On running labview cannot find Scaling & mapping or Amp & level measurement VI's

I am trying to run through the exercises in the getting started book, and in the first few pages it is asking for VI's that I can not find. Using a 1600, 1100 in the 1000 slot chassis. I used all the five disks when installing the software.
Did I miss something?

As explained in the on-line help for those functions, they are not available in the base version of LabVIEW. Check to see which version you have.

Similar Messages

P67-C43 "cannot find required map name"

Hello
Specs:
P67-C43
RAM: Gskill DDR3 1333 8GB
Video card: 4870 XFX 1GB
PSU: Antec 620W
CPU: i5 2500k @ stock 3.3ghz
DVD drive: Sony (don't know exactly)
HD: 1TB Samsung
& A Hyper 212+
I'm getting this message
EFI Shell version 2.00[4.640]
Current running mode 1.1.2
map: cannot find required map name.
Press ESC in _ seconds to skip startup.nsh, any other key to continue.
Shell>
I don't get that message when I take out or put in a new stick of RAM. Instead, I can go the BIOS and change settings or load default settings. If I choose default settings/boot then I get the message.
Any help please. Please don't tell me it's DOA :(

Quote from: petersonx on 14-May-11, 23:52:55
I don't get that message when I take out or put in a new stick of RAM. Instead, I can go the BIOS and change settings or load default settings. If I choose default settings/boot then I get the message.
Can you further explain on this part?
Do you already have an OS installed to the system? If you do, does the message pops up when you do the OS installation?

MSI Z77A-GD65 Cannot Find Required Map Name

Hello, I am trying to do my first build ever and ran into an error with the MSI 7ZZA-GD65 motherboard. I tried to do a build outside of the case to make sure everything was running and I got an error when booting up my system. It states.
EFI Shell version 2.31 [4.6530
Current running mode 1.1.2
map: cannot find required map name.
Press esc in 1 seconds to skip startup.nsh, any other key to continue.
Shell> _
There isn't much plugged into the board right now I have.
CPU: Intel i5-3570k
RAM: 1 stick Billistix in slot DIMM 1
GPU: Asus Gtx 660ti
PSU: Seasonic M12 II 620w Bronze
I couldn't find anyone else getting the error so I posted here. Please help if you can.

Quote
RAM: 1 stick Billistix in slot DIMM 1
Is that the second slot from the CPU ? If not, then insert it into that second slot. Afterwards do a full CMOS clear, and then retest.
Also remove that GPU card for now and test with only the onboard graphics.

Cannot find the maps stored in import manager during port creation

Hi All,
I am unable to find any maps that i saved in import manager during port creation ,the maps are not showing in dropdown list during port creation in console.Do i need to store the maps that i have in import manager in specific place under mdm server,so that i can see them during port creation.
All i need to do is assign my import map during inbound port creation,but i cannot find any maps in console.
Could I know whether i am storing my maps some where other than default location.
Thanks
Aravind

Hi Aravind,
First of all check the remote system assigned to ur Port. After that go to import manager. When u logon to the import manager, u get a window "Connect to source". Mention the same remote system over there.Select the file type.Browse the file and map the fields,values,field matching and save the map. then unload the repo and assign the map to the port.
Second way is, u create the port first and give any particular remote system to it. Put the file (u want to use for mapping) in the ready folder of that port and in connect to source window select the type as port, remote system(ame as used port port) and port.then map and save. unload the repo and assign the map to port. Ready folder will be in ur server at location: C drive or D drive->SAP MDM 5.5 ->server->distributions->repo name->inbound->port code->ready. For this option, Ur port type should be manual. After assigning the map u can change it to automatic or keep it manual as per ur requirement.
Hope this solves ur problem.
Regards,
Dheeraj.
Edited by: Dheeraj Kumar on May 6, 2008 9:16 AM

Cannot run project - Cannot find config file bc4j.xcfg (9.0.5.2)

