On Interface show collisions?

What is mean by display collisions numbers on interface of ASA Firewall?
Thanks in advance..

Hi Abhinay,
If you are looking for what are collisions in the show interface output on ASA, they occur when the ASA and the connected device try sending traffic at the same time. Please check the following link for more information :
http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfd6.shtml
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a008009491c.shtml
Thanks.

Similar Messages

I am having trouble with my Mac Mini's ethernet connection. Defining a new network interface shows no ethernet adaptor. Reloading SL from DVD repaired. But SL update lost ethernet again. Will Lion Fix?

I am having trouble with my mac mini ethernet. It had been working for weeks after an update to SL 10.6.8.
Once it went out and i repaired it by defining a new connection from System Preferences ->Network->(left panel service, +).
But yesterday, after a power up. my ethernet was not working again. I tried this old trick to repair it, but the interface choices
listed for '+' a new service did not include Ethernet any more. And the Utilities->System Profiler->Ethernet Cards shows
no ethernet available.
As a last ditch effort i reloaded my original SL from DVD. (I think it was version 10.6.4 but i could be mistaken on the version).
The ethernet worked! But KeyNote wasn't going to work because apparently the version i purchased depends on 10.6.8.
So I upgraded again to SL 10.6.8 (Plus some other updates like AirPort which i don't use).
Now the Ethernet is not working again. I see the same symptoms as before with the Ethernet seeming not installed.
Is this a problem seen by others?
Would going to Lion fix the problem?
Could AirPort actually be the culprit and not SL?
If i stay with my original SL, would i need to repurchase a version of KeyNote for the older version of SL?

Have you reset the SMC?
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
While you're at it, resetting the PRAM won't hurt anything and 'might' help is SMC reset didn't work (PRAM does some port control):
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
Something else you might try .... you don't say how you're updating to 10.6.8, however, if you're using Software Update, you might try downloading the 10.6.8 combo update, which contains all updates to 10.6. Sometimes, Software Update doesn't work quite right, and installing the combo update fixes that. Download the update from Apple's download site at http://support.apple.com/downloads/ , using Disk Utility repair permissions, apply the combo update, then repair permissions again.

Interface showing NO-CARRIER & DORMANT, but working

Long time Linux user, first time Arch user. Trying to configure ArchARM on a Rasp Pi (Not sure that's related).
Note - I'm totally new to systemctl and netctl, been using Redhat-like systems for a long time....
I was converting the standard install of dhcpcd to a static IP assignment. I did the following:
cp /etc/netctl/examples/ethernet-static /etc/netctl/eth0
vi /etc/netctl/eth0 # (and set IP, gateway, etc. as appropriate)
systemctl stop [email protected]
systemctl disable [email protected]
ip link set eth0 down #netctl seems to need this or its not happy
systemctl start [email protected]
systemctl enable [email protected] # Not sure what is netctl vs netctl-auto
At this point all was good and things were working as expected.
I then rebooted the system and when I reconnected, I looked at the network:
[root@alarmpi ~]# ip addr show dev eth0
4: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DORMANT qlen 1000
link/ether b8:27:eb:c2:4e:2e brd ff:ff:ff:ff:ff:ff
inet 192.168.1.4/24 brd 192.168.1.255 scope global eth0
Note - the interface is working, I'm connecting (via SSH) over it, etc. But, it makes no sense to me why it would indicate NO-CARRIER and DORMANT. Why is the OS not recognizing the link as UP? Seems the NO-CARRIER and UP/LOWER_UP flags are conflicting, no?
Thanks.
Also, any pointers on learning more about systemctl and netctl would be appreciated (can't find a good primer anywhere...)
Last edited by stevelipinski (2013-11-15 17:08:44)

Welcome to the bbs, however, please note ARM is covered elsewhere: https://bbs.archlinux.org/viewtopic.php?id=153431
The command's output is misleading. You see another UP inside the brackets, that's the relevant one.
Please have a look at the wiki pages here first for pointers. For netctl the devs also put a lot of effort in comprehensive man pages which the wiki page tries to complement I guess.

BPC NW Web Interface showing blank content

Hi,
When i click on the BPC Web interface from the Admin Console, it is showing a blank page with Getting started, Live Reporting Frame header. I have checked with user authorization and everything. This is happening in the Server itself. Please let me know possible causes and solution for this.
Thanks,

Hi,
I've the same problem. There is only a blank page, if i want to work with the BPC Web Interface, regardless if I want to make 'first steps' or ' busisness process flow' or other.
I've checked the internet explorer settings and for testing I set it all to the lowest security level but it's not working, i still get the 'blank page'.
It would be nice, if you could explain which changing in the settings of the internet explorer solved your problem.
Many thanks
Michael Scholz

11G Cluster Install: Identify Net Interface shows wrong IP subnets??

