OK to connect a Mac to Time Capsule simultaneously by wifi and cable?

I just added macbook to my airport network hosted by a time capsule. Next, I want to run an initial time machine backup of macbook onto the time capsule via an ethernet connection.
Should I shut off airport on the macbook before wiring it to the time capsule? Or can the software happily handle two simultaneous connections between newmac the time capsule, one wireless, the other wired? If so, is Time Machine smart enough to realize that it should use the faster wired connection?
Thanks!
Tom
Message was edited by: tttny

Shortly after posting this question I realized that it should have been posted in the Airport>Time Capsule forum. I've repeated the question in that forum and request that replies be posted there. http://discussions.apple.com/thread.jspa?threadID=2489542&tstart=0

Similar Messages

Connecting two macs to time capsule 1.ethernet 2.wirelessly??

Hello All,
I am trying to solve a problem that I have already raised in a previous thread, but which got unnecessarily complicated. So here is the distilled version.
1. I have a a time capsule connected to my mac via ethernet, so essentially I am using it as a hard drive for backing up only. I want to maintain this connection as this imac is my main concern and for speedier back-ups are my priority.
2. I have a a second mac which I would to access time capsule wirelessly.
3. I already have a wireless network offered by an adsl modem/router.
Even though I would have thought it would be easy to have time capsule accessible to both imacs (one via ethernet and the other via the wireless network) I cannot actually achieve this. When I set up through Airport's assistant, establishing the ethernet link with the first imac results in the wireless mode being disabled and the second imac unable to see time capsule.
Any suggestions would be most welcome.
Many thanks.

Well when I investigate through Airport utility it reports that the internet connection is 'off: bridge mode', so I assume that it defaults to that when connecting through ethernet. However it also states that wireless mode is off, so presumably I need this mode on without interrupting the ethernet connection.
Also apologies for the typing errors in the original post. My grammar isn't that bad really.

How to setup Time Capsule to use wifi and 2 ethernet ports

Hi, I hope someone can help with this issue as I've been searching for an answer without success. Basically, can a Time Capsule (1st gen) connected to a modem create a wireless network, as well as connect to an ethernet powerline adapter, as well as connect to an iMac by ethernet?
My original setup was as follows:
modem > time capsule (which creates a wireless network) > iMac
I bought an AirPort Express to use in another room. It was extending the TC wifi network, but the speeds weren't great so I've got a pair of powerline ethernet adapters. I wanted to add those into my current setup so that the Express can create a wireless network.
Anyway, before I can get to that stage, I'm having issues with the TC. I want to achieve the setup as follows:
modem > time capsule (which creates a wireless network) > powerline adapter 1 * > powerline adapter 2 > airport express
* But as well as connecting an ethernet cable to powerline adapter 1, also connect one from TC to my iMac.
When I tried connecting an ethernet cable to the TC in my original setup, the iMac lost connection to the internet. I've managed to get the following setup to work:
modem > time capsule (which creates a wireless network) > powerline adapter 1 > powerline adapter 2 > imac
But to achieve the setup I want, would require me to buy another powerline adapter (for the Express), and it seems silly to have to use a powerline adapter for my iMac when it is right next to the TC.
Any help would be appreciated.

modem > time capsule (which creates a wireless network) > powerline adapter 1 * > powerline adapter 2 > airport express
* But as well as connecting an ethernet cable to powerline adapter 1, also connect one from TC to my iMac.
When I tried connecting an ethernet cable to the TC in my original setup, the iMac lost connection to the internet. I've managed to get the following setup to work:
What you are attempting should work fine. The TC should be able to manage multiple ethernet connections as well as the wireless.
Investigate what is happening when you plug ethernet into the TC from the imac.
Please try it.. turn off wireless in the imac to ensure ethernet is the only connection.
But I would recommend you shut off the whole network at that point. Restart everything in order.. modem .. TC.. EOPs.. Express.. clients.. with 2min gap between them.
Now look at the imac and check the network preferences.. did it pick up the correct IP from the TC? It should have router (gateway) and DNS all correct using dhcp.. if not check the connectivity light on the TC.. does it come on when you plug in the ethernet cord?
Open a terminal on the mac and ping the TC address. does it respond?
Give a few screen shots of how the TC is setup.. bridge, router and what IP it is running. Even just the summary page.

I install LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it. But the popup keeps on coming with the old name.

I installed LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it with less than 7 karakters. But the popup keeps on coming with the old name.

