something else that could help me? Thank you in advance.

Hi: You may also want to post your question on the HP Enterprise Business Community Support Forum -- Procurve Switches section... http://h30499.www3.hp.com/t5/ProCurve-ProVision-Based/bd-p/switching-e-series-forum#.VbIl-pXbK9I

Similar Messages

Specific OID for A radio modules on 1200 series access points

Is there a specific OID for A radio module cards of the following type:
Flap - AIR-RM21A-A-K9
Dipoles - AIR-RM22A-A-K9

No switches in Cisco's current product line provide enough power to support both radio modules in the 1200 series. The (now optional) power injector for the 1200 will provide enough inline power for both radios, if that is an acceptible option.
Cisco has plans for several switches that will be able to provide inline power to both radios, but I am not aware of ETA's on these.

Need the Cisco ASA5520 SYS OID for the LLDP protocol

Hi :
I need the Cisco ASA5520 SYS OID for the LLDP protocol so that I can create the network connection between Cisco ASA5520 and the 3rd party networking device in this 3rd party network management management system.
Can anyone help on this?
I tried to search the web and got some LLDP MIB files but they all cannot solve the problem. What I think and I need to have now is the SYS OID number for this Cisco ASA5520.
I know that the SYS OID for ASA5520 is 1.3.6.1.4.1.9.1.670. Now I need is the SYS OID for its LLDP protocol. Can someone help on this?
Many thanks!
tangsuan

Hi Afroj Ahmad:
I think it is not due with command line. It is the lack of OID information for Cisco ASA5520 to be able discovered by 3rd party Network Management System.
If I am not wrong, the ASA5520 should have been configured correctly for providing SNMP to the 3rd party network management system (NMS) and as such, the NMS is then able to capture the the SYS OID for ASA5520 is 1.3.6.1.4.1.9.1.670 from the ASA5520.
The SNMP configuration is as below:
snmp-server host inside 172.16.0.82 community public version 2c
snmp-server host inside 172.16.8.50 community public version 2c
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
snmp-server enable traps ipsec start stop
snmp-server enable traps entity config-change fru-insert fru-remove
snmp-server enable traps remote-access session-threshold-exceeded
The 3rd party NMS can capture the product OID from ASA5520 after given the ASA IP address to the NMS. It is the LLDP OID that is not included in the product OID to cause the 3rd NMS cannot link up the LAN connction between the ASA and the 3rd party switch. There is no LLDP configuration in ASA command. I believe the LLDP should be provide externally either by key in manually or upload the MIB file to the 3rd party NMS. I have tried also uploading few MIB files but all not succesfully done.
I think the direct method is just key in the LLDP OID inside the 3rd party NMS system so that the 3rd NMS can embed the LLDP information into its operation kernel then the NMS can link up the LAN connection between the Cisco ASA and its switch.
Many thanks!
tangsuan

Looking for OIDs for 2960s Temperature and Fan

Hi all
I'm looking for the OIDs for FAN, Temperature and Powerstate of each 2960s Switch in a Stack.
I can do a
show env switch 2
But were ist the OID für these "counters"
Thanks
Willem

Hi Ganesh.HThanks, this is what I was Looking forTemp:IOD: 1.3.6.1.4.1.9.9.13.1.3.1.3.1008 for the first Switch, 2008 for the second ...Return. Value CelciusFAN:IOD: 1.3.6.1.4.1.9.9.13.1.4.1.3.1007 for the first Switch, 2007 for the second ....return: 1= NormalPowersupply:OID: 1.3.6.1.4.1.9.9.13.1.5.1.3.1006 for the first Switch,1007 for the second .....return 1 = NormalWillem
Hi Willem,
That Great post has helped out ..it will be helpful if you can mark this thread has answered so that others get benifitted !!
Ganesh.H

OID for all the cisco network devices

Hello All,
Can anyone provide the list of OID for all the network device with device name for routers,switches, WLC, WAAS etc.
Regards,
ADM

Anshumaan,
the cisco-products-mib is what you're looking for, and should be dowloadable without having a cco account (I believe all of the mibs can be downloaded with an account).
chris

Is it possible to use the same OSSO/OID for multiple R11 and R12 instances?