I'm in the middle of an 11Gr2 cluster install.
On the screen where it has you Identify Network Devices,
On my eth0 (public) ip...and the eth3 (vip) listings...it has the wrong subnet.
Example...
11.8.224.0(shown by oui)....should be 11.8.232.0 for eth0
and
11.8.224.0 (shown by oui)...should be 11.8.232.0 for eth3
eth1, is shown correctly.
When I look at ifconfig...I confirm my subnet numbers should be ok. I cannot find a way on the OUI screen, to change anything about the subnet IP address. It will only let me change the "type" to public, private or do not use.
Any ideas where the OUI is picking up its information concerning the network interfaces?? I dunno why it is showing 224 rather than 232.
Any suggestions? I can't find anything about this on the Oracle support site...
This is on a RHEL5 box, 64 bit.
Thanks in advance,
cayenne

Yes,
you can configure etho or eth1 using
#system-config-networkafter changes done you have to restart the services, make sure both the nodes are not using same ethernet ports
service network restart

6807-XL - Control plane interface showing down in logs and NMS

Getting the below logs on the switch and NMS station is also showing the CPP interface is down.
Jul 01 12:09:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Control Plane Interface, changed state to down
Any thoughts?

Getting the below logs on the switch and NMS station is also showing the CPP interface is down.
Jul 01 12:09:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Control Plane Interface, changed state to down
Any thoughts?

