ONS 15216 and 10G

Dear Sirs!
Can I use 10G DWDM modules (for example DWDM-SFP10G-30.33=) with 15216-MD-40-ODD= Mux/Demux?
And if it possible, can I use few 10G SFP+ modules and few 1G SFP modules together?
And if it not possible, what cisco Mux/Demux I must use, for 10G DWDM? (I need minimum 8 channel)
Thanks!
Helping seriously ill children, all together. All information about this, is posted on my blog

Hi Angelo,
I am currently working on a project with Catalyst 6500's using the DWDM XENPAKS and the Flexlayer. We have tested this at line rate and it works fine. We have a combination of SUP720 with the 4 port 10G cards and the newer Sup with dual 10G ports. We are also using a combination of 8 port and 2 port OADMs, with splitter combiners... good solution...
John ...

Similar Messages

Sorting in 6i and 10g reports

Hello All,
I am running 6i and 10g reports against a 10g database.
I ran one of the 6i report and it generated a report in one sorting ordear
and when i ran the same report on 10g ,it generated the report in ddifferent order.
Both the reports r run against the same 10g database.
The order by clause on the columns of the records r identical.
Now i wanted to understand how it is sorting in different orders in both 6i and 10g reports?
Thanks,
Ranz

Hi,
Please note the fact that 6i Reports is not certified to work with 10g Database. Hence it becomes impossible to address the sorting behavior of 6i Reports, though there is nothing different in the way it works. I would suggest you to use 10gR2 version of Reports services with 10g Database which is certified and supported. Thanks for your understanding.
Regards,
Anand

Dflt report in 6i and 10g

Hi
I am trying to get a tillslip to print correctly after converting from reports 6i to 10g. The problem i think is that the outputfile generated in the 6i version is diffrent from the output file in 10g. The 10g version looks similar to postscript while the 6i output file does not mean anything to me.
If i open the 6i test.dflt file it looks something like: =c0c1c32R
If i open the 10g test.dflt file it looks something like:
%!PS-Adobe-3.0 %
%Creator: Oracle Toolkit 2 for Motif 10.1.2.0.2 PRODUCTION
Using the 6i output file i can print the tillslip correctly in both the 6i and 10g environments. Using the 10g output file all the char in the output file prints including the comments (the %!PS-Adobe-3.0 % bit also)
Any ideas how to get the output file the same. All report settings (DESFOTMAT, DESTYPE, ...) are the same. The dflt.prt file only differs as follows:
printer "dflt"
height 66
width 80
after page control(L)
return "" (this line in 6i file is: return "M" )
linefeed control(J)
Any ideas will be helpfull. I have tried creating the report as a .rtf, .pdf and .ps file and all of them print with the code inside and not just the tillslip info.
Thanks

Hi
I afound that the problem is that the app server does not know about the printer as it is connected to a users PC. Thus when using the dflt desformat it selects the default printer language of the App Server printer. This is the reason why the files are diffrent.
If I understand everything the process should be:
1 - Run the report from forms (on app server).
2 - Write the report to a file on App Server and then transfer the file to the user PC.
3 - Send file correct printer on the user PC.
The problem still remains on how to create the correct file which can be send to the printer connected to the users PC as the driver of the correct printer is not known too the App Server. The printer still prints the file incorrectly as the file is not created using its drive as what the case was when running it in 6i.
Setting the MODE to character (which will enable you to provide a .prt file if you had one to give) will not work as the report contains an image.
Regards
Edited by: hfp843 on Sep 17, 2008 2:28 AM

Occasional ora-6502 using forms 6i and 10g

Hi all.
We have been experiencing some weird and unexpected ora-6502 errors in some of our forms 6i modules running against 10g (rel 1 or 2).
Forms modules are correctly functioning and for some reason, one day an ora-6502 error suddenly pops up.
Now the weirdest thing is that after you put some messages on the trigger, so you can track down where the error is coming from, it disappears.
I know that this may sound hard to believe, but it has happened several times. All we do is put some message built in, recompile all, and the error is gone (for a while).
So my questions are:
- Is this a known issue beween forms 6i and 10g Db?.
- Is there a patch on Metalink ( we use Forms [32 bits] Versión 6.0.8.26.0 (Producción))
- A workaround?
and most important
- Have anyone been exposed to a similar situation?
Regards, Luis ...!

