Onboard sound and video IRQ prob

Well I have norrowed down a prob I believe is with the sound and Video using the same IRQ.
Both are using irq 16...
Why windows would put them on the same irq is beyond me.
Is their a way to change this?
Mobo is KT4 ultra with c-media sound
video is geforce4 ti 4200
System keeps rebooting when in games.
I just did a fresh install and installed drivers and bleh same thing.
I also turned off plug and play in bios. which microsoft recommends.
Any help would be great
r00t 3:16

Well considering their is a alot of IRQ's and half of them aren't in use you would think ms would not assign a video and sound to the same irq.....
At any rate. Im not sure what games you play but most games check to see if your sound card is working before it loads.
So that won't work.
I didn't have any problem with this system until I formated and redid everything I should of just stayed with it as it was.
Then the sound was on irq 16 and the video went to irq 128?
Thats right 128....
I didn't have to disable APIC either.
Although I did however have plug n play support disabled in the bios.
I also installed all drivers and devices before I added the service pack.
Maybe ill just get a different sound card.
Who knows.
But at any rate IRQ 5 is reserved for sound cards from what I read online. Unless you have a SB series they like irq's 7 or 9....
Anyways ill let everyone know what I did then.
r00t 3:16

Similar Messages

  • Can a MacBook (Early 2008) Support both sound and video to 1080p HDTV by Mini-DVI to HDMI cable?

    Can a MacBook (Early 2008) Support both sound and video to 1080p HDTV by Mini-DVI to HDMI cable?

    The mini dvi on the MacBook will only support video, in order to get audio you'll need to a cable from the sound out port to the sound in port on the TV.

  • How do you get sound and video from a macbook pro (before 2010) onto a 2010 toshiba 40" tv?

    Any help on connecting a macbook pro (late 2009) to a 2010 toshiba 40" for both sound and video?  I have the mini-hdmi cable, but have no idea about running sound through the tv.  I can use the headphone jack, but don't know where to connect it to on the back of the tv.  Am I supposed to change any settings on the tv or computer to allow the sound to go through the tv?  thanks for any help.

    You need a stereo mini to RCA break out cable.
    https://discussions.apple.com/message/16276201#16276201

  • Loss of sound and video playback on ENVY X2

    Every so often, more often than I would like, my HP Envy X2 loses sound and video playback capabilities; any ideas anybody? The concept of this machine is great and have had it for the past 9 months but this loss of sound and vision is so unpredictable and frustating...  

    Hi Brumage,
    I saw your post regarding the sound and video issues and I will be happy to help. Do you get any error messages when this happens? Have noticed if it is a particular site like YouTube or program that you are using when the issue occurs or does it occur on all programs? When you restarted the Envy X2 does the issue go away?
    I would start by suggesting that you make sure all updates have been installed through HP Support Assistant and Windows Update.
    What operating system are you running? What is your product number?
    Find your product number on a notebook:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c00033108
    Finding your OS:
    http://windows.microsoft.com/en-CA/windows/which-operating-system
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • How to enter bios, disable onboard sound, and install a sound card

    How do I enter bios, disable onboard sound, and install a sound card?

    Hi,
    You may also have to disable, security for the PCIE x1 slot.
    Windows 8.1 - Accessing the UEFI (BIOS) Setup
    Regrads

  • Mismatch between sound and video

    When I watch a movie in iTunes of Apple TV (2gen) and I want to move it few seconds/ minutes and more backwards then it like "losing its mind",
    the video jumps forward (a lot forward) and the sound stays the same, so ther is mismatchment between sound and video.
    What can i do to solve this problem?
    Thank you!

    Am I the only one suffering this issue with the video transcoding?

