Open NAT xbox live problems

Ok I am really getting tired of this. I jsut want my NAT to be open. Right now it is strict. My Lynksys router is a WRT110. I have tried multiple ways to get it to open. Can someone please give me a detailed guide? And if you NAT is open could you maybe show me pictures of yours if your NAT is open? I am willing to use teamviewer.
Thank you for your time.

Who is your ISP....?
If your ISP is DSL then,you have to convert the modem into the Bridge mode first.After converting the modem into the bridge mode,configure the router with PPPoE settings and open the required ports on the router.
If your ISP is not DSL then,try the following settings...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your XboxIP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Similar Messages

Open NAT / Xbox One

I have Fios Quantum with a Actiontec MI424-WR router Rev. I, believe it is the most recent action tech, the router is black and red.
I can't get an Open NAT, it is set to strict. This is preventing me from joining Xbox Live parties and playing online with friends.
Can anyone assist me with how to get an open NAT?
Thanks.

It is an issue with the router and not the xbox, I can tell you that. Do you have to Xbox's connected by any chance? That would make NAT not be open9 out of 10 times. The only other options I can think of are.
-Enable UPnP (Disable DMZ & port forwarding)
-Setting router firewall to Low
Here's a good guide on the Xbox forums: http://forums.xbox.com/xbox_forums/xbox_support/xbox_360_support/f/9/p/1625236/4199656.aspx#ARMfirew...

Lumia 800 : XBOX Live problem

Greetings everyone. Recently i bought a Lumia 800 device. I wanted to use the XBOX LIVE feature, but it said that xbox live is not available in my country / region. I live in Croatia and my phone operator is T-Mobile. When will XBOX LIVE feature be available in my country ? Thanks in advance, robi2595.
Solved!
Go to Solution.

Hey Robi2595, Welcome to the Nokia Forums!
Im afraid Xbox Live does not support croatia, we are not able to provide any further specific information, however I suggest that you contact Xbox Live support to get a more detailed answer to your query.
You can either go to their forum or contact them via twitter.
Thank you for your post!
Sheldrick
Press the 'Accept As Solution' icon if I have solved your problem, Kudos my post if my advice has helped you!

Alright, Xbox live problems.

A friend of mine is using the Linksys 10/100 5 port ezxs55w ver. 4.1 as a hub/router for his xbox live.
Ive manually put in the IP, DNS, DHCP, subnet mask, into my XBOX360, and when i test the connection it works. Well, and we are not sure if its the hub, or a problem with microsoft, When i attempt to download an update, the update stalls, times out, and tells me to check my internet connection. I know, for a FACT, that my connection is fine, and when i test it on my xbox, i receive a green light, and the connection is okayd.
Can anyone help me? Ive posted on forums across the net, Emailed Microsoft support yesterday, and been on AIM with a tech support buddy for 4 hours. If this is a microsoft problem, not a problem with the hub, please, let me know, and ill focus my efforts on them.
Thanks much for your time,
-Nathan

It's most likely not an issue with your switch... look into whatever device is providing the DHCP settings, and what it's giving the Xbox. As you've already pointed out, the manual IP configuration works fine.
Ps: PS3's rule
Also... The internet connection might appear to be fine, but if it's disconnecting intermittently it can really mess up firmware/updates if they don't have a interruption recovery.
Message Edited by gyrfalcon on 07-17-2009 09:43 PM

Linksys e2000 nat xbox live

i have an e2000 router and a wireless n xbox 360 game adapter. when i go to test connection it says my NAT type is set to moderate. how do i change that to open?

Try the instructions here.

Opening NAT (Xbox)- Airport Express

Ok so I need some help here, Ive been trying to re-open my nat type on my xbox but I just cant get it. I have tried the solutions in this thread: https://discussions.apple.com/message/8682893#8682893 but I either cant understand exactly what to do (the layout is a bit weird) or its just not working. I have tried to bridge my airport but that just disabled my internet entirely. Also, Im not too savy with Apple, I just dont get it. Im good with Windows so I may need noob friendly advice.