I have a BT Infinity router plugged into the Time Capsule, not sure where the radio settings are?
They are able to use the network settings of the TC i.e. they can connect to the internet via the wifi through the TC but when they try and connect to the AirPort Disk this is where it is not allowing a connection.
I don;t have the drive shared out at all at the moment, is this necessary? How do I do this if so?
I have attached the screen shots of all the settings.
Thanks again for your help.

Remote Connection using Back to my Mac for Time Capsule?

How do I connect to my Time Capsule and connected usb drive/printer now that Back to my Mac for Mobile Me is disabled and iCloud is running Back to my Mac?
More information:
I used to use the Mobile Me's version of Back to my Mac to enable connecting with my time Capsule, but how is this done now that iCloud has taken over Back to my Mac and I have upgraded to Lion.
I have a Feb2011 MBP and a 2010 minimac the macmini is always connected to the time capsule, but I would like to be able to connect directly to the time capsule without having to go through the macmini.
Thank you for your help

It is possible but I am not sure it is worth the hassle..
Your key issue here is public IP for your network.. if you have a static ip you are fine.. but very few people have this. It also depends on how the TC is setup.. is it the main router for the network or plugged into a modem router which has the role of main router, even if you use the TC as a secondary router.
Without more info..
1. This is easy if you have a static public IP and the TC is the main router and gets the public IP on the wan port.. just go to disk sharing in the airport utility manual setup and check for wan (internet access).
2. If you have a dynamic IP, then you will have to sort out how you are going to find that IP.. the normal method to use dyndns account is not directly applicable because the TC has no client. It is possible to set up dyn dns but you will need to purchase your own domain name.
3. You may find it easier to use standard router and bridge the TC. A standard router can be setup to port forward 548 AFP files service to the TC ip address. You may or maynot be able to access the printer. Certainly would be easier if the printer has IPP services. And is a true network printer.
4. Use vpn.. get a vpn router so you can setup proper vpn endpoints.. then you use VPN service to access your local network.. this is far more secure and will work with dyndns just fine.

I have been given a second hand mac pro that does not have a wifi card in it. my router is down stairs so can not connect the mac pro direct into the router can i use my time capsule which uses wifi to my router to connect to the internet?

I ha

If you have a non-Apple "main" router, then "join" would have been the only way it could connect.
Unfortunately, the Time Capsule does not provide any routing functions in this type of setup, so the Ethernet ports are not enabled in this setting.
If you have an Apple "main" router, it may be possible to enable the Ethernet ports in another type of setting. Then you could connect the old Mac to one of the Ethernet ports on the Time Capsule for Internet access.

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

I want to transfer files from a Win XP PC to a Mac using Time Capsule via Ethernet connection. Is this possible?

Sure.. the PC connects by SMB.. the Mac connects by AFP or SMB..
But you can simply share SMB directly from the Mac.. there is no need to copy files through the TC. Go to system preference, sharing, and turn on SMB for the folder you want to share files to / from on the Mac.
Make sure you have a common username and password also helps.
If you have a TC already can you copy files to it via the windows machine??

How can i extend this wifi connection by using 3TB time capsule? I have a mac book pro i7

Hi, i have a wifi in my house connected to an adsl wifi modem with fibernet speed. I just bought a time capsule with 3 TB and installed it at home. However during the first installation i couldn't connect TC to my modem with ethernet cable due to the absence of the cable.
I would like ask if i can extend the wifi range of my network by connecting my TC to my modem without a cable after the first installation with cable is done?
If yes,
Could you please explain how to do it?
Thanks in advance.

No, there is no modem in the TC.. you must continue to use the existing modem.
That can be bridged if your ISP allows it, and use PPPoE client on the TC. It is then the main router of the network.
Sometimes that setup is not possible.. the ISP supplied modem will not bridge or the ISP doesn't use PPPoE as there are a number of different methods to connect.. but the TC only supports that one.
Otherwise just plug the TC into the existing modem router and use it in router bridge mode.. this is the simplest setup and easy to do.
Create a wireless network and you can then use the TC instead of the main router for wireless if you like.

Is it possible to set up Time Capsule on one network and then access its stored data (movies) using Back to My Mac from another network that also has Apple TV to play them?

I recently purchased a Time Capsule to store data at my office. I have an Apple TV at my home that I would like to start using to play my movies. With the storage of the new Time Capsule, I am curious if I can somehow store my iTunes movies on the Time Capsule at my office and then use Back to My Mac to access the TC from my home and then play them via Apple TV. Does this sound possible? We have an iMac at the office that remains on 24/7 connected to the TC.

