Only 52 cycles and battery health dipping to 73% at times?

My macbook pro is less then a year old and I lately have been having strange battery health readings. The battery usually lasts a few hours depending on what I am doing with it unplugged. However the health twice now has dipped to 73% and then jumped back up to 89% or 91% and stayed there. Today I checked my battery condition and it said "check battery" but then went back to "good" later that day. I condition the battery regularly.
Here are my specs:
Battery Information:
Model Information:
Serial Number: Sony-ASMB012-376c-2895
Manufacturer: Sony
Device name: ASMB012
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0110
Hardware Revision: 0500
Cell Revision: 0303
Charge Information:
Charge remaining (mAh): 4796
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 4986
Health Information:
Cycle count: 57
Condition: Good
Battery Installed: Yes
Amperage (mA): -1817
Voltage (mV): 12027
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 30
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Display Sleep Uses Dim: No
Battery Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 15
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: No
Charging: No
Message was edited by: cooleymtnbiker1

It's normal for health to fluctuate a bit (mine ranges from 86-96%, and has done that for the past 100 cycles or so). But, your fluctuations are a bit wider than I'd consider normal. Keep an eye on it, and if it dips and stays below 80%, contact Apple before your 1 year warranty expires.
When was the last time you calibrated your battery? That should be done every 2 months or so.
http://support.apple.com/kb/HT1490

Similar Messages

  • After updating to ios 8.0.2 .when i'm unlocking the mobile wallpaper dont display . its shows only network and battery status .

    after updating to ios 8.0.2 .when i'm unlocking the mobile wallpaper dont display . its shows only network and battery status .
    then i need to switch off and switch the iphone. per day i'm doing this for 3 times.
    mean while if some one calls ,its not displaying who is calling.
    need to rectify this ASP

    Hi Tarun 49,
    If you are having issues with your iPhone such as you describe, you may want to try some things to troubleshoot.
    First, quit all running applications and test again -
    iOS: Force an app to close
    Next, I would try restarting the iPhone -
    Turn your iOS device off and on (restart) and reset
    If the issue is still present, you may want to restore the iPhone as a new device -
    iOS: How to back up your data and set up your device as a new device
    Thanks for using Apple Support Communities.
    Best,
    Brett L  

  • New Macbook Pro Retina 15inch is showing up as 1.9months old with 2 cycles on 'Battery Health'!?

    Hi,
    I've just recieved my New Macbook Pro Retina 15inch and installed 'Battery Health', but for some reason it is is showing my Macbook as 1.9months old with 2 cycles!? This Macbook isn't even a day old.. Is this normal!?
    Please advise..
    Thanks,
    P

    That is not unusual.  Note that the actual maximum charge is well above the designed level which is the most important criteria.
    Ciao.

  • 85 cycles and battery dies after 1 minute

    Granted, my macbook is older but she only has 85 cycles.  Any reason why my computer would die in a minute after being unplugged?
    System Profile info:
    Battery Information:
      Model Information:
      Manufacturer:          DP
      Device name:          ASMB013
      Pack Lot Code:          0001
      PCB Lot Code:          0000
      Firmware Version:          0102
      Hardware Revision:          0300
      Cell Revision:          0100
      Charge Information:
      Charge remaining (mAh):          4005
      Fully charged:          Yes
      Charging:          No
      Full charge capacity (mAh):          4005
      Health Information:
      Cycle count:          85
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          130
      Voltage (mV):          12522

    Hi!
    Check that all enviroment variables are complete and still in place?
    JAVA_HOME and DBMS_TYPE and so on
    Also check that all exe files are of the same version, if not, make sure they are.
    You could also try to update disp+work
    rollo

