Old hard drive broke, Macbook will not recognize new hard drive

Hi,
My Macbook wouldn't boot, hard drive was making an odd sound, only would go to the gray/blue screen with the flashing ? folder. I bought a new hard drive and installed it, used Leopard DVD to boot, went to Disk Utility and the only thing that showed up was the DVD. I tried re-seating the drive and still nothing.
Any Suggestions?

Hey hauebj01 and welcome to the forum -
I know it's a hassle but I've heard of some folks having quite a bit of trouble seating replacement drives. You might try that again. Sometimes you have to push harder than you think you should. Make sure that nothing is obstructing the connection.
Also, the drive may be bad. If you have an external enclosure, you can see if you get the same result with it in there.
By the way, which HDD did you purchase?
-GDF

Similar Messages

  • IMac 400dv will not recognize new hard drive installed

    Hi,
    I had been having trouble with my iMac 400dv's hard drive. I had posted the problems I was having and had gotten some very nice feedback. The final decision was to install a new hard drive and battery.
    I purchased a refurbished 40GB Maxtor to replace my old 20GB. Installation was no problem except that my iMac will not recognize the new drive. If I reinstall the old one, it recognizes it right away, so I know it has been installed correctly.
    I took the new hard drive back to the store and the tech said that it wasn't set on the "Master" position. He set it and tested the drive and said that it was fine. I reinstalled and get the same result, no drive can be sellected to install the software. No matter where I set the pin, I get the same result. I called the phone help line (MicroCenter) and the new tech told me that the drive was too big for my mac, which makes no sense to me since they suggested I buy a 100GB in the 1st place.
    I have 1GB of memory, my installation disk if for 8.6 and I will bring it up to 9.2 if I can get it running again.
    Any suggestions?
    thanks,
    Lucy

    Lucy Rust...
    In my opinion no Macintosh user should attempt to install a refurbished HD under any condition. Especially any HD that is to be bootable as they are no longer reliable for the Mac.
    Master setting is a must for the HD and never tinker with an optical setting. Well, if you could mess with the optical setting, expect to do some micro-surgery.
    You should be good for a HD up to a capacity of 120GB. The threshold is somewhere around 137GB but you will not find such odd capacity on the market.
    I think the rest has been covered.
    ...Ron

  • System Profiler will not recognize installed hard drive if drive is in use by VMWare

    System Information will not recognize installed Hard Drive (Boot Camp) when in use by VMWare.
    I work in IT for a School District and I am creating a Script that system information about the computer. I am testing this on a Mac Pro with two internal hard drives. One drive is Mac OS 10.8 and the other drive is a Boot Camp Drive that is used by VMWare Fusion.
    When I run System Information via the GUI or system_profiler via Terminal, both drives show up just fine. However, if I launch VMWare Fusion and run Windows from my Boot Camp drive, then run System Information via the GUI or system_profiler via Terminal, the Boot Camp Drive is no longer listed as an installed drive.
    Example:
    In the Terminal, I enter the following command.
    system_profiler SPStorageDataType
    Then it returns this information.
    Storage:
        Lion Client:
          Available: 217.84 GB (217,836,306,432 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
        BOOTCAMP:
          Available: 255.58 GB (255,575,560,192 bytes)
          Capacity: 319.79 GB (319,790,510,080 bytes)
          Mount Point: /Volumes/BOOTCAMP
          File System: NTFS
          Writable: No
          Ignore Ownership: Yes
          BSD Name: disk1s2
          Volume UUID: D4B39D4E-E244-403C-AE4D-4D58397130DE
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    Then I launch VMWare, which uses the Boot Camp drive. The once again run the same command from the Terminal Command and I get this.
    Storage:
        Lion Client:
          Available: 213.39 GB (213,392,244,736 bytes)
          Capacity: 639.28 GB (639,275,270,144 bytes)
          Mount Point: /
          File System: Journaled HFS+
          Writable: Yes
          Ignore Ownership: No
          BSD Name: disk0s2
          Volume UUID: CCB501BF-AF24-30E7-A938-5A4E52DF14D7
          Physical Drive:
              Media Name: WDC WD6400AAKS-41H2B0 Media
              Medium Type: Rotational
              Protocol: SATA
              Internal: Yes
              Partition Map Type: GPT (GUID Partition Table)
              S.M.A.R.T. Status: Verified
    The Boot Camp Drive is no longer listed.
    I assume this is due to the the fact that the drive is "In Use" however is seems odd since the Mac drive is also in use and it appears without problem. I assume there is no "fix" for this, I was just wondering if someone may have an explaination why?
    Also, I do realize that I can query the various interface types like system_profiler SPSerialATADataType to get all the properly installed phycial drives, but then I would have to query all possible interface types, isolate only devices containing Volumes, then consoldate the information to just the information that I need. I was hoping for a cleaner query.

