On-The-Go Playlist: what is it and how to use?

I've read the notice on the iPod when you select the On-the-Go playlist but don't know what it does and how to best use it. I've tried to add a song to it by holding down the center button while the song was playing but don't know how to check to see if it's been added. When I go to the On-the-Go playlist in the menu I only get the text instructions. Can someone describe how to add, and remove, songs from it or tell me if you can and how to use it?
OT

EDIT: BAH! I posted too slow... but there is still some information about saving and clearing in there
Its for making a playlist while your 'on the go'. So you click and hold the middle button the selected song (or album) should flash... Then you go into the playlist menu (music>playlists>on-the-go) and use it like any normal playlist...
When there's songs on the playlist it gives you the option to save or clear at the end of the song list, you select either one and it'll ask for conformation.
It works in both manually sync and auto sync mode. But if you have it on auto sync the play list will be created in iTunes...
So I'm not sure why you don't see songs in it after yo assign them to it, try sending a whole album and then music>playlists>on-the-go the album songs should be listed.
As for reasons to use it well maybe while out and about you realise that you want to hear from two artists at the same time, Radiohead and Bowie, in a shuffle mode. You could make it a on-the-go playlist. Or there's a few podcasts you want to hear in order... so you go down the list and assign them to on-the-go.
Some people use the On the go to note songs that need to be looked at in iTunes later, maybe because its too quiet, badly imported or they don't understand how such a bad song found its way onto the iPod.
Once you save it if you try and put more songs to it, 'on-the-go-1' will be created.
-hope this helps

Similar Messages

  • I tried to import a PDF of a line drawing into Photoshop Elements. The thumbnail looks fine, but when imported the file is empty. This used to work in the past. What is wrong and how do I solve this?

    I tried to import a PDF of a line drawing into Photoshop Elements. The thumbnail looks fine, but when imported the file is empty. This used to work in the past. What is wrong and how do I solve this?

    Hi
    The value of the Channel Strip volume etc is not stored within the C Strip setting, as you have discovered.
    If you really wanted, you could add a Gain plug to the strip, with it set to give the correct output level with the Fader set to 0
    (Or just set the fader manually in MS)
    CCT

  • I want to know what's the conference call in community level and how to use it

    i want to know what's the conference call in community level and how to use it

    Welcome to Apple Support Communities
    Conference calls are got when you reach level 4. Sometimes, ASC hosts may do a conference call about something related to Apple Support Communities. You will be notified through mail or through the "Using Apple Support Communities" forum.
    The last community calls were only for level 6 and higher users, so it's possible that you don't get invited to any until you reach level 6

  • I have an iphone  4 8gig there is 2.4 gig of "other" showing on my usage which is more than all oter data on the phone.  What is it and how do I delete some to clear space?

    I have an iphone 4 8gig there is 2.4 gig of "other" showing on my usage which is more than all other data on the phone.  What is it and how do I delete some to clear space?

    Sorry. We can't help you. It's no longer an iPhone. Apple won't touch it.
    Take it to whoever replaced the screen and see if they can help you.
    iPhones are not user servicable and Apple does not sell iPhone parts at all. I'd be surprised if you were actually able to back it up at this point. It sounds like it's completely borked.

  • Just below toolbar, Firefox is telling me "Downloading the lastest applications" - what is this and how can I stop it. It's been running for 2 hours.

    Just below the toolbar, Firefox is telling me "Downloading the latest applications" - what is this and how can I stop it. It's been running for 2 hours.
    == This happened ==
    Every time Firefox opened
    == I opened the Firefox "Add-ons" window

    Disable or uninstall the MSN/Bing toolbar.
    See [https://support.mozilla.com/tiki-view_forum_thread.php?comments_offset=0&comments_threadId=0&comments_parentId=693619&comments_threshold=0&thread_sort_mode=commentDate_asc&forumId=1&time_control=3600 this thread] and [[Uninstalling add-ons]].

  • I have an apple tv 1st generation, and there is a setting for airtunes. can someone tell me what this is and how to use it?

    I have an apple tv 1st generation, and there is a setting for airtunes. can someone tell me what this is and how to use it?

    I've looked at that, but on my PC, "look for remote speakers connected with airtunes" isn't an option.
    The only options I get are "prevent ipods [etc] from syncing automatically" , "warn me when [X %] of the data on this computer will be changed" and "forget all remotes". Its also got a list of backups I have saved, as well as a button to reset sync history.
    When I am playing a song, the "airplay" button isn't even visible.
    I am sure that the apple tv setting is on as well. Is there anything else you can help me with?