No network interfaces showing

Hello everyone. I have been using arch linux for a few months now and loving it, except for one weirdly persistent problem with my wireless. In fact this is the third time it has happened to me and have been unable to fix it. The last two times I simply reinstalled arch after failure of any progress but that is very tedious, timewasting and most important unnecessary, so I am calling upon the arch-linux forum for help.
Basically my problem is this, I have been using wifi-menu to connect to my wireless network since I got arch and everything was going smoothly, no problems at all, until one day I booted up my computer and was unable to find any connections what so ever. At first I thought it was just my router crashing or something but everyone else was able to connect fine so I ran the command iw dev and was surprised to see that there was no output. It had discovered no connections or interfaces at all, not just my personal connection had dissapeared but so had all of my neighbours. I tried plugging in an ethernet cable to my laptop but was unable to receive any connection from that either. It may be helpful to note that in the past the interface for my wireless connections changed at random. It changed from wlp2s0 to wlo1.
Here are somethings that I have tried doing recently to fix the problem.
Although I doubted it would help me as my problem seems to be that I have no wireless interfaces available, I had heard that having multiple packages, e.g dhpcd and netctl, handling your connection at once can cause conflicts. I tried disabling all dhpcd services running because I believe netctl is what wifi-menu uses. Here is the current states of my services from the command systemctl list-unit-files.
UNIT FILE STATE
proc-sys-fs-binfmt_misc.automount static
org.freedesktop.hostname1.busname static
org.freedesktop.locale1.busname static
org.freedesktop.login1.busname static
org.freedesktop.machine1.busname static
org.freedesktop.timedate1.busname static
dev-hugepages.mount static
dev-mqueue.mount static
proc-sys-fs-binfmt_misc.mount static
sys-fs-fuse-connections.mount static
sys-kernel-config.mount static
sys-kernel-debug.mount static
tmp.mount static
systemd-ask-password-console.path static
systemd-ask-password-wall.path static
session-c1.scope static
alsa-restore.service static
alsa-state.service static
alsa-store.service static
[email protected] disabled
avahi-daemon.service disabled
avahi-dnsconfd.service disabled
canberra-system-bootup.service disabled
canberra-system-shutdown-reboot.service disabled
canberra-system-shutdown.service disabled
colord.service static
console-getty.service disabled
console-shell.service disabled
[email protected] static
cronie.service disabled
dbus-org.freedesktop.hostname1.service static
dbus-org.freedesktop.locale1.service static
dbus-org.freedesktop.login1.service static
dbus-org.freedesktop.machine1.service static
dbus-org.freedesktop.timedate1.service static
dbus.service static
debug-shell.service disabled
dhcpcd.service disabled
[email protected] disabled
dmeventd.service static
emergency.service static
ftpd.service disabled
[email protected] enabled
[email protected] static
gpm.service disabled
httpd.service disabled
initrd-cleanup.service static
initrd-parse-etc.service static
initrd-switch-root.service static
initrd-udevadm-cleanup-db.service static
ip6tables.service disabled
iptables.service disabled
kmod-static-nodes.service static
krb5-kadmind.service disabled
krb5-kdc.service disabled
krb5-kpropd.service disabled
[email protected] static
lvm-monitoring.service disabled
lvmetad.service static
mdadm.service disabled
[email protected] static
mkinitcpio-generate-shutdown-ramfs.service static
mysqld.service disabled
[email protected] disabled
[email protected] disabled
netctl-sleep.service disabled
netctl.service disabled
[email protected] static
[email protected] enabled
[email protected] enabled
nscd.service disabled
ntop.service disabled
polkit.service static
quotaon.service static
rescue.service static
[email protected] static
rrdcached.service disabled
[email protected] static
[email protected] disabled
systemd-ask-password-console.service static
systemd-ask-password-wall.service static
[email protected] static
systemd-binfmt.service static
systemd-fsck-root.service static
[email protected] static
systemd-halt.service static
systemd-hibernate.service static
systemd-hostnamed.service static
systemd-hybrid-sleep.service static
systemd-initctl.service static
systemd-journal-flush.service static
systemd-journal-gatewayd.service static
systemd-journald.service static
systemd-kexec.service static
systemd-localed.service static
systemd-logind.service static
systemd-machined.service static
systemd-modules-load.service static
systemd-networkd.service disabled
[email protected] disabled
systemd-poweroff.service static
systemd-quotacheck.service static
systemd-random-seed.service static
systemd-readahead-collect.service disabled
systemd-readahead-done.service static
systemd-readahead-drop.service disabled
systemd-readahead-replay.service disabled
systemd-reboot.service static
systemd-remount-fs.service static
[email protected] static
systemd-shutdownd.service static
systemd-suspend.service static
systemd-sysctl.service static
systemd-timedated.service static
systemd-tmpfiles-clean.service static
systemd-tmpfiles-setup-dev.service static
systemd-tmpfiles-setup.service static
systemd-udev-settle.service static
systemd-udev-trigger.service static
systemd-udevd.service static
systemd-update-utmp-runlevel.service static
systemd-update-utmp.service static
systemd-user-sessions.service static
systemd-vconsole-setup.service static
talk.service static
[email protected] static
tor.service disabled
udisks2.service static
[email protected] static
uuidd.service static
[email protected] disabled
[email protected] disabled
wpa_supplicant.service disabled
[email protected] disabled
-.slice static
machine.slice static
system.slice static
user.slice static
avahi-daemon.socket disabled
dbus.socket static
dmeventd.socket static
git-daemon.socket disabled
krb5-kpropd.socket disabled
lvmetad.socket static
rlogin.socket disabled
rrdcached.socket disabled
rsh.socket disabled
syslog.socket static
systemd-initctl.socket static
systemd-journal-gatewayd.socket disabled
systemd-journald.socket static
systemd-shutdownd.socket static
systemd-udevd-control.socket static
systemd-udevd-kernel.socket static
talk.socket disabled
telnet.socket disabled
uuidd.socket disabled
basic.target static