Hi all,
I've gotten myself in a situation and can't find my way out. I've got a project that does not use any business components. Just as a test, I created a business component (View Object, I think - can't remember for sure), and then deleted it and another file or two associated with the object shortly thereafter. Now, whenever I try to run the project (F11), I get the following error:
oracle.jbo.JboException: JBO-33001: Cannot find the configuration file /com/my/package/datamodel/common/bc4j.xcfg in the classpath
     at oracle.jbo.client.Configuration.loadFromClassPath(Configuration.java:345)
     at oracle.jbo.common.ampool.PoolMgr.createPool(PoolMgr.java:272)
     at oracle.jbo.common.ampool.PoolMgr.findPool(PoolMgr.java:473)
     at oracle.jbo.common.ampool.ContextPoolManager.findPool(ContextPoolManager.java:165)
     at oracle.adf.model.bc4j.DataControlFactoryImpl.findOrCreateSessionCookie(DataControlFactoryImpl.java:135)
     at oracle.adf.model.bc4j.DataControlFactoryImpl.createSession(DataControlFactoryImpl.java:220)
     at oracle.adf.model.bc4j.DataControlFactoryImpl.createSession(DataControlFactoryImpl.java:97)
     at oracle.jbo.uicli.mom.JUMetaObjectManager.loadCpx(JUMetaObjectManager.java:612)
     at oracle.adf.model.servlet.ADFBindingFilter.initializeBindingContext(ADFBindingFilter.java:328)
     at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:173)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:600)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:317)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:790)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].server.http.HttpRequestHandler.run(HttpRequestHandler.java:270)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].server.http.HttpRequestHandler.run(HttpRequestHandler.java:112)
     at com.evermind[Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)].util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:192)
     at java.lang.Thread.run(Thread.java:534)
I am assuming the error is related to the business object that is no longer there. My guess is that there is some reference somewhere that is telling JDev that there are business components associated with this project. I just can't find where that reference is (or my assumption is wrong ;) ).
Does my project need the bc4j.xcfg file if it does not use any business components? Can anyone provide any guidance?
Thanks for any help,
Andy

Thanks for the reply. I looked at the link supplied but didn't see how that could help me. Could you provide a little detail regarding what I need to do or where I need to look?
And I want to make clear that I do not have and do not want any ADF components in my project at this time. I am simply looking to get my non-ADF project running locally as it used to do before I added and then deleted a component.
Thanks,
Andy

Calling web service from MBean weblogic cannot find type mapping file

When calling web service from custom MBean i get java.io.IOException.
java.io.IOException: unable to find the type mapping resource file for:
net.msl.sfx.ebooking.client.BookingPartiesServiceService
at weblogic.webservice.core.encoding.DefaultRegistry.<init>(DefaultRegis
try.java:67)
at weblogic.webservice.core.rpc.ServiceImpl.<init>(ServiceImpl.java:83)
at net.msl.sfx.ebooking.client.BookingPartiesServiceService_Impl.<init>(
BookingPartiesServiceService_Impl.java:22)
at net.msl.sfx.ebooking.service.EBookingService.getBookingParties(EBooki
ngService.java:59)
The types.xml file is placed in same jar file as the classes such as net.msl.sfx.ebooking.client.BookingPartiesServiceService_Impl.
When calling the same class/method from a EJB, everything works fine and the web service is called.

i am having the same problem.
Do you have a solution now?
Thanks

Cannot find intf mapping in interface determination

Hi all,
I have these bpm steps 1. Trasnformation followed by send sync. i am trying to do a receiver JDBC sync call to oracle db.
1. in my transformation i have my:
1. Request message : messageA mapped to
2.Response message JDBC request and in my sync send step i have specifed,
1.Request Message : JDBC Request
2. Response Message :JDBC response
I have the following MI defined:
1. Abstract Async - Message A
2. Abstract Async - JDBC Request
3. Abstract Async - JDBC Response
4. Abstract Sync - JDBC Request
- JDBC Response
in my ID , when i configure for my interface determination, i cannot slect my inbound interface nor my interface mapping...It says no object found!
Although i activated them in my IR. I did Cache refresh,SLD cache..No Luck
Pls advice