  • [Python pygame] Graphic equalizer - keeping sound and video in sync

    Hi!
    I'm writing a graphic equalizer in python and I want to use pygame for the video and audio output.
    The video display of the moving bars works great, now that I have a correct way to read samples and decode them.
    The problem now is: they're way out of sync with the audio playing in the background!
    At the moment my code, that draws the bars basically looks like this:
    # loop as long as we can get slice of the audio file for the fft
    for n_frame in range(0, len(framebuffer), fftframesz):
    clock.tick_busy_loop(t_loop)
    # t_loop was defined as fftframesz over total_frame_count
    # which means in words: t_loop is the amount of FFTs per second - or the cycles of THIS loop
    # grab the frames and perform the fft here
    ...numpy.fft.fft...
    # set the new bar heights and draw them
    for bar in bars:
    bar.update()
    # if playback has not started yet, make it so
    if not pygame.mixer.get_busy():
    musicfile.play()
    The way I'm thinking, this should be enough to keep sound and video in sync. Because we know the time that one cycle should take at most,
    we can set the clock to tick_busy_loop this time. This way we make sure that the video is not faster than the sound.
    But to me it seems that is is the other way round, i.e. that the video is slower than the sound. I already did some timing, but to no avail.
    Is there perhaps a more easy, more elegant way to make sure that image and audio are in sync?
    Any help is greatly appreciated!
    Last edited by n0stradamus (2012-10-01 18:36:53)

    Thanks for your ideas. I assume you mean I should go with a $1200.00 final cut pro software. NOT.
    Sure the video will be on myspace and youtube but wether they are noticed or not is not as important as self satisfaction. I can easily split scenes into equal time zones as I said. Then drag them into clips and back all using the same camcorder. Multiple cameras and angles would be nice but this can be done on a low budget and still look good. I guess my original questions were not answered. Is there a way to determine the length of a transition and shorten the clip by that amount. Or the length of a still shot and do the same. Or perhaps they have been answered and the answer is NO WAY, and I am just not hearing it.
    I suppose reimporting a video would be great if I could use two timelines like in audio and then blank out what I don't want in the first. But I just don't think this is possible, or is it. I've been reading iMovie HD6 The Manual that should have been in the box. It's a help but doesn't take you from the beginning of a project to the final project. Exporting to imovie or idvd is not an issue. BTW I got the clips in sync as I said by leaving blank spots and placing effects over them. I could insert the proper length video in those spots but that can look silly without transitions. But then again so can transitions. This stuff is very fun and interesting and a great learning experience. If I stop now as you suggest then I am not pushing myself to the limit. But thanks for your reply.

  • Sound and video are choppy since installing Flash Player 11.3

    I'm having a problem here!  Since I updated Adobe Flash Player 11.3, the audio and video are all choppy when I play Adobe Flash game apps in Facebook!  Even when I disabled hardware acceleration, the sound and video are STILL choppy!  Even I watch a YouTube video and the sound and video are a bit choppy!  There's DEFINITELY some sound issues in Flash Player 11.3!  I'm using Firefox 13 in Windows XP SP3.  I'm wondering if you have any answers for the sound issues in FP 11.3. 

    I went through an annoying password reset process to post on here, haha, I was experiencing this issue and managed to resolve it for a flash animation I was making that was going to be sent out; thus fixing it for myself wouldn't change things for others. I know this is old, but if anyone is in this position, I hope it helps.
    I was using Swish Max for my scenario.
    Under the Export Settings, I found that by default it was using SWF Version: SWF8 - when it had the option to go up to SWF10. I changed it to 10, and set the hardware acceleration to Level 1 - Direct.
    I exported, and it still didn't work. The music was choppy as heck and terribly inconsistent with speed. I even created a preloader, which appeared to work but didn't resolve my issue.
    FINALLY, I kept it at version 10, and found that it had an option that said "Preload Content: Disabled." I set that to "At Preload Frame" and though I had a loading animation setup to do the preloading, I still placed a preloadcontent keyframe at frame 1. Then I set Hardware acceleration to Level 2-GPU and exported.
    IT WORKED. The terrible, seemingly non-fixable audio cracking lag was gone and it worked flawlessly.
    Hope this helps someone, I originally found this when I was trying to find a fix for the issue.