  • How does the URL of DataSocket constitute?And how to use it in LabWindows/CVI ?

    Hi !
    There's a problem puzzled me some days.How does the URL of DataSocket constitute ? And how to use it in LabWindow/CVI ?
    For example.I have downloaded a code in http://zone.ni.com/devzone/cda/epd/p/id/3787.I want to make it work properly.So I configure my DataSocket Server Manger according to the URL of this statement.
    DS_Open ("dstp://weather.natinst.com/weather/current",
    DSConst_ReadAutoUpdate, DSCurrentCallback, NULL,
    &dsCurrentHandle);
     My DateSockket Server Manger is configured as:
    However,it could not work properly when I debug it.
    There's a introduction at the top of the code."You may need to replace the references to weather.natinst.com to 130.164.140.10 if the DNS isn't working properly."So,I modified the statement into
    DS_Open ("dstp://130.164.140.10/weather/current",
    DSConst_ReadAutoUpdate, DSCurrentCallback, NULL,
    &dsCurrentHandle);
    but,it did work properly.
    We want to communicate with other computers via the URL of  DataSocket in LabWindows/CVI.Whereas,how could we make it ia the URL ?
    If anyone could help me solve this problem,I would appreciate it very much !
    Best regards.
                     xiepei
    I wouldn't care success or failure,for I will only struggle ahead as long as I have been destined to the distance.

    Hi !
    Thank you very much for your reply! I will accept your advice.
    Besides,I have another question.If I want to visit other computers or other websites,how does the URL of DataSocket  I constitute ? Does the URL has any relation with the DataSocket Server Manger ?If does,how to configure the DataSocket Server Manager to let them connected.If they have no relation,how to use the DataSocket Server Manger ?
    After all,I want to know how to use it in LabWinows/CVI ?
    Thank you very much !
    Best regards!
    I wouldn't care success or failure,for I will only struggle ahead as long as I have been destined to the distance.

  • HT5487 my ipod touch is stuck with an I tunes logo and a usb chord with an arrow pointing to the logo. What is this and how do I fix it?

    My Ipod is stuck with a picture of a USB chord with an arrow pointing to an itunes logo....what is this and how do I fix it? I did look at the "printers and devices" section on my computer. It shows an un identified "apple" device that is in "recovery mode" but that is. I tried to trouble shoot it there but no help....

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/HT1808

  • Im new to CRM, can any body say about the BPEM. What is it and how work on?

    Hi SAP Gurus,
          Im new CRM, Can any body say me what is BPEM and how can i work on it. Is it present only in ISU ? or can i see it in CRM also?
    Thanks in advance.

    The line in question can be split up into 3 different lines.
    a[n] = next;
    System.out.println(a[n]);
    n++;

  • VPN. What's this and how to use it?

    Hello,
    Recently I started to work from home and not the office. To connect to my work server my company's sysadmin sent me the requisites to connect to VPN (I need to ssh to my work server but it's allowed to the limited set of IPs). But I have no idea what to do next. How to set up the connection and how to use it?
    Thanks

    Thanks! I've tried to follow the steps described in the wiki article but unfortunately stucked on 'Making Your Connection' section:
    # pon tunnel debug dump logfd 2 nodetach
    pppd options in effect:
    debug # (from command line)
    nodetach # (from command line)
    logfd 2 # (from command line)
    dump # (from command line)
    noauth # (from /etc/ppp/options.pptp)
    refuse-pap # (from /etc/ppp/options.pptp)
    refuse-chap # (from /etc/ppp/options.pptp)
    refuse-mschap # (from /etc/ppp/options.pptp)
    refuse-eap # (from /etc/ppp/options.pptp)
    name pshevtsov # (from /etc/ppp/peers/tunnel)
    remotename PPTP # (from /etc/ppp/peers/tunnel)
    # (from /etc/ppp/options.pptp)
    pty pptp xx.xx.xx.xx --nolaunchpppd # (from /etc/ppp/peers/tunnel)
    crtscts # (from /etc/ppp/options)
    # (from /etc/ppp/options)
    asyncmap 0 # (from /etc/ppp/options)
    lcp-echo-failure 4 # (from /etc/ppp/options)
    lcp-echo-interval 30 # (from /etc/ppp/options)
    hide-password # (from /etc/ppp/options)
    ipparam tunnel # (from /etc/ppp/peers/tunnel)
    proxyarp # (from /etc/ppp/options)
    nobsdcomp # (from /etc/ppp/options.pptp)
    nodeflate # (from /etc/ppp/options.pptp)
    require-mppe-128 # (from /etc/ppp/peers/tunnel)
    noipx # (from /etc/ppp/options)
    using channel 28
    Using interface ppp0
    Connect: ppp0 <--> /dev/pts/3
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3541a215> <pcomp> <accomp>]
    Script pptp xx.xx.xx.xx --nolaunchpppd finished (pid 26089), status = 0x0
    Modem hangup
    Connection terminated.
    I don't know what to do

  • What is PKCS7 and how to use it?