ATV cannot play movies from the TC, even if it is on your home network.. ATV is a streamer.. it is not a media player.. and the TC is a dumb as a board hard disk in a router.. so it has nothing in it either.
You cannot play movies from ATV without itunes, which streams to the ATV.
If the iMac is running 24/7 then you should be able to connect to the iMac remotely and run from iTunes on that, which could then play movies stored on the TC.. with the following issues.. if you use wireless on the iMac forget it. The iMac has to be ethernet connected as it has to pick up the movie on the library and play it back to the TC to network to your home.
The next issues is speed of slowest connection.
Your download to your home maybe great.. what is the upload speed from your office like??
If you pay for uploads and downloads you will pay for the movie 3x.. first to download it.. second to upload it.. office to net.. and third to download it again.. net to home.. Sorry but it is better to play the movie directly from online itunes store.
If you plan to try and play non-itunes movies over the connection, it won't work.. ATV as stated is linked to itunes and cannot play movie files.
Overall this sounds like you need to think it out a bit more.

Connecting 2 computers thru Time Capsule without Internet?

I had started a question in another area (Mountain Lion) because I am trying desperately to migrate a Windows PC running Windows 7 to a new iMac. The Migration assistant on both computers does not find any computers. The Apple Care people say I am doing everything right, but now some people online are saying that I can't do this wirelessly thru Time Capsule (which we have and is the router for our office which the PC is connected to wirelessly).
The new Mac is in set up beginning mode (meaning it has not been set up wirelessly or anything yet), because on launch it offers to move the data from the PC to set up the new Mac. It is stuck "looking for a computer"
Here is the whole discussion:
https://discussions.apple.com/message/23377824#23377824
Today I went by an Apple store to ask their opinion and the guy told me that I can't connect the 2 computers via ethernet (even though that is what the Migration insturctions say to do), but he said that I shoud be able to connect each computer via ethernet to the Time Capsule and have them recognize each other.
Does this sound right to any of you???
The PC is clear across the room and no where near the internet line, so I would either have to buy a REALLY long ethernet cable to drag over to it, or take the whole computer apart to try and get it near the TC. The mac of course is no problem to move.
I just don't want to do all this if this will not really act as a network (I guess as a server of sorts).
I am confused as the TC manual says that it can be used without internet, but I don't seehow (I've tried rebooting it without a connection). I do not know why the internet is involved at all since what we need is the TC to act as a wireless router (which it is) and do not need to involve the internet at all to link the 2 computers.
I am just totally frustrated that these computers should just communicate wirelessly and/or with each other somehow and do not seem to, as Apple says they should. I know this will turn out to be something really simple and dumb and I'm just not seeing it.
Is it not possible to take the TC and reboot it with the 2 computers connected to it and create a network using the TC as a server or router without needing any internet just so I can get this stuff from the PC migrated (and then never have to deal with it again!!!!)
Any help is greatly appreciated.
Thanks!

I think where the confusion lies is that this is a brand new Mac and NEVER been set up. We are trying to Migrate from the Windows on initial setup - which is what the Mac asks you when you first start it: Language, Keyboard (english) and then if you are setting a New Mac or wanting to tranfer your info to set up from another Mac or from a PC. You choose PC and the MA automatically looks for the other PC. The Windows MA does the same thing. You launch it on the PC and it looks for the Mac to connect to.
They are not "finding" each other - even when connected directly via the ethernet cable to each other as dictated by the MA instructions (see the link you provided and click:
Transferring with the Setup Assistant that appears when your Mac starts up for the first time
This is what I am doing. This is what 2 different guys from Apple Care also said was correct.
They do not communicate. This is why some in the ML discussion area are telling me I can't do this with an ethernet cable even though these are the instructions. They are telling me to use the TC as a router between them.
The PC is already wirelessly connected to the TC but when I connect the Mac to the TC it still does nothing (because I assume it hasn't been "set up" yet to the wireless network).
I did not want to set up the Mac initially on its own because then you create a User and Password and when you migrate it creates a second User and will not migrate into the initial one you set up, ergo you forever are stuck with 2 users on login and 2 sets of stuff taking up space in your Mac.
It should do this on start up. I have NO doubt this is a PC issue, even though I disabled everything I could possibly see to do on it (this is why I need the PC geek in the UK to make sure). The Apple techs have told me some people have to disable and reboot this stuff several times (ARGH!) LOL!
Anyway I did wonder when I tried yesterday to simply take TC off the internet connection and set it up on its own, I could never get it to stop looking for internet (I rebooted it and reinstalled it with a new name and password), but when you look at it in Airport Utility (I'm using a Macbook for the set up), you see it still blinking looking for internet.
I could not find any instructions for someone to use the TC as a router only or as a server, even though you can see there are more choices in the AU setup tabs. The one guy at the Apple store (not Apple Care) said that if I connected the 2 computers to the TC it would act as a router and they could "see" each other for me to setup - but this did not work, hence I came here.
Hope I'm making sense! Thanks so much for your help.

