On startup of Mac Mini running OS Mavericks login windows are invisible. Login is possible but there are no white boxes for username and password. Keyboard inputs also do not display.
Mac Mini with 2 Ghz Intel Core i7 running OS X 10.9.1. Recent problem with startup screen where I get a gray startup screen that is blank and does not show the login windows for username or password. Mousing over where they should be does provide a cursor change and I can click into the invisible window and login. Also, I can just type the information and hit enter and login without problems but the keystrokes do not appear either. This is not a big problem if I make sure that I type my login information correctly, but if I make a mistake it can be difficult make sure I am in the right place before I retype. Any ideas why the screen is just gray and does not show the windows? Once I type in the login info in the invisible windows and hit enter the computer starts up, loads finder, and runs without any other noticeable problems.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.
Similar Messages
-
Why does my Mac Mini running on Mavericks so slow to start and load apps?
Why does my Mac Mini running on Mavericks take so long to start and load apps?
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,[lps]*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}* .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D23 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Fan noise/overheating issue? I have a late 2008, 15'' MBP and I'm having a lot of fan noise while just running safari. I don't think this is normal but perhaps it is? Thanks for any and all help!
Runaway applications can increase fan activity
-
Startup asks for Username and Password - which we don't have
Our iMac G4 hard disk has failed and we've re-installed the Mac OX 4 system into our external drive. After installation the startup process asks for a username and password. We have never had to use a username and password on this computer and have no way of accessing what they could be. This means we cannot go any further and have to either shutdown or restart the computer (which just takes us back to username and password again). How do we circumvent this username and password?
It is presumably asking you to create a username and password so that it can make an admin account with them. There has to be at least one admin account: once you've got it up and running you can set it to auto-log in so that you don't need to enter the details every time you boot up. The previous installation must have had an admin account with a username and password, it's just that if it was set to auto-log-in you would only need it when installing new software. The new account doesn't have to have the same name as the old one, just invent something convenient: the username should be one word and lower-case.
-
APEX is running. I'm at the login page. Now I can't remember my admin username and password
After hours upon hours of finding fixes to get Oracle Application Express running, I am now on the verge of finally getting the test environment setup. In the frustration, I have now forgotten my username and password that I had when I created the thing.
Help?
BTW, is my default workspace called "Internal?"login with sys account over installation folder..
e.g C:\apex>sqlplus
connect:sys/xe@xe as sysdba
SQL:>@apxchpwd
You can reset ADMIN password(e.g Apex_4.2) -
New Mac Mini Running Fine-Mavericks 10.9.5
I am an Apple convert from Microsoft. Giving up Windows after years of the gut wrenching abuse over the years of XP only to have Microsoft kill it. That being said and out of the way.
I find my old school computer self coming from the 4 color Amiga Desktop Icons and Apple color palette in yon days of old, only to find countless reviews about Yosemite's "eye candy" problem. Who cares? So far, in the reviews I am reading a bunch of Blah, blah typing. Know one has given or provided conditions in which they installed Yosemite and type of Mac, including, but not limited to, the compatibilty of the Apps they have installed. So, I am here instead of blogging on Apple's Yosemite review page.
I have a Late 2012 Mac Mini i5, 4 GB memory, 500 GB HD with 27" Thunderbolt Display. A LaCie 1 TB ext HD and a WD My Passport 1 TB ext HD. I'm using Boot Camp to dual boot Windows 7 Pro. I am running MS Office 2011 for Mac in Mavericks. I use Firefox as my secondary browser. I am running an HP 6520 Photosmart wireless printer. I have a Cisco E2500 router. I want to know if upgrading to Yosemite will cause more problems for me than to bite the bullet and clean install. How about, if my Mac is working, why fix it with an upgrade that I will not use. I don't have an iPhone. Do I wait until Apple forces me to install? By the way, how will it affect my 0 partition if I choose to revert back to Mavericks. What about driver functionality in Yosemite? Someone has got to feel my struggle. Thanks.jndupuis1 wrote:
I've only had this Mini since August. I have had to update Safari twice, apps once and OS X once. A bit excessive for being so new. ( Well, Microsoft was worse about updates ). You all are helpful in the support community. I'll quit reading reviews now and ask all of you the meat and potato questions.