Hello guru's,
We have multiple R11and R12 instances that should be configured for Oracle SSO 10.1.4.3. For OID, we are still trying to decide between OID 10.1.4.3, or OID 11g. OAM is not an option because we also also need OSSO integration with Siteminder. We will also need to SSO-enable Discoverer an Forms.
I have successfully configured SSO for a single-instance EBS R12, but not for multiple instances, let alone include R11 and other components into the mix.
Do you have any special tips, guidance or lessons learned when SSO-enabling multiple instances into the same SSO/OID?
Thanks!
Maria

Interestingly, the article talks about using the same SSO/OID for EBS, JD Edwards, Peoplesoft multiple R11 instances, but did not mention 'multiple EBS versions'. Am I just being picky or there was a reason for it not being mentioned?In Steven Chan blog (in the same link), see the following:
Comprehensive Single Sign-On Solution+
If you have one or more E-Business Suite Release 11i instances and are tired of maintaining users separately for each environment, you can create a central OracleAS 10g environment and manage all 11i users in one place.
If you have a combination of PeopleSoft, JD Edwards, and the E-Business Suite in your organization, you can use OracleAS 10g to manage users for all three environments centrally.
If you have a combination of the E-Business Suite and custom applications based on Oracle databases or OracleAS 10g technology, you can use OracleAS 10g to manage users for all applications in a single place.
Thanks,
Hussein

Enum class not supported for switch() statement in 12.4 beta?

Hi fellow 12.4 beta testers,
It would appear "enum class" isn't supported for switch() statements in the 12.4 beta. This compiles fine under clang and g++. Will this be fixed for the final release? This currently causes compile errors for us, since __cplusplus >= 201103L evaluates to true, so our code uses "enum class" instead of plain "enum". It looks like the C++11 standard says it should be supported:
   Switching on enum class in C++ 0x - Stack Overflow
Many thanks,
Jonathan.
$ cat test.cpp
#include <iostream>
enum class Ternary { KnownFalse = 0, KnownTrue = 1, Unknown = 2 };
int main( void )
   Ternary foo;
   switch ( foo ) {
      case Ternary::KnownTrue:
      case Ternary::KnownFalse:
      case Ternary::Unknown:
         std::cout << "Success\n";
$ clang++ -std=c++11 test.cpp
$ g++ -std=c++11 test.cpp
$ /opt/SolarisStudio12.4-beta_mar14-solaris-x86/bin/CC -std=c++11 test.cpp
"test.cpp", line 8: Error: Cannot use Ternary to initialize integral type.
"test.cpp", line 8: Error: Switch selection expression must be of an integral type.
"test.cpp", line 9: Error: An integer constant expression is required for a case label.
"test.cpp", line 10: Error: An integer constant expression is required for a case label.
"test.cpp", line 11: Error: An integer constant expression is required for a case label.
5 Error(s) detected.

Thanks for reporting this problem! I have filed bug 18499900.
BTW, according to the C++11 standard, the code is actually not valid. Section 6.4.2, switch statement, says an implicit conversion to an integral type is required, which is not the case for for a scoped enum (one using the "class enum" syntax). This limitation was raised in the C++ Committee as an issue to be fixed, and the C++14 standard makes the code valid.
As a workaround, or to make the code conform to C++11, you can add casts to int for the enum variable and the enumerators.
Message was edited by: Steve_Clamage

Extend Provisioning (from OIM to OID) for already provisioned resources

We use OIM 9.1.0 to provision users to several target systems, for example OID. Not all information stored for a user in OIM is also provisioned to OID (for example department or location or phone is only stored in OIM). The provisionig task automatically is created via access policys.
This works fine.
Now we want to provision some more data (including department and location) to OID. So I changed the oid connector configuration to also provision these fields. This works fine for new users (which are not already provisioned to oid).
But we also need these additional fields in OID for users which have already been provisioned in the past. How can this requirement be implemented? Is there a way to resubmit these provisiong tasks oder to automatically update the process form.