Hi,
>in my ID , when i configure for my interface determination, i cannot slect my inbound interface nor my interface mapping...It says no object found!
Are you using a Business Service for your JDBC? if yes, did you assign the Message Interface to the Inbound of your Business Service.
As you are doing the transformation inside the BPM, there will be no need to select the Interface Mappuing in Interface Determinaytion.
Also, in your Intefrace/ Receiver Determination, the Sender message Interface will be 4. Abstract Sync - JDBC Request - JDBC Response . You also should have created an Inbound Synch Message Interace with JDBC request and JDBC Response and this should have been assigned to the Inbound Message Interface of your JDBC service.
Regards,
Bhavesh

I cannot get Firefox to come up. It says it is running but cannot find it. I have uninstalled and reinstalled. Please help.

When I try to bring Firefox up it does not show that it is. If I shut my computer down it will come up the first time and as long as I leave it open it is okay. When I log out it does not come back up the next time. I am not having trouble with Chrome or Explorer.

The Firefox Home app for iOS is not the Firefox browser but rather for to synce with your desktop Firefox to have your Firefox desktop history, bookmarks and open tabs on your iPhone/iPad.
http://www.mozilla.org/en-US/mobile/home/
http://www.mozilla.org/en-US/mobile/home/faq/
https://wiki.mozilla.org/Mobile/Platforms#Other_Platforms
iPhone/iPad/iPod
We have no plans to release the full Firefox browser for iOS. The iOS SDK agreement requires apps to use Apple's own JavaScript engine (or none at all, like Opera Mini which downloads pre-rendered pages from Opera's servers and cannot run JavaScript code in the client). Because of this, we have no supported way to distribute Firefox's rendering and JavaScript engine to iPhone users.

I cannot access firefox because it says it is already running. It is asking me to close the program that is running I cannot find where it is. I uninstalled and reinstalled the latest version. It did not correct the problem

when I click the firefox link a window pops up saying a the program is already running and I must close that program in order to run a current one. I went through task manager and then completly uninstalled firefox and reinstalled the newest version. This did not help.

See this article for possible causes and solutions:
[[Firefox is already running but is not responding]]
See also:
http://kb.mozillazine.org/Profile_in_use

Startup class cannot find a config file.

I have written a startup class to configure log4j in Weblogic.
The class runs but cannot find the configuration file. The
code for the startup class is as follows....
package com.n2bb.ams.common.util;
import java.io.FileInputStream;
import java.io.File;
import java.io.IOException;
import java.net.URL;
import java.util.Properties;
import com.n2bb.ams.common.util.FileLocator;
import org.apache.log4j.xml.DOMConfigurator;
* Insert the type's description here.
* Creation date: (12/5/00 11:12:13 AM)
* @author: Administrator
public class ApplicationStartUp implements weblogic.common.T3StartupDef {
 * ApplicationStartUp constructor comment.
 public ApplicationStartUp() {
 super();
 * setServices method comment.
 public void setServices(weblogic.common.T3ServicesDef arg1) {
 * startup method comment.
 public String startup(String arg1, java.util.Hashtable arg2) throws Exception {
 String resource = null;
 try {
 resource = (String) arg2.get("configFileName");
 System.out.println("ConfigFileName: " + resource);
 URL configFileResource = ApplicationStartUp.class.getResource(resource);
 System.out.println("configFileResource: " + configFileResource.toString());
 String file = configFileResource.getFile();
 DOMConfigurator.configure(file);
 return "Log4j configuration initialized completed.";
 } catch (Exception e) {
 System.out.println("Cannot open config file: " + resource);
 return "Log4j configuration failed to initialized.";
The section of the config.xml the calls my startup class looks
like....
<StartupClass
Arguments="configFileName=/bea/user_projects/mydomain/log4j-config.xml"
ClassName="com.n2bb.ams.common.util.ApplicationStartUp"
Name="AMS Startup Class" Targets="myserver"/>
I have tested the code in a standalone class and it works fine.
Why can't I find the log4j-config.xml file? Any help would be
greatly appreciated.