You can expect an OS update from Apple every couple of months unless there's a truly nasty bug that Apple is trying to stamp out. Security updates come up as needed. The one nice thing about Apple updates is that I don't worry about them bricking my computer. Not saying it doesn't happen and I always plan for the worst but backing up one last time before applying the update, but I can't think of a Mac OS update that has been a disaster for my contingent of computers. Can't say the same for Windows updates.
There's a wealth of knowledge here at the ASC - the depth and breadth continues to amaze me and I've been hanging out here for a very long time. You'll find the same level of knowledge at many Linux sites but I've found those to be less forgiving of newbies than the ASC is. -
Problem description:
my mac is running very very slow
EtreCheck version: 2.1.8 (121)
Report generated 6 March 2015 20:11:31 GMT
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Technical Specifications)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 176
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.2 (14C109) - Time since boot: 8 days 8:37:49
Disk Information: ℹ️
Hitachi HTS545032B9A302 disk0 : (320.07 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Mum's Mac (disk1) / : 318.84 GB (130.72 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 319.21 GB Online
HL-DT-ST DVDRW GS31N
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.sony.driver.prs (1.0.1d1) [Click for support]
[not loaded] com.tomtom.driver.UsbEthernetGadget (1.0.0d1) [Click for support]
Startup Items: ℹ️
MobileBrServ: Path: /Library/StartupItems/MobileBrServ
Startup items are obsolete in OS X Yosemite
Problem System Launch Agents: ℹ️
[killed] com.apple.CallHistoryPluginHelper.plist
[killed] com.apple.CallHistorySyncHelper.plist
[killed] com.apple.cmfsyncagent.plist
[killed] com.apple.printtool.agent.plist
[killed] com.apple.telephonyutilities.callservicesd.plist
5 processes killed due to memory pressure
Problem System Launch Daemons: ℹ️
[killed] com.apple.AssetCacheLocatorService.plist
[killed] com.apple.awdd.plist
[killed] com.apple.ctkd.plist
[killed] com.apple.emond.aslmanager.plist
[killed] com.apple.ifdreader.plist
[killed] com.apple.installd.plist
[killed] com.apple.nehelper.plist
[killed] com.apple.nsurlsessiond.plist
[killed] com.apple.periodic-daily.plist
[killed] com.apple.periodic-weekly.plist
[killed] com.apple.tccd.system.plist
[killed] com.apple.wdhelper.plist
[killed] com.apple.xpc.smd.plist
[killed] org.cups.cupsd.plist
14 processes killed due to memory pressure
Launch Agents: ℹ️
[loaded] com.epson.esua.launcher.plist [Click for support]
[not loaded] com.sony.ReaderLibrary.RunReaderLibrary.plist [Click for support]
Launch Daemons: ℹ️
[failed] com.adobe.fpsaud.plist [Click for support] [Click for details]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Click for support]
[failed] com.apple.SafariBookmarksSyncer.plist
[loaded] com.google.keystone.agent.plist [Click for support]
User Login Items: ℹ️
MyDriveConnect Application (/Applications/MyDriveConnect.app)
iTunesHelper UNKNOWN Hidden (missing value)
Canon IJ Network Scanner Selector EX Application Hidden (/Applications/Canon Utilities/IJ Network Scanner Selector EX/Canon IJ Network Scanner Selector EX.app)
MyTomTomSA UNKNOWN Hidden (missing value)
TomTomHOMERunner Application Hidden (/Users/[redacted]/Library/Application Support/TomTom HOME/TomTomHOMERunner.app)
Google Drive Application (/Applications/Google Drive.app)
HP Product Research Application (/Library/Application Support/Hewlett-Packard/Customer Participation/HP Product Research.app)
HPEventHandler UNKNOWN (missing value)
