%OIR-SP-6-DOWNGRADE_EARL: Module 4 DFC installed is not identical to system PFC and will perform at current system operating mode

Hi Everyone,
Good day!
We have WS-SUP720-3BXL and WS-F6700-DFC3CXL installed on 7609-S router and based on this link http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/107258-C6K-PFC-DFC-CFC.html the Resultant mode should be PFC3BXL. However, as shown below, the PFC operating mode becomes PFC3B.
Router#sh platform hardware pfc mod
PFC operating mode : PFC3B
Following are the modules installed in our router.
Router#sh mod
Mod Ports Card Type                              Model              Serial No.
4    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      XXXXXXXXX
5    2 Supervisor Engine 720 (Active)         WS-SUP720-3BXL     XXXXXXXXX
6    2 Supervisor Engine 720 (Hot)            WS-SUP720-3BXL     XXXXXXXXX
Mod MAC addresses                       Hw    Fw           Sw           Status
4 001f.6ca4.2588 to 001f.6ca4.258f   2.1   12.2(18r)S1 12.2(33)SRE9 Ok
5 001f.6c77.8448 to 001f.6c77.844b   5.9   8.5(3)       12.2(33)SRE9 Ok
6 001a.a22d.b200 to 001a.a22d.b203   5.10 8.5(3)       12.2(33)SRE9 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
4 Distributed Forwarding Card WS-F6700-DFC3CXL   XXXXXXXXX 1.0    Ok
5 Policy Feature Card 3       WS-F6K-PFC3BXL     XXXXXXXXX 1.11   Ok
5 MSFC3 Daughterboard         WS-SUP720          XXXXXXXXX 4.0    Ok
6 Policy Feature Card 3       WS-F6K-PFC3BXL     XXXXXXXXX 1.11   Ok
6 MSFC3 Daughterboard         WS-SUP720          XXXXXXXXX 4.1    Ok
Mod Online Diag Status
4 Pass
5 Pass
6 Pass
The problem now is that I am seeing the messages below and the maximum value that I can enter for mls cef maximum-routes is 239K only instead of 1M.
%MLSCEF-SP-4-FIB_EXCEPTION_THRESHOLD: Hardware CEF entry usage is at 95% capacity for IPv4 unicast protocol.
Based on this link, http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html WS-SUP720-3BXL and WS-F6700-DFC3CXL has a Default IPv4 TCAM Space of 512K but I'm only getting the following.
Router#sh mls cef max
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS         - 192k (default)
IPv6 + IP Multicast - 32k (default)
Please advise what seems the problem.
Thanks

Was the WS-X6708-10GE inserted some time after the router was last reloaded? Cisco's PFC/DFC FAQ states that mixing different types of PFCs and DFCs affects OIR (online insertion and removal) - i.e. the router needs to be reloaded with the line-card installed in order for that PFC/DFC combination to work as expected (or even to work at all) - and although I couldn't find PFC3BXL+DFC3CXL as an explicit example of such situation, a reload might be worth a shot if the downtime is not too much trouble...

Similar Messages

Photoshop Elements 13: The product you are trying to install is not an Adobe Genuine Software and appears to be counterfeit.

Installed Photoshop Elements 13 on old computer in December, old computer crashed this week so had to purchase new computer. Attempted to install and received the following error message: The product you are trying to install is not an Adobe Genuine Software and appears to be counterfeit. What now???