Mac Formatted Time Capsule w/ PC Formatted External Drive Via USB?

I use a Mac-formatted Time Capsule to run Time Machine backups on my MacBook Pro. My wife backs up her PC laptop on a PC-formatted Western Digital "My Book" hard drive which is powered via A/C wall adapter. I connected the Western Digital PC drive to the Time Capsule via USB so it would be available on our home network and my wife could run her PC backups wirelessly, BUT the drive is not showing up on our network. Anybody have any idea what I'm doing wrong?
Thanks in advance!
---Tim

My questions continue below in red. Thank you for your patience.
LaPastenague wrote:
Tsac77 wrote:
Thanks for the in depth clarification. A few follow up questions:
1) Are you saying that even though I am only using the TC (in this instance) to make the windows drive available on the network, the drive still needs to be formatted in HFS+?
HFS+ or FAT32.. the later having severe issues with large disk and large files.
Great. I'll do HFS+
2) If I format the windows drive in HFS+, will the windows laptop be immediately able to write/read to it over the network? Or will I have to install some sort of program on the windows laptop that allows windows to read/write to HFS+ (which I've always undewrstood to be a mac only format)?
The format of the disk connected to a NAS is totally irrelevant.. if it offers windows networking file protocol.. ie SMB then it can store files on the hard disk.. it is just like sharing the disk in the Mac.. you can write to that directly from the PC. Try it.. The disk is controlled by the Mac. But it presents SMB to the Network.. On your Mac, go to system preferences.. sharing.. it should be in Internet and wireless.. but on Lion I have no idea. Open file sharing which should be ticked..there should be a public folder by default.. you can add others.. go to options, turn on SMB.. then from the windows computer you should see the disk available in networking. If not fix the names to SMB standard.. you will need to do this on the TC as well.. short, no spaces.. pure alphanumeric names. Copy some files from windows to your Mac.. you have now copied to a network drive.. with the drive format totally irrelevant to your windows computer.
I'm sorry, but I don't know what "windows networking file protocol" and "SMB" mean. Also, when you say "NAS" are you referring to the Time Capsule or another device? Can you please explain things like "The disk is controlled by the Mac but it presents SMB to the network" in a less advanced way. Pretend I'm a child. You won't be far off. It seems like this technique you're explaining is a way for the windows PC to write to the external drive via my MacBook. Is that even close to correct? The setup I must create needs to work regardless if macbook is on/off/out of the house.
3) Does plugging a USB drive into the TC never work properly or is this just a semi-common problem that happens sometimes? My odds of success will probably dictate whether I try this or not. I already own the windows USB drive and would like to avoid buying more hardware if possible.
It is problematic enough that I recommend you try it before committing to it. Even if you have to copy the files off to another location and then reformat the drive. Test it for a couple of days.. the issue happens especially when you are using Lion.. but will also happen with windows. Especially when the disk spins down it will not spin up again and become available to the network.
Got it.
4) What do you mean by files being in "native format"? And what does a dead TC have to do with whether or not they can be recovered to the windows laptop? If the TC dies, can't I just plug the windows USB drive directly into the windows laptop and it will be the same thing as connecting the drive and laptop via network? How does a dead TC make things more difficult?
Thanks for your continued help.
HFS+ is not windows native format... so files stored by the TC on the USB drive.. when the TC dies.. they all die eventually may be difficult to recover unless you plug it into another TC.. as the PC cannot natively read them. If you format FAT32 then the windows computer can read it.. just there are other issues. eg the disk can be slow.. very slow and it has far less protection. eg a power failure can corrupt the drive.. this was an issue before we moved in windows to NTFS.
Why do you say "files stored BY THE TC on the USB drive" Why is the TC storing files on the USB drive? Isn't plugging the USB into the TC just making the USB available on the network to my windows laptop? Why is the TC storing files?