HP Scheduler Application (/Library/Application Support/Hewlett-Packard/Software Update/HP Scheduler.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
EPPEX Plugin: Version: 3.0.5.0 [Click for support]
AdobePDFViewerNPAPI: Version: 10.1.13 [Click for support]
AdobePDFViewer: Version: 10.1.13 [Click for support]
Flash Player: Version: 16.0.0.305 - SDK 10.6 Cannot contact Adobe
Default Browser: Version: 600 - SDK 10.10
QuickTime Plugin: Version: 7.7.3
Easy-WebPrint EX: Version: 1.1.0 [Click for support]
Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Click for support]
iPhotoPhotocast: Version: 7.0 - SDK 10.8
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Volumes being backed up:
Mum's Mac: Disk size: 318.84 GB Disk used: 188.12 GB
Destinations:
My Passport [Local]
Total size: 319.91 GB
Total number of backups: 8
Oldest backup: 2013-04-28 13:07:45 +0000
Last backup: 2014-01-12 18:00:46 +0000
Size of backup disk: Too small
Backup size 319.91 GB < (Disk used 188.12 GB X 3)
Top Processes by CPU: ℹ️
2% WindowServer
2% hpdot4d
1% NotificationCenter
1% Google Drive
1% usernoted
Top Processes by Memory: ℹ️
155 MB com.apple.WebKit.WebContent
133 MB Google Chrome
99 MB Safari
99 MB Finder
60 MB WindowServer
Virtual Memory Information: ℹ️
91 MB Free RAM
1.48 GB Active RAM
1.39 GB Inactive RAM
1.11 GB Wired RAM
13.41 GB Page-ins
309 MB Page-outsWhen you see a beachball cursor or the slowness is especially bad, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting. -
Windows XP (Version 5.1, service pack 3)
Good morning Ajay,
The checkbox appears on the 4th screen when you use the "New Transformation Wizard" to create a function (directly under checkbox "Function is deterministic").
IMHO, whether the code is run in parallel or not depends on how the mapping is run; if parallel it would try to run the function in parallel as well (unless - I guess - you've altered the property of the function in the mapping which says it can only be run row-based).
HTH.
Regards, Patrick -
HP Pavilion 27xi Monitor: Display problem Mac Mini running Yosmite
Image quality is very poor for Mac Mini running Yosmite connected via HDMI.
Adjusting overscan helps scaling, but pixelation and poor image quality is not changed (very blurry)
Using VGA/mini display route with same devices, image quality if far better showing that somehow mini conncected to HP monitor via HDMI could be improved via driver update.
Is there a driver update for Yosmite?
Only drivers found were for Windows:
http://support.hp.com/us-en/product/HP-Pavilion-27-inch-Displays/7274719/model/5304250/drivers
Please help
This question was solved.
View Solution.Hello @adsben,
I understand that the image quality for your HP monitor is poor when connected to your Mac Mini, and I would be happy to assist you in this matter!
According to this document on using HP Monitors on a Mac:
"HP monitors are not supported in a Mac environment. However, newer Macs use graphics with VESA modes and can display to most HP LCD monitors. To do this, connect the monitor to the Mac while the Mac is off, and then turn on the MAC. The monitor should operate at 60Hz. The INF and software for the HP monitor are for Microsoft Windows and cannot be run in a standard MAC OS environment."
I hope this helps!
Best Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping! -
I'm using LR5.7 on a Mac Mini running Mavericks and when I attempt to import a folder of new RAW photos from my external drive into my catalog instead of seeing a preview of each thumbnail photo I see the following message displayed: "Preview Unavailable for this file." If I highlight any other folder of photos the previews are all there. What is the likely reason for these previews being unavailable? JohnnyCam
What camera took these RAW photos?
