OpenGL Enabled, but not working (Photoshop CS4)

I have having a weird problem with Photoshop CS4. First of all, let me give off the specs.
OS: Windows 7 64 bit
Graphics Card: AMD Radeon HD 7570 (Driver Version 8.960.11.1000, with latest Catalyst Control Center)
I use Photoshop CS4 for freelance work, and one of the tools I like to use is the Rotate tool. When I first got my desktop and installed Photoshop, everything worked fine. However, recently I was forced to perform and factory restore on my desktop thanks to a virus.
Today I started working on something and when I tried using the Rotate tool, it was not working (I go that error window saying it wasn't enabled). I checked the OpenGL settings to see it was enabled. Confused, I restarted Photoshop and tried again with no luck.
This turned into a search around the internet to see just what is going on, but the only thing I could find was suggesting updating drivers for my graphics card and Adobe, which I have tried with no success. I have found out that some people were having the same trouble as me, but what makes my case odd is that it was working fine before the factory restore.
Any help would be great.

Because of ATI's plethora of version information I'm not really sure what Catalyst release your 8.960.11.1000 driver comes from, but I do know that Catalyst 12.4 has some problems working with later versions of Photoshop. Perhaps Photoshop CS4 isn't too happy with it either.
The most recent Catalyst release that was known to be good with Photoshop was 12.2 (though it shows up as 12.3 in the status display). It can be found here:
http://support.amd.com/us/gpudownload/windows/previous/Pages/radeonaiw_vista64.aspx
Downgrading drivers is a bit more tricky than upgrading them - you have to fully remove the current ones first, then install the older set.
-Noel

Similar Messages

Camera Raw 5.1 downloaded and unzipped but not working in CS4. Can't open Nikon D90 NEF files.

Camera Raw 5.1 downloaded and unzipped but not working in CS4. OS Windows 7. Can't open Nikon NEF files. Camera Nikon D90.

update the adobe program that needs cr 4.6+, http://www.adobe.com/downloads/updates/

Back to my mac - iCloud enabled, but not working

Last year I made very regular use of Back to My Mac. Time and again I had no problems using my Mac Book Pro and connecting to my Mac Pro back home - did this from all over the place.
Then last month, my DSL router died and I had to upgrade.   The Netgear switch I had used stopped letting Back to My Mac work - turned out there was a glitch and I was one of the few who had a working unit, but not that it had tanked I could not get it back. All systems would get an error when trying to enable Back To My Mac instructing me to review my settings, enable UPnp, etc...
So now I have a new Netgear R6300 and my MiniMac, Mac Pro and Mac Book Pro all can have Back to My Mac checked without an error showing up. Can uncheck and re-check and the spinning wheel does it's thing and the box shows properly with no error.   Great - but apparently not really.   All these systems are in the same network, so of course they can see each other from within my network - no need for Back To My Mac at all.
But as soon as I try and connect from outside my network I can't.   The Netgear R6300 provides a guest wireless network (that can't see or share the home network), so I can grab another IP address and effectively be outside my home with the Mac Book Pro.   Again, no error when I look at iCloud - and I can uncheck and recheck the Back to My Mac box and the handshaking necessary seems to be fine - but I do not get my home systems appearing in the Finder Shared list as they once did.
The systems in my house can't see the Mac Book Pro either.
As I have a group of static IP addresses from Centurylink I can use a fireware adapter and directly connect a network cable to the M1000 DSL modem - and directly pull one of my other IP addresses for the Mac Book Pro and have it completely out from under the Netgear R6300.   But the situation is the same - the Mac Pro and Mini Mac both appear to be configuered for Back to My Mac (can check, un-check and recheck without an error), but they can't see the Mac Book Pro.   Likewise the Mac Book Pro appears properly set for Back To My Mac - but it can't see either the Mac Pro or the Mini Mac.
It makes no difference whether I enable the Centurylink M1000 DSL firewall or have it disabled.   UPnP is activated on the Netgear R6300, and if I turn it off I get an error when trying to set up Back to My Mac with any system funneling through the R6300 that the connection can't be made and I should check things like UPnP.    So when it is enabled there certainly seems to be at least some sort of semi proper handshaking going on.
For diagnostic purposes only, I have stretched a really long Cat 6 cable accross the room and plugged the Mac Pro directly into the M1000 DSL too - pulling yet another static IP from my assigned block. Now the Mac Book Pro and the Mac Pro can see each other via Back to My Mac - but neither can see the Mini Mac, and it of coruse can't see either of them.
I am not wedded to Netgear, but I have had lousy luck with Linksys and Asus - the Asus. The Mini Mac is a server (web and email) and Asus would not properly route mail to the Mini Mac and their Tech support was both difficult to reach and unable to explain why, just go try another.   The Linksis EA6500 was dead out of the box, and again Tech support suggested to just go get another one.   Asus was truly horrible to work with, but I would try another Linksis - but I have had flakey history with Belkin and Linksis which is why I went to Netgear.
So I know that the Centurylink M1000 does not appear to be the issue as devices connected directly to it can enjoy Back to My Mac.   I know that the Netgear R6300 appears to be working but clearly there must be something wrong somewhere.
I don't seem to be caught in a double NAT issue, and I don't have extreme firewall issues in play.   Much as I would like and intend to put stiffer rules in place, right now I just want to get thigns working.
Clearly I am missing something. Suggestions - even for a different router know to be working in a small but robust network with cable and wireless would be most welcome.   All three systems are running OS X 10.8.3 - the Mini Mac also running server. Both the Netgear R3600 and the Centurylink M1000 have the latest firmware.
Thanks in advance for your help.

