Only hear 8 mins of audio after dvd being burned. help please

i keep trying to burn an avi file to idvd, but once its burned only the first 8 minutes of audio can be heard after that video looks fine but it becomes a silent film, i called apple and they said to go to advanced and click on delete encoded assets and that should fix the problem, but it didint. Has anyone had this problem and if so did you find a way to fix it?
id appreciate any help!
Thanks in advance

There's a known issue with 12 bit audio and iDVD. But its issue is syncing when encoded. It's unlikely that's the issue but it might. That's out of my area. See these topics: Re: Audio not in sync, Re: Audio sync problem when burning to DVD and So many audio problems.
They might have a suggestion you can try. Have you tried the disk image route yet?

Similar Messages

No loudspeaker audio after iphone4 screen replacement - help please

Hi All
I recently replaced the damaged screen of an iPhone4, when it all went back together everything worked fine except for problems with the loudspeaker, which worked perfectly before i started working on it. It is strange though that it will play ring tones perfectly well but no music, video, you tube etc
Tested speaker by changing ring tone - could hear through loudspeaker ok.
I am unable to increase (or decrease) the sound bar using the side control buttons (though could when testing with ringtones)
When making a call, switching to speaker works fine.
Occasionally hear the first two screen clicks when entering lock code.
have checked mute isn't switched on.
Works fine through headphones.
Have checked all settings regarding to the sound and all are set as expected.
Have cleaned all contacts with acetone
Have cleaned speakers with dry brush and air spray.
Have tried changing the speaker unit with no change (though i didn't think it would make any difference as the call on speaker worked)
This is now driving me nuts and i was only doing a pal a favour, and could really do without having to try and explain this to him. So any tips/advise or even guesses would be much appreciated.
Thanks
Andy

thats strange that sounds word on certain apps but not on others .... did u happen to try a phone reset // by holding power and home buttons until the device resets and you see the apple logo?

N00b mac user - dvd ripping & burning help please

Hi
I have got Mac the Ripper and bought Toast Titanium for my iMac but cant manage to get a copy done yet.
I have tried to rip 2 DVD's using Mac the Ripper and on both it has come up with a warning at the end saying the video has 'bad sectors"
I then open Toast and using the DVD_Video from Video_TS option and drag the Video_TS folder from the DVD I have ripped to Toast as instructed it starts compressing and then brings up a box saying
Quote:
" The drive reported an error:
Sense Key = ILLEGAL REQUEST
Sense Code = 0x24
INVALID FIELD IN CDB
I have also tried using Handbrake to rip the dvd's but that scans the dvd saying its scanning the titles but then just freezes
Anyone have any ideas please?? Its an Intel iMac.
BTW purely legal, making copies of ones I've bought for daughter so she can take on holiday with us
Thanks

Some DVDs especially those made by sony and disney are mastered with bad sectors on purpose as part of the copy protection process. Mac the Ripper is not very good when it comes to these discs. I have to use my wife's pc with dvd fab decrypter to copy these discs. It is not the fault of the imac by any means. Every disc I have copied except for those made by sony or disney since I got my imac have been perfect. Toast could be giving an error because the file from Mac the Ripper may not be playable. Try playing them first with the dvd player or VLC player to see if they work. If they do, make sure you have updated toast to the latest version. Good luck>

HT2045 I bought a song, which played on my computer. When I tranfered it to my IPod,only the first 30 seconds of the song plays. Help please!

Please help me. I bought a song which played on my computer, but when I tranfered it to my IPod, only the first 30 seconds of it will play. Help please. Is there a way I can contact Apple to complain, because I'm not paying $1.29 for the first 30 seconds of a song. Or is there anyway to fix it? (note: i have already synced my Ipod and it has the latest version of ITunes)

Im having a similar promblem! Only its doesnt work on my Itunes library and the song ends at 49 seconds. Have you fixed your problem yet?
p.s. my discussion is on the following page but no one has responded yet as I only just posted it.
https://discussions.apple.com/thread/4097402

Reset phone to factory settings to remove unwanted email addresses from autofilling. Now trying to only sync real contacts, photos, and apps from backup. HELP PLEASE! :)

Reset phone to factory settings to remove unwanted email addresses from autofilling. Now trying to only sync real contacts, photos, and apps from backup. HELP PLEASE!

All of this should be on your computer as you should be syncing regularly to your computer.. Just sync it back.
iPhone User Guide (For iOS 4.2 and 4.3 Software)

On external monitor: GOOD. after render & dvd: BAAAAD. help, please!