Now the weirdest thing is that after you put some messages on the trigger, so you can track down where the error is coming from, it disappears.Sounds like the form has not been "clean compiled" against the server on which it is running. Try a "Compile All", which causes all previously compiled program units to be compiled fresh.
Or even better, clean out all the compiled code from your fmb before compiling the fmb on the server where it runs.
See this topic: Re: Why does this happen - find ';', replace with ';'?

Designer 6i and 10g on the same machine?

I have Designer 6i and corresponding repository on my machine.
The problem with 6i I can't save diagramm in HTML format
I believe I can save in HTML format in 10g or other?
Can I install on the same machine 10g designer?
should I configure new repository?
TIA

See my update on your earlier question.
As for running 6i and 10g on the same machine, yes you can do it. You just have to install them in separate Oracle Homes, and be careful when you tell them which version of EXP and IMP to use. There is one MAJOR caveat, however. They cannot use the same Designer Repository - 6i client won't talk to a 10g repository and 10g client won't talk to a 6i repository. You can upgrade a 6i repository to 10g with the RAU, but take a backup before you do - the only way to go back is to restore your backup. Besides, I think that if you upgrade to the last supported version of Designer 6i (you should be able to get it from MetaLink) you will get the Publish Diagrams utility.
Frankly, my opinion is that there is only one reason to stay on 6i - if you need to generate and support 6i client/server Oracle Forms. If you don't use Oracle Forms, or if you have moved on to Web Forms with the middle tier Forms Server, I'd recommend an upgrade to Designer 10g and Developer 10g.

Calling shared objects in unix from Forms 6i and 10g

I would like to know how to call shared objects in unix from Froms 6i and 10g. Can anybody help in this regard? Your help is very well appreciated.

Hi,
Do you have any 11i instance where those custom forms are used? If yes, you will have to copy those forms from 11i to R12 instance, open the forms using Forms 10g builder, compile it and upload it back to the server.
Note: 427879.1 - How To Customize And Compile An Application Seeded Form (FMB) Or Library (PLL)?
Note: 743490.1 - Customization in Oracle Applications
Note: 563258.1 - How To Upgrade 11i Custom Forms And Reports To R12
Regards,
Hussein

Using get_application_property(CONFIG) in 6i and 10g

Hi,
for a short time, our application has to run with 6i and 10g at the same time. We have to use the new constant CONFIG also in 6i. How can I mask this constant that it works correctly. Implementing it like this doesn't work:
PROCEDURE gui$new_session
IS
pl_id ParamList;
form_name varchar2(100);
lo_connect varchar2(250);
lo_url varchar2(200);
lo_conf varchar2(50);
co_config CONSTANT NUMBER := 'CONFIG';
BEGIN
form_name := replace(pdb_anwendung.get_anw_exe('PRAG_MENUE45'), '.FMX','');
IF get_application_property(USER_INTERFACE) <> 'WEB' THEN
RUN_PRODUCT(FORMS, form_name, ASYNCHRONOUS, RUNTIME, FILESYSTEM, pl_id, NULL);
ELSE
lo_connect := get_application_property(USERNAME)||'/'||get_application_property(PASSWORD)||'@'||get_application_property(CONNECT_STRING);
lo_conf := get_application_property(co_config);
lo_url := 'javascript:window.open("/forms/frmservlet?config='||lo_conf||'&form='||form_name||'&userid='||lo_connect||'","","location=no,toolbar=no,menubar=no,status=no,");self.close();';
WEB.SHOW_DOCUMENT(lo_url,'_blank');
END IF;
END;
Unfortunately, I can't set the constant CONFIG directly into get_application_property (what is working properly used directly in 10g) because then I get a compilation error in 6i. Can somebody help me?
Regards,
Heike

Clearly...
co_config CONSTANT NUMBER := 'CONFIG';... won't work because you are assigning a varchar value to a number. CONFIG (without the quotes) is a built-in constant in Forms 10g that has a value of 221. So you could try this (notice there are no single quotes)...
co_config CONSTANT NUMBER := CONFIG;... but I doubt that will compile in 6i as CONFIG won't be defined. So maybe you could use...
co_config CONSTANT NUMBER := 221;It's bad practice to hard-code a value like that though.