Is the Extreme in bridge or router mode.. most people are finding it has to be in router mode to work although I don't think that is specific in the instructions..
You should not need to access the extreme to get into the Mac though.. do you have a hard disk on the AE you are trying to access??

Touch Pad is enabled but not working

I have just this minuet reinstalled Win XP and the touch pad is not working and I cant work out what is coursing this problem....
The Toshiba console is saying that it is enabled but it is not working? Help!
p.s.
I bought 512 MB of RAM for and I cant get it to go in..
Any help would be grateful.
Thanks dazmo b

On this way I can just tell you to check touchpad settings and FN+F9 key combination.
About memory upgrade I can not tell you much because i dont know which notebook model you have.
Bye

My wake on lan is enabled but not working

I have a mid June '12 Macbook Pro running splashtop. I have enabled wake on LAN through "Energy Saver" under "Preferences." The Macbook Pro is hooked up to an ethernet cable to my AirPort Extreme router. When I try to use "Wake on LAN" button/icon/feature through Splashtop 2 on my iPad, my Macbook Pro remains shutdown or in standby mode. Also, I have an SSD installed with 8GB of RAM if this matters any. Is anyone having this problem and can someone offer some advice? Thank you.

is the macbook pro closed or open? it can't wake if its closed despite your 'wake on lan' setting
if that's not the case, try
http://apple.stackexchange.com/questions/14680/why-is-wake-on-lan-not-working-on -my-macbook-pro-with-logmein

OpenGL enabled but not recognized in CC2014 in Windows 8

When I try to open a 3D file in CC2014, I receive an error message which states "Could not complete your request because 3D functionality is currently disabled due to OpenGL being disabled". Yet, when I go under "Help-System Info" is shows OpenGL IS enabled. Operating system is Windows 8. Any ideas? Thanks!