Try Warning: "Adobe Genuine Software Validation Failure..." | Windows

I have the newest version of the mac book pro and i recently bought iLife 11 because i needed idvd but when i installed iLife my iphoto no longer works and will not let me open. How do i fix this

I have the newest version of the mac book pro and i recently bought iLife 11 because i needed idvd but when i installed iLife my iphoto no longer works and will not let me open. How do i fix this

Welcome to Apple Support Communities
iTunes in Mac OS X Tiger is outdated. Open  > Software Update to install the latest iTunes version for Tiger.
If you need iTunes 10.7 or a newer version, you have to upgrade to Mac OS X Snow Leopard. First, check that your Mac is supported > http://support.apple.com/kb/sp575 If it is, buy Snow Leopard > http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
After buying Snow Leopard, make a backup of your data, insert the DVD and upgrade to Snow Leopard. After upgrading, open  > Software Update, and install the latest Snow Leopard version. Finally, run Software Update again to install iTunes 11.0.4. If you want to install iTunes 10.7 instead, download it from the Apple website > http://support.apple.com/kb/dl1576

HT4623 iphone 4 I am trying to install iOS6.0.1 the install is stuck in "preparing to update" and will not move forward. How do I stop the install.

I am trying to install iOS6.0.1 on my iphone4 and it is stuck on "preparing to install" How do I stop the instal?????

I'm not sure iCloud is the best community to post that question in, to be honest I have the feeling it's likely something best asked from any M$ discussion groups that there might be.

CC will not work-uninstsll run cleaner and will not install

W7 CC will not work or update. Uninstall from control panel. Run CC cleaner app. turn off antivirus. try installing- still will not install.

Please follow the steps in :
Error code 50
https://forums.adobe.com/message/6801531
This error code is common, please let us know if it worked
Regards
Rajshree

Error on install, CDROM not booting Kernel, unable to mount CDRM, what now?

Please help. I am new to this, so as many options as possible would be a help.
So far here are the steps I've taken to install Solaris 8 (Intel):
1. Checked HCL - I have two CD ROM's I've tried, both are on the list. (Mitsumi FX140S and Sony DVD DDU220E)
2. Set BIOS to boot CDROM - Boot failure..., I have set and changed jumpers back and forth from Master to Slave. I have moved CDROM drive from primary Slave to secondary Master and secondary Slave.
3. I have downloaded and used the Device Config Assistant boot floppy. It boots and checks devices. It also recognizes the CDROMs I have (both CDROMs are not have installed at the same time).
4. I have selected whichever CDROM I have installed as the default boot device (*) using F4_Boot Tasks. I have also adjusted timeouts from 0,1,2 and 3 seconds and have had autoboot ON/OFF.
5. I have entered F2 to continue and I receive this error:
Unable to mount a Solaris root file system from the device:
CD : (*) Target 1, MITSUMI CD-ROM FX140S !B e12 on Bus Mastering IDE controller on Board PCI bus 0, at Dev 4, Func 1
Error message from mount:
/pci@0,0/pci-ide@4,1/ide@0/sd@1,0:a: can't open - no hsfs VTOC
Press Enter to Continue.
I have inserted all 3 CD I have created with the same results from each. The CDs have the .iso extention and were created using Easy CD Creator.
Please, Please, Please, ANY suggestions!!
LL

First off you don't need to set your CDROM as the default boot device to install Solaris, that's why we have the Solaris DCA boot diskette. And also only the Solaris Installation CD and Software 1 of 2 are bootable CDs, the software 2 of 2 is NOT.
Once you finish downloading the images from Sun's website you need to not only add the .iso extension to the ending of each image file but use the option "Burn using CD image" under the File menu in Easy CD creator.
If you try and view the burned CD under Windows you will only see a small number of the actual files that are on the CD. And NO you will not see the .vtoc file and will not be able make one yourself.
My suggestion would be to try and burn a new CD with the above instructions and boot with the Solaris DCA and continue pressing F2 until you get to the point where it asks you select where you want to boot the kernel from. At that point put with ther Installation CD or Software 1 of 2 in your drive and attempt to boot from it.
Keep us updated on your progress.
Allen
Sun Develeper Technical Support

Trying to install new upgrade to my iphone4 and it put my phone in recovery mode. How do I get it out?

Trying to install new upgrade to my iphone 4 and it put the phone in recovery mode. How do I get it out?

i have this problem too! have you fixed yours yet?

"Product you are trying to install is not genuine" - Adobe Application Manager error message.