Very detailed instructions are provided in the article How do I use port mapping?

Xbox live problem?

Alright, I got a brand new network adaptor for the Xbox 360 so that I would be able to access the online benefits and such. Now, as soon as I plugged it in, it went orange...saying it was not connected...and I checked for all services...and my linksys one wouldn't pop up. I called Xbox for nearly a half hour...and I got nothing accomplished.

(continued)
so basically, I have searched and searched, and I cannot find an answer for this problem. I have another little wireless adaptor for another computer in a VERY close proximity, and it works wonderfully! Yet this one hates me it seems....
I have a new Xbox 360 with the network adaptor, bellsouth DSL which works well, and a WRT54GS model router....
Any help???

E2000 Constantly disconnects from XBOX Live

I'm not having an NAT issue, but my e2000 is constantly disconnecting from XBOX Live. About every 3-5 minutes I get disconnected. My wireless is working perfectly, this is only an issue with XBOX Live.
I've followed all the examples on the forums here, like:
http://homecommunity.cisco.com/t5/Wireless-Routers/Need-HELP-to-change-NAT-type-to-open-on-Linksys-E...
and
http://homecommunity.cisco.com/t5/Wireless-Routers/Open-NAT-xbox-live-problems/td-p/337375
and I have double checked every setting. I'm not sure what is causing this issue.
I've set the MTU, unchecked UPnP, entered port forwarding range to XBOX's static IP address, and set the DMZ to my XBOX's MAC address.
So, what is causing my router to constantly disconnect?

Try the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] Then Click on wireless Tab select Channel Width to 20 MHz only and Channel to 6, 9, and 11. Click Save Settings....
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

Opening ports for my xbox live NAT type

I need help on how to open the ports needed to successfully pull my NAT setting from "strict" to "open" on XBox Live. Those of you here that have it, probably know what Im talking about.
The ports I need to open are the following:
UDP 88
UDP 3074
TCP 3074
Ive tried already, but it didnt work. I think I did something wrong.
Thanks

Hi AEX,
First thing you have to make sure is that, you have to assign a static ip address on XBOX like 192.168.1.10, with subnet mask of 255.255.255.0, and gateway 192.168.1.1
Now Forward the ports you have to this static ip address, which you assign to your XBOX
Also make sure you are running latest firmware on your linksys router. You can check from www.linksys.com/download , If it is not latest, download and update to latest version.

Open NAT problems with Xbox One .

When I first got my 1900ac I used Media Priortization to get an open NAT for Call of Duty Advanced Warfare on my Xbox One ; prioritizing the Xbox . It worked fine for about 6 months until I changed cable/net provider to Nextech in Ks. This company uses the 1900ac to hook up it's system for all it's customers ( since I already had one they're using mine ). Unfortunately I'm unable to get an open NAT in this game anymore ; I've tried just about everything , NAT forwarding , triggering , Media Prioritization . Nextech support & Xbox Live support , useless . Tried Portforward . com , nothing . Forwarding port 53 cuts off net connection & doing the static ip change for Xbox didn't help . Almost everything I've looked at seems out of date & I'm at my wits end . It would seem by now Linksys should have solutions available , any ideas ?

Thank you chin_pamz13 for your response . I tried to check if my modem had a public or private ip address but I'm not sure how to do that ; I've read about double NAT's elsewhere . Regardless , I think I've finally found a solution that seems to be working so far . I went to the website " tech - recipes . com " & found an article , " Xbox One open NAT " by Aaron St. Clair . I tried his first suggestion about port triggering , with extra ports I had'nt seen before . That did not work for me so I followed his instructions for putting the Xbox in the DMZ & it's working ! I think my problems from before were the result of improperly setting up the static ip address for my router & Xbox . Previous instructions had me changing the ip in the console along with the router ; Aaron said not to do so in the Xbox , let the router do the work it's supposed to do & make sure the settings in the console are on automatic . In the router at the DMZ , I was'nt sure how to proceed , but at the bottom is a section labeled DHCP reservations list ; clicked on that , saw XboxOne , clicked on that & it filled out the MAC address above for me . Then I went to the Xbox network settings , advanced settings & clicked " automatic " at ip address , subnet & DNS . I checked mutiplayer connections & did the " hold bumper & trigger buttons " trick & finally got an open NAT ; fired up CoD Advanced Warfare & got the open NAT there also . I may have screwed up when I did the port triggering but since the DMZ fix seems to work I'm going to leave things alone . Hope this helps others with open NAT problems .