    Thank you for your response.
    VMWare may be the cause, but the actual issue I am having is with Apple's System Information. I anticipated resistance from VMWare if I went to them with a question about an Apple software issue (even though VMWare software is part of the equation). I was trying to avoid the inevitable finger pointing game. I thought I would try with Apple Forums first since the issues presents itself within the Apple Software. However, you are correct that VMWare may have an explanation on why Fusion might be interfering with System Information. I will check with them next.
    To answer your question. Yes, In most cases I do use Fusion to run Windows side-by-side with the Mac OS. However, that is not always the case. There are a few reasons why I have it setup using a Dual Boot configuration.
    One, in some cases, due to the intense programs I occasionally run (graphic applications), I prefer to simply boot straight into Windows via Boot Camp so I may allocate all hardware resources to Windows. Additionally, some graphic applications like to have direct access to hardware and the extra layer of the VM environment can cause problems when an application is trying to directly access specific hardware like a graphics card.
    Second, I often use either side, both Mac and PC, for testing. There is an advantage to not having to rely on the Mac OS to run Windows. If, for whatever reason, my Mac becomes unstable due to testing, I can still jump right into Windows to do work if necessary.
    Third, I love the Mac OS, but I work in a PC centric organization. If there is a "problem" with my system, it is too easy for other system admins to say, "it's because it's a Mac". Having the definitive separation of the OS's allows me to prove that the Mac OS is not a factor.

  • I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    I have iMovie 09. I just erased my external hard drive, but it is still formatted for the mac. However, iMovie will not recognize the hard drive. It shows the only hard drive available is the computers. How do I get the external hard drive to show up?

    In Finder's Menu, select Go menu>Go to Folder, and go to "/volumes". (no quotes)
    Volumes is where an alias to your hard drive ("/" at boot) is placed at startup, and where all the "mount points" for auxiliary drives are created for you to access them. This folder is normally hidden from view.
    Drives with an extra 1 on the end have a side-effect of mounting a drive with the same name as the system already think exists. Try trashing the duplicates with a 1 or 2 if there are no real files in them, and reboot.
    If it does contain data...
    http://support.apple.com/kb/TS2474

  • HP dv7 will not recognize second hard drive

    My HP dv7 2185dx running Windows 7 will not recognize second hard drive, bios recognizes it, Intel Rapid storage recognizes it.
    Primary hard drive is a 1TB, in install a second 500GB hard drive.
    This question was solved.
    View Solution.

    Hi,
    Hold down the Windows Key and press R.  Into the Run Box type compmgmt.msc and hit enter.  Click Disk Management in the left pane and let the drives load up. 
    Does the 2nd HDD show here?
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • CLASSIC will not recognize my zip drive

    classic will not recognize my zip drive...i have one program that roland will not update and it only runs in os9...so the program opens but will not let me select the zip drive as a option...please advise if classic can detect zip drives etc...thanks soo much...
    oh and the driver for os9 is installed etc as well...

    1 is the Zip drive a SCSI, a ATA, or a USB Zip? Or are you talking about a flash memory drive?
    2 if you're not talking flash memory, do you have a disk inserted into the drive, and is it formatted HFS or FAT?
    3 if you are talking flash memory, is the flash drive formatted HFS or FAT?
    4 can you get to the desktop in whichever application this is?
    5 which application is it that you're trying to use?

  • Windows 7 will not recognize the dvd drive in my dv9925nr

    Windows will not recognize my dvd drive in Windows 7. It shows up under device manager under cd drives, but will not list in in my computer and will not recognize it as a drive in burning applications.

    I haven't installed and started testing the BETA yet, just downloading from MS tonight.I would suspect upper & lower filters,since that is the most common cause of cd/dvd problems from XP-Vista.
    http://support.microsoft.com/default.aspx/kb/929461
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • I connected my iPad to wireless, now my MacBook will not download new mail (Charter) unless I turn the iPad off. Please help?