Create a schedule task which will read the data from OIM User Profile and update the process form using tcFormInstanceOperationsIntf OIM APIs.
Also create their Label Name updated task in OID Workflow (Process Defintion)

__ Is there a way to adjust the key commands for switching channels in curves?

__ Is there a way to adjust the key commands for switching channels in curves?
By that I mean <command> + 1 for cyan, <command> + 2 for magenta etc. like Photoshop CS3 rather than <option> + 3 for cyan etc.
There's gotta be a way under Edit --> Keyboard Shortcuts - but I can't find it!
Thanks,
Hugh

Hi,
You can find the CS4 plug-in here:
http://blogs.adobe.com/jnack/files/Use_Old_Shortcuts.zip
It's inline in tis post with some more background info:
http://blogs.adobe.com/jnack/2010/05/use_legacy_shortcuts_option_in_cs5.html
regards,
steve

Charged £36 for switching to a different supplier ...

I signed a 12 month phone and broadband contract last September with BT, and received a renewal notice a month prior to my contract being up to say that I should let them know if I didn't want to renew, otherwise my renewal would go ahead on 19th September.
This year I decided to try a different supplier, so I signed up with this other company at the start of September and they contacted BT to say that I would be switching - this notice was given two weeks before 19th September. My switchover date was 26th September, so I had one week further with BT beyond my 12 month contact, which BT didn't state would be a problem. BT sent a letter confirming my account was being terminated, and stating that I would be charged £0.77 for switching. It seemed a bit strange to me that I would be charged for switching suppliers, after all it doesn't cost BT anything apart from losing my custom and I wouldn't have thought it was in line with competition laws to try and put charges in place to discourage people from switching, but I thought nothing of it as it was such a small amount.
However, I've since received an email from them saying:
As you're stopping your service within the minimum term, you'll need to pay £36.170002 for stopping early. This fee is usually based on the number of months left on your contract.
But I'm NOT stopping within the minimum term, my minimum term was 12 months which I completed - and I never signed a new contract with them, and I told them with plenty of notice that I would be switching elsewhere, so there are NO months left on my contract.
I can understand that I will be charged for an extra week of service, which by my calculations for unlimited evening and weekend calls (£3 per month plus £10 line rental) and 40GB monthly broadband (£18 per month) totalling £31 per month, for 7 days that works out at about £7, which is what I would expect my final bill to come to.
Anyone else had this issue? It's odd that I've received two different letters via different communication channels (one in the post and one via email) which say contradictory things about termination charges.
Advice and help would be much appreciated. Previously I had a reasonably good image of BT and would have considered switching back to them next year, however that prospect becomes less likely the more they mess me around with this.
Thanks for any help you can give,
Tdot

Thanks for responding, in answer to your questions:
1. No I didn't get a MAC code from them, I didn't realise I even had one, they didn't mention this when they contacted me and said it would cost 77p to switch. As they didn't mention it in their letter when they had the opportunity to tell me about any additional charges, I'd be very annoyed if they charged me when there was another way of doing it which would exempt me from those charges!
2. My new supplier contacted BT straight away and BT sent a letter to me confirming that my contract would be ending. As a result, I didn't think I'd need to contact them to say it would be ending - surely they already knew if they contacted me to let me know when my service would be stopping?
I did email them and they have got back to me saying something about a fault with my bill, and that everything should be fine once my final bill is issued. I will wait and see on the final bill what happens, then if it's not to my satisfaction I'll put in an official complaint.
From a look around this forum, the MAC code issue seems a common one. Any ideas how it usually pans out? It seems to be an ongoing issue on quite a few posts. Is there anything I can do now the switch has occured? I assume not, but it's worth a try.
Many thanks,
tdot

What is the benefit in using OID for names resolution?

I have been wondering about this for awhile. I have been working on getting this to work in Iplanet along with Pat Lehane ([email protected]), and it works now.
What are the benefits in using OID for names resolution when you can just use the static tnsnames.ora. Database and database names are not created dynamically and they don't change that often. Would creates a new database every day and has to worry about changing the static tnsnames.ora file. In my environment, we run Oracle applications from a server, so there is only one tnsnames.ora file, on the file server.
It would appear that using OID would cause extra traffic (LDAP lookups) on your network.
I would like some opinions from both Oracle and Oracle users. Thanks

hi,
A benefit of using OID for names resolution is that it allows you to centralize net8 naming (i.e., tnsnames) information in the same place (OID) where other types of administrative information (about users, enterprise groups, enterprise roles, etc) gets stored. If you are more comfortable using tnsnames.ora files for net8 naming, that is perfectly fine!
An important reason that Oracle had for providing Net8 naming functionality in OID is that the legacy 'Oracle Names' functionality of Oracle 7 will eventually be desupported. This is discussed in metalink Note #135696.1 on http://metalink.oracle.com .
Hope this helps.