Ran a previous version of FF, then closed and ran regular (5.0) version, but some add-ons, toolbars, and other stuff has disappeared. How can I get this stuff back?

I have been running 5.0 great for a while now, but today I tried downloading and running FF 3.6. As it was opening it stopped responding, but then I tried to force quit but then it worked and loaded up the pages I had open on 5.0 when I closed it.
I then closed the 3.6 version and ran the 5.0. I noticed a few things were gone or different...
~Several add-ons/extensions and toolbars were gone. Some of them were: Adblock Plus, Read it Later (and all its saved pages), Stumble Upon toolbar.... and more I am not sure of...
~Some of the saved sessions in my Session Manager add-on were gone.
~FF 5 seems to not be asking if I want to save my pages whenever I quit.
~The settings for how my tabs appeared has changed also... Like the color of text and where a new tab goes when I click on a link (to the right of the current tab or all the way to the right)... I am not sure if this is because of an associated add-on/extension being deleted.
UPDATE: I checked my profile folder and all of the extensions' data is all still there but FF5 is just not reading it correctly. (like adblock plus... I see the folder for it but FF5 doesn't have it on the add-on manager page when I run FF5) (The stumble upon toolbar folder is also in my profile folder but is not showing up in View->Toolbars when I actually run FF5)
Any help would be extremely appreciated.
Thanks!

Thanks but I don't think this will help. Like I said, all of my add-ons were working fine and compatible until after running a previous version of FF. I am sure they are still compatible, but they are not working at all.
I even checked my profile folder and all of the extensions' data is all still there but FF5 is just not reading it correctly. (like adblock plus... I see the folder for it but FF5 doesn't have it on the add-on manager page when I run FF5)

Query using Materalized view in oracle 9i and 10g

Hello
There are snapshots (materialized view) used in my application. We have recently migrated from 9i to 10g release 2 database.
After migration i have observed explain plan of query which is using materialized view and i found in 9i oracle treating materalized view as table. In 10g oracle is considerting it as MVIEW only (MAT_VIEW ACCESS BY INDEX ROWID). However in 10g cost of query which is using materialized view is much higher than 9i. And execution time is also random.
Can anbody pls. expalin diff. of materalized view access in oracle 9i and 10g.
Thanks

can you post your query with explain plan for both 9i version and 10g version.
Thanks,
karthick.

At least 6 differences between Oracle 9i and 10g with complete understan

Hi 2.
At least 6 differences between Oracle 9i and 10g with complete understanding of each difference .
cheers

Hi,
Forum thread already opened by you
check what is the major difference between 9i and 10g
regards,
kaushal

Running 8i and 10g on same UNIX server

Greetings,
I am a developer playing DBA, so please forgive me if these are elementary questions. I have no DBA support.
I have a Solaris 8 server currently running operational software using 8i. My requirement is to load and test 64bit 10g without interfering with the operational system, then test the s/w. Later, I need to switch from 8i to 10g with little or (preferably) no downtime. It would be nice run the two in parallel before the switchover.
I have a duplicate setup in the development lab, which is what I am working on right now.
I was able to get 10g loaded without any apparent problems. However, when I try to run 8i and 10g, the listeners conflict.
After reading through various forums this morning, I have a few questions that I am hoping someone can answer.
1. Oracle 8i is owned by user oracle. I loaded 10g as user ora10g. Should I have loaded 10g as user oracle? If so, how do I keep it from overwriting critical 8i files that are in /usr/local/bin, etc?
2. Oracle 8is ORACLE_HOME is /usr/opt/oracle. 10gs is /export/ora10g. Does 10g need to be in /usr/opt/ora10g? If so, can I set up a link to simulate this, or do I need to reload?
Thanks in advance,
Linda

Won't say much about the platform (solaris) aspect here but anyway...
1. You could and sometimes should have a different oracle software owner user for installing/managing software, either is ok. You also might want a different group to own the oraInventory (software catalog).
You can always enter somethng other than default when prompted by root.sh - why not e.g. /home/ora10g/bin?
2. I dont think it needs to be installed anywhere, but /export is a bit unusual isn't it? Used for nfs etc.