    I connected my iPad to wireless, now my MacBook will not download new mail (Charter) unless I turn the iPad off. Please help?

    Is there anything in this link to help, particularly in the Troubleshooting section at the very end? http://www.myaccount.charter.com/customers/support.aspx?supportarticleid=2234

  • My Laptop Pavilion 9700 will not recognize DVD/CD drive. Does not show up in Device Manager

    My laptop Pavilion 9700 will not recognize the DVD/CD drive:
    The drive does not show up in the Device Manager’s list:  The disk spins and the light is on: Use a
    paper clip to open the door;  I updated
    to Sevice Pak 2 recently, but I am not sure if this has anything to cause this
    problem:  Please Help, anyone!
    Thanks

    Hi,
    Follow the procedure on the link below to create a bootable Ubuntu CD and follow the steps in Part 3 to 'Try it' to see if this OS will run from the CD without the need to install on your HDD.  This will show whether the problem is with Windows or a Hardware problem with the optical drive.
    http://www.ubuntu.com/desktop/get-ubuntu/download
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Satellite P505D-S893​5 will not recognize DVD/CD Drive

    04/04/2011 My Laptop P505d-S8935 will not recognize the DVD/CD Drive.  It worked yesterday but not today.  I looked under properties and it showed not working properly....could not find driver.  Checked driver update....found driver.  Still not working.  Please advise.

    Satellite P505D-S8935 
    it showed not working properly....could not find driver.
    Please quote the message on Properties' General tab under Device status.
    -Jerry

  • T60 hard drive replacement - Windows does not recognize the hard drive

    Hello All, new to the Lenovo Community. I have a T60 as well as newer Lenovo Edge. The HD crashed on the T60 and it will no longer boot. I just purchased a WD 500GB without doing a lot of research. In trying to install Windows 7 (I had already upgraded the T60) it will not recognize the new drive - Windows does not see the drive at all. Is there a way to get the Lenovo to recognize the WD drive? Thank you in advance for any help.
    Solved!
    Go to Solution.

    Glad I was able to help.
    Just be careful, the usual "if it doesn't fit, find a bigger hammer" doesn't apply to this model laptop.
    Also, there is a part available to adjust the frustration level, I don't happen to have the FRU number available, but I do have a photo and I'm sure you can find a local shop to provide it. Any experienced vendor should be able to match up a similar item from this photo.
    It comes in many varieties, this model has a handy extention to aid in installation so you can easily do it with one hand. Others may require two hands to safely install. Use care when installing, one slip can destroy your laptop. Acute abuse can lead to severe embarassing situations and cronic abuse can have impact on your health, so use wisely and always get a spare to share with a friend. They tend ot come conviently packaged in quantity of 6, so you can invite a few friends over.
    This invention has saved many a laptop from sailing out of windows worldwide.
    ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

  • Itunes will not recognize new folder

    Hi!
    I'm trying to get iTunes to recognize a folder on an external hard drive as the main music folder.
    I've gone to iTunes>Preferences>Advanced and changed the folder to one of my external, but even after repeated attempts it will not recognize this folder.
    Am I doing something wrong?
    Any help or suggestions would be much appreciated.

    < I've gone to iTunes>Preferences>Advanced and changed the folder to one of my external, but even after repeated attempts it will not recognize this folder.
    It's not supposed to add music from that folder.
    It will use that folder for everything in the future you add to iTunes.
    You add music to iTunes by File -> Add to library and select the folder where the music is.

  • ATHORIZED COMPUTER WILL NOT RECOGNIZE NEW IPOD TOUCH

    I TRANSFERRED PURCHASES FROM OLD IPOD TOUCH TO COMPUTER SUCESSFULLY. PLUG IN NEW IPOD TOUCH TO SAME COMPUTER TO SYNC TO IPOD BUT COMPUTER WILL NOT RECOGNIZE THE IPOD. WAHTS UP?

    before i transferred purchases from old ipod touch, i plugged in the new ipod touch by accident and the box that says new hardware found came up. so i unplugged it, plugged in the the old ipod touch transferred puchases, backed up to computer, that part went fine. plugged in new ipod touch and nothing happens. it's like it doesnt read it anymore

  • Itunes/ computer will not recognize new ipod nano

    i just bought a new ipod nano 3rd generation and my computer and itunes will not recognize it. i have downloaded the newest version of itunes and my computer meets all of the requirements, and it still is not working. the ipod guide that came with it said that setup assistant should come up, yet it has not.
    Message was edited by: ncheels91

    There's a long article about that problem:
    http://docs.info.apple.com/article.html?artnum=93716
    You have to go step by step, starting with: does Windows recognize the iPod?