Problems with NAT and xbox live

i could once connect to xbox live using my westell 6100g which i received as an upgrade from the regular 6100 about 5 days ago. It worked fine yesterday and today it decided to change my NAT from "Open" to "Moderate".
how can i access my NAT so i can fix this frustrating problem? or how can i fix this ? I tried microsofts solutions including port forwarding but nothing works. my guess is my only option is to change the NAT but the interface of westell 6100's page is barely user friendly, and im a tech savvy guy. any help ?

Your other thread
http://www.dslreports.com/forum/remark,24291307
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

XBOX ONE. I have the xbox one and the airport time capsule and cant connect to most xbox live games and zero parties. I have 0 experience in all this but somehow was able to change NAT to open but still wont connect. HELLLPPPP

Okay folks, I need your help out there.
So the nerdy side of me went and picked up the XBOX ONE on release day. Its awesome by the way, BUT..... I cant seem to connect to most xbox live games and absolutely ZERO parties. At first I just thought it was something to do with the xbox itself and would eventually fix itself, but i was wrong. After looking into it on microsoft, i found out that it had to do with my NAT settings on the airport itself. I guess apple and xbox are not compatiable for xbox live and it makes it difficult to have an open NAT setting and is a huge PAIN.
I was able to pinpoint one that the airport time capsule was blocking the IPV6 something or another. Anyways, I unblocked that, and reset the modem and time capsule and jumped on the xbox and now have open NAT settings but still cant connect to multi-player.
Upon further searching, i was told to uncheck the UPNP on my time capsule as well, but have no idea how to find that.
I know it seems confusing, but thats the best i can describe it.
tthanks all

Be a long long time before I see an Xbox One.. but whoever told you to uncheck the upnp in the TC.. tell them their dreamin' .. upnp is not support by Apple in any computer or router, never has been.. Apple deliberately wrote their own version called NAT-PMP to do the same thing.. dynamically open ports at the request of an application or client computer.
So there is nothing like that to uncheck.. and as a matter of interest.. there no box to check or uncheck for NAT-PMP either.. since apple do not believe in end user adjustment of settings.. they simply do not exist.
You will have to manually forward all ports required by the Xbox via the TC. For multi-player games you probably need to open more ports than the standard to allow just xbox live. You will need to check the ports required and open them.
OR
Buy a standard vista UPNP compatible router.. and use that.. and simply put the TC in bridge in the network.
I have not seen posts yet about xbox one.. but there are plenty about xbox and ps3 and the fact that Apple really doesn't give a hoot about games consoles.
This is a good basic post for older xbox.
https://discussions.apple.com/thread/5385065?tstart=0

Cannot get Xbox Live to report NAT Open whatever i try.