Did you use any Nikon software to transfer the photos to your computer's hard disk? -
I've updated my Mac Mini to OSX Mavericks and since then my computer has been running slow. I've gone through other threads and followed recommendations and still the issue persists. I ran EtreCheck and got the following:
Hardware Information:
Mac mini (Mid 2011)
Mac mini - model: Macmini5,1
1 2.3 GHz Intel Core i5 CPU: 2 cores
2 GB RAM
Video Information:
Intel HD Graphics 3000 - VRAM: 288 MB
System Software:
OS X 10.9.2 (13C64) - Uptime: 0 days 0:5:55
Disk Information:
APPLE HDD HTS547550A9E384 disk0 : (500.11 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
lj0k m k, p (disk0s2) / [Startup]: 499.25 GB (203.57 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
USB Information:
Apple, Inc. Keyboard Hub
Apple Inc. Apple Keyboard
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Logitech USB-PS/2 Optical Mouse
Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Kernel Extensions:
com.logmein.driver.LogMeInSoundDriver (1.0.3 - SDK 10.5)
Launch Daemons:
[System] com.adobe.fpsaud.plist 3rd-Party support link
[System] com.fitbit.galileod.plist 3rd-Party support link
[System] com.logmein.logmeinblanker.plist 3rd-Party support link
[System] com.logmein.logmeinserver.plist 3rd-Party support link
[System] com.logmein.raupdate.plist 3rd-Party support link
[System] com.teamviewer.teamviewer_service.plist 3rd-Party support link
Launch Agents:
[System] com.coupons.coupond.plist 3rd-Party support link
[System] com.teamviewer.teamviewer.plist 3rd-Party support link
[System] com.teamviewer.teamviewer_desktop.plist 3rd-Party support link
User Launch Agents:
[not loaded] com.google.keystone.agent.plist 3rd-Party support link
User Login Items:
iTunesHelper
SpeechSynthesisServer
Google Chrome
Internet Plug-ins:
JavaAppletPlugin: Version: 14.8.0 - SDK 10.9 Outdated! Update
FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
QuickTime Plugin: Version: 7.7.3
Flash Player: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
CouponPrinter-FireFox_v2: Version: 5.0.3 - SDK 10.6 3rd-Party support link
Default Browser: Version: 537 - SDK 10.9
Silverlight: Version: 4.0.50826.0 3rd-Party support link
iPhotoPhotocast: Version: 7.0
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins:
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
3rd Party Preference Panes:
Flash Player 3rd-Party support link
Perian 3rd-Party support link
Old Applications:
/Applications/iWork '09
None
Time Machine:
Skip System Files: NO
Auto backup: NO - Auto backup turned off
Time Machine not configured!
Top Processes by CPU:
3% WindowServer
1% EtreCheck
0% imagent
Top Processes by Memory:
49 MB mds_stores
43 MB ocspd
43 MB com.apple.IconServicesAgent
39 MB Dock
35 MB WindowServer
Virtual Memory Information:
493 MB Free RAM
651 MB Active RAM
203 MB Inactive RAM
700 MB Wired RAM
200 MB Page-ins
0 B Page-outs
Does anyone have any feedback on if there is anything that can be done to improve performance?
Thanks in advanceYou are only running on 2GB of RAM. I would suggest 4GB as a minimum, and if possible, maxing out the Mini. LogMeIn and TeamViewer have been culprits for some users in Mavericks, also.
Pete -
Not sure how to diagnose issues on my Mac, but I gathered I should run Etre and post results here. I know I could add more RAM, but this is so slow that I have to believe something else is going on. Can someone spot anything unusual in the following?