  • Will not recognize internal hard drive

    I have a strange problem with a 2009 MacBookPro.  It started acting "strange" for the user over the past few months.  By "strange" I mean it would freeze, or fail to boot, or sometimes even restart without any reason.  Now, it gets even stranger.  Tried the standard things,  RAM reseat, replace, check for loose connectors etc.  It would fail to boot when the hard drive was connected internally.  Then it would give a kernal panic and fail to even recognize a hard drive as being installed.  Did a PRam reset, SMC reset and even the power off/control key to try to reset the open firmware.  No sucess with anything.  This is a suystem with an internal battery.
    Yet, when using this exact same hard drive on an external USB drive connection, it would boot fine.  Next tried it in Terminal mode to boot up another MBP.  Failed to boot.  When the 2nd MBP was booted from its internal drive and the suspect machine was plugged in as a Firewire (Terminal mode on "strange" computer) an External Firewire Drive appeared on the desktop, then a few seconds later, an identical copy of the first Ext FW drive appeared.  This went on with evenbtually six copies of the one single Terminal booted hard drive appearing on the desktop of the second computer.  None of the six drives would open or even allow any indiccation of what they contained.
    Tried to partition the hard drive when it was put back into the internal slot but it would not unmount and failed to partition.  The same thinmg happened when trying to erase it.  Connected the hard drive via USB to a Windows 7 machine and used it to erase both the Recovery and Main partitions from the ard drive.  Both were erased but the EFI partition could not be erased or cleaned.  Put this same hard drive, as an external USB, into a very old XP machine and there the EFI partition was removed when a "Clean" command was sent via command line.
    I then took the, now totally erased hard drive, and put it back into the computer as an internal drive and booted the computer from a 10.8 USB stick so I could partition the now empty hard drive.  The drive was not even recognized as being present.  Did the same thing, but using the USB external connection for that same hard drive.  It partitioned and then formatted with 10.8.1 (what was on the USB stick).  After the OS was installed, the computer would boot using this newly created OS when connected as an external USB drive.  Put the drive back in as the internal drive.  Got a Kernal Panic.  Forced shutdown and retried.  Noi kernal Panic but drive was not even recognized.  Pulled the drive from internal and put it back into the external USB and tried booting.  System would not recognize the drive as even being present.
    I then erased and cleaned the drive in the XP machine again and then, using the USB connection on the second computer reinstalled 10.8 from the USB.  When I tried the now newly created software again, the same thing happened as listed above. 2nd machine booted fine on the drive as a USB, "Strange" machine booted fine using the drive as an external USB, Kernal Panicked then would not be recognized in the "Strange" machine.
    It appears that when the drive is connected internally. it not only does not have the OS software recognized but will rewrite something in the drive that makes it impossible to be recognized by any Apple.  My first thought was that the EFI partition was corrupted somehow so that was why I tried cleaning the EFI partition along with the other two partitions.  But even with a new EFI and other partitions, the drive was not useable once it was used to try to boot as an internal drive in the suspect computer.
    Now here I am dropping into speculation mode.  My guess is that something in the very basic ROM (Pram?) that recognizes a hard drive is in the internal slot and tries to get to the EFI instead fails and in the process it screws up the EFI (or maybe even an address table?) in the hard drive.  If it recognizes that there is no internal hard drive, it will happily boot from either a USB stick, a USB connected external hard drive or a Firewire/Terminal mode computer connected to it.
    Sounds like a motherboard problem but I am wondering if it is possible to "flash" the very basic ROM that is at the start of the process back to factory default or maybe just replace the chip if it is the same one used as part of the Firmware password protection system.
    Anyone have any other ideas or thoughts about possible solutions or at least a way to definitely identify what the problem's cause?

    Answer has been found.  The internal drive SATA cable was replaced and the system is now working correctly.

Maybe you are looking for