Trying to launch the AAM and getting the error message that says "Adobe Genuine Software Validation Failure. The product you are trying to install is not an Adobe Genuine Software and appears to be counterfeit".
I've been subscribed to the creative cloud for four months, never had any trouble before, I'm not trying to download anything and nothing on this computer is counterfeit.
Any help?

Hello,
This behavior is due to a known issue (details at http://blogs.adobe.com/psirt/2012/09/security-advisory-adobe-to-revoke-code-signing-certif icate-apsa12-01-2.html). Fortunately, the solution is simple.
You need to download the latest version of Adobe Application Manager from http://www.adobe.com/support/downloads/detail.jsp?ftpID=4773. After you install it, the error will go away.
Regards,
Amit

How to check module abbreviations and whether they are installed or not ?

Hi All -
There was a question raised , that is self service parts planning module available/installed/registered in our current EBS or not ? How to check whether self service parts planning module is installed or available or not ?
Also i would like to check all the modules which are currently installed and can be used ?
Regards,

Our question says , we do not know the code for Self Service Parts Planning Module . How to check particularly these product is installed or not ?
from the link given , it describes that for self service parts planning code is "SPP" . Can you please confirm ?It is part of "Advanced Supply Chain Planning (ASCP)", so run the query in (How to Find Out Product Installation Information in Oracle Applications? [ID 1275690.1]) and pass the module name.
Similary can we get the product codes for all shared products, installed products and non-installed products. The doc referenced above in this reply will list all the module names, with the product codes and the status.
What does shared products actually mean ?Patching Shared Oracle E-Business Suite Products [ID 1069099.1]
Thanks,
Hussein

Acpi common module won't install

i am trying to help a friend who bought a repaired m35-s456 toshiba laptop. it is a repaired computer with XP sp1 installed. the repairman initially installed the os and gave him a installation disk for a dell. i am not sure if this is a problem with microsoft because it will activate with the origional key code.
the problem i am having is, first, attempting to install the toshiba drivers from the download page, from what i understand, the module acpi common modules must be installed first and then the other applicable modules. but the common module will not install. just get a cursor busy sign for a few seconds and then nothing. could it be caused from a dell file or a toshiba problem.
have reinstalled XP many times and downloaded and installed windows updates both before and after attempting to install the toshiba modules, but every time on reboot a problem occurs where XP will not load and comes up with an error message: system32/hal.dll missing.
i tried to order the origional install disk but toshiba says the computer is too old and not available.
any advise would be appreciated. have found most programs will not install or run on sp1!
Solved!
Go to Solution.

Satellite M35-S456
Your best bet is to order recovery discs from a third party.
   Digitalmedia-labs.com
   MyRecoveryCDs.com
   RestoreDisks.com
   RestoreCD4u
-Jerry

Bridge CC Output Module fix works on WIN7, not on MAC OS X

I have CC installed on a WIN desktop and a MacBookAir. Everything is up-to-date. The are no old Adobe versions installed.
I installed the recent 'fix' on the desktop and it works fine.
On the MBA, there is no folder as named in the Adobe instructions (Mac OS: /Library/Application Support/Adobe/Bridge CC Extensions).
There is no "Extensions" folder, just the Mac OS: /Library/Application Support/Adobe/Bridge CC. This is where I copied the file and folder. The 'OUTPUT' module appears as a selection in Bridge, but does not appear when selected.
I have tried the sugested trouble shooting fixes, to no avail. I have searched and read the other threads on this subject on the forums.
Is there anyone who has made this fix work on OS X and can help me correct this?

On the MBA, there is no folder as named in the Adobe instructions (Mac OS: /Library/Application Support/Adobe/Bridge CC Extensions).
To me this seems to indicate you are looking in the wrong library.
The give path for install needs to be done in the library from your system itself: MacBookAir (or the name you gave it) / Macintosh HD (or the custom name you gave to your start up disk) and then library / App sup / Adobe/ Bridge CC Extensions
I believe you are trying to install in the user library and there is only a BridgeCC folder

Cannot install iTunes 10.7 on Windows 7. Getting "a program required for this install could not be run"--Apple Software Update is not installed, so updating it is not a possible solution.