Hi, I edited a 60i NTSC video from a canon XL2, and it looks fine on the external monitor (TV), the FCP preview and everything. It even looks good when I export a QT mov with no compression.
But as soon as I burn it on iDVD and play it on a DVD player, the whole interlacing business goes terribly, terribly wrong.
I've tried all possible exporting settings, but it doesn't work. Should I de-interlace the clips? I've gathered from reading the forums that it might help, but it sounds like a desperate solution, since the text should be interlaced but not the video?
I mean... what did I do wrong? Isn't ot supposed to just work straight-through with the NTSC DV Easy Setup and changing only to "None" on the compressing settings at export?
Any help, please? Anybody?

oh, OK.
For exporting, I used the Export>Quicktime movie, just like you said, using the current setting (i.e. Compression:None)
The DVD player was connected to a PAL TV, but it's OK because the DVD player can read anything. I know because I've watched NTSC as well as PAL dvd movies before.
The Canon XL2 the Mac is connected to, via Firewire, is NTSC, connected via RCA to the PAL TV. Which means the signal I'm watching is Black & White... (I know this sounds WEIRD)... but it's O.K. because what I'm really checking as I edit is the interlacing problem that I got when playing the DVD on the dvd player.... : the BAD problem.
How bad? Really bad. Any sudden movement, or panning of objects with vertical lines, like a painting or a building looks all wobbly and curvey and blurry and wrong, which is unnacceptable for the project I'm doing, as it is a professional work (Meaning that I'm charging money for it, despite the crazy assemble of different products and formats I'm using).
I've gotten things that look good before, but never on Final Cut Pro.. I'm new to the program, and to Mac, and this is the first video I'm exporting to a DVD on this platform.

HT204291 I can only hear the instant video with AirPlay. Can anyone help

I have used airplay before to watch instant video from my iPad but for some reason I can only hear the video now and see the movie icon pop up once. Does anyone know what I need to select in order to see the actual movie

Welcome to the Apple community.
I'm not really sure what visor is, I am assuming it is an app or a webpage that you are watching on your iPad and trying to airplay to the Apple TV.
Websites and third party Apps need enabling before they will allow AirPlay of Video content. Some Website/App developers have not enabled their products, some simply haven't got around to it yet, others have stated that they won't be enabling AirPlay (likely as a result of licensing issues).

After effects and photoshop ,,,help please

hi all
can anybody help please.
ive been making a short film with my son and putting some basic effects in, just for a laugh.
i noticed an effect on ADOBE TV that was done by Gareth Edwards in his movie MONSTERS which i thought would be good to try out in my film but i carnt get it right,,
here is the link to that effect... http://tv.adobe.com/watch/customer-stories-video-film-and-audio/monsters/
its the effect where he changes the menu board in a cafe to one of his infected area signs, he allso changes a few other signs.
in the video he say that he exports a still frame from after effects into photoshop and puts on his image {with a few tweaks her and there}, when hes got it ok in photoshop ,it some how updates in after effects??
can any please help ,thank you

It's a simplified explanation of the process. He left out explanations of motion tracking and perspective matching that were most certainly required for the shot being discussed.
If you are doing the same process to a static, locked off shot, with no foreground objects passing in front of your sign, it would be very possible to create a single frame in Photoshop and just layer it over your scene in AE. But once the camera moves, you will need to understand Motion Tracking. If objects pass in front of the replaced component, you will need to understand Masking.

Broken Bonjour with Canon MF4350d after 10.6 upgrade - Help Please.

I have been using a Canon 4350d with no problems with 10.5.8 - including Printer Sharing (Bonjour). Now, after updating to 10.6 (now 10.6.2) I can still print fine, but I have lost all Printer Sharing. All settings appear to be right, and my other macs appear to be printing through the one connected via USB to the printer, but it never goes through. HELP Please. Thank you.

According to the UFR2 User Guide on page 2-8, the driver can be removed from the Mac by trashing the following folders. Note that you should delete the print queue first, by opening Print & Fax, selecting the MF model in the Printers list and pressing the minus button.
System Volume > Library > Printers > Canon > UFR2
System Volume > Library > Launch Agents > jp.co.canon.UFR2.BG.plist
System Volume > Library > Printers > PPDs > Contents > Resources > en.lproj > CNTD**Z*2.ppd.gz
(where * indicates the printer model and 2 indicates the language of driver used)
With these files removed you can then empty the trash, although you may have to open Activity Monitor and stop the 'UFR II Backgrounder' service before you are able to remove all the files from the trash.
With the v2.10 driver removed you are ready to add another driver. However you need to be aware that the v1.80 driver cannot be used on 10.6. If you were using it previously then it would suggest that the 10.6 Mac was an upgrade from 10.5 rather than a clean 10.6 install. On a clean 10.6 Mac, then v1.80 driver will not operate correctly.
What you may be able to do is have the v1.80 driver installed on a Mac running Leopard and shared. You may then be able to use the v2.10 driver on the Snow Leopard Mac's to print to the Leopard share using the v1.80 driver. Note that I haven't tried this so I cannot say if this will work for you. Personally I always ensure I get a printer with Ethernet or wireless support so that I can avoid printer sharing...