Request for switch off protection in coming new iphone.

Dear apple
Subject- Request for switch off protection in coming new iphone.
I am a very new customer of yours, have bought a iPhone 5s on 25th Dec '13, but unfortunately someone stolen my phone in a MELA in my city. I immediately call my iphone but getting it switch off, as the thief had put the phone in switch off mode. I search it in iCloud with find my iphone apps but getting offline till date. I use pass code & finger print protection that's why probably it can't be use by the thief, but it can be sell as spare parts by opening up its parts . I had do all legal formalities & inform my carrier to lock my sim. Recently I again bought a new iPhone 4s 8GB from amazon.com & using it now.
It is the time to welcoming new iphone probably iphone 6/iphone air in this fall. I have plan to buy it & a apple laptop but first iphone 6 followed by iwatch if you launch & than laptop.
Now coming to the main point why I have written this mail let's explain it - I think you should put a switch off protection in this new device so that someone can't put the phone in switch off mode except the owner, at-least phone can be track till the battery last if someone stollen it. Because I know the problem & pain when someone lose a smart phone with all personal details. So please consider this in your new device as a new feature.
I have given the details of my both phone -
1.iphone 5s Gold
IMEI no
SL no F2******RC6
Parts no MF354HN/A
2. iPhone 4s 8GB black
IMEI no
SL no C8*****ML6
Parts noMF265HN/A
Thanking you
Dr Jyoti Prasad Rajkhowa
Sivsagar
Assam
India
<Edited by Host>

This is a user-to-user forum. If you wish to offer Apple feedback, you can do so here: http://www.apple.com/feedback/
As for your suggestion, as much as I can understand what you are requesting, if the device is turned off, it is off. There isn't anything Apple or your carrier can do about that. Having a device that is OFF continue to send a signal suggest all sorts of privacy and battery management issues.

Problem configuring SOA suite to use OID for authentication

We are in the process of rebuilding our environment to use the full SOA suite with our OID server for authentication (was previously just BPEL using AD directly), and have encountered several problems (below). We have rebuilt the OID server, and reinstalled the SOA suite into a clean ORACLE_HOME to no avail.
We first rebuilt the OID server using the following steps (derived from Oracle® Internet Directory Administrator's Guide):
1)     Create the Import and Export profiles for AD synchronization. We did this using the Directory Integration and Provisioning Server Administration tool under “Active Directory Configuration”
2)     Modify the map file to specify the correct OU mappings between AD and OID.
3)     Update the profile with the new map file using “dipassistant.bat mp”
4)     Bootstrap the import profile using “dipassistant.bat bootstrap”
5)     Start a new instance of the Integration server (odisrv) running on config set 1 (the config set containing the Active Directory import/export profiles) using “oidctl”
6)     Set the Import profile to Enable. The OID server does not export changes to AD in our current configuration, so the Export profile is left on disable (and not bootstrapped)
At this point it appears that the AD synchronizes correctly into our new OID server.
Next we installed the SOA suite:
1)     We ran “irca.bat” on our database server to create the ORABPEL, ORAESB, and ORAWSM schemas and associated integration repository structure.
2)     After launching the SOA suite installer, we selected Advanced Install.
3)     On the next screen, we selected J2EE Server, Web Server, and SOA Suite.
4)     We then provided the credentials for our Oracle database, and the passwords for ORABPEL, ORAESB, and ORAWSM.
5)     We configured our new AS instance as an administration instance, but did not opt to use from a separate HTTP server, and did not make this instance part of an OAS cluster topology.
And finally, we configured our new SOA suite instance to use OID for authentication (using the instructions in Oracle® BPEL Process Manager Administrator's Guide section 2.1.3):
1)     Used the configure_oid.bat command to seed OID with required users only.
2)     Logged into the OracleAS Control Console
3)     Chose the oc4j_soa instance, then Administration->Security->Identity Management
4)     Configured the OID server using a non-ssl connection and the cn=orcladmin account.
5)     When prompted, chose to reconfigure all applications in the oc4j_soa instance to OID, but not to use SSO for any of them.
6)     Copied the contents of ORACLE_HOME\j2ee\home\config\jazn.xml to ORACLE_HOME\j2ee\oc4j_soa\config\jazn.xml
7)     Restarted the application server.
After this procedure, we encountered the following issues:
1)     The BPEL console appears to authenticate users correctly out of OID, but no users have access to the default domain, including bpeladmin and oc4jadmin. All users receive a similar access denied message when attempting to log into the BPEL Admin Console.
2)     We cannot upload a BPEL process to our new server via JDeveloper’s standard BPEL deployment mechanisms. The connection appears to be working properly and passes all tests, but on uploading a process we get a Java AccessDeniedException. ESB appears to be functioning properly, and accepts uploaded projects without issue.

