On an M425dn, I am unable to setup scan to network folder on a home wireless network

On an M425dn MFP, I am unable to setup 'Scan to Network Folder' on a home wireless network. The network folder exists and has been set to share with full permissions for everyone. The OS is Windows 7. The printer IP address is 192.168.1.104. I have used this in a browser to access the setup tab called Scan. I have established a network folder and have attempted to test the setup folder multiple times. The tests end in one of two ways. The attempt spins endlessly which requires a cancel action or it ends with the following error: "Cannot connect to the network folder. Ensure the shared folder name is correct." The network folder does indeed exist.
The computer name is Delta. The shared folder name is Images on my A: drive.
So the network path entered is \\DELTA\Images. By the way, printing to this network printer is always a succesful operation. Any guidance to solving this dilemma will be greatly appreciated. Thanks in advance.

Google may have "locked" IMAP and/or POP access to your account. To unlock it go here:
https://accounts.google.com/b/0/DisplayUnlockCaptcha
Then try setting the account up on the phone again.

Similar Messages

  • Unable to join home wireless network

    One of my iPhones wont join my home wireless network.  Keeps saying password is incorrect.  Two other iPhones, 3 iPads, laptop all join no problem.  Tried resetting wireless settings, did not work.

    I'm having the same problem, but I have an iPhone 4 and mine won't connect to any network. It always says "unable to connect to network". I looked through all of the support forums but all I can find are people saying that its the firmware and that Apple has to fix it in an update or have to switch it out, and my warranty has expired. All of those forums are also from 2009. I don't want to pay for unlimited Internet, so I new this to be fixed. Please help if you at all possibly can.

  • Unable to connect to home wireless network with my iPod touch

    I've had my iTouch for several months now and I'm still not able to connect to my wireless network at home. I've tried the resets and other suggestions I've found in the discussion groups but nothing has worked.
    I have an older Netgear Router MR814v2 and it is unsecured. It is attached to my old desktop, HP Pavilion running Windows ME, which is not able to run the itunes software. My HP laptop is where my iTouch and iTunes software is installed.
    The iTouch displays my network with good signal strength, but when I try to connect I get the "unable to join the network "NETGEAR".
    Going to my router, it does not recognize my iTouch as an attached device. Why is that and what am I missing?
    Thank you for all suggestions and your help.

    I tried powering down the router. When it's off the iTouch does not recognize the network and then when it's powered on again, the iTouch recognizes the network. Unlike the public wi-fi spots that my iTouch responds to, where all the info like IP Address, Subnet Mask, Router, DNS etc are populated in the settings...my iTouch does not populate these fields at home even though it recognizes the network. I still get the unable to connect to network error. Could it be that my router is antiquated and can not support the iTouch? Like I said earlier, my Router does not recognize the iTouch as being attached to it.

  • Unable to Access My "secure" home wireless network

    Airport works fine when finding unsecure networks requiring no password to log on, such as in public areas. But it won't work thru my secured wireless network. I use a D Link wireless router. Air port "sees" the network, but it requires a log on to gain access for the first time. I'm positive I have the right password. I've spent a lot of time with the ISP here in Kuwait, and granted, MAC isn't their strong suit, but they keep pointng back to the problem being with the computer. I can plug into the router with a cable and everything is fine and I can access my neighbors unsecure network thru his router...thanks neighbor. Any suggestions?
    Mac Book Pro 17"   Mac OS X (10.4.10)  

    I was having similar problems few things.
    1. Check to make sure drivers are up to date for Dlink. I would double check your settings for your router.
    2. This is more of a question. Do you have a lot of people that come over to your place and use your appartment? I was having problems with my Linksys Router and I decided to setup a Mac filter instead.
    3. Hard reset the router.
    4. Check D-links website see if the have any information regarding router problem.

  • I am new to IPod touch and really enjoying it.  BUT.  All of a sudden I am unable to connect to my home wireless network nor any hot spots.  Did not have any trouble in 1st month and yet something seems to have changed.  Any suggestions as to what ?

    I am new to IPod Touch and enjoying but all of a sudden (after about a month of connection) I am unable to connect to either my home wirless or hotspots outside of home.  It would appear that a setting has changed but have no idea how to determine.  Any suggestions ?

    NO I did not and thank you very much for the advice.  My problem was stated incorrectly in that while I am able to connect to the wireless from that point on I am unable to connect to the internet.  I will check the article referred to.