Mega 865 DVD RW drive - HELP PLEASE

Hello again been a long time since i have been here. Anyway the reason im back is that my DVD RW (NEC 2500A) is getting "Power callibration" errors when burning .. tried all the new firmwares etc so looks like the drive is dead..
Now my question is .. what drive can i get to replace is .. i.e is the NEC 3550A good etc... or is there better onces...
I remember about a year or so ago there was a list on here but couldnt find it ( i did try and search)
Any help please
Thanks

"Power calibration" errors can be caused by a failing drive, or by using bad media. also, have you tried using a DVD head cleaning disc, in case the lens is dirty?

I bought a gift card n reedem it , showed the credit but not allowed me to download games apps , i can only use it to buy film and music . Anyone help please !!

Anyone help please !!

The devices are not registered in Malta as such, it's your Apple ID that is registered in a country other than France, namely Malta. You can only use gift cards from France when your iTunes Store account is registered for use in France. That requires a credit card issued to a French bank and billed to an address in France. I'm afraid there's nothing you can do with the card other than find a user in France who would like it.
The iTunes Store in a country is intended only for use by that country's residents, and only while they are in the country. To use the iTunes Store in a country you need a credit card (or other card type if acceptable in a country) issued in that country, billed to an address in that country, and also be physically present in that country when using the store. You are also restricted to waiting 90 days between country changes.
E.g., "The iTunes Service is available to you only in the United States, its territories, and possessions. You agree not to use or attempt to use the iTunes Service from outside these locations. Apple may use technologies to verify your compliance. - http://www.apple.com/legal/itunes/us/terms.html#SERVICE"

Z10 won't complete setup after device software update, help please.

Help please, cannot complete phone setup ater performing software update using Blackberry Link.
Sequence of events;-
Phone recognised by Blackberry Link.
Reload device software selected - updated version 10.0.10.90 available.
Get update - software appears to load correctly then Z10 unplugged.
Phone reboots, Welcome to Blackberry, English(UK) ticked, swupe left.
No SIM card available, swipe to WI-Fi.
Password entered for home network and confirmation screen shows connected.
Agreement Screen - Country changed to United Kingdom(English),
at bottom of screen under I agree to the Blackberry SLA....
the 'I Agree' and 'I Do Not Agree' buttons can not be selected and
after a short delay Unable to connect screen appears.
Pressing 'Settings' goes back to Wi-Fi Networks page with
confirmation that connection is good and round we go again.
Having performed software update several times as above and also from
www.BlackBerry.com/updates by following forum posting at
http://supportforums.blackberry.com/t5/General-BlackBerry-10-Smartphone/How-
to-Reload-your-Blackberry10-OS/td-p/2187545
and getting the same result each time I would appreciate help to resolve this issue.
Solved!
Go to Solution.

Try finding a different open free Wifi hotspot to perform the setup.
It sounds like the device is never connecting to your WiFi to complete the setup.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Poor image quality after DVD is burned.

Hi,
Project is fine in FCP and in iDVD before burn but when the burned dvd is played some of the images have lines or large pixels. The large pixels are very obvious in bright or white shots. Haven't had any other problems with the Mac for 4 years.
Any suggestions or solutions?
Thanks