Well, the drivers at the computer manufacturer's site are many times outdated. What brand is the graphics processor?
Upgrading Display Drivers in Windows: Click on the Start menu, and select Run. In the Open box, type "dxdiag" (without the quotation marks), and then click OK. The DirectX Diagnostic Tool opens. Click the Display tab. On the Display tab, information about your graphics card is shown in the Device section. You can see the name of your card, as well as how much video memory it has. Once you know the kind of graphics card you have, visit the manufacturer's website to download the latest driver. Here are links for downloading drivers from the most common graphics card manufacturers:
NVIDIA: Drivers - Download NVIDIA Drivers
AMD: Download Drivers
Intel: Support for Graphics Drivers
Also, under Help>System Info, how much vRAM does the GPU have? You'll need at least 512 MB to run 3D in Photoshop CC 2014
Benjamin

Hardware virtualization enabled but not working in HP Pavilion p6

I've got an HP Pavilion p6 series (Model no. p6-2003es), with an up-to-date v7.15 BIOS, and I'm unable to use hardware virtualization.
I've enabled Virtualization in the BIOS under System Security, pressed F10 and saved the changes as per the usual procedure when modifying BIOS settings. However, when trying to run virtualization software (Virtualbox in this case), I get a warning notice stating that processor supports virtualization, but it's not enabled.
This seems to be the case: the feature is supported, but the BIOS does not seem to change the setting and enable it. I've tested it under 2 different OSs, with the same result:
Under the original Windows 7 64-bit, I've ran the Microsoft HAV Detection Tool, which tells me that hardware virtualization is not enabled.
Under Ubuntu 12.04, I've ran the rdmsr tool, which allowed me to read the AMD MSR (Model Specific Register) bits concerned with virtualization, and confirmed that they are not enabled.
I suspect that this is a BIOS issue (i.e. it's not setting the bits required to enable virtualization), but after a search on the forums it strikes me that no one has reported it yet, so any help, comments or workaround for this issue will be really welcome.
Thanks!

Hi MattNC79,
If you search this forum for the following tags you might find a solution as there are many for virtualization issues.
VT, VTx, VTd, Hyper-v, virtualization
HP internal has indicated the virtualization is not supported consumer level PC. It's up to the individual to make it work, if it is possible, with perhaps the volunteers on this forum as HP has no official presence on this forum.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Flashplayer 11 installed and enabled but not working

using IE 11 with Windows 7. previous version(s) have worked in the past. However IE version 11 was recently installed and flash player issue started at that time. Maybe related??? Adobe site says installation successful. Went through all related troubleshooting tips and no issues were found.

IE11 has wrought havoc since it was released.
Facebook, Yahoo, YouTube, Pogo... all have reported numerous problems.
Microsoft has recommended enabling Compatibility view for affected sites: http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11 but that has met with about 50% success.

Script that worked in CS does not work in CS4 - multiple open page, print , pdf export and close

I had a script that worked great for me in Indesign CS. But now does not work in CS4. Anyone knows what needs to be done to make it work again ?
When I drop folder with indesign files on top of this script:
1. opens first page
2. turns specific layer on
3. prints using preset
4. exports using preset
5. close without saving
6. next page
Anyone who can give me solution or idea how this should work is greatly appreciated.
on open sourceFolders
repeat with sourceFolder in sourceFolders
tell application "Finder"
try
-- If you would like to include subfolders, you say - every file of entire contents of folder…
set idFiles to (every file of folder sourceFolder whose file type is "IDd5") as alias list
on error -- work around bug if there is only one file
set idFiles to (every file of folder sourceFolder whose file type is "IDd5") as alias as list
end try
end tell
if idFiles is not {} then
tell application "Adobe InDesign CS4"
set user interaction level to never interact
repeat with i from 1 to count of idFiles
open item i of idFiles
tell document 1
try
set visible of layer "ImagesTag_Layer" to true
end try
set myPreset to "letter size" -- name of print style to use
with timeout of 700 seconds
print using myPreset without print dialog
end timeout
set myPreset1 to "pdf preset name" -- name of pdf export style to use
set myName to the name -- name includes .indd should remove at some point
with timeout of 700 seconds
export format PDF type to "users:temp:Desktop:pdf:" & myName & ".pdf" using myPreset1 without showing options -- set path here format ComputerName:Folder1:Folder2:......:FileName.pdf
end timeout
close without saving
end tell
end repeat
set user interaction level to interact with all
end tell
end if
return 10 -- try again in 10 seconds
end repeat
end open