Hi,
Ive read everything i can find on the internet about the latest Airport Extreme Base Station and Xbox Live and I cannot for the life of me manage to get the Xbox 360 to report "NAT - OPEN" during tests. Worst still it always comes back as NAT Strict.
I used to have an old Airport Extreme (the dome one) at my old place and the NAT was always Open on that and i dont even remember opening ports.
Ive checked all the threads and suggestions on this forum and nothing is working.
So far, i given my 360 a fixed IP both on the 360 itself, and then on the Airport Extreme by using the 360's wired MAC address. Ive checked that the IP is outside of the DCHP range which it is, and ive power cycled both devices many times and the 360 will always connect to the static IP ive set it up on - so that works.
Ive port forwarded all the ports Xbox Live needs (88 and 3074) and set them to its static IP - this didn't work.
Ive set the static IP of the Xbox 360 as DMZ (default host) and this didn't work either.
Ive power cycled my modem, my airport extreme and the 360 - this didn't work.
Ive unplugged everything from my Airport Extreme apart from the 360 - this didn't work.
I cannot see what else it could be, everytime I do the tests it reports back as strict.
My BeBox modem is definatly in bridge mode as all other port forwarding is working correctly for all software and hardware devices.
I personally cannot think of anything else as there really are not that many options to play with - and all ports are set to open for the 360 it should not be reporting as strict...
Can anyone help?

I might add - this is definately an Airport Extreme issue as i just plugged the 360 directly into the modem via Ethernet to get a direct connection and test and NAT was reported as OPEN.

WRT1900AC Problem With open NAT with multiple Xbox One's

I am starting a new thread for some possible help with this. I have just recently replaced my r7000 with the wrt1900ac router and for the life of me cannot get my 2 xbox ones in the house to have open nat. Only one of them will show open NAT. Anyone get this to work and work 100% of the time? I have reseverved the IP's. I tried port forwarding.. I tried putting one in the dmz. I have tried port triggering. None of it works. One will be open the other stays at moderate. I have got it in strict before as well. I have upnp on. I cannot figure out what is wrong with it. Ideas? Also It seems my router reboot on its own and turning the LED's off after a reboot the wireless led's come on. Seems like a bug.

Hewligun, found this on another Linksys thread, it appears that Linkysy may need to update their UPnP and all should be good. Original thread:Packet Dropping thread Excerpt from thread: Re: WRT1900AC packet dropping[ New ] Options ‎05-01-2014 06:16 PM I did some research. Microsoft documents that port forwarding will only work for the one xBox in the forwarding rule. In the same document it mentions that the only way to have two xBoxes running at the same location behind a router is with UPnP. The UPnP protocol has be the newest version in order for it to work. I guess the WRT1900AC is running a later version of UPnP in which case a firmware upgrade will solve this. Keep in mind that Microsoft xBox Live itself is having documented issues as well so we can't really know for sure if the UPnP on the WRT1900 is the newer version or not at this point. Look at the affect services in the current xBox Live status: Affected platforms:Xbox Onexbox one outage;Social and Gaming,Xbox 360xbox 360 outage;Social and Gaming, Affected services:Accessing all game featuresJoining other Xbox Live members in online gamesPosting game performance or viewing the performance of other Xbox Live members https://support.xbox.com/en-CA/xbox-live-status
Please remember to Kudo those that help you.
Belkin\Linksys
Communities Technical Support

Trying to change NAT connection from moderate NAT connection to an open NAT connection for XBOX LIVE

Hi, I have a Linksys Wireless-N Broadband Router/WRT160Nv2 and I have been trying to change my NAT connection from a moderate NAT connection to a open NAT connection for my Xbox Live on my Xbox 360. I can sign into my Xbox Live account but it is working on a moderate NAT connection. I have already enabled the UPnP and put in the proper port numbers. After doing that I signed into my Xbox Live on my Xbox 360 and tested my Xbox Live connection and still it says that I a moderate NAT connection. I do not know what elso to do and I would greatly appreciate step by step help from anybody who knows what they are doing. PLEASE HELP ME AS SOON AS POSSIBLE!!!!
Thank you

A known issue with Linksys routers is the NAT Type 3 or anything related to dropping of Internet connectivity during play time. Network Address Translation (NAT) is the ability of a router or firewall to translate a public IP address to a private IP address and vice versa. It adds security to the network by keeping the private IP addresses hidden from the outside world.
Here is the link, which will you in resolving the concern: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=2902de6218ed4dc1a4c595595ca1f60a_Resolving_NAT_Typ...

Open NAT xbox live problems

Similar Messages

Maybe you are looking for