Hi
a. Can it be so that Your movie is in PAL (25fps) and iDVD in NTSC (29.97fps)
No good way to do it - I use JES_Deinterlacer to convert
b. I do from FinalCut Pro 6
• Export out as a QuickTime .mov file
• Not selfcontained (not important but saves time and space)
• NO QUICKTIME CONVERSION - IMPORTANT !
This file I import into iDVD
Else read my list on DVD-Quality
1. iDVD 08 & 09 has three levels of qualities.
iDVD 6 has the two last ones
• Professional Quality (movies up to 120 min.) - BEST
• Best Performances (movies less than 60 min.) - High quality on final DVD
• High Quality (in iDVD08 or 09) / Best Quality (in iDVD6) (movies up to 120 min.) - slightly lower quality than above
2.Video from
• FCE/P - Export out as full quality QuickTime.mov (not selfcontaining, no conversion)
• iMovie x-6 - Don't use ”Share/Export to iDVD” = destructive even to movie project and especially so
when the movie includes photos. Instead just drop or import the iMovie movie project icon (with a Star on it) into iDVD theme window.
• iMovie’08 not meant to go to iDVD. Go via Media Browser or rather use iMovie HD 6 from start.
3. I use Roxio Toast™ to make an as slow burn as possibly eg x1 (in iDVD’08 or 09 this can also be set)
This can also be done with (Apple) Disk Util tool.
4. There has to be about or more than 25Gb free space on internal (start-up) hard disk. iDVD can't
use an external one as scratch disk (if it is not start-up disc).
5. I use Verbatim ( also recommended by many - Taiyo Yuden DVDs - I can’t get hold of it to test )
6. I use DVD-R (no +R or +/-RW)
7. Keep NTSC to NTSC - or - PAL to PAL when going from iMovie to iDVD
8. Don’t burn more than three DVD at a time - but let the laser cool off for a while befor next batch.
iDVD quality also depends on.
• HOW much free space is there on Your internal (start-up) hard disk. Go for approx 25Gb.
less than 5Gb and Your result will most probably not play.
• What kind of movie project You drop into it. MPEG4 seems to be a bad choice.
other strange formats are .avi, .wmv, .flash etc. Convert to streamingDV first
Also audio formats matters. I use only .aiff or from miniDV tape Camera 16-bit
strange formats often problematic are .avi, .wmv, audio from iTunes, .mp3 etc
Convert to .aiff first and use this in movie project
• What kind of standard - NTSC movie and NTSC DVD or PAL to PAL - no mix.
(If You need to change to do a NTSC DVD from PAL material let JESDeinterlacer3.2.2 do the conversion)
(Dropping a PAL movie into a NTSC iDVD project
(US) NTSC DVDs most often are playable in EU
(EU) PAL DVDs most often needs to be converted to play in US
UNLESS. They are plabacked by a Mac - then You need not to care
• What kind of DVDs You are using. I use Verbatim DVD-R (this brand AND no +R or +/-RW)
• How You encode and burn it. Two settings prior iDVD’08 or 09
Pro Quality (only in iDVD 08 & 09)
Best / High Quality (not always - most often not)
Best / High Performances (most often my choise before Pro Quality)
1. go to iDVD pref. menu and select tab far right and set burn speed to x1 (less errors = plays better) - only in iDVD 08 & 09
(x4 by some and may be even better)
2. Project info. Select Professional Encoding - only in iDVD 08 & 09.
Region codes.
iDVD - only burn Region = 0 - meaning - DVDs are playable everywhere
DVD Studio pro can set Region codes.
1 = US
2 = EU
*unclemano wrote*
What it turned out to be was the "quality" settings in iDVD. The total clip time was NOT over 2 hours or 4.7GB, yet iDVD created massive visual artifacts on the "professional quality" setting.
I switched the settings to "high quality" which solved the problem. According iDVD help, "high quality" determines the best bit rate for the clips you have.
I have NEVER seen iDVD do this before, especially when I was under the 2 hour and 4.7GB limits.
For anyone else, there seem to be 2 places in iDVD to set quality settings, the first is under "preferences" and the second under "project info." They do NOT seem to be linked (i.e. if you change one, the other is NOT changed). take care, Mario
Yours Bengt W

Sync Goes Out on Several Clips AFter DVD Pro Burn

This problem existed on several clips that were relatively close together in timeline. As this is a 52' video with many cuts and multi-tracks, I tried using the audio mixdown render in FCP and then burned again. There was an improvement, but I still have one clip out of sync.
Any ideas on what else to do?
I'm exporting to QT Conversion and encoding as high as I can push the DVD Pro encoder - to around 7.2.
FCP 5
DVD PRO 4

I'm correcting what I reported earlier. The sync goes out on the output from FCP. This is NOT a DVD STUDIO PRO problem! I'm using the QUICKTIME CONVERSION option on the output.
I'll repost in the FCP forum.

Some Audio is nothing being burned onto dvd.

please excuse the newbie question BUT....
i have audio on A1 and A2. They are not coming through when i play my dvd on a player hooked up to my television but it does sound when i play it on my G5's DVD PLAYER.
I also have audio on A5 through A10. That audio sounds on both.
does the a1 and A1 attachment on the left have anything to do with this? i have a screen shot i can send via if that will help. i realize my description may be cryptic.

I know you've said you've solved this, but it sounds as if you are using different audio tracks for different audio channels? they are there to allow you to use alternate audio, not split stereo left and right.
All of your audio channels (left and right) go into one of the Audio tracks.

Only hear 8 mins of audio after dvd being burned. help please

Similar Messages

Maybe you are looking for