  • Wi-fi failure and battery problems started at the same time

    I can't get the wi-fi to connect to any network. It stopped working a couple of days ago. I have tried with my own wireless network at home and several other networks as well.
    I have tried the following:
    *Settings->General->Reset->Reset Network Settings
    *Restore to Factory Settings
    *Tried my network without security and with WPA (and yes I know the password)
    *With and without MAC-address filter in Router, added the iPods MAC-address (called Wi-Fi Address in the iPod)
    *Changed channel for my Wi-fi network
    *Tried with and without my wi-fi repeater
    *My router is broadcasting the SSID
    *Tried to join the network when it is found by the iPod, with 1 as strenght but then I get "Could not join the network"
    *Tried to add the network as other network, typing in the SSID the it says that it can't find the network.
    I have tried a mix of the above and as I stated above I have also tried other networks that it has been able to join without problems before.
    Some info:
    iPod Touch 16 GB Model MA627ZG
    Version 2.2.1 (5H11)
    Purchased in December 2007.
    Router: Netgear DG834GT
    Firmware: V1.02.04
    Wireless Repeater D-link DWL-G710
    At the same time as this started my battery started to get drained very quickly. 2 hours of listening to an audio book and the battery is empty again.
    I have wi-fi off
    Auto brightness off
    Fetch new data off
    EQ off
    The iPod gets very hot when attached to my computer via USB to get battery charged and I don't have it in a case.

    I am having excatly same problem. It started about two days ago, but I did not update or installed anything just before this issue came up. It looks like it came from nowhere.
    It feels like the touch is constantly trying to connect to wifi, even if it is sleeping and even if the wifi is off! That would explain the very short battery life.
    I have tried to update to 2.2.1. It did not help. I have tried to restore both to 2.2 (which was on when this issue came up) and both to 2.2.1.
    I tried to revert to older firmware 7.3.2 on my airport express. But it it did not seem to make any difference. My macbook is still seeing the wifi as well as before, so it should not be a router problem.
    as well, to comment on ipod being connected to turned off/hibernated computer. it does not make any difference whether it is connected to it or not. Computer does not suck the energy from the ipod. It can only charge it. So whether it is connected or not, the ipod should discharge slowly, which it does not in our case.

  • Battery health 96% with only 18 cycles

    A month ago I bought a brand new unit of the last version of the old 17" model. iStat Pro recognized the battery as new with 100% health. 30 days later it shows 18 cycles and 96% health. To what extent this information is trustworthy? Can I ask for a replacement if that fast aging process continues?

    Don't worry about it too much. My battery's capacity level swings several percentage points even if I check it at different times during the same day. You will probably find that the deterioration rate will not continue linearly, but will stop and even reverse at times.
    Battery readings fluctuate normally because a battery is made up of many cells that all behave slightly differently and deteriorate at different rates. It's hard to accurately track/predict the performance of all of the cells as a group; the number is always more like an estimate.
    Apple has a standard that its batteries should retain 80% capacity after 300 cycles. Apple might not replace the battery until you can show that the battery is going to fall short of it at that time, and it takes about a year to get to 300 cycles.

  • I just bought a new macbook pro 13-inch. I ran coconut battery test and it says age of the macbook is 22 weeks. And the battery load cycles shows 4 and battery capacity is 96%. Is this all normal? Does anyone have same issues?

    I just bought a new macbook pro 13-inch 6 days ago. I ran coconut battery test and it says age of the macbook is 22 weeks. It shows 4 battery load cycles and battery capacity is 96%. Is this all normal? Does anyone have same issues?

    "Is this all normal?"
    Yes.
    "Does anyone have same issues?"
    What issues?
    Coconut indicates an approximate battery capacity, and 96% is excellent.  During testing and run-in, the MBP is charged and discharged, and a cycle count of 4 is appropriate.

  • Battery Health Degredation

    I've had this MacBook for about two weeks. In only three cycles the battery health is down to 95%. Is this normal or is this a bit soon for it to have lost 5%?