  • Unable to connect with Windows 7 laptop on home wireless network

    When I initially set up my network, both computers were able to see each other. I could access the Mac's files on the Windows 7 PC, but not vice versa. The Mac required a user name and password when I clicked on the PC's icon in Finder, but wouldn't recognize anything I'd type in.
    I tried duplicating the Mac network location and entering "WORKGROUP" under the WINS tab. This caused the Mac to lose sight of the PC altogether, and still can't see it when I switched back to the original location. The PC can still see the Mac.

    I'm not sure if this help. I have a Macbook Pro with Magic Mouse in Window 7.
    What I did was when you click on the Bluetooth >> Add a Device, the Magic Mouse will show in the pop up window.
    Do not click "Next", instead right click on the Mouse and select "Properties".
    Under "Services" tab, checked "Drivers for keyboard, mice etc (HID). Then click "Apply". Driver will be installed once is done click "OK"
    Then click "Cancel" on the Add a device windows. The magic mouse should be connected now and shown in the Bluetooth Device list.
    Hope this help, at least it does works for me. Cheers

  • Unable to connect to home wireless network

    Hi -
    I just got my 16mb Iphone 3G and tired to get it to sign on to the wifi network at home. It sees the ssid but just won't sign on. I have a open network, so there shouldn't be anything that will prevent it from getting on to the network. Please advise

    When you try to select your network name on your iPhone, does the phone then show a tick next to the network name? If it does, then tap the clue arrow and see if your phone has a registered IP address. If it doesn't, then check out the various articles on the apple support site.
    If it does show an IP address but still won't connect to the internet, itunes or app shop etc, then it may be a wlan b/g problem that people have recently started mentioning. Check out the other posts for more info on that.
    Stuart

  • Unable to setup eprint

    Unable to setup eprint.
    My printer was working with eprint fine until I got a new router. Since then I cannot seem to use or setup eprint.
    It is connected on the home wireless network and this is working fine to print documents.
    I have reset factory settings for webservices but still no luck. Keep coming up that I am not connected to a network and wants a proxy
    Can anyone help
    Thanks
    This question was solved.
    View Solution.

    Try restarting your Wifi - Router. 
    Check the maximum number of devices that can be connected to your Wifi - Router.
    Try disconnecting other devices and connect your Printer and Laptop to the router and try the below option.
    EPrint Setup Process for your printer.
    1. Connect the printer to a network with Internet Connection. (Make sure your laptop or Computer is connected to the same network as Printer)
    2. Check the Printers IP address on the printers front panel.
    3. Type the IP address of the printer on a browser on your computer and press Enter.
    4. On the Webpage that appears click HP Web Services Tab.
    5. If your network supports proxy you can add the proxy in this page.
    6. Review and accept the terms of use, and then click Enable Button.
    7. The printer should print an information sheet with code on that.
    8. <code>@hpeprint.com will be your email ID.
    This is just a method to register the printer to cloud from the Laptop. You can also try to register the printer from front panel as well.
    Hope this helps.
    "Although I work for HP, I'm speaking for myself and not on behalf of HP"--Please mark the post that solves your problem as "Accepted Solution"
    "Say "Thanks" by clicking the Kudos Star in the post that helped you.

  • Photosmart 6510 unable to connect to wireless network.

    The wireless icon on my printer indicated "Not Connected" and showed this information
    IP Address: No Link
    Network Name: N/A
    MAC: A0:B3:CC:12:3A:07
    When running the Wireless Setup Wizard and selecting the internet network my computer is currently connected to, it then said that it was "Unable to connect to network. Unsupported authentication or encryption type." I ran a wireless network test and next to "Network Name (SSID) Found" is says "FAIL". If you need more information that can be found on the netork test results I will be happy to give you them. I do not have access to the router as I am currently at my university. It is a secured network so I'm thinking this is where the problem is coming from. Also, whenever I try to type in my IP address into my URL bar the page is not found. Any suggestions? Or am I just going to have to purchase a USB cable?