Active ODP when both 9 and 10g are installed...

I have both ODP 9i and ODP 10g (along with the Oracle 10g client) installed on my workstation. How does one set up one or the other to be the 'active' ODP client? For instance, I have an application that I developed under ODP 9i... because I developed this under ODP 9, I want it to run under ODP 9 on my or anyone else's workstation. However, when I view it in the Visual Studio 2003 IDE, it shows ODP 10 as the 'active' client. Even when I run it, I find it is using ODP 10 (I know this because I have a Help...About screen in my runtime that displays the loaded assemblies) Even if I install it on a plain workstation (i.e. no Visual Studio 2003) with both 9i and 10g installed, and even though it was fully compiled using 9i, it still shows up as using the 10g ODP client. I don't want that at this time - if I compile it under 9i I want it to use Oracle 9i... Otherwise, what is the sense of having both clients on the machine?
So.... bottom line... is there a way to set one of the ODP clients to be 'active' even though both clients are installed?
Thanks in advance.
Tom

Hi,
By default, ODP installs publisher policy files to redirect to the latest version of ODP, which would make an app compiled with 92x odp use the 10x odp instead. If you dont want that to happen, delete the oracle.dataaccess publisher policy files from the GAC, but then you'll get no redirection at all. IE, you'll have to have the exact version the app was compiled with on that box to run the app.
Or, as msolnit pointed you to above, there's an article on the MS site that explains more about it, and other ways to prevent it on a per-application basis (see the Bypassing Publisher Policy section of that article)
Cheers, hope it helps.
Greg

I want to reinstall my operating system,How can I back up all my add ons, extensions and personas for reinstallation when Im done?

I want to reinstall my operating system,How can I back up all my add ons, extensions and personas for reinstallation when Im done?
Im using fire ftp,downthem all,wot , antiporn pro,and various personas.
I dont want to renstall them all one at a time, rather I would like to ireinstall a back up like I do with my bookmarks,
Is this possible??

See this support article. <br />
https://support.mozilla.com/en-US/kb/Backing+up+your+information

When I downloaded the new Firefox about a week or two ago all my bookmarks, and add-ons disappeared and I want you to give them back to me asap?

When I downloaded the new Firefox about a week or two ago all my bookmarks, and add-ons disappeared and I want you to give them back to me asap?

You shouldn't wait that long to ask advice. Firefox only keeps a (rotating) backup of bookmarks for the last 5 days that you started Firefox. So you may be out of luck.
You can check that you still use your old default profile that had your bookmarks.<br />
* http://kb.mozillazine.org/Recovering_a_missing_profile
* http://kb.mozillazine.org/Lost_bookmarks
* http://kb.mozillazine.org/Locked_or_damaged_places.sqlite
For the extension, see "Corrupt extension files": http://kb.mozillazine.org/Unable_to_install_themes_or_extensions
If you see disabled extensions that are not compatible on the next start in "Tools > Add-ons > Extensions" then click the "Find Updates" button to do a compatibility check.

Oracle 9i and 10g in one computer

Could I install oracle 10g in computer where 9i is instaled. I want that both oracle is instal and test oracle 9i and 10g. Could I run oracle database 9i and 10g together and I use both of the database?
Thanks for answer.
Rafal Dmitrowski

I would also suggest caution if you have a Windows server. While it is certainly possible to have both running, there are some issues with separate 9i and 10g homes on a Windows machine, things like the Oracle Home Selector doesn't work with 10g Oracle Homes. I wouldn't be overly concerned if you are dealing with development laptops, but I would make sure to do some testing before installing 10g on a production server with 9i already installed.
Justin
Distributed Database Consulting, Inc.
http://www.ddbcinc.com/askDDBC

ONS 15216 and 10G

Similar Messages

Maybe you are looking for