    No, it isn't normal. I had bought a new battery and in two weeks I was shocked to see it went down to 77%! I went to an Apple store to have it checked out, and they replaced my battery free of charge. Sometimes new batteries go faulty, so I would advise you to do the same. You paid enough for the computer already; you don't need to pay $100+ dollars for a new battery.

  • New MacBook Pro 2012 with battery health at 92%

    Hi everyone!
    Few weeks ago I bought brand new MacBook Pro (2012, 13"). After 12 cycles the battery health significantly decreased to 92%. Quite unexpected, isn't? Could you advise me what can be a problem? AC adapter, socket in my wall or something else?
    To answer your questions, I did not put the battery below 10% during this time.
    Thanks in advance for any hints!

    You have to take the computer to the Apple store to have it checked out.
    Genius Bar reservation:
    http://www.apple.com/retail/geniusbar/
    Best.

  • New iPhone 4 unlocked keep on restarting, and battery does not charge

    I have boght new iphone 4 8g unlocked in US last week, to use it back at home(Azerbaijan) but, phone keep on restarting, and battery charges strage way. Each time it restarts with friggency of 5 mins, it shows different procetage of battery charge. Could you please advice what can i do ? And how to check what is the problem?

    Reset, Hold both Home and Power buttons until the iPhone restarts itself.
    Clean iPhone Dock Port with a clean dry toothbrush.
    Try different, new USB cable.
    Try charging on Mac, PC USB or try different, new charger.

  • MBA early 2010, 200 cycles and 87% of battery health

    Hi,
    I've been using my macbook since April, so it's rather fresh. Battery life has become a bit worse that is pretty visible on the iStat. How can I improve my battery health without replacing it?
    I've seen some manual to make some special charging cycles, but cannot find it...
    Kal

    In a strict sense, that's a little (but not much) below what might be expected with that length of service and number of cycles on the battery, but much depends on other factors, not least being whether the MBA has been left, or used, for prolonged periods on mains power, or left discharged for a lengthy time, or even used in a pattern of full discharge/full recharge. These are the kind of factor which can deplete capacity and result in lower than optimum battery performance.
    Avoid regular full discharge/recharge, don't leave the unit plugged in for long periods, and routinely use the MBA away from mains, even if only for short periods before recharging to keep the battery well exercised, and that will help preserve remaining battery performance.

  • The battery for my Macbook Pro 13 "has only 121 cycles and is not charging anymore, my Mac is telling me that it is necessary to exchange it. You have any tips for me to find out what might be happening with my battery?

    The battery for my Macbook Pro 13 "has only 121 cycles and is not charging anymore, my Mac is telling me that it is necessary to exchange it. You have any tips for me to find out what might be happening with my battery?

    Guys, i am actually trying using a solution provided by the article shared by dominic23,
    It says "Another option is to get an ionizer to help the atmosphere in the workplace be more conductive and pull charges away from contact surfaces, including yourself."
    So in my home, we have such device that could clean the air using ion, and i am using it in my room...
    Result: BANG!!! The electric shock on my macbook has gone!! I don't really care about physics but somehow it works! You guys should give it a try.
    Thanks again dominic23

  • Battery has done 16 cycles and has 16% health!

    Hi,
    Im pretty certain that my battery is faulty, because ive had it for a year, always had it plugged in nearly all the time, and after 16 cycles the health shows up as 16% in both iStat pro and coconutBattery.
    Will apple replace it for me?
    Thanks
    James

    Only Apple can tell you if they will replace the battery, but good battery health means running down the battery at least once a month to "exercize" it.
    This is a good overview article:
    http://www.apple.com/downloads/dashboard/status/istatpro.html
    Note the links on the lower left and study the one about calibrating your battery. Proper calibration and exercise may bring that low health reading back up. Worth a try.

  • Cycle 23 but Battery Health 95%

    cycle 23 cut Battery Health 95%
    Battery  Problem  ????