    Here's other information from my Wireless Network Test Results.
    Wireless:
    -Wireless On- Pass
    -Wireless Working- Pass
    -Signal Quality- Not Run
    Connectivity:
    -Connected- Not Run
    -Disconnect count total- 0
    -Disconnect count (last hour)- 0
    -Disconnect count (last 24 hours)- 0
    Network:
    -Network Name (SSID) Found- FAIL (All this was in bold)
    -Other networks detected matching your network name (SSID)- Not Run
    -Wireless Networks Detected- 10
    Settings:
    -Printer Settings Consistent with Wireless Router Settings- Not Run
    -No Filtering- Not Run
    -Channel- Not Run
    -Security- Not Run
    Current Configuration:
    -Network Name (SSID)- Not Set
    -Hardware Address (MAC)- a0:b3:cc:12:3a:07
    -IP Address- Not applicable
    -Configuration Source- Not applicable
    -Communication Mode- Infrastructure
    -Authentication Type- Open System
    -Encryption- None

  • Setup wireless network for mac and pc with Airport Express?

    Mac Mini/OSX/10.8.2/Airport Express
    Question,
    I have my AIrPort Express setup for my Mac Mini and I have dell computer that I want to share the wireless network. Is it possible to setup a wireless network with my mini and the pc using only the AirPort Express? Is the Airport Express a wireless router?
    Thanks,

    If your Mac Mini is connecting to the Express using wireless, then this confirms that the device is working correctly. 
    The Express is a wireless router that can support up to 10 wireless connections, so your Dell computer should be able to connect assuming that its wireless card is working correctly, and the Dell indentifies the network and enters the correct wireless network password.
    If you are having difficulty with the Dell PC connecting, this Windows troubleshooting document might help:
    http://windows.microsoft.com/en-US/windows/network-connection-problem-help#netwo rk-problems=windows-8&v1h=win8tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  • Network Folder Setup - "No Write Permission​". Windows Vista.

    Product: 8600 N911g
    I am having issues in creating a network folder to scan to my computer. It responds ‘No write permission’
    **NOTE**Before I allow you to continue reading, I need to first know to I need to create a password in my user account, or turn off UAC to create a scan network folder on my PC? If so, then that is what I need to do to correct this issue.
    Steps I have performed in attempting to accomplish this task:
    In Windows to create shared folder:
    1) Created folder.
    2) Open folder properties, under 'sharing' tab, selected 'Share' button, then selected 'Share' button.
    3) A dialog window appears and states 'Sharing items', and when it is complete, it states "Your folder is shared. You may e-mail these links to notify people that you have shared these files, or copy the links onto the Windows clipboard, where you can paste them into any program you choose.”
    4) When I select ‘Done’, it returns to the folder properties, and states in ‘Network File and Folder Sharing’ under ‘Sharing’ tab under ‘Network Path’: ‘Not Shared’.
    **I don’t understand that it just said ‘Your folder is shared’, then under Network Path is stated ‘Not Shared’.**
    5) Since in stated ‘Not Shared’, I selected ‘Advanced Sharing’, checked ‘Share this folder’ box, and under ‘Permissions’, checked ‘Full Control’ box.
    6) Now it states Shared, and under ‘Network Path’ states the location: ‘ \\ADMIN-PC\ScantoDV9825 ’
    In the HP Officejet Pro 8600 N911g, Embedded Web Server to add network folder to scan to:
    1) Opened ‘Scan’ section by clicking on the tab ‘Scan’. Under ‘Network Folder Setup’, the ‘Network Folder Configuration’ clicked on ‘New’.
    2) Entered data for the following fieldsTEP 1 OF 4: Display Name: ‘Scan’, Network Path: ‘\\ADMIN-PC\ScantoDV9825’. Left User Name and Password fields blank. STEP 2 OF 4: Left PIN fields blank. STEP 3 OF 4: Did not make any changes, used default settings.
    3) In STEP 4 OF 4 when I click on Save and Test, it returns with the message ‘No write permission’
    How do I resolve this issue of ‘No write permission’?
    Thank you.
    ~Robert M.
    This question was solved.
    View Solution.

    Hi Robert,
    First ensure the permissions are also set correctly by right clicking the shared folder, and then open the Security tab.
    If your user name is not listed as Full Control click the edit button, add your user name and check the box for as Allow full control.
    If that does not help, follow these steps in Windows Vista to make sure that your computer is configured to allow network sharing.
    Step one: Make sure that the computer user account is password protected
    Click the Windows icon ( ), and then click Control Panel .
    Click User Accounts , and then select the account you used to log into the computer.
    Click Change your Windows password , and then find the user account you used to log into the computer.
    If the user account is password protected , continue to the next step.
    If the user account is not password protected , click Create a password for your account to create a password, and then continue to the next step.
    Step two: Define the network location
    Click the Windows icon ( ), and then click Control Panel .
    Click Network and Internet .
    Click Network and Sharing Center .
    Click Customize next to Your Network . The Set Network Location window opens.
    Select Private , click Next , and then click Close .
    Step three: Make sure that the network sharing and discovery options are correct
    Open the Network and Sharing Center window.
    In the Sharing and Discovery section, make sure that the following network options are set to On :
    Network Discovery
    File Sharing
    Public Folder Sharing (password required)
    Printer Sharing (password required)
    Password Protected Sharing
    Your computer network is now successfully set to complete the Scan and Fax to Network Folder or Digital Fax to Network Folder Wizard.
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • This AirPort base station was unable to extend the wireless network.