bluetooth.target static
busnames.target static
cryptsetup.target static
ctrl-alt-del.target disabled
default.target static
emergency.target static
final.target static
getty.target static
graphical.target static
halt.target disabled
hibernate.target static
hybrid-sleep.target static
initrd-fs.target static
initrd-root-fs.target static
initrd-switch-root.target static
initrd.target static
kexec.target disabled
local-fs-pre.target static
local-fs.target static
multi-user.target static
network-online.target static
network.target static
nss-lookup.target static
nss-user-lookup.target static
paths.target static
poweroff.target disabled
printer.target static
reboot.target disabled
remote-fs-pre.target static
remote-fs.target enabled
rescue.target disabled
rpcbind.target static
shutdown.target static
sigpwr.target static
sleep.target static
slices.target static
smartcard.target static
sockets.target static
sound.target static
suspend.target static
swap.target static
sysinit.target static
system-update.target static
time-sync.target static
timers.target static
umount.target static
systemd-readahead-done.timer static
systemd-tmpfiles-clean.timer static
206 unit files listed.
I also tried disabling netctl@(my profile).service and left netctl@(my other profile).service (I have multiple profiles from when my interface name changed) enabled to make sure there were no conflicts there. Just so you know when my problem occurred neither wireless connections were enabled at the time. As I said I was using wifi-menu to manually connect after start up.
The only thing I have read about solutions similar to my problem is the mention of getting wireless drivers in the arch-wiki but I already have broadcom-wl drivers installed(although I may not have set them up this time over as they were not active meaning I was probably using broadcom brcmsmac/brcmfmac or b43). I thought that possibly my the drivers had somehow been disabled and when I checked with lsmod | grep broadcom nothing came up. I then loaded the module with sudo modprobe broadcom. Now lsmod | grep broadcom returns two results.
broadcom 7334 0
libphy 21639 1 broadcom
Here is what I currently get from lsmod | less.
Module Size Used by
nls_iso8859_1 4421 1
nls_cp437 5953 1
vfat 10119 1
fat 51960 1 vfat
cfg80211 431038 0
broadcom 7334 0
libphy 21639 1 broadcom
snd_hda_codec_hdmi 36588 5
uvcvideo 72804 0
videobuf2_vmalloc 3304 1 uvcvideo
videobuf2_memops 2335 1 videobuf2_vmalloc
videobuf2_core 29255 1 uvcvideo
videodev 122955 2 uvcvideo,videobuf2_core
btusb 20136 0
bluetooth 342577 2 btusb
coretemp 6390 0
iTCO_wdt 5375 0
hp_wmi 7595 0
sparse_keymap 3146 1 hp_wmi
6lowpan_iphc 11364 1 bluetooth
rfkill 15619 3 cfg80211,hp_wmi,bluetooth
nouveau 1080866 2
snd_hda_codec_idt 43700 1
snd_hda_codec_generic 53211 1 snd_hda_codec_idt
joydev 9631 0
media 12103 2 uvcvideo,videodev
mousedev 10464 0
kvm_intel 132876 0
iTCO_vendor_support 1929 1 iTCO_wdt
hid_generic 1153 0
ir_lirc_codec 4795 0
snd_hda_intel 37704 0
mxm_wmi 1467 1 nouveau
ttm 64361 1 nouveau
drm_kms_helper 35540 1 nouveau
snd_hda_codec 99871 4 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_codec_generic,snd_hda_intel
evdev 10629 19
lirc_dev 11391 1 ir_lirc_codec
ir_rc6_decoder 3561 0
ir_nec_decoder 3113 0
ir_sanyo_decoder 2861 0
ir_rc5_decoder 2473 0
ir_sony_decoder 2379 0
ir_mce_kbd_decoder 4822 0
ir_jvc_decoder 2601 0
drm 237667 4 ttm,drm_kms_helper,nouveau
r8169 58423 0
hp_accel 16520 0
kvm 404172 1 kvm_intel
rc_rc6_mce 1380 0
mac_hid 3305 0
ene_ir 14142 0
serio_raw 4977 0
lpc_ich 13368 0
jmb38x_ms 11144 0
lis3lv02d 11251 1 hp_accel
rc_core 16731 12 lirc_dev,ir_lirc_codec,ir_rc5_decoder,ir_nec_decoder,ir_sony_decoder,ene_ir,ir_mce_kbd_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_sanyo_decoder,rc_rc6_mce
hwmon 3057 2 coretemp,nouveau
memstick 7504 1 jmb38x_ms
mii 4027 1 r8169
crc32c_intel 14185 0
input_polldev 2818 1 lis3lv02d
i2c_i801 11269 0
i2c_algo_bit 5391 1 nouveau
i2c_core 24824 6 drm,i2c_i801,drm_kms_helper,i2c_algo_bit,nouveau,videodev
i7core_edac 17669 0
edac_core 44694 1 i7core_edac
microcode 16837 0
ac 3334 0
snd_hwdep 6332 1 snd_hda_codec
snd_pcm 79815 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_timer 18718 1 snd_pcm
pcspkr 2027 0
snd 59286 8 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_idt,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
soundcore 5418 1 snd
psmouse 88854 0
shpchp 25393 0
wmi 8251 3 hp_wmi,mxm_wmi,nouveau
video 11705 1 nouveau
thermal 8556 0
battery 7533 0
button 4477 1 nouveau
acpi_cpufreq 9818 1
processor 24385 1 acpi_cpufreq
ext4 481838 2
crc16 1359 2 ext4,bluetooth
mbcache 6074 1 ext4
jbd2 82704 1 ext4
usb_storage 48231 1
hid_microsoft 3202 0
usbhid 40577 0
hid 91094 3 hid_generic,hid_microsoft,usbhid
sd_mod 36882 5
sr_mod 14930 0
crc_t10dif 1039 1 sd_mod
cdrom 34880 1 sr_mod
crct10dif_common 1372 1 crc_t10dif
atkbd 16806 0
libps2 4187 2 atkbd,psmouse
ahci 23627 2
libahci 21484 1 ahci
libata 172264 2 ahci,libahci
sdhci_pci 12219 0
sdhci 28916 1 sdhci_pci
firewire_ohci 31781 0
ehci_pci 3928 0
led_class 3547 2 sdhci,hp_accel
scsi_mod 134432 4 usb_storage,libata,sd_mod,sr_mod
ehci_hcd 64491 1 ehci_pci
firewire_core 52100 1 firewire_ohci
mmc_core 95529 2 sdhci,sdhci_pci
crc_itu_t 1363 1 firewire_core
usbcore 182430 6 btusb,uvcvideo,usb_storage,ehci_hcd,ehci_pci,usbhid
usb_common 1648 1 usbcore
i8042 12950 1 libps2
serio 10721 6 serio_raw,atkbd,i8042,psmouse
And the output from lspci -v for Ethernet controller is:
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 3659
Flags: bus master, fast devsel, latency 0, IRQ 46
I/O ports at 5000 [size=256]
Memory at d4104000 (64-bit, prefetchable) [size=4K]
Memory at d4100000 (64-bit, prefetchable) [size=16K]
Expansion ROM at d4110000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
I find it odd that this is happening to me on arch linux only. My windows 8 is fine (I have a dual boot) and even when I used Manjaro over the course of a couple of months, which is based on arch, it worked fine for me. I was using wicd on Manjaro and am thinking of using that next time for arch. It is also important to remember that it's not only my wireless that's not working, neither is my wired connection.
Any help would be appreciated. I have no idea what to do to fix it and can not find any reports of similar problems happening to anyone else. I really want to get back to linux. My productivity has dropped alot since I have been using Windows 8. If you need me to post the output of any commands just say and I will do so. Once again thank you for any help.