    Hi! I'm in a project in which I must send a file encrypted with a key that is also encrypted with a public key, the receiver must decrypt the key using his(her) private key, and then, using that decrypted key to in turn decrypt the file.
    I've been told to use PKCS7 standard, but is not clear for me how it works, and how to use it. I use bouncycastle, and know that it has APIs to do something like this.
    Any light will be greatly appreciated!

    Look at the CMS functionality in the bouncycastle provider, in the bcmail distro. You can find some examples in the bcmail distro also. Maybe I'll post an example later.

  • No matter what website I am on all of a sudden the page will be covered in black and white lines and I can't see any of the page. What is happening and how do I fix it? It has only started since I loaded Firefox 4 this week.

    I am very frustrated because I keep having my pages become covered completely in black and white lines. It has even happened on this page when I tried to use the drop down arrow by 'this happened'. I can sometimes read the page if I click over the area I want to read but this is not common. This has only been happening since I downloaded Firefox 4. I thought this would be a better version but now I am not so sure.

    I do not want to download another virus program.. I do not believe it is a virus. I am running the full version of Norton 360 and it is doing a daily scan. I have Windows 7, 64 bit OS.
    This is very irritating !! If I wanted Yahoo I would ask for it !

  • Can someone explain the OCI cocncept to me, what it does and how to use it?

    Bit a newbie question, but whta does the OCI do, and how does it work.Start from the base.
    Peter

    http://www.orafaq.com/faqoci.htm
    "The Oracle Call Interface (OCI) is a set of low-level APIs (Application Programming Interface Calls) used to interact with Oracle databases. It allows one to use operations like logon, execute, parse, fetch, etc. OCI programs are normally written in C or C++, although they can be written in almost any programing language."

  • The change flag in partner profiles and how its used?

    Hi,
    can any one succinctly explain the use and purpose of the change flag in the message control part of the partner profile configuration?

    Hello,
    The value of this field is use internally in FM attached to the process code  for Creation/Change and in case of change, only the relevent changed data is sent ( taken care by attched FM).
    Thanks & Regards,
    Pieter

  • I have just updated my Ipod to version 6 but my ipod now states ios6 on the front of it and has all different languages on the slide button. what has happened and how do i put it right?

    I have just updated ny ipod tough to version 6 and now it states ios6 on the front screen and where it says slide to input security no it is in all different languages.  What do i need to do to sort?

    Fire97 is corret. It appear that you have to resetup/activate the iPod. Just slide to unlock and following the on-screen prompts.

Maybe you are looking for

  • When I move across my tabs and touch one to change focus to it, it opens in a new window. The tab goes from my list of tabs and is there as an opened womdow

    by touching a tab with the mouse pointer it moved from the tab into a new firefox window.The existing tab has gone.So I need to reload it in the original firefox alongside my other tabs. To the best of my knowledge I have not downloaded any new addon

  • New Azure Database does not have a manage button

    I just created new azure databases on a new Azure subscription. Everything appears to be in place except the Manage button is missing in the portal (both the old one and the new one). The manage button is displayed on the old subscription. I made sur

  • BUS2081.PreliminaryPost in error

    Hi experts, maybe someone of you has met this problem (rel. 4.7). In a custom WF with BO BUS2081 (Incoming Invoice) I use the background task TS20000883 (PreliminaryPost). In a particular case it goes in error because of wrong allowed posting periods

  • Insert 100% width flash banner in HTML

    Hi all, i am trying to insert a 100% width flash banner in an html page. The problem i am facing is that i am inserting the banner inside a div which has some margin in it. This is effecting the percentage size of the flash banner. How can i display

  • Firefox Button in XP

    Running XP if the menu toolbar is not clicked in view, the "Firefox Button" appears but does not have all of the options available from the menu toolbar. Specifically, tools, which I use frequently. If the Firefox Button is supposed to replace the me