Operational Quorum and both nodes rebooting.

I've experienced an issue that when I rip out the SCSI cables to shared storage (and the quorum device), both nodes panic and
reboot. Is this expected behavior?
It seems that it is understandable that the active node reboots, because it lost the disk-path and quorum device. But should
the stand-by node reboot to?

No problem.
It's running S10 update 4 w/ SC 3.2.
3120 JBOD attached to two T2000's, two-node cluster.
I'm wondering if the stand-by node didn't see the quorum device, when the the active nodes scsi cables were pulled.
We pulled the standby nodes SCSI cables and reconnected them prior to pulling the active nodes. The difference was that the stand-by node's /var/adm/messages log was filled with expected messages regarding a missing disk. The cables were re-attached to the stand-by and then yanked out of the active node. This is when both nodes panicked.

Similar Messages

Both cluster node reboot

There is a two nodes cluster and running Oracle RAC DB. Yesterday both nodes rebooted at the same time (less than few seconds different). Don't know it was caused by Oracle CRS and server itsefl?
Here is the log:
/var/log/messages in node 1
Dec 8 15:14:38 dc01locs01 kernel: 493 http://RAIDarray.mppdcsgswsst6140:1:0:2 Cmnd failed-retry the same path. vcmnd SN 18469446 pdev H3:C0:T0:L2 0x02/0x04/0x01 0x08000002 mpp_status:1
Dec 8 15:14:38 dc01locs01 kernel: 493 http://RAIDarray.mppdcsgswsst6140:1:0:2 Cmnd failed-retry the same path. vcmnd SN 18469448 pdev H3:C0:T0:L2 0x02/0x04/0x01 0x08000002 mpp_status:1
Dec 8 15:17:20 dc01locs01 syslogd 1.4.1: restart.
Dec 8 15:17:20 dc01locs01 kernel: klogd 1.4.1, log source = /proc/kmsg started.
Dec 8 15:17:20 dc01locs01 kernel: Linux version 2.6.18-128.7.1.0.1.el5 ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44)) #1 SMP Mon Aug 24 14:07:09 EDT 2009
Dec 8 15:17:20 dc01locs01 kernel: Command line: ro root=/dev/vg00/root rhgb quiet crashkernel=128M@16M
Dec 8 15:17:20 dc01locs01 kernel: BIOS-provided physical RAM map:
ocssd.log in node 1
CSSD2009-12-08 15:14:33.467 1134680384 >TRACE: clssgmDispatchCMXMSG: msg type(13) src(2) dest(1) size(123) tag(00000000) incarnation(148585637)
CSSD2009-12-08 15:14:33.468 1134680384 >TRACE: clssgmHandleDataInvalid: grock HB+ASM, member 2 node 2, birth 1
CSSD2009-12-08 15:19:00.217 >USER: Copyright 2009, Oracle version 11.1.0.7.0
CSSD2009-12-08 15:19:00.217 >USER: CSS daemon log for node dc01locs01, number 1, in cluster ocsprodrac
clsdmtListening to (ADDRESS=(PROTOCOL=ipc)(KEY=dc01locs01DBG_CSSD))
CSSD2009-12-08 15:19:00.235 1995774848 >TRACE: clssscmain: Cluster GUID is 79db6803afc7df32ffd952110f22702c
CSSD2009-12-08 15:19:00.239 1995774848 >TRACE: clssscmain: local-only set to false
/var/log/messages in node 2
Dec 8 15:14:38 dc01locs02 kernel: 493 http://RAIDarray.mppdcsgswsst6140:1:0:2 Cmnd failed-retry the same path. vcmnd SN 18561465 pdev H3:C0:T0:L2 0x02/0x04/0x01 0x08000002 mpp_status:1
Dec 8 15:14:38 dc01locs02 kernel: 493 http://RAIDarray.mppdcsgswsst6140:1:0:2 Cmnd failed-retry the same path. vcmnd SN 18561463 pdev H3:C0:T0:L2 0x02/0x04/0x01 0x08000002 mpp_status:1
Dec 8 15:17:14 dc01locs02 syslogd 1.4.1: restart.
Dec 8 15:17:14 dc01locs02 kernel: klogd 1.4.1, log source = /proc/kmsg started.
Dec 8 15:17:14 dc01locs02 kernel: Linux version 2.6.18-128.7.1.0.1.el5 ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44)) #1 SMP Mon Aug 24 14:07:09 EDT 2009
Dec 8 15:17:14 dc01locs02 kernel: Command line: ro root=/dev/vg00/root rhgb quiet crashkernel=128M@16M
Dec 8 15:17:14 dc01locs02 kernel: BIOS-provided physical RAM map:
ocssd.log in node 2
CSSD2009-12-08 15:14:35.450 1264081216 >TRACE: clssgmExecuteClientRequest: Received data update request from client (0x2aaaac065a00), type 1
CSSD2009-12-08 15:14:36.909 1127713088 >TRACE: clssgmDispatchCMXMSG: msg type(13) src(1) dest(1) size(123) tag(00000000) incarnation(148585637)
CSSD2009-12-08 15:14:36.909 1127713088 >TRACE: clssgmHandleDataInvalid: grock HB+ASM, member 1 node 1, birth 0
CSSD2009-12-08 15:18:55.047 >USER: Copyright 2009, Oracle version 11.1.0.7.0
clsdmtListening to (ADDRESS=(PROTOCOL=ipc)(KEY=dc01locs02DBG_CSSD))
CSSD2009-12-08 15:18:55.047 >USER: CSS daemon log for node dc01locs02, number 2, in cluster ocsprodrac
CSSD2009-12-08 15:18:55.071 3628915584 >TRACE: clssscmain: Cluster GUID is 79db6803afc7df32ffd952110f22702c
CSSD2009-12-08 15:18:55.077 3628915584 >TRACE: clssscmain: local-only set to false