Haha yea I'm sure.
Yea I know but I could never get it to work. Then again I haven't used wired on arch before.
Sure it's:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DMI [8086:d132] (rev 11)
00:03.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express Root Port 1 [8086:d138] (rev 11)
00:08.0 System peripheral [0880]: Intel Corporation Core Processor System Management Registers [8086:d155] (rev 11)
00:08.1 System peripheral [0880]: Intel Corporation Core Processor Semaphore and Scratchpad Registers [8086:d156] (rev 11)
00:08.2 System peripheral [0880]: Intel Corporation Core Processor System Control and Status Registers [8086:d157] (rev 11)
00:08.3 System peripheral [0880]: Intel Corporation Core Processor Miscellaneous Registers [8086:d158] (rev 11)
00:10.0 System peripheral [0880]: Intel Corporation Core Processor QPI Link [8086:d150] (rev 11)
00:10.1 System peripheral [0880]: Intel Corporation Core Processor QPI Routing and Protocol Registers [8086:d151] (rev 11)
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05)
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 05)
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05)
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 [8086:3b44] (rev 05)
00:1c.3 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 [8086:3b48] (rev 05)
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 [8086:3b4a] (rev 05)
00:1c.7 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 8 [8086:3b50] (rev 05)
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a5)
00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b03] (rev 05)
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b2f] (rev 05)
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05)
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT216M [GeForce GT 230M] [10de:0a28] (rev a2)
01:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio Controller [10de:0be2] (rev a1)
02:00.0 Network controller [0280]: Broadcom Corporation BCM43225 802.11b/g/n [14e4:4357] (rev 01)
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
04:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7160 [1131:7160] (rev 03)
05:00.0 FireWire (IEEE 1394) [0c00]: JMicron Technology Corp. IEEE 1394 Host Controller [197b:2380]
05:00.1 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2382]
05:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2381]
05:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2383]
05:00.4 System peripheral [0880]: JMicron Technology Corp. xD Host Controller [197b:2384]
ff:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers [8086:2c52] (rev 04)
ff:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2c81] (rev 04)
ff:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2c90] (rev 04)
ff:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2c91] (rev 04)
ff:03.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller [8086:2c98] (rev 04)
ff:03.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder [8086:2c99] (rev 04)
ff:03.4 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Test Registers [8086:2c9c] (rev 04)
ff:04.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers [8086:2ca0] (rev 04)
ff:04.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers [8086:2ca1] (rev 04)
ff:04.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers [8086:2ca2] (rev 04)
ff:04.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers [8086:2ca3] (rev 04)
ff:05.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers [8086:2ca8] (rev 04)
ff:05.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers [8086:2ca9] (rev 04)
ff:05.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers [8086:2caa] (rev 04)
ff:05.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers [8086:2cab] (rev 04)

