Only 3 rings before voicemail.

How do I extend the number of rings before voicemail kicks in - my 8520 only rings 3 times - not enough to find it and answer it.  Missing loads of potentially important calls.

As a norm, most all carriers have a default 15 seconds of ringtime until the voicemail picks up.
If you do need additional ring time before voicemail: 
The simplest method is to call your carrier and request a longer ring time, up to 30 seconds.
If you have a GSM based phone, some have had success by dialing this number from your phone: **61*XXXXXXXXXXX**30#
Replace XXXXXXXXXXX with the number of your carrier voicemail center (find it by looking at your Phone Dialer > Options > VoiceMail > Access Number. Put your access number in place of the Xs above.
For example, the T-Mobile voice mail access number is 18056377243, and thus the string to dial would be **61*18056377243**30#
Replace the 30 at the end of the string with your desired seconds. For most carriers, 30 seconds is the longest allowed
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Similar Messages

  • Reduce number of rings before Voicemail

    I would like to reduce the number of rings before my voicemail comes on on my Blackberry Z10. It is forwarded from my desk phone and that means that customers are waiting an excessive amount of time before my voicemail kicks in on my BB. I called my carrier (Rogers) and they said they were unable to do this. I'm not sure if their tech support was correct in this, as I've seen on other forums that this is the process by which you change the length of the ring tones.
    Is there a way to reduce the number of rings before voicemail on my Blackberry Z10 in my settings?
    Thanks

    *61 *NNN NNN NNNN *11 *X#
    Where X is ranges from 5 to 30 seconds before a call get forwarded to the voice mailbox
    And NNN NNN NNNN is the VoiceMail number provided by the Carrier
    You can locate the Carrier Voicemail Number in 
    Phone Settings/Call Forwarding/Forward If Buzy

  • Setting tone rings before voicemail starts

    How do you set a certain number of phone call rings before voicemail is activated.

    I checked the iPhone User Guide and can't find away to change the amount of rings before going to Voicemail. Somehow your question ended up in the iPad Forum, I'll ask the host to relocate your question to the iPhone Forum and hopefully someone will know for sure.

  • Amount of rings before voicemail

    Is there a way to adjust the amount of rings before it cuts to voicemail?

    Can only be done by your carrier, so contact them.

  • Number of rings before voicemail

    My phone only rings four times before voicemail kicks in. How do I change this to give me more te to answer?

    This is a setting on the carrier end, not the phone. The easiest way is to call your carrier and ask them to make the change. There are codes you can dial on your phone to change the setting yourself, but they differ by carrier and with no location in your profile, we don't know which carrier you have. But call them. It's not a number of rings, actually, but a time - the max is usually 30-40 seconds.

  • How to increase # of rings before voicemail answers?

    My phone rings 2 times before voicemail answers, need to increase to at least 5 rings. Tried everything, user guide etc. Any ideas?

    Here is the code that I used from my Treo days. Tried it on my iPhone and it worked.
    1. To get the current call forwarding status, enter *#61#[SEND] into your phone.
    2. Write down the 10-digit number(ignore the +1), this is the phone number that your calls are currently being diverted to.
    3. Enter *61*[number]*11[delay]#[SEND] into your phone using the phone number (numbers only) as reported by the status & the delay can be set to (5, 10, 15, 20, 25, or 30) seconds.
    4. To verify that the settings are correct, enter *#61#[SEND] into your phone.

  • Chaning number of rings before voicemail kicks in

    I need more time to get to my phone. The number of rings should be user settable.

    It is. You're not actually setting the number of rings, but the length of time before voicemail picks up. You can do this in one of two ways:
    1. Call AT&T and ask them to increase it.
    or
    2. Follow the instructions in the following post:
    http://forums.cingular.com/cng/board/message?board.id=palm&message.id=4087
    (I realize this is from the Cingular Palm support forum, but it doesn't matter. The process is the same for any GSM phone.)

  • Rings before voicemail

    How can I increase the number of times the iPhone 5 rings before it goes to Voicemail? I can barely get to the phone in time unless it's right in my hand.

    No, you can't increase the number of rings before going to voicemail.

  • Numer of rings before voicemail..?

    is there a way to change the number of rings that will happen before voicemail kicks in?.