  • Equium-A100-147 - broken sound and video

    Hi everyone,
    I have the Equium A100-147, Its been working fine for last couple of year.
    But in the last few weeks has get problem in sound and video (broken sound and video).
    The sound is breaking and sometimes uable to listen + video breaking and so much delay due to its get so slow with so much sound distorsion etc..
    This remains after new installation (format HDD) of Wind XP unable to fix even installed new drivers.
    The Device Manager shows all drivers including audio and video working ok, d'nt know what's problem please help me.
    Thanks.

    Hi
    Something like that can happen during high HDD activity this means that the reading/writing process could affect the sound/video playback
    But usually this should not take long time
    At the other hand this can happen because of higher temperature
    High temperature can affect the CPU and GPU performance
    I think you have used this notebook for couple of month without any troubles in my opinion you should check if cooling modules and fans are clogged and could remove the dust and debris from cooling modules use compressed air spray this helps p get rid of dust
    Maybe then the notebook will run much better

  • URGENT- DOING MEMORIAL VIDEO sound and video are off when sent to iDVD

    I watch the video in iMovie and the sound and video are in sync. When I send to iDVD, the two are no longer in sync. I have made changes to the iMovie project since my last DVD burn. With the initial burn, there were no sound issues.
    I've tried all of the following:
    1. closing and reopening iMovie and iDVD
    2. resending from iMovie to iDVD
    3. readding the clip and removing the original clip from the iMovie project
    4. restarting my computer
    The only things I have not done are the following:
    1. redownloading the original video clip from my camcorder
    2. recreating the project
    3. trying a different project to see if that one has the same audio/video issue (this will be my next step)
    #2 above is literally so intense as I have a lot of editing on this. To make it clear to you, I have video footage of a memorial.... and after the memorial I chose little 20-30 second clips here and there. I don't have audio with those clips -- just iTunes music overlay.... so, those I don't need to worry about sound coinciding.... just the 30 minute clip that is the actual memorial service.
    This is time sensitive.... it is a memorial video and I don't have time to redo the thing from the beginning, especially considering how long it took me to find those 20-30 second clips of the post-memorial.
    Please help!

    Yes... I had seen that.... and, yep, have the latest software.... and even rebooted my machine thinking that maybe it hadn't been restarted since the update (can't remember how long ago the update was).
    I did a test run with a mobile size (it takes over an hour when I share with iDVD, which has been annoying with all my attempts to "fixing") file sharing with media browser and still the sound was not matched.
    I started another project alltogether in iMovie and it does not have the sound issue when sent to iDVD....
    I can copy and paste the more difficult editing I did between the "bad original copy" and my "do-over"... but, it seems to not copy exact length of each clip (it decreased it by a second each clip on the ones I copied over but that is weird since it did copy over the slowed % I had on the original) ..... see the more complex editing I have has the sound silenced and I have music overlay on that....
    I have many more to go... and can't copy text directly from one project to another... in fact, there is a lot you can't just copy over.... I have to redo the music, special effects etc. This is not going to be a walk in the park if I can't find a way to make my "bad original copy" work.
    Still looking for more suggestions (than to start all over), but will have to start over if I spend too much time making the one I have work.... then it becomes more sensical to just start over. I have quite a bit of time in the original, but if I can copy and paste the clips, that takes a majority of the work out.... but, if any of my copy and pastes somehow "corrupt" the sound sync on the portion that isn't silenced and music overlaid, then, there is a lot of work having to recreate all my edits from scratch.

  • G5 powerBook; intel cpu; recently upgraded 10.3.9 to 10.5.8 along with iLife6. After several upgrades from Apple, iMovieHD is a mess. Clip indicator runs 3 clips ahead of the sound and video. Jerky. Unusable.