Hi!
I suppose this seems easy: you have a service at 'http://RAIDarray.mppdcsgswsst6140:1:0:2' (a RAID perhaps?) which failed. Logically all servers connected to thi RAID went down at the same time.
Seems no Oracle problem. Good luck!

Cluster doesn't have operational quorum - one node of the cl couldnt reach

Hi All,
(I posted this issue at an other forum but I thought this one is more suitable, sorry to post it again)
I'd like to ask help regarding to the problem I had which made me
block. Unfortunately my investigation was not good enough.
Here is the brief description below;
I have a V440 cluster and one of the node could not boot up
successfully, startup log says me;
cluster doesn't have operational quorum yet; waiting for quorum.
what I did were;
1./ booting both nodes at the same time - didn't work
2./ shutdown good node and only started up bad node - didn't work
3./ replaced cluster interconnect cables with working cables - didn't
work
Please take a look at the startup log and let me know what I should do
further.
Your helps will be really appreciated for me thx,
++++++++++
Rebooting with command: boot
Boot device: disk0 File and args:
SunOS Release 5.9 Version Generic_122300-28 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
/pci@1d,700000/pci@1/scsi@4 (qus0):
initiator SCSI ID now 6
/pci@1d,700000/pci@1/scsi@5 (qus1):
initiator SCSI ID now 6
/pci@1d,700000/pci@2/scsi@4 (qus2):
initiator SCSI ID now 6
/pci@1d,700000/pci@2/scsi@5 (qus3):
initiator SCSI ID now 6
Hardware watchdog enabled
SC unretrieved msg SEP 16 09:21:50 2008 UTC [Host System has Reset]
Starting VxVM restore daemon...
VxVM starting in boot mode...
NOTICE: vxvm:vxdmp: added disk array OTHER_DISKS, datype = OTHER_DISKS
NOTICE: vxvm:vxdmp: disabled path 32/0x298 belonging to the dmpnode
232/0x8
NOTICE: vxvm:vxdmp: disabled dmpnode 232/0x8
configuring IPv4 interfaces: ce1 ce2 ce5 ce6.
Hostname: kadikoy
VxVM starting special volumes ( swapvol rootvol var oracle
rootdisk_25vol )...
Booting as part of a cluster
NOTICE: CMM: Node taksim (nodeid = 1) with votecount = 1 added.
NOTICE: CMM: Node kadikoy (nodeid = 2) with votecount = 1 added.
NOTICE: CMM: Quorum device 1 (/dev/did/rdsk/d4s2) added; votecount =
1, bitmask of nodes with configured paths = 0x3.
NOTICE: clcomm: Adapter ce8 constructed
NOTICE: clcomm: Path kadikoy:ce8 - taksim:ce8 being constructed
NOTICE: clcomm: Adapter ce4 constructed
NOTICE: clcomm: Path kadikoy:ce4 - taksim:ce4 being constructed
NOTICE: CMM: Node kadikoy: attempting to join cluster.
NOTICE: clcomm: Path kadikoy:ce8 - taksim:ce8 errors during initiation
NOTICE: clcomm: Path kadikoy:ce4 - taksim:ce4 errors during initiation
WARNING: Path kadikoy:ce8 - taksim:ce8 initiation encountered errors,
errno = 62. Remote node may be down or unreachable through this path.
WARNING: Path kadikoy:ce4 - taksim:ce4 initiation encountered errors,
errno = 62. Remote node may be down or unreachable through this path.
NOTICE: CMM: Quorum device 1 (gdevname /dev/did/rdsk/d4s2) can not be
acquired by the current cluster members. This quorum device is held by
node 1.
NOTICE: CMM: Cluster doesn't have operational quorum yet; waiting for
quorum.
NOTICE: vxvm:vxdmp: enabled path 32/0x298 belonging to the dmpnode
232/0x8
NOTICE: vxvm:vxdmp: enabled dmpnode 232/0x8
++++++++++