Problem description:
Mac Mini running very slow
EtreCheck version: 2.1.6 (109)
Report generated January 24, 2015 11:33:17 AM EST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
Mac mini (Mid 2011) (Technical Specifications)
Mac mini - model: Macmini5,1
1 2.3 GHz Intel Core i5 CPU: 2-core
2 GB RAM
BANK 0/DIMM0
1 GB DDR3 1333 MHz ok
BANK 1/DIMM0
1 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 288 MB
VA2037 SERIES 1600 x 900 @ 60 Hz
System Software: ℹ️
OS X 10.8.5 (12F45) - Time since boot: 3 days 4:25:7
Disk Information: ℹ️
TOSHIBA MK5065GSXF disk0 : (500.11 GB)
disk0s1 (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 499.25 GB (76.72 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
Apple Inc. iPhone
Western Digital My Passport 0748 500.07 GB
disk1s1 (disk1s1) <not mounted> : 210 MB
My Passport (disk1s2) /Volumes/My Passport : 499.73 GB (67.99 GB free)
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Incompatible Software/avast!.app
[not loaded] com.avast.AvastFileShield (1.0.1) [Support]
[not loaded] com.avast.PacketForwarder (1.3) [Support]
/System/Library/Extensions
[not loaded] com.cisco.nke.ipsec (2.0.1) [Support]
Startup Items: ℹ️
HP IO: Path: /Library/StartupItems/HP IO
Startup items are obsolete in OS X Yosemite
Problem System Launch Agents: ℹ️
[failed] com.apple.accountsd.plist [Details]
[failed] com.apple.coreservices.appleid.authentication.plist [Details]
[failed] com.apple.lookupd.plist [Details]
[failed] com.apple.pbs.plist [Details]
[failed] com.apple.tccd.plist [Details]
Problem System Launch Daemons: ℹ️
[failed] com.apple.wdhelper.plist [Details]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
User Launch Agents: ℹ️
[loaded] com.divx.agent.postinstall.plist [Support]
[loaded] com.google.keystone.agent.plist [Support]
[invalid?] uk.co.markallan.clamxav.freshclam.plist [Support]
User Login Items: ℹ️
Microsoft Database Daemon Application (/Applications/Microsoft Office 2008/Office/Microsoft Database Daemon.app)
Dropbox Application (/Applications/Dropbox.app)
Google Drive Application (/Applications/Google Drive.app)
HP Scheduler Application (/Library/Application Support/Hewlett-Packard/Software Update/HP Scheduler.app)
Internet Plug-ins: ℹ️
AmazonMP3DownloaderPlugin1017277: Version: Unknown
OVSHelper: Version: 1.1 [Support]
OfficeLiveBrowserPlugin: Version: 12.3.6 [Support]
Flip4Mac WMV Plugin: Version: 2.3.1.2 [Support]
Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Support]
FlashPlayer-10.6: Version: 16.0.0.287 - SDK 10.6 [Support]
DivXBrowserPlugin: Version: 2.2 [Support]
Flash Player: Version: 16.0.0.287 - SDK 10.6 [Support]
AmazonMP3DownloaderPlugin: Version: Unknown
QuickTime Plugin: Version: 7.7.1
iPhotoPhotocast: Version: 7.0
HypercosmPlugIn: Version: 1.0 [Support]
Scorch: Version: 6.2.0 [Support]
JavaAppletPlugin: Version: 14.3.0 - SDK 10.8 Check version
User internet Plug-ins: ℹ️
Google Earth Web Plug-in: Version: 6.0 [Support]
Picasa: Version: 1.0 - SDK 10.4 [Support]
BrowserPlus_2.7.1: Version: 2.7.1 [Support]
3rd Party Preference Panes: ℹ️
BrowserPlus [Support]
DivX [Support]
Flash Player [Support]
Flip4Mac WMV [Support]
Time Machine: ℹ️
Mobile backups: OFF
Auto backup: YES
Destinations:
My Passport [Local]
Total size: 499.73 GB
Total number of backups: 35
Oldest backup: 2013-11-28 08:26:20 +0000
Last backup: 2015-01-24 16:14:06 +0000
Size of backup disk: Excellent
Backup size 499.73 GB > (Disk size 0 B X 3)
Top Processes by CPU: ℹ️
17% mds
6% iPhoto
3% activitymonitord
2% WindowServer
1% Activity Monitor