No CFP interface shows in the N7K

Recently we installed a N7K-M202CF-22L card in the Nexus 7010 switch.
The card seems to be good but we cannot find any CFP port by use the command "show int status"
The software version is 6.1(1).
Any body knows what's wrong with it ?
The attached is the output of the follow command.
1) show int status
2) show inventory
3) show version module 2 epld
Does the card need special configuration?

Hi Sol72,
I'm sorry you're having this problem, but I have a few things that should be able to help you. One advantage in using the iPhone with your printer is the availability of the AirPrint feature that will let you print from the phone without needing the ePrint app. You can find information about using AirPrint with our printers here.
Let me know if this helps, or if you're still having problems printing from your iPhone.
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Interface shows only Sources Panel. How to show the Target & Map Panels

Someone must have hit some keys to hide the Target and Map panels in the Interface so that when I create a new interface, all I see in the Diagram tab is the Sources Panel. Does any one know how I can restore the other two panels?
Thanks.

Any suggestions ???

WDClientUser interface showing error

Hi SDNs,
I have done a program to know the number of users logged in a portal.
The coding i have written is
i have created a a "AbstractPortalComponent".
The coding i have written is :-
In my doContent method.
IWDClientUser currentUsers[] = WDClientUser.getClientUsers();
response.write("Number of logged in users are "+currentUsers.length);
<h6>error i am getting when i run it is the below.</h6>
Portal Runtime Error
An exception occurred while processing a request for :
iView : gettinglogonid.lok
Component Name : gettinglogonid.lok
com/sap/tc/webdynpro/services/sal/um/api/WDClientUser.
Exception id: 09:42_12/02/08_0005_2739150
See the details for the exception ID in the log file

Hi,
Please check the latest log file for the error.
Drive:/usr/sap/sID\JCXX/j2ee/cluster/server0/log/defaultTrace.X.trc
Regards,
Harini S

Show interface - received broadcast - counter - Vlan - L2 mcast

HI All,
I have a situation where the Show interface on 7609 displays broadcast counters. I did capture wireshark but did not see any broadcast. Wireshark broadcast for 1 minute shows 20 broadcast packets where as Vlan interface shows increase at rate of 1000 per minute.
L2 Switched: ucast: 8529 pkt, 896149 bytes - mcast: 35427 pkt, 2338134 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
40978 packets input, 2996897 bytes, 0 no buffer
Received 35607 broadcasts (0 IP multicasts)
The doubt I have is that I am running HSRP on LAN with 5 groups and 300ms hello. This makes around 1000 hello packets per second. The L2 multicast counter also increases at almost same rate of 1000 packets per second . The received broadcast and L2 mcast counters are almost same.
Is it likely that the received broadcast also includes the HSRP hello packets destined for 224.0.0.2? but it does shows(0 IP multicast).
Can someone please confirm that the received broadcast counter includes multicast HSRP packets or is it just a coincidence. But again on wireshark I dont see 1000 broadcast packets only HSRP packets in addition to unicast traffic.
Any help or Cisco link that can prove this will also help.
Thanks
M