Bassman,
We recently configured our SOA Suite to use OID and SSO. We had the same issues you are having, and we found the resolutions in a blog from Jaas Poot (http://blog.jpoot.com/category/oracle-appserver/oid-ldap/). For the BPEL domain access, this involved going to the data-sources.xml file and changing the database passwords from using ->pwForOrabpel for the orabpel schema and ->pwForOraesb for the oraesb schema to the real passwords; the blog explains more about this.
The blog also covers the JDeveloper deployment issue, and another issue we encountered, where we couldn't access the BPEL Admin console. All of these were resolved following the steps in the blog.
Hope this helps
Candace

Why doesn't the rotate gesture on my trackpad behave as it used to for switching between tabs when it works the same with all other programs besides Firefox?

Why doesn't the rotate gesture on my trackpad behave as it used to for switching between tabs when it works the same with all other programs besides Firefox?
I changed the about:config to make the rotate gesture move between tabs, and it worked great for well over a year. Now it behaves erratically as described here:
https://bugzilla.mozilla.org/show_bug.cgi?id=877598
It used to be very controllable to move one tab over, now it is erratic and moves quickly and to unexpected tabs regardless of how slow I do the rotate gesture. This is the main reason I use Firefox over Chrome and I would like to continue to do so unless there is no fix to this.

Just set the browser.gesture.twist.threshold to something around 15-25.

Device package error for switch Cat2960

Hi,,
We are installing device package for switch Cat2960. But we get below error message when trying to install the same.
WARNING : Cat2960(6.1):Consistency check failed for base package SharedDcmaIOS
When trying to updgrade the SharedDcmaIOS to higher version we get the below error message.
SharedDcmaIOS, SharedNetshowIOS, SharedSwimIOS
WARNING : SharedSwimIOS(2.5.1):Consistency check failed for base package LibSwim
WARNING : SharedNetshowIOS(2.2.1):Major versions are incompatible for base package [SharedNetshowIOS]. Required version = 1.0, Found version = 2.2
Kindly guide us in resolving the above issue related to device pacakage installation.
License Info:
Bundle             Installed/Updated on
LMS2.6            18 Jun 2009
Name      Version      Size         Status        Expiration Date
1.CM         4.0       Unlimited    Purchased      Never
2.DFM       2.0       Unlimited    Purchased      Never
3.IPM        2.6      Unlimited     Purchased      Never
4.RME       4.0      Unlimited     Purchased      Never

Hi,
We are using LMS2.6 and you have provided solution to install / upgrade to LMS 2.5.1
We are installing the device package Cat2960.RME43.v6-1 for switch 2960
Supporting device package we are installing are
SharedSwimIOS.RME43.v2-5-1
SharedDcmaIOS.RME43.v2-4-1
SharedNetshowIOS.RME43.v2-2-1
When installing we get the error Consistency check failed for base package.
Regards,
Rakesh Prasad

OID FOR SWITCH 2530 & 1910

Similar Messages

Maybe you are looking for