Top Processes by Memory: ℹ️
161 MB WebProcess
132 MB iPhoto
86 MB Safari
82 MB App Store
62 MB iTunes
Virtual Memory Information: ℹ️
33 MB Free RAM
674 MB Active RAM
668 MB Inactive RAM
769 MB Wired RAM
12.57 GB Page-ins
12.61 GB Page-outsOnly 2 GB is your man problem. You Mac can accept 16 GB. If tight for money get one 8 GB stick and replace one of yuor 1 GB sticks with the 8 GB stick
http://eshop.macsales.com/shop/memory/Apple_Mac_mini/DDR3_1333
12.57 GB Page-ins
Uninstall your antivirus
[invalid?] uk.co.markallan.clamxav.freshclam.plist [Support]
and this one too. Have two is very bad
/Incompatible Software/avast!.app
[not loaded] com.avast.AvastFileShield (1.0.1) [Support]
[not loaded] com.avast.PacketForwarder (1.3) [Support]
Update this
HP IO: Path: /Library/StartupItems/HP IO
Startup items are obsolete in OS X Yosemite -
Why does my mac mini run great for first half hour then run so slow almost to a stop?
why does my mac mini run fine then after a half hour runs very slow?
EtreCheck version: 2.2 (132)
Report generated 4/30/15, 3:58 PM
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Click the [Click to remove] links for help removing adware.
Hardware Information: ℹ️
Mac mini (Late 2012) (Technical Specifications)
Mac mini - model: Macmini6,1
1 2.5 GHz Intel Core i5 CPU: 2-core
16 GB RAM Upgradeable
BANK 0/DIMM0
8 GB DDR3 1600 MHz ok
BANK 1/DIMM0
8 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 4000
Thunderbolt Display 2560 x 1440
System Software: ℹ️
OS X 10.10.3 (14D136) - Time since boot: 7:15:27
Disk Information: ℹ️
APPLE HDD HTS545050A7E362 disk0 : (500.11 GB)
EFI (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 499.25 GB (475.54 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple, Inc. IR Receiver
Apple Inc. Display Audio
Apple Inc. Apple Thunderbolt Display
Apple Inc. FaceTime HD Camera (Display)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Apple Inc. Thunderbolt Display
Gatekeeper: ℹ️
Mac App Store and identified developers
Startup Items: ℹ️
FanControlDaemon: Path: /Library/StartupItems/FanControlDaemon
Startup items are obsolete in OS X Yosemite
Problem System Launch Daemons: ℹ️
[failed] com.apple.mtrecorder.plist
Launch Agents: ℹ️
[loaded] com.oracle.java.Java-Updater.plist [Click for support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Click for support]
[failed] com.apple.spirecorder.plist
[loaded] com.macpaw.CleanMyMac3.Agent.plist [Click for support]
[loaded] com.oracle.java.Helper-Tool.plist [Click for support]
User Launch Agents: ℹ️
[not loaded] com.jdibackup.JustCloud.autostart.plist [Click for support]
[loaded] com.jdibackup.JustCloud.backupstart.plist [Click for support]
[loaded] com.jdibackup.JustCloud.notify.plist [Click for support]
[loaded] com.macpaw.CleanMyMac3.Scheduler.plist [Click for support]
[running] com.spigot.SearchProtection.plist [Click for support]
User Login Items: ℹ️
iTunesHelper Application Hidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
CleanMyMac 3 Menu Application Hidden (/Applications/CleanMyMac 3.app/Contents/MacOS/CleanMyMac 3 Menu.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 17.0.0.169 - SDK 10.6 [Click for support]
Flash Player: Version: 17.0.0.169 - SDK 10.6 [Click for support]
QuickTime Plugin: Version: 7.7.3
JavaAppletPlugin: Version: Java 8 Update 45 Check version
Default Browser: Version: 600 - SDK 10.10
Safari Extensions: ℹ️
Slick Savings Adware! [Click to remove]
Ebay Shopping Assistant Adware! [Click to remove]
Searchme Adware! [Click to remove]
3rd Party Preference Panes: ℹ️