Found the answer.
Anatomy of RX packet counters on a Cisco Nexus 5548:
Nexus5548# show int eth1/29
RX
6387682660 unicast packets 1495485 multicast packets 164 broadcast packets
6389178309 input packets 589693485138 bytes
5146969 jumbo packets 0 storm suppression bytes
* "input" = unicast + multicast + broadcast (all non-jumbo)
* "jumbo" = frames sized 1519 bytes to the MTU bytes defined on the interface
* "jumbo" frames are counted separately from non-jumbo ("input")
* (unicast, multicast and broadcast "jumbo" frames appear to be rolled into the
one "jumbo" counter)
This can be seen another way with the 'count detail' command, correlated to "show int" output:
Nexus5548# show int eth1/29 count detailed
Ethernet1/29
Rx Packets: 6389178309 <-- input
Rx Unicast Packets: 6387682660 <-- unicast
Rx Multicast Packets: 1495485 <-- multicast
Rx Broadcast Packets: 164 <-- broadcast
Rx Jumbo Packets: 5146969 <-- jumbo
Rx Bytes: 589693485138
Rx Packets from 0 to 64 bytes: 1059418 <-- non-jumbo start
Rx Packets from 65 to 127 bytes: 6072007478 +
Rx Packets from 128 to 255 bytes: 11055520 +
Rx Packets from 256 to 511 bytes: 287107435 +
Rx Packets from 512 to 1023 bytes: 12801466 +
Rx Packets from 1024 to 1518 bytes: 23 <-- non-jumbo end
Rx Trunk Packets: 6387682823 <-- unicast + broadcast
fyi.

GetNetworkInterfaces() missing some interfaces

Hi there,
I want to retrieve a list of installed network interfaces and I am using:
        try
            Enumeration<NetworkInterface> nifs = NetworkInterface.getNetworkInterfaces();
            while (nifs.hasMoreElements())
                NetworkInterface nif = nifs.nextElement();
                System.out.println("Interface: " + nif.getName());
        catch (SocketException ex)
            Logger.getLogger(Net.class.getName()).log(Level.WARNING, null, ex);
        }The problem is, that it does not show all interfaces - this is what it shows:
wlan0
lo(I am currently connected via WLAN)
and here is the correct list (output of "ifconfig -a"):
eth2      Link encap:Ethernet HWaddr 00:23:ae:2d:78:f3
          UP BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
          Interrupt:16
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:63292 errors:0 dropped:0 overruns:0 frame:0
          TX packets:63292 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5388083 (5.3 MB) TX bytes:5388083 (5.3 MB)
vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00
          BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0     Link encap:Ethernet HWaddr 00:22:fb:52:22:68
          inet addr:10.0.0.4 Bcast:10.0.0.255 Mask:255.255.255.0
          inet6 addr: fe80::222:fbff:fe52:2268/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:139968 errors:0 dropped:0 overruns:0 frame:0
          TX packets:115120 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:119590540 (119.5 MB) TX bytes:26182224 (26.1 MB)
wmaster0 Link encap:UNSPEC HWaddr 00-22-FB-52-22-68-35-32-00-00-00-00-00-00-00-00
          UP RUNNING MTU:0 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)If you now wonder why there is an eth2 but not eth0 this could be because there was a network card that got removed (a good while ago). Why the hack are the others not available in the enumeration of network interfaces? I am using Sun JDK 1.6 update 20:
java -version
java version "1.6.0_20"
Java(TM) SE Runtime Environment (build 1.6.0_20-b02)
Java HotSpot(TM) Server VM (build 16.3-b01, mixed mode)

I have made several tests and found out that: As soon as I plug in a cable to the interface eth2 then it is recognized. Even if I then plug it off. After reboot it is again not showing up any more.
I am using Ubuntu 9.10 - is it possible that there is an issue with the sun Java runtime on Linux/Ubuntu?
Tried it with the OpenJDK - no, same issue here.
It is really a headache and I already searched the internet - samples to retrieve the interfaces are always basically the same and nobody writes that only interfaces are reported by getNetworkInterfaces() that are up (or have been up recently).
I tested also with the virtualbox - as soon as I start one of the virtual machines the interface shows up.
I started to think it could be an issue of the single machine... - tested on a different machine with very slightly different hardware on Ubuntu 10.04 - same issue here!
I tested on a Windows 2003 machine - there it seems to work even for interfaces that are not up.
Finally tested on Windows 7 and guess what: Even ipconfig /all does not show all interfaces - super crap!
WUUAAHH!
I think I must give up on getting the list of network interfaces in a reliable and platform independent way as even calling the OS specific tools Windows 7 fools me...

Catalyst 2950 interface problem

Hi, Sirs.
My Catalyst 2950-24 (IOS Ver 12.1.22EA7)stops communicate with an other switch port of a Catalyst 3512XL-EN after catalyst 2950 powered on 1 or 2 days.
th show interface shows that 2476498 ignored.
FastEthernet0/1 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 000d.28c0.cf41 (bia 000d.28c0.cf41)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 100BaseTX
input flow-control is unsupported output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 3d19h, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 28000 bits/sec, 44 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
10033048 packets input, 806430104 bytes, 2476489 no buffer
Received 10031591 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 2476498 ignored
0 watchdog, 2217265 multicast, 0 pause input
0 input packets with dribble condition detected
357799 packets output, 25835259 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
what does is mean?

