OIM after BP12 patch system error and logging not working

Hi,
I am using Weblogic 10.3.2 and need to install OIM. I have installed the 9.1.0.1 and then the patchset to 9.1.0.2. Then I have installed the bundle patch BP07 and everything was ok.
Finally I have installed the BP12: now i am unable to log in the OIM admin panel ( system error ) and i cannot connect with the design console (NullPointerException). The worst part is that OIM does not write a log file anymore, so i can't determine what's wrong. What should i do?
thx in advance

no errors, everything fine. The webapps (xellerate and nexaweb) are started normally.
As an additional information, i just tried to revert to BP07, it still doesn't work.

Similar Messages

System error and restart not possible

Hi
I have developed the Proxy to SOAP scenario and it used to work normally as designed, But suddenly it started giving the System error and restart not possible,
I see the following error in the Runtime work bench on the Receiver CC
SOAP: response message contains an error XIAdapter/HTTP/ADAPTER.HTTP_EXCEPTION - HTTP 500 Internal Server Error
Can anyone let me know what the error is
Thanks
PR

Hii
If this channel was in working state earlier, then this error would mean that the receiver webserver hosting the webservice has some problem. You may contact the receiver system for checking out if they have problem at their end and if they agree resend the messages and it should pass through.
It may be problem with certificates even.
Best Regards

NOKIA N97 SYSTEM ERROR AND MENU NOT OPENING

I have a N97 which is a far cry from the N900. Anyhow, of recent when I try to access the menu a message pops up saying "System error" - so, I cannot access any of the other functions through Menu and, quite honestly, I don't know how else to access the menu. Any ideas or suggestions to resolve this would be appreciated!

Apart from loss of data I would probably suggest carrying out a "hard reset" upon this device, which is chronically short of phone memory:http://mynokiablog.com/2009/07/18/how-to-hard-reset-your-nokia-n97/
Happy to have helped forum in a small way with a Support Ratio = 37.0

Help with After Effects? Null Layer and Text not working?

In after effects cs5.5 on mac, im motion tracking as normal, and the track works fine, then when i add the null layer and edit the tracking target to the null layer, the screen goes black, and all i can see is the null layer as a red box moving along the motion track path (i cant see the path) also, whenever i try to add text, (which im trying to motion track via attatching to the null layer) the text is invisible, when the screens black, all i can see is the wire frame of the text next to the square null layer, im pretty new to after effects, but im following tutorials as i should, and its just not working as it shows in all the videos ive tried, please help!

Check whether you have wireframe mode enabled/ Live Update disabled. Sounds like one of those cases. Other than that this could be OpenGL issues, so turn it off in the prefs. Also check your comp size vs. the size of the footage you are tracking. Tracking works relative to the layer, so if the comp is too small, the values would be so large they end up being outside the comp.
Mylenium

Hp 2000 laptop ctrl+alt+delete disk read error and f11 not working.

Im having a problem. I have HP 2000 laptop and i recently download a antivirus thaeme asked me to resgate the conputer so i disso and i started to get this disk read error saying ctrl+alt+delete to restarem and agente i do it restart and i get the same error again. So i tries f11 to recover the laptop when i press f11 it just shown the hp logo on the middle of the screen and f11 sustém recovery at the bottom left corner and it just stay at that screen and it dosent go antes further. Anyone help?

Hi
Try to run the tests below
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443317
If it passes then call Hp and let them know that the F11 recovery is not working and you would like to get recovery Disks they will send you the OS disks so that you can reinstall the OS back on to your unit.
Hope this helps.
***** Click the KUDOS Thumbs UP (Like) on the left to say 'Thanks'*****
****Make it easier for other people to find solutions, by marking my answer “Accept as Solution”&"Kudos"if it solves your problem.****
-VJ
Although I am an HP Employee, I am speaking for myself and not for HP.