Fan Control [Click for support]
Flash Player [Click for support]
Java [Click for support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
4% WindowServer
2% fontd
0% taskgated
0% notifyd
0% cloudpaird
Top Processes by Memory: ℹ️
836 MB kernel_task
82 MB WindowServer
66 MB JustCloud
66 MB SubmitDiagInfo
66 MB loginwindow
Virtual Memory Information: ℹ️
12.00 GB Free RAM
4.33 GB Used RAM
0 B Swap Used
Diagnostics Information: ℹ️
Apr 30, 2015, 08:42:48 AM Self test - passed
Apr 29, 2015, 09:04:50 AM /Users/[redacted]/Library/Logs/DiagnosticReports/com.apple.WebKit.WebContent_20 15-04-29-090450_[redacted].crash -
Monitor Issues after upgrading Mac Mini OS to Mavericks
I upgraded my older Mac Mini OS to Mavericks. The monitor always worked fine on Snow Leopard (10.6.8 I think), but now my Hanns G monitor takes fifteen minutes to display anything. Until then it is blank and makes clicking, popping noises every 3-5 seconds. After it comes up, it works fine and all the settings seem to be correct. Any ideas? Many thanks for any help you can provide.
Some more info: the monitor is a Hanns G HC194D and is set for 1280 x 1024 with a NVIDIA GeForce 9400 256 MB graphics. My Mac Mini has a 2.26 GHz Intel Core Duo processor and has 2 GB 1067 Mhz DDR4 memory. The monitor display profile says it was created two weeks ago which strikes me as a bit odd, but I updated the OS well before then and this has been an issue since I updated to OS 10.9.3. I have played around with the cables and the connections are tight, and once the monitor finally displays after 15 minutes or so on start-up or deep sleep, the monitor looks and runs fine.
It seems too coincidental that this problem only surfaced after upgrading the OS for it to be a monitor hardware issue, but I haven't seen any other reports of this type of problem. This is a very frustrating problem, so thanks for reading this far. -
Is it possible to screen share an old iMac running 10.4 with a new Mac Mini running Yosemite
Is it possible to screen share an old iMac running 10.4 with a new Mac Mini running Yosemite. I am trying to bring the old iMac screen up on the Yosemite system
Hello! Not out of the box: OS X Mountain Lion: About screen sharing You'll have to look for third-party options like Teamviewer
Maybe you are looking for
-
HP m7160n front audio jack problem
I am running Vista Home on my m7160n Media Center PC. I used to be able to plug in my headphones to the front audio jack and it would cut out the rear speaker output. Now it doesn't! I have gone into sound properties and is IS set to turn off rear
-
X58 Pro will not install Vista/7
Specs: Mobo: MSI X58 Pro MS-7522 CPU: Core i7 920 RAM: Corsair TR3X3G1333C9 Triple-Channel DDR3 1.5v 9-9-9-24 PSU: Thermaltake PurePower 500W +12V-14A and +12V-15A OS Installed: Vista Ultimate 32-bit Primary HDD: Seagate 750GB 7200 RPM Secondary HDD:
-
Reports 10g dynamic image logo
Hi, I want to insert an employee image which changes in reports and taken from file system.I dont want to take image from database.Is there any solution? Your ideas will be appreciated. Regards,
-
My desktop C drive is full HD of 1 TB, I would like to move the current iTunes master file to an external 4TB drive and then iTunes stick with the external drive Could this be done, if yes how to do it? Thank you for your help Henri
-
Adobe Muse Hide Adobe Muse Does Not Work
I have noticed that choosing Adobe Muse > Hide Adobe Muse does not hide the program. The program remains but goes in the background and another program comes forward.