Hello,
what other switches do you have in your network ? If you have just the 2950 and the 3500, make sure that the 2950 is the root switch for all your VLANs, by configuring the global command:
spanning-tree vlan x priority 0
Also, check the log on the 2950 for the following message:
SCHAN ERROR INTR: SRC=6 DST=5 OPCODE=20 ERRCODE=5
If you see those, chances are that you have a faulty unit. Here is the relevant bug info:
CSCdv83336 Bug Details
Under certain level of traffic load, the (2950) switch will start logging the following messages on the console:
SCHAN ERROR INTR: SRC=6 DST=5 OPCODE=20 ERRCODE=5
and after a few seconds, the switch will stop passing any traffic. In some cases, the switch seemed still forwarding broadcast and multicast traffic, which will cause STP problem if the switch has redundant link and is not supposed to be the root for the VLAN, as both port will go forwarding.
The same error message has been identified in CSCdu87836.
An assessment of the impact
Unit stops passing any traffic.
WORKAROUND
Several units were returned by CISCO. The units were re-screened to the latest test program, and failed the SDRAM memory test.
Customer should RMA unit back to Cisco
Regards,
Nethelper

Full Duplex Collisions???

OK Im really confused. I thought you couldnt have collisions with a full duplex port but yet my switches are showing collisions even though they are set to full. Also I was told that some applications will not run right if the network cards are set to full duplex. Has anyone ever run into this?

William
Part of the definition of full duplex is that the collision detection mechanism is disabled on a full duplex port/interface. So I believe it is impossible to have collisions on a port that is configured as full duplex - other than the possible result of some bug in the code.
Is it possible that the interface counters recorded collisions at some point in the past when the port was half duplex?
I have not run into any situation where an application would not run on a port set to full duplex. And I wonder how the application would know. One of the advantages of the layered model is that the upper layers are insulated from dependencies on what happens at lower layers. How would an application know whether the port was half duplex or full duplex?
HTH
Rick

Creative Cloud App just showing blank white box! Cannot install Photoshop

I'm trying to install a Photoshop trial - have followed instructions to install the CC app. The icon appears on my desktop and a Creative Cloud folder appears in my Explorer folder but when I click on the CC app, all I see is a white box.
Occasionally, I have managed to get list of apps to show - but when I click on the "Try" button next to Photoshop, again it goes to a blank white box. Can't do anything! No spinning icon showing that something is loading - just blank white.
Very frustrating. Just want to download the trial so I can decide if I want to buy. Am on Windows 8 (64 bit). Have tried uninstalling and re-installing using a different browser (Firefox & Chrome) but still same result.
Please help!!
Thank you,

Hi again Jeff - I just read on a similar thread that another user had the same issue with blank CC app and realised the problem was her username having an ampersand "&"
I have an ampersand also in my username on the computer - do you think this might be affecting the issue?
She gave instructions for changing the username (although the link is for Win 7 and I'm using Win 8) - but I'm nervous about changing big system things like that. What happens to "permissions" on certain folders - am I likely to be locked out of making changes in certain folders?
Here is what she wrote on that thread:
If you have ampersand (&) or other non-alphabet characters in windows user folder name (Example: C:\Users\Bob & Mary), then Flash Builder will fail to install (happened to me), Creative Cloud will display white screen, and/or other miscellaneous problems.
I confirmed this to be true and works:
1) I had blank Creative Cloud window as shown in the first post.
2) I renamed the display username and window user folder name by doing the instructions here:
http://www.ghacks.net/2011/03/28/how-to-change-a-windows-account-name-and-user-profile-fol der-name/
(Example: Change from "Bob & Mary" to "Bob n Mary" - without the quotes)
3) After logging back in my newly renamed account, I opened Creative Cloud and login interface shows up! :-)
I would prefer not to do this if you have another suggestion? But just thought I'd mention this as well to see what you thought.
I have also since tried uninstally CC, deleting both the OOBE folder and the AAMUpdater folder, then re-installing CC again... same result. I always get to the list of Apps fine but the minute I click on the "Try" button next to Photoshop, the whole App window goes to a blank white screen and freezes.
Thank you.

On Interface show collisions?

Similar Messages

Maybe you are looking for