System errors and replys not posting

Over the last couple of days I've had several intermittent problems trying to view threads in this forum, mainly shown as System connection errors. Today I've also tried to post a reply in a thread, the submit appears to work (no error message) but my reply has not been added.
Anyone else seen this and know what's going on?
Cheers
Ian

Over the last couple of days I've had several intermittent problems trying to view threads in this forum, mainly shown as System connection errors. Today I've also tried to post a reply in a thread, the submit appears to work (no error message) but my reply has not been added.
Anyone else seen this and know what's going on?
Cheers
Ian

Screen Flickering Everytime After Updating Synaptics Touchpad Driver And Touchpad Not Working

I have a HP ENVY 4 1023tu Notebook with Windows 8 Pro. I always keep my pc updated. But whenever i try updated the synaptics touchpad driver through availabe updates by hp support assistant, the screen starts to flicker(Start screen and settings bar at the right) and touchpad doesn't work . The external works fine. Then I have to roll back the driver . then it comes to normal. If the driver update is meant to be updated then why its not supporting...

I had the same problem as you with my Hp Probook 450 and I think I found a cause of the problem. I installed Windows 8.1 on it, and when I tried to install touchpad driver, after system restart my screen was blank. My problem is in AMD Radeon graphics card integrated in laptop. When I installed touchpad driver, the graphics driver somehow updated too. The problem is, that AMD only have beta driver for Windows 8.1, while the old one isn't good. So I had to start computer in safe mode and disabled graphics card in Windows device manager. Then I downloaded that beta driver and installed it (still with some small problems) So, the beta driver also isn't perfect, but it will help until they release final version. So I hope that helps you, or anyone, that might have similar problems.

Crashing, disk errors and iPod not working!

For a while now my mac keeps on crashing. It's done so in a variety of ways, the most common being the screen becomes dulled with the message on top saying I need to restart my computer. I also had a weird occassion when the screen went purple/pink and grey and gradually changed and got darker until it eventually switched itself off.
On different occassions I have verified the permissions. Sometimes there are no errors. Often there are errors but with different programs everytime. I always repair these errors.
Yesterday I verified my disk and there was an error. When I went to repair it using my Install disk it said the error could not be repaired.
My iPod does not properly sync with my computer either.
About 2 months ago I had to do an Archive and Install after a lot of my 3rd party programs simply failed to load.
I don't have a clue what to do, so any help would be greatly appreciated. My computer is still within its 1year warranty but I read that if its a software problem they'll charge me for fixing it.
Many Thanks.

Each time I have had to restart my computer I have copied the error report that appears once it is up and running again.
Below is the most recent of those reports:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000011 PC=0x000000000006644C
Latest crash info for cpu 0:
Exception state (sv=0x43900C80)
PC=0x0006644C; MSR=0x00009030; DAR=0x00000011; DSISR=0x40000000; LR=0x000663D8; R1=0x220F3C90; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x220F3CB0 0x000704A8 0x00062584 0x000A845C 0x000AB980
Proceeding back via exception chain:
Exception state (sv=0x43900C80)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x37EEE280)
PC=0x90003768; MSR=0x0200F030; DAR=0x3000000C; DSISR=0x40000000; LR=0x90003510; R1=0xBFFFDF50; XCP=0x0000000C (0x300 - Data access)
Kernel version:
Darwin Kernel Version 8.9.0: Thu Feb 22 20:54:07 PST 2007; root:xnu-792.17.14~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x000952D8 0x000957F0 0x00026898 0x000A8004 0x000AB980
Proceeding back via exception chain:
Exception state (sv=0x43900C80)
PC=0x0006644C; MSR=0x00009030; DAR=0x00000011; DSISR=0x40000000; LR=0x000663D8; R1=0x220F3C90; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x220F3CB0 0x000704A8 0x00062584 0x000A845C 0x000AB980
Exception state (sv=0x37EEE280)
PC=0x90003768; MSR=0x0200F030; DAR=0x3000000C; DSISR=0x40000000; LR=0x90003510; R1=0xBFFFDF50; XCP=0x0000000C (0x300 - Data access)
Kernel version:
Darwin Kernel Version 8.9.0: Thu Feb 22 20:54:07 PST 2007; root:xnu-792.17.14~1/RELEASE_PPCModel: PowerBook6,7, BootROM 4.9.3f0, 1 processors, PowerPC G4 (1.5), 1.42 GHz, 1.5 GB
Graphics: ATI Mobility Radeon 9550, ATY,M12, AGP, 32 MB
Memory Module: DIMM0/BUILT-IN, 512 MB, built-in, built-in
Memory Module: DIMM1/J7, 1 GB, DDR SDRAM, PC2700U-25330
AirPort: AirPort Extreme, 405.1 (3.90.34.0.p18)
Modem: Jump, V.92, Version 1.0
Bluetooth: Version 1.7.14f14, 2 service, 1 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
PCI Card: pci106b,4318, sppci_othernetwork, SLOT-B
Parallel ATA Device: DV-W28SLA
Parallel ATA Device: TOSHIBA MK6025GAS, 55.89 GB
USB Device: iPod, Apple, Up to 480 Mb/sec, 500 mA
USB Device: Bluetooth HCI, Up to 12 Mb/sec, 500 mA
USB Device: Apple Internal Trackpad, Apple Computer, Up to 12 Mb/sec, 500 mA
I hope this helps.
Cheers.