    I have an AirPort Extreme in the lounge connected to BT infinity.
    I also have an airport express in the kitchen connected to a stereo system.
    I have had this set up for around 12 months.
    The airport express will not extend the wireless network.
    I reset it, restart, factory reset etc and it will work fine for around 3 days, then I get the same error message saying
    This AirPort base station was unable to extend the wireless network. Make sure the wireless network you’re trying to extend was set up and is working correctly, that you entered a matching wireless network password into this device, and that this device is in range of the wireless network.
    The express is situated easily within range of the extreme. And the airplay between those two, my iMac and two apple tv's works pretty much as it should.
    Can someone please shed some light on this?
    Maybe I have it in a wrong setting or summut....

    G Beach wrote:
    I am also experiencing a recent failure in my Airport devices no longer extending my wireless network. 
    My Aiport Express and second Airport Extreme were extending my wireless network for more than a year
    The only change that has taken place lately is that the firmware for both devices was upgraded to 7.6.4, however the upgrade was only in response to trying to resolve this problem.  Needless to say, the firmware upgrade did not resolve anything.
    If I didn't know better, I'd have thought I wrote the above. 
    I have a TC from a few years ago (last one before the tower, I think), plus the older AEBS that it replaced extending the network, plus a 1-year-old Express also extending. I had upgraded them all to 7.6.3/4 when it came out, but reverted them all to 7.6.1 when everything went crapways (others having the same issues of the LAN regularly croaking), and didn't bother upgrading again since. 
    Today I just tried 7.6.4 on all of them, and it seemed OK at first with green lights all around in Airport Utility.  Then I made one change, which was to enable 5Ghz on the main AEBS/TC only (the express doesn't need it, and the older AEBS can't do it).
    The latter two started flasing amber and giving the "unable to extend wireless network" error message.
    So I'm wondering if you are similarly using 5Ghz?

  • Time machine setup - how to change 'wireless network name' and settings?

    I have moved laptop to Mountain Lion.
    This is the first time to backup to Timecapsule.
    I went to Settings then Select Disk and selected existing Time Machine.
    It took more than 30 minutes and seemed stuck on 'Preparing ....".
    I cancelled and tried to 'Setup Time Capsule not  listed"...
    The system recognised the Time Capsule but I see that the network settings is my old 'wireless network' name.
    How do I change this to the correct network name and ensure that the settings are correct? 
    I think if this is corrected, the backup will work.
    Thanks in advance.

    On the Home screen of the product control panel, touch the right arrow ( ) to view more options.
    Touch Setup ( ).
    Touch Network .
    Touch Wi-Fi Protected Setup .
    Touch PIN .
    Touch Start . The product displays a PIN.
    NOTE:The product begins a timer for approximately two minutes to allow you time to enter the PIN on the networking device.
    Enter the PIN on the WPS-enabled router or other networking device.
    I work for HP, IPGHT specialist in Officejet and Photosmart printers.
    --Say "Thanks" by clicking the Kudos Star in the post that helped you.
    --Please mark the post that solves your problem as "Accepted Solution" .....

  • HT5552 I am unable to setup payment method using American Express.

    I am unable to setup payment method using American Express.

    Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • I have a sync account and used to keep sync with firefox server. Now computer got re-installed and want to sync data from firefox sync server. But I am unable to setup as i dont have sync key.

    I have a sync account and used to keep sync with Firefox server. Now computer got re-installed(OS) and want to sync data from Firefox sync server. But I am unable to setup as i don't have sync key.
    I would like to just sync with Firefox Sync Server with existing account. I can not find any way out for this. please reply me on
    [email protected]

    hello, for the old sync system in firefox 28 and below you also had to sign up with a mail address and password originally - to connect firefox to the old account you would need to have all those three pieces (mail, password & recovery key) available to you unfortunately...

Maybe you are looking for