(Disclaimer: me not an AS guy!)
First thing I noticed is the interaction level is set off. If you comment out this line
set user interaction level to never interact
you might be able to pinpoint the exact error -- ID will display a standard "failed" dialog, hopefully showing the line that it fails on.
A quick question: the script assumes two presets in your InDesign: one for print ("letter size") and one for PDFs ("pdf preset name"):
set myPreset to "letter size" -- name of print style to use
set myPreset1 to "pdf preset name" -- name of pdf export style to use
Do these actually exist in your CS4, with the same (non)capitalization and spaces?

Page is working ok in chrome and IE but not working in firefox. jquery problem i guess

http://184.170.251.149/raschet-shkafa-kupe
this page is working correctly in chrome and IE but not working in firefox, i cant click and of the dropdown menus(ДСП, доличество дверей). it was working perfectly prior firefox 18. can you please fix the compatibility problem ?

I was referring to the second page in my above post.
I disabled JavaScript as a test after loading the page with JavaScript enabled and that worked.<br />
I also get the selects to open if I right-click instead of left-click the select.<br />
That way the select get selected (shows a focus ring) and after that left-clicking works as well .
This assumes that JavaScript is monitoring the left-click, but that script no longer works properly.
A good place to ask advice about web development is at the MozillaZine "Web Development/Standards Evangelism" forum.
*http://forums.mozillazine.org/viewforum.php?f=25
The helpers at that forum are more knowledgeable about web development issues.<br>
You need to register at the MozillaZine forum site in order to post at that forum.

Isdn bchan-number-order ascending round-robin is applied but not working

isdn bchan-number-order ascending round-robin is applied but not working
ios c3825-spservicesk9-mz.124-21.bin
relevant config
controller E1 0/3/0
framing NO-CRC4
pri-group timeslots 1-31
interface Serial0/3/0:15
no ip address
encapsulation hdlc
no logging event link-status
no snmp trap link-status
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
isdn bchan-number-order ascending round-robin
trunk-group 1
no cdp enable
my problem is this:-
At the moment calls are leaving on the first available channel of my h323 voice gateway PRI, I can apply this command to the interface fine but it makes no difference the b cannels are always being picked on a first come first served basis . I have also tried combination "isdn bchan-number-order decending" and "isdn bchan-number-order descending round-robin" but it makes no difference , the first b channel is always selected .
Any ideas , if you think its a bug can u identify the bug id as I cannot find it .

Hello
I can see that you use ascending , that why you hit 1st channel.You have to choose one of these commands ascending or descending
I have a question here , for your incoming calls which channel hits ?.FYI isdn bchan-number-order descending is enable by default , so if you need to change you have to type ascending. Can you just share incoming calls which channel hits?.This is because before you define your outgoing calls , you have to check your service provider channel used, and this to avoid error channel is not available.
Command
Router(config-if)# isdn bchan-number-order {ascending | descending}
Purpose
Enables B channel selection for outgoing calls on a PRI interface (optional).
Thanks
please rate all useful information

Set Stroke weight for a frame not working in CS4.