Running Premiere PrO cs6. After upgrading to Yosemite 10.10.2 Adobe Premiere wont run, come up with system error and shuts down. Any one else had this issue?

Running Premiere PrO cs6. After upgrading to Yosemite 10.10.2 Adobe Premiere wont run, come up with system error and shuts down. Any one else had this issue?

can try this Premiere Pro CC, CC 2014, or 2014.1 freezing on startup or crashing while working (Mac OS X 10.9, and later)

Extract abends after sometime without any errors in logs

Hi Folks,
I am implementing unidirectional simple replication for one schema (DDL & DML) without GG data pump and I am newer to GG.
Extract abends after sometime without any errors in logs. I doubt I did not configure exttrail/rmttrail properly.
What should be the commands to configure trails in this scenerio ?
Any suggestions ?
Regards
Edited by: LazyDBA11g on Aug 22, 2012 1:00 AM

Thanks Paddu for reply but I can not use DBLOGREADER as it is not compatible in my env
Use the TRANLOGOPTIONS parameter with the DBLOGREADER option in the Extract parameter file if the ASM instance is one of the following versions:
Oracle 10.2.0.5 or later 10g R2 versions
Oracle 11.2.0.2 or later 11g R2 versionsLastly I dont have connectivity issue with ASM.
Regards
Edited by: LazyDBA11g on Aug 22, 2012 1:03 AM

At startup-system error and divide by zero

I've been having a lot of problems starting up my beige G3 mini tower, it has 233mhz, 384ram, mac os9.1. I've zapped the pram and held the shift key down to boot with extensions off, didnt work. I've changed the battery twice in case the first replacement was bad, it started up and ran long enough for me to trash all the preferences, I tried to change the extensions, but when restarting it was back to not completely starting up. I've tried pressing the button near the pci slots with the battery out, 30 seconds, waited 30 minutes and held down the button for another 30 seconds, replaced the battery, checked the sound card for looseness then at startup it worked till I changed the time and date. I tried the battery and button again this time waiting over night between pressing the button for 30 seconds, after startup I was able to run disc first aid and it said everything was ok, then crashed again when I tried to change the date and time. I've even tried booting up from command/option/o/f, I'm not sure what firmware is but it would try to start up that way,but was very slow with a os cd in the cd drive. I tried to erase the hard drive but I couldnt get it to start up from a cd, iv'e tried os9, the original cd that came with the computer and a system recovery cd.
Most times when trying to start it up it chimes, then the happy mac with a grey screen, then the mac os screen, then the bomb with "system error" and under that "bus error" under that it says to restart with extensions off. sometimes the button for restart will even work with the cursor. Once, after trying to start up after all the battery removal, pressing button near pci slots , pressing com/opt/o/f, extensions off, the screen getting to the mac os then the bomb dialogue, it said system error and instead of saying "bus error" it said "divide by zero". Thats the first and only time I've seen that one. Also, the grey screen (with the happy mac disc icon) now has horizontal lines with texture? that I havent noticed before.
got any ideas what I should do next? I probably wouldnt bother with my G3 anymore because I just bought a new Imac, but I have a vinyl cutter hooked to it, it has the old round serial port cables and I would have to buy new software, cables and dongle to use it with my new Imac, I also have illustrator, photoshop, scanner, and drawing tablet on my G3 that I cant use on my new Imac (intel) leopard.
Is my hard drive or motherboard dying? is there a way to find out if and what hardware is messed up? and if so, is there still still parts out there for this G3?