Wow, your system must have a long history of having picked up assorted bad stuff ...
You have CleanMyMac2, which should definitely be removed.
You have other stuff (MacCleanse, for example) that I don't have first-hand knowledge about but should very likely be removed.
You are using Google Chrome which is a resource hog.
Further, your Adobe Flash player is not current.
If I had all these issues, I would do a clean install of Yosemite and only reintroduce the essential stuff.
You can search for the .plist files by opening finder, holding down the Option key, and doing Go > Library from Finder's menu and then searching for the file(s).

How to find the mapping between External Object Name and Business Obj.

Hello Gurus
Anyone who can help me? I would like to know is there any way to know Business Object is behind object associated to Context Node, it seems that for some cases is easy but for instance for object BuilHeader is not the case, at least for me. View BP_ADDR/StandardAddress, which belongs to UI Component BP_ADDR, has context node HEADER which is associated to BuilHeader. In case to enhance that object (to add new attributes), using EEWB, I need to know what is the business object behind that external name. Somehow I cannot find the mapping between external name BuilHeader and Business Object.
Kind regards
Aleksandar

Hi Aleks,
If you want to enhance Business Partner, the object you are looking at should be "BUPA" in EEWB. To my knowledge, there is no place where this kind of mapping is maintained.
Note 484597 describes where to find the Cookbook which describes the enhanceable objects and the enhancement process.
In case your requirement is to add table attributes, you can also take a look at the wiki link:
http://wiki.sdn.sap.com/wiki/display/CRM/EEWB-AddingTableattribute
Regards,
Nisha

Lost files now cannot start firefox, told it is already running and cannot stop it.How can I reinstall while process is still running?

I may have deleted files that had firefox running. Cannot find them, they may have been duplicates. When trying to start firefox got message telling me firefox was already running and had to stop the process or restart pc. Tried that numerous times with no result.
Deleted and reinstall firefox several times and same thing happened.

You may have deleted the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder] 
Use the Firefox profile manager to create a new profile.
See:
* http://kb.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows
* http://kb.mozillazine.org/Recovering_a_missing_profile
* http://kb.mozillazine.org/Profile_in_use

Computer with labview runtime engine (v8.2) cannot find sub-VI NI_AALBase.lvlib:Mean.vi. What do I have to do?

I am trying to run an exectutable on a computer that has the labview v8.2 runtime engine. The error I am getting is: Cannot find sub-VI NI_AALBase.lvlib:Mean.vi. What is the easiest solution?

the matrix,
I would try reinstalling the LabVIEW 8.2 Run-Time Engine. You may also want to try creating a very simple project in your development environment that has a VI with just the Mean.vi, try building an executable and then running it on the machine that just has the 8.2 RTE.
Doug M
Applications Engineer
National Instruments
For those unfamiliar with NBC's The Office, my icon is NOT a picture of me

Since I uploaded the new OS X Mavericks the App Store, Messages, Notes, Calendar, Maps and Preview will not launch/open. In Finder cannot find my files. Most crucially cannot upgrade OS X Mavericks software. I had two apple ID's, the old one not used

Since I uploaded the new OS X Mavericks the App Store, Messages, Notes, Calendar, Maps and Preview will not launch/open. In Finder cannot find my files. Most crucially cannot upgrade OS X Mavericks software. I had two apple ID's, the old one not used

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

I need to reinstall my Canon Pixma Pro 9500 MK 2 printer on my iMac running Mavericks. It looks for software but Apple cannot find. The driver is available on my computer. Is there a way I can force the installer to use the available driver?

On running labview cannot find Scaling & mapping or Amp & level measurement VI's

Similar Messages

Maybe you are looking for