    I found this very direct solution on the AT&T Wireless discussion boards. I just did it and it worked on my iPhone 3G:
    1. On your phone, dial *#61# and click Send.
    2. Some information should be displayed: number that the calls are being forwarded to and the delay before the forwarding engages.
    3. Write down the number (including 1)
    4. Dial *61*1xxxyyyzzzz*1130# and hit Send. 1xxxyyyzzzz is the number you wrote down previously, 30 is the delay in seconds. The delay can be set in 5 second increments, 30 is maximum.
    5. Dial *#61# to verify that the new settings are active.
    The original post was here:
    http://forums.wireless.att.com/cng/board/message?board.id=voicemail&thread.id=83 66

  • Setting time (number of rings)  before voicemail picks up.

    Voice mail is intercepting calls sometimes after only three rings.  I want to set to 30 seconds.  How do I do that?

    It is already set by the system at 30 seconds and unless something has changed recently, it can't be changed.  Using a different ringtone sometimes helps.

  • Only 2 rings before going to voicemail!

    Hi, my lumia 820 only rings twice before it goes to voicemail. This often isn't long enough to get across the room! How do I get it to ring more than that? I can't find out anywhere
    Thanks!

    Call divert is a network function. While it is possible to change some settings by sending shortcodes to the network from the phone, not all networks use the same codes or offer the same settings. The simplest way to deal with this is to contact your network support and request they change the settings for you as required.

  • An extra charge for changing the number of rings before voicemail picks up??

    After trying all the tips I could find about changing the number of rings it takes before the voice mail picks up (the 58#, trying access setup on the vm, changing it online, etc…), I finally called the customer support line.  I was put on hold for a few minutes (not a problem) only to have the customer service person return to say that he cannot change it because I would have to pay for the "upgraded" voice mail that is not included in my plan (the plan I just signed up for last month). I find it absolutely absurd that moving the number of rings for vm from 4 to 6 justifies an added cost.   If anyone knows the magic on how to do this for a line that is in the Dallas Ft Worth area, I would be very appreciative.  As for the extra charge to adjust your own voice mail, you can draw your own conclusion on how fair that is...
    And I don't buy that it is not as simple as it appears... if you can program the thing to pickup on three rings then you should be able to adjust the forwarding  and vm to pick up on 6.  i have never had this problem with any other carrier.

    I called tech support, not customer service, and had my rings moved back a few so my answering machine would pick up first.  Voicemail is for back up in case I don't answer call waiting.
    It was free.

  • Increasing Number of Rings Before Voicemail Pickup

    I can't figure out how to let it ring longer before going to voicemail on my 3G iPhone. Any thoughts? Thanks.

    You would need to call ATT and request that they adjust the number of rings.

  • How do I extend the length of time my iphone rings before voicemail cuts in? If I need to use a password, how do I access that on my iphone? I'm a new user.

    HELP!! My voicemail cuts in after just 15 seconds of ringing, which is rarely long enough for me to answer it. How do I increase the length of time it rings? Can I choose not to have voicemail at all, so my phone can just continue ringing until I answer?
    If I need to enter a voicemail password or key, can you tell me step by step because I can't see how to do anything except retrieve and delete voicemail msgs. I'm on O2-UK, if that makes any difference at all. Thank you

    If my response has been either helpful or correct, could you indicate that marking which it is in order that others searching for a similar solution can find find this easily.
    FYI, it's considered bad forum etiquette to ask for points.

  • How do you change the number of rings before voicemail is activated on an iPhone 5?

    Thank You

    I don't believe it is possible to change the time between dialing and when it switches to voicemail.

Maybe you are looking for

  • Correct Install of software on new Hard Drive?

    Hello. The hard drive crashed in my powerbook G4. First time ever. I have several disks to reinstall and get the g4 running again, but not sure which disks I should use and in what order. I have: Mac OSX disk Powerbook G4 Software restore 1 of 3 2 of

  • Using of Oracle Text functions not working in JDev

    Hi, I'm confused about using Oracle Text functions in JDeveloper. It's not possible for me to pass the sql syntax test while creating a view object with a custom query: SELECT score (1) myScore, dokumente.titel, ctx_doc.snippet ('idx_dokumente_titel'

  • Idoc segments

    hi experts,                can anyone tell me how do we create data elements which we use in segment creation WE31 (t-code) thanks in advance

  • Sticky notes - defining color

    i would like the option of not only choosing, but defining several custom colors for the sticky notes app. also i'd like to make them not only semi-, but all transparent.(not the text, but the backgrond color). is there a method to achieve this? thro

  • Terabyte Plus Libraries - What is the Best Practice?

    In my current Aperture library I have 150 gigs and I have only been using it for about a year. Previous to that I used iPhoto for a short time which still has a 60 gig library and previous to that I stored my images in file folders on a windows serve