I was following the process of unistalling all Apple software and reinstalling iTunes. But I am getting an error that says "a program required for this install could not be run."
Other threads recommend updating the Apple Software Update module, but that was uninstalled. So if it's part of the problem, updating it is not a solution.
Windows 7, 64-bit, SP 1 installed.

For what it's worth, at the point the installation fails, Bonjour, Apple Application Support, and Apple Mobile Device Support all show as installed on Control Panel. Apple Software Update has a link on the Start Menu but does NOT show as installed on Control Panel. Is there a way to install this separately from iTunes?

HT1926 Have you gotten the error "a program required for this install could not be run"

Whenever I try to install iTunes on my Windows 7 PC, I get the error" a program required for this install could not be run". Any ideas?

Burwood, that tip says to repair the Apple Software Update module. I went through the process of uninstalling all Apple programs from my computer first, so that's not the problem (and it's not installed, so it can't be repaired).
I tried installing iTunes with the "automatically update" box unchecked as well, to no avail. Any ideas?

I can't open any of my Word documents on my Apple Mac. The error code is EXC_CRASH (SIGABRT) and the blame module name is WordArt. The documents are still there, and I can open them on my iPad when I email them there. Any ideas?

I can't open any of my Word documents on my Apple Mac. The error code is EXC_CRASH (SIGABRT) and the blame module name is WordArt. The documents are still there, and I can open them on my iPad when I email them there. Any ideas?

Uhhhhh... Thank GOD... Got all of my files.
Spent some time on the phone with Apple Care... who was great to deal with but actually... not as helpful as I was hoping. It was suggested that I try DiskWarrior 4 to try to recover the files. $108 later, I had no files.
More calls with Apple Care and they were pretty sure that everything was gone since once the External drive was installed, like a moron, I let TimeMachine go ahead and back up my new MacBook... so it overwrote who knows how many gig that was my entire MacBook.
I wasn't giving up so I called Maxtor, the manufacturer of the external drive itself. They suggested file recovery software from I365... which is also a Seagate company (the makers of the drive). The suggested I simply use their demo because the demo version would find the files. If it found them, I could buy the software to restore them.
It found them! Another $129 after and I was able to restore all of them back to my old PC laptop.
NOW, I just need to figure out how to get the 50gig of HD video files off of my old laptop now and into my Mac and IMovie so I can actually make some DVDs out of them!
I get that Macs and PCs are different formats but I think it is ridiculous that formatting still means basically just wiping out or at least treating massive lots of old data as if it isn't there. There's gotta be a better way to do that.

CS6 photoshop message 'could not load the fast core routines module because the file was not found'

my CS6 photoshop is giving me the message 'could not load the fast core routines module because the file was not found'. this started happening after i used a trial of photoshop CC and decided not to stay with it. my photoshop is part of my CS6 suite and i am only getting this message with photoshop, my ilustrator keeps working just fine..... does anyone know how to fix it? thanks.

I did a search on my system and found the Photoshop has a fastcore plug-in. Creative Cloud includes a subscription version of CS6 version 13.1.2. I do not know if you installed that or not. The cc un-install may have done something. You may need to use Adobe Cleaner then Install The Perpetual CS6 version of Photoshop CS6 version 13.0.6 Mac or Photoshop CS6 version 13.0.1.3 PC and not the subscription CS6 extended version 13.1.2. Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6 If you need to download the CS6 installer Download CS6 products.
You may also be able to recover your cs6 using an old system backup
fastcore.8bx on my system...

%OIR-SP-6-DOWNGRADE_EARL: Module 4 DFC installed is not identical to system PFC and will perform at current system operating mode

Similar Messages

Maybe you are looking for