    G5 PowerBook; Intel cpu; recently upgraded 10.3.9 to 10.5.8 also upgraded to iLife6. After several downloads suggested from Apple, iMovie6 is a mess. Clip indicator runs 3 clips ahead of the sound and video. Jerky. Unusable. All the movies were created with iMovie 4 and loaded all into this version and saved all in this version.
    Video card is GeForce FX 5200; Quartz Extreme: Supported: Core Image: Hardware Excelerated.
    Perhaps in the multiple downloads, Apple sent me a version that outruns my aged video card?
    Help is most appreciated

    The uptime of your Mac is more than 10 days. How about a simple reboot?

  • HT1926 Quicktime stuttering, MOV file plays fine on my iphone but play it in my PC the sound and video stutters. happened only after the last update. how to fix

    Quicktime stuttering, MOV file plays fine on my iphone but play it in my PC the sound and video stutters. happened only after the last update. how to fix?

    Hi Richmoller51,
    Welcome to Apple Support Communities.
    See this article for some troubleshooting steps that can help with video playback in iTunes or Quicktime:
    Troubleshooting iTunes for Windows Vista or Windows 7 video playback performance issues
    http://support.apple.com/kb/ts1718
    Best,
    Jeremy

  • The sound and video become unsynchronized when the off-line recording was created.

    Hello,
    I recorded a 1.30 hour meeting by using Adobe Connect. I want to edit the file and split in small time. So I save the recording in local by clicking "Make Offline". When I play back the file from local, the sound and video become unsynchronized.
    Any idea and how to sort it out.
    Thanks in advance,
    Nicho

    As I recall, there is an issue with Windows 8 and the offline recording function. Not sure if you are using Windows 8, but it may be worth trying to do it on another computer.
    However, before you go down that road, know that the FLV versions of the meeting recordings are notoriously difficult to edit. If you don't need to have the recordings in a different format, I would recommend that you do the following instead (will be much faster overall).
    Take the URL for your meeting recording and add /output/YourNameHere.zip?download=zip. You can name the zip file whatever you want. This will pull the recording source files down to your local computer. Next, browse to a desired location in your Content library in Connect and re-upload that zip file. You can name it whatever you want, and even create a custom URL for it. Once it is uploaded you will have a second version of the same recording on your server. Just re-upload that zip file as many times as needed. You can then edit each version of the recording separately, allowing you to create as many versions of the recording as needed.

  • Does iMovie have Sound and Video Effects?

    Before i begin filming my college film i wanted to ask and see if imovie has sound and video effects. what i mean is like, say in the film a gun is shot, well does imovie have a shot going off sound? are there sound effects? or am i asking in the wrong place and see if garageband has these?
    also, video effects? i know imovie has like sepia and black and white tones among others but can i add other types of effects? if so, what kinds?
    thanks!

    you're looking for specific effects for your specific needs.. why not launching iM on your MacBook.. and look for your own..???
    BEFORE doing a "serious" project, I would allway do some test/dummy projects, just to get comfortable with some software ...
    plus:
    the two additional audio tracks allow easiely to place small audio snippets, downloaded from anywhere in the web to your movie.. if you need explosions, gunshots, lightsabres, whatever, the iNet is full of sources...
    plus:
    you can teach iM lots of new tricks by installing/purchasing 3rd party plug-ins, if you need very special effects , iM does not support out-of-the-box.
    plus:
    http://www.apple.com/ilife/tutorials/imovie/index.html

  • Interactive PDFs now include sound and video

    Hi Romans,
    We've noticed a few of you have been interested in including sound and video within interactive PDFs. I'm happy to say that the development team has heard your concerns and this has been added to the most recent update.
    So, after updating the application, try this feature out and tell us what you think! Any issues or thoughts to share while using this feature?
    Thanks for the continued feedback,
    Sarah
    Sarah
    Forum Moderator

    Hi,
    This question doesn´t have anythin in common with PDF, but it´s driving me crazy.
    Is about event/ go to url in a action button. If I press the button it doesn´t go the web
    I live you a video to see if you can help me http://bit.ly/hcBq4a
    P.S.: I didn´t know to do a website and I decide to learn with ROME, it was quite easy, until I learn with Dreamweaver, I´d like to solve my problem

Maybe you are looking for