    How old is your Mac? 1-2-3 years old?
    Batteries go bad even if the charge cycle count is low. They only last so long whether they are used or not. The last longer being used on a regular basis but not abused. Using them all the time and or leaving it connected to AC all the time will shorten it life span.
    Use it but don't abuse it.
    Message was edited by: Shootist007

  • Battery Health and ways to bring it up again?

    I've had my MacbookPro for a little over two months now and 31 cycles on it. However, I have already lost 7% battery health, leaving me at only 93%. I'm pretty sure that this is not good, and that the loss shouldn't be this rapid.
    I'm sure it has something to do with the way I use the computer. I leave it on quite often, which I know isn't a good thing, but had no idea that it would drain the battery like this. In some cases the computer is on for days at a time. I've gotten into a routine where each morning I turn it off for the bus ride to school, where I use it throughout the day. The night before it remains on so that I can quickly check things in the morning.
    I currently use my MacbookPro as a semi-desktop. I have it hooked up to an external monitor, and use a wireless mighty mouse and wired keyboard, which is primarily the reason it's on for such long stretches.
    Now that you have some background as to what I do with the computer I'd like to know if there is any way to replenish the battery health, or if that 7% is lost for good.
    I've read up on this calibrating of the battery business, and I'm going to try it this weekend (can't during the week because I need it fully charged for school each day).
    What exactly does this do? Does it actually replenish the battery health or just determine it's actual current percentage?
    I'm using the widget iStat Pro as my monitor of battery health.
    If any other information is required, I'd be happy to provide it.
    Thank you.

    dnovelta:
    use the battery frequently and lightly for best longevity. Apple states "An ideal use would be a commuter who uses her MacBook Pro on the train, then plugs it in at the office to charge."
    Read these:
    http://www.apple.com/batteries/
    http://www.apple.com/batteries/notebooks.html
    Hope this helps...
    Courcoul:
    Full Charge Capacity (which is what the specific battery clocked at the factory when first tested).
    Just a minor correction, but can be significant. Full charge capacity is not "what the specific battery clocked at the factory", it's a nominal value, i.e. a general property of the battery type, not that specific battery. Specific batteries have a range of full charge capacities (when new). In fact, it's not even measured, it's calculated - for the 15", it's a 60 Watt-hour battery (from the specs), and it runs at 10.8 V (printed right on the battery). Thus, with a basic formula (W = V x A), an algebraic rearrangement, and some simple math, 60 Wh / 10.8 V = 5.555 Ah = 5555 mAh (~5500 mAh, which iStat uses as the denominator for "health", although I have read that under Leopard iStat uses 5600 mAh, just a rounding difference). My 17" with a 68 Wh battery calculates to 6296 mAh, ~6300 mAh - my replacement battery actually started with ~6800 mAh in System Profiler.
    Just FYI...

Maybe you are looking for

  • Home Sharing Loading Forever and Windows 8

    So I thought I'd leave this here since I scoured this site via Google for answers and couldn't find anything that helped. I could not get iTunes Home Sharing to work on my Windows 8 PC (64-bit) in the last few months. My AppleTV would just sit there

  • How to embed custom search field in toolbar

    My organization wants to integrate the Zoom Search Engine by Wrensoft with RoboHelp 7. We want to embed the search input field for Zoom in the main toolbar of the Help window. The skin editor in RoboHelp does not provide an easy way to do this. I can

  • [ADF FACES] How to remove the "select" header in selection column

    Hi, Is there a way I can prevent the "select" header to be rendered (or customize this header) for the selection column in a af:table when using either af:tableSelectOne or af:tableSelectMany? Emmanuel.

  • Can I re-link graphics to a new location to update them?

    Is there any way to change the path when Updating an image in the library?

  • .asp/.aspx code erased or changed in DWCS4?

    I am a non-developer - a designer. We have a programmer who created a simple form in .aspx or .asp (not exactly sure which one) in Microsoft Visual Studio. When that .html page was opened in Dreamweaver CS4 he said the command "POST" was changed to "