How to use time capsule as hard drive and connect with existing net gear router

I have a netgear D6300 router, which i use to connect to internet - which is excellent so far for my downloads and games etc for my PS4 and hence am keen to continue using it. I bought the Airport time capsule for wireless storage, and when i set it up, I was advised on setup to connect the TC to my router, and it did what it needed to do.
Now, in order to connect to internet, i need to connect wifi to net gear router, but to access time capsule, i need to change wifi connection to my newly created wifi network with TC.
I want to use TC as a backup storage for my mac (its a 3TB TC), but also, my laptop has only 500gb hard drive which is now half full from downloads, so i want to transfer all my downloads to my TC and use it as an external hard drive, and future downloads to TC - but when i connect to wifi of TC, i can copy my folder on my mac, but not paste it to TC in finder. (the only thing in TC is an image of tmg of my macbook from first backup.).
How do i use TC as an external HD - there wasn't much difference in price of external wifi/wireless HD between non-TC and TC at 3gb, so i just thought i'd go for the airport TC option.
And is it possible to keep connected to wifi internet via net gear router, AND wifi TC - the whole point i bought it (from US shipped to australia on eBay, therefore not able to send back) was to use TC as external large HD via wifi, but keep my net gear router going.
Surely there is a way to not having to flick between wifi connections of TC and net gear internet.
When i'm connected to TC, i can't access internet, only TC.
And I don't really want to connect TC to my router via ethernet cable, as too many cables.
This can't be a difficult situation to manage, but i'm not sure how to do it.
Thanks

And I don't really want to connect TC to my router via ethernet cable, as too many cables.
Sorry but you have very little choice.
The TC can join to a wireless network.. but it is flakey, poor, slow and highly NOT recommended way to do things.
Nevertheless if you want to give it a try .. here is the method.
How do I setup my time capsule with wireless internet?
You SHOULD, plug the TC into the Netgear and run it in bridge mode.. you set the wireless to create a wireless network.. then when you connect to the TC it will be also connected to the internet and fast.
(if you don't do that you may as well have used a USB drive plugged into the Netgear, as it would be just as good).
TC is not actually designed for mixing Time Machine backups and files.. but if you are just storing downloads that is ok.. but I strongly recommend you use a DMG or sparsebundle to prevent the TM and the data from messing each other.
See Pondini instructions here.
Q http://pondini.org/TM/Time_Capsule.html

I can't connect my WD to time capsule

hello, i've a problem, my WD "my book for Mac" don't connect to time capsule usb port.
When i try to connect to time capsule, airport app tell me the following: Must repair the disk.
How i can connect my WD to time capsule??
Best regards.
Pedro Pino

What TC model and firmware is it?
WD mybook are generally ok.. but the unpowered type will have problems.. you need a powered hub.
And some of the older TC will not handle all versions of some products.. WD keep changing them around.
It is often hard to figure out what works and what doesn't.
I am trying to assemble a database here.
USB drive compatibility with Airport Routers. Help make database.

Connected my printer to time capsule how do i get it to work on my computer

i am trying to connect my printer so that everyone can print to it. i connected it to the time capsule, hoew do i get my mac to recongize it

We don't know.....and you do not indicate.....whether your printer connects to the Time Capsule......
Using wireless?
Using Ethernet?
Using USB?
Would be helpful as well if you could provide the make and model number of the printer.

How to connect over internet to time capsule from iphone?

I want to connect to my time capsule 2013 over the internet with an iphone 5, my time capsule is now set in bridge mode and main router is an airport express. How to set to connect in this case and what is a global hostname? In the past i have time capsule as primary router and it was ok to access with file browser, but now i can't connect only in the local wi-fi. Sorry about bad english.

You will have multiple issues here.
It would be much better for the TC to be the main router. Do you have to use express as the main router?? It is underpowered and does not even have disk access.
Remote access is also super difficult from an iphone.. it is not a Mac.. apple designed remote access for Macs.
https://discussions.apple.com/docs/DOC-3413
You can use filebrowser method.
http://www.stratospherix.com/support/gsw_timecapsule.php?page=6remote
Only you need to use the LAN IP of the TC instead of the LAN IP of the express.
Global domain name.. might still work or might not.. apple is working hard to avoid it..
The best option is to buy a static IP from your ISP. That simplifies this whole setup.
Another option not listed is to replace the Express with a proper vpn router. iphone has vpn client built in.. but apple did not include a vpn in their routers. VPN is a lot safer and standard routers use standard dyndns.

OK to connect a Mac to Time Capsule simultaneously by wifi and cable?

Similar Messages

Maybe you are looking for