Hi, R1camper -
I ran disc first aid from the cd and and it said it couldnt fix-overlapped extent allocation,4,479.
That is a type of disk directory damage, one which Disk First Aid can not repair.
Alsoft's DiskWarrior can usually repair that kind of damage, with no loss of files. If you choose to go this route, suggest you call (or email) Alsoft's sales department, and request an older version of DiskWarrior - the current versions won't run on your Beige G3/MT.
However, if you can manage to live with the loss of files, you can probably replace the hard drive for less cost.
Your Beige G3/MT came with either an ATA (now often referred to as PATA and/or IDE) drive or a SCSI drive - it could have been ordered with either when the machine was new.
With luck it will be an ATA drive, since those are the least expensive and the easiest to install. Such drives are not Mac-specific - any ATA drive designed for internal use and of appropriate size will work. The only item of concern is to set the drive's jumpers properly. The drive should be jumpered as Master (it may come preset as Master or as Cable Select - Cable Select will not work on your model), unless it is a Western Digital in which case it should be set to Single if that is an available choice.
There is probably little to gain by getting a 7200RPM drive, especially if there is extra cost for one vs. a 5400RPM drive - the relatively slow internal bus speed on your machine will not be able to take significant advantage of a faster drive.
Re the RAM, if you have the time you might try replacing any you took out. Over time the contact the module makes in its slot can get iffy - removing and replacing the module usually fixes that problem, by wiping the contacts clean.

I recently got a new computer because my old one wouldn't let me open creative suite 3 after it generated a error and now I can't deactivate the key to activate it onto my new account.

I recently got a new computer because my old one wouldn't let me open creative suite 3 after it generated a error and now I can't deactivate the key to activate it onto my new computer. Any help would be appreciated. Thank you.

You are allowed to have two activted installations, so if the first machine is the only machine with an activated installation there is nothing prohibiting you from installing and activating on the new machine.
You can contact Adobe Support thru chat to have the old installation deactivation.
Serial number and activation support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html ( http://adobe.ly/1aYjbSC )

After receiving a Generator error and prompt to restart. I restarted Photoshop and the app disappeared off my computer. How do I get it back. The cloud widget says it is all up to date?

After receiving a Generator error and prompt to restart. I restarted Photoshop and the app disappeared off my computer. How do I get it back. The cloud widget says it is all up to date?

CC desktop lists applications as "Up to Date" when they are not
-http://helpx.adobe.com/creative-cloud/kb/aam-lists-removed-apps-date.html

Application Error, System Error and Error in SXMB_Moni

Dear PI Gurus,
I am kinda new to PI(XI) environment, and my self confused when I try to search failed messages in XI. I saw in Status group, there is Application Error, system Error and Error under SXMB_MONI. And I am wondering what is the different between these errors. Worst to come it all errors, Why we do have this separated errors? Can anyone tell me, what is the difference between this errors?
Thank You
Regards
Ramesh

Hi
- Application Error related to SOAP
just look at tgis Blog
/people/jin.shin/blog/2007/05/21/handling-web-service-soap-fault-responses-in-sap-netweaver-xi
also look at this Thread for SXMB_MONI-system error occured
SXMB_MONI-system error occured during persist
Regards
Abhishek
Edited by: Abhishek Agrahari on Jan 21, 2009 7:48 AM

When I try to connect to iCloud, it says there is a server error and does not log me in. This happens every time. How can I circumvent this server error?

When I try to connect to iCloud, it says there is a server error and does not log me in. This happens every time. How can I circumvent this server error?

Try restarting your computer and your router.
If there is a specific error code, take a look at this article.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694

OIM after BP12 patch system error and logging not working

Similar Messages

Maybe you are looking for