Hi All,
How to set Stroke weight for a frame.
I tried using CreateStrokeWeightCommand of IGraphicAttributeUtils, but its not working in CS4.
Regards,
Jasmine
Message was edited by: Jasmine_Shaikh

Hi All,
CreateStrokeWeightCommand of IGraphicAttributeUtils works only when if the frame has some stroke weight already applied to it.
So do i need to set something else before using CreateStrokeWeightCommand to make it work programatically on a frame with no stroke weight.
Jasmine

Curves Not Working in CS4

I have installed CS5 but still work in CS4, too, because Adobe hasn't developed the CS5 plug-in that I use for my printer.
Since I've installed CS5, I cannot get the Curves function to work in CS4.
When I add a Curve layer, the layer appears, but the Adjustment window doesn't open. When I select the Adjustment
layer in the menu, a blue line temporarily glows around my Layers window, but it never opens.
Any clues?
avebon

avebon wrote:
…When I add a Curve layer, the layer appears, but the Adjustment window doesn't open.
Are you aware of the new Adjustments Panel?
Command-Click on thumbnail to see full-size image in new tab (Firefox)
The old modal Curves dialog box has been eliminated in CS4.
There was an optional Curves Dialog you could add to get the old modal Curves dialog. I don't know if it's still being offered:
http://blogs.adobe.com/jnack/2008/11/configurator_is_live.html
Scroll down to a paragraph that reads:
During the Photoshop prerelease cycle, some customers complained about losing the ability to create & edit a curves adjustment layer via a dialog, instead of via the new Adjustments panel. To ease their transition I made a simple panel (screenshot) that lets you create & edit curves layers via a dialog.
Wo Tai Lao Le
我太老了

DragAcceptFiles Working in Windows 10 TP build 9926 But Not Working In build 10049 and build 10061

This is a cross post from
https://social.technet.microsoft.com/Forums/en-US/a63519d4-ba7a-46c1-bb34-ad034b836964/dragacceptfiles-working-in-9926-but-not-working-in-10049-and-10061?forum=WinPreview2014General. The moderator suggested I post this here:
My company has a software product that accepts dragged items. In all versions of Windows from XP through Windows 10 build 9926 that functionality has worked fine. However, with build 10049 (possibly 10041 which I did not test thoroughly before going
to 10049) and now 10061 that functionality stopped working. The application calls DragAcceptFiles to enable drag drop messages. In addition, either ChangeWindowMessageFilter is called on Vista or ChangeWindowMessageFilterEx is called on Windows
7 and higher for the messages WM_DROPFILES, WM_COPYDATA, and WM_COPYGLOBALDATA. This was working fine on Windows 10 build 9926. Now when I attempt to drag an item to our software product, I get the "Don't" symbol (circle with line through
it) and no WM_DROPFILES messages are received. The application is unchanged with only an upgrade to the Windows 10 build performed. As a sanity check, I created a brand new VM running build 9926 and the functionality worked fine. I then upgraded
the VM to 10049 and it stopped working. The following day I upgraded to 10061 and it is still broken. Is there are new filter or restriction in place since build 9926 on DragAcceptFiles that would be stopping the traditional drag drop procedure
from working? This is very frustrating because there is a dearth of information on Windows 10 API changes and since this appears to be some kind of recent change, I am out of ideas of where to look for answers. I can duplicate this problem on the older
platforms by simply calling DragAcceptFiles with the second parameter set to false. In that case, on Windows 7 for example, I will get the "Don't" symbol just I am getting now in the Windows 10 TP with the argument set to true.

DragAcceptFiles is now working again in 10074 so whatever the problem was, it has been fixed.

10.3.183.5 downloaded but not working, Explorer 9

Downloaded successfully on Windows 7 computer with Explorer 9 (32 & 64 bit), but not working - can not view youtube, etc.

The current release version (10.3.183.5) will not work on 64-browsers; you can only use it with the 32-bit version of Internet Explorer.
On IE9, Tools, Add-ons, can you see Shockwave Flash Object, and is it enabled? (It must be enabled.)
On IE9, Tools, do you have ActiveX Filering enabled? (It must be disabled, either globally, or individaully for websites with Flash content.)
For more information on ActiveX Fitlering see http://forums.adobe.com/thread/867968

OpenGL Enabled, but not working (Photoshop CS4)

Similar Messages

Maybe you are looking for