Tim.Read wrote:
The key messages are:
NOTICE: clcomm: Path kadikoy:ce8 - taksim:ce8 errors during initiation
NOTICE: clcomm: Path kadikoy:ce4 - taksim:ce4 errors during initiation
WARNING: Path kadikoy:ce8 - taksim:ce8 initiation encountered errors,
errno = 62. Remote node may be down or unreachable through this path.
WARNING: Path kadikoy:ce4 - taksim:ce4 initiation encountered errors,
So the heartbeat networks between the two machines aren't working. Without that, the existing node won't allow this node to join the cluster and then release its reservations.
Regards,
Tim
---hi,
thanks,
but interconnects are connected point-to-point and working fine on other clusters, so How can I investigate heartbeat networks?
on the other side as you said bad node can not boot up.
regards,
Halit

I have Adobe Acrobat 9 Standard on both of my computers. Some time ago, one crashed my computer and I had to reinstall the operating system and all applications. After I had installed once Acrobat 9 Sdt in the computer, I wanted to update the software v

I have Adobe Acrobat 9 Standard on both of my computers.
Some time ago, one crashed my computer and I had to reinstall the operating system and all applications.
After I had installed once Acrobat 9 Sdt in the computer, I wanted to update the software version 9.0.0 update to the same level as it was before the crash and that the other computer has version named 9.5.5.
The system for update from version 9.0.0 does not work at all. "There are no updates" listed in the dialog.
Can you advise how I get my Adobo Acrobat 9 Standard (Version 9.0.0) could be updated to the same level as the computer had before the crash.

ftp://ftp.adobe.com/pub/adobe/acrobat/win/9.x/

I am having trouble updating the operating system on both my ipad and iphone. I get a strange message when I open my PC desk top that says "the procedure entry point sqlit3_wal-checkpoint could not be located in teh dynamic link library SQLite3.dll"

I am having trouble updating my operatI am having trouble updating the operating system on both my ipad and iphone. I get a strange message when I open my PC desk top that says "the procedure entry point sqlit3_wal-checkpoint could not be located in the dynamic link library SQLite3.dll" Any ideas what my problem is?

Hi whatsthe77,
Welcome to Apple Support Communities.
You may want to follow the steps in this article to reinstall iTunes:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
http://support.apple.com/kb/HT1923
Have a great day,
Jeremy

Operating OS X on MacBook use a wired 4G hotspot and both Chrome and Safari are running sluggish, freezing machine, and even pop-ups ask to Kill or Wait. i wait. Have tried the Utility Permission Verified and Permission Repair and actually got worse. ??

operating OS X on MacBook use a wired 4G hotspot and both Chrome and Safari are running sluggish, freezing machine, and even pop-ups ask to Kill or Wait. i wait. Have tried the Utility Permission Verified and Permission Repair and actually got worse. ??
If I install OS X Maverick with its fixes will this fix the problem??
HELP

Mac OS X ver 10.6.8 Processor 2 GHz Intel Core 2 Duo , Memory 2 FB 1067 MHz DDR3, Startup Disc OS X HDD , No DVD available, Not removing Chrome - run entire business on 5 gmail accounts and operations.
L2 Cache:          3 MB
Memory:          2 GB
Bus Speed:          1.07 GHz
Boot ROM Version:          MB51.007D.B03
FUJITSU MHZ2160BH FFS G1:
Capacity:          160.04 GB (160,041,885,696 bytes)
Model:          FUJITSU MHZ2160BH FFS G1
Revision:          0081008C
Serial Number:                  K64JT8928554
Native Command Queuing:          Yes
Queue Depth:          32
Removable Media:          No
Detachable Drive:          No
BSD Name:          disk0
Medium Type:          Rotational
Partition Map Type:          GPT (GUID Partition Table)
S.M.A.R.T. status:          Verified
Volumes:
Capacity:          209.7 MB (209,715,200 bytes)
Writable:          Yes
BSD Name:          disk0s1
OS X HDD:
Capacity:          125.63 GB (125,627,793,408 bytes)
Available:          55.99 GB (55,987,331,072 bytes)
Writable:          Yes
File System:          Journaled HFS+
BSD Name:          disk0s2
Mount Point:          /
BOOTCAMP:
Capacity:          34.07 GB (34,068,234,240 bytes)
Available:          6.58 GB (6,580,842,496 bytes)
Writable:          No
File System:          NTFS
BSD Name:          disk0s3
Mount Point:          /Volumes/BOOTCAMP
This is a friends computer and I do not have access to apple codes, or how this system works.

My apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to.. Help

my apple tv was working fine untill the AirPlay option disappeared. I haven alterd the settings and have tryed rebooting both iPhone and ipad. I even rebooted the ATV and that disn't work. i am connected to the same network on both devices to. My iPad is up to date but my phone isn't but as I said mirroring and AirPlay worked fine on both devices befor...

Hi F1N5G10,
Thanks for contributing to the Apple Support Communities.
It sounds like you don't have the AirPlay option on your iOS devices. Restarting your Apple TV and iOS devices was a good first step, and you can find some additional tips to guide your troubleshooting at this link:
Resolve issues with AirPlay and AirPlay Mirroring from iPhone, iPad, and iPod touch - Apple Support
Sincerely,
Jeremy

I've just moved from PC to Mac, with my PC i and using Vmware Player I used to work on 2 Virtual M/C both on 2 external drives, one Windows Server 2000 as operating system and the sec. WindowsXP, is their a way to open these m/c on my mac

I've just moved from PC to Mac, with my PC i and using Vmware Player I used to work on 2 Virtual M/C both on 2 external drives, one Windows Server 2000 as operating system and the sec. WindowsXP, is their a way to open these m/c on my mac

I am so glad to hear about your success. As you are new to the Mac environment, I will be glad to help you more.
You said: "I can't change the setup yet but i have access". I don't understand what you mean about changing the setup! Please let me know more about that.
I also recommend to use Boot Camp, which allows you to install windows on a partition of your internal hard drive. This has many benefits. First, you can restart your computer and start up in windows. This makes your Mac device a complete windows machine and you gain the most from your hardware when working in Windows. Second, if a problem occures to your Mac OS X, you can restart your machine in Windows and prevent your data from getting lost. Third, you can import the Windows installed on the boot camp partition in to the Mac OS X using VMWare Fusion and work with it as a virtual machine. In this situation, VMWare enables you to work directly with your Windows in the boot camp partition. So it does not create a file package for the virtual machine in OS X.
Regarding the data safety and reliablity, I strongly recommend using Time Machine. You can also set it up to back up your virtual machines or not. This is possible to set up in the Virtual Machine Preferences Page in VMWare Fusion, or in the Time Machine preferences page in the System Preferences app of OS X.
Please don't hesitate to ask any other question. I will be glad to help you.

Whenever i try to manually sync my iPhone with a new playlist on iTunes (on my laptop), it always gets stuck in step 7, Waiting for changes to be applied, and then nothing happens. I'm running the latest operating systems on both my iPhone 5 and macbook

Whenever i try to manually sync my iPhone with a new playlist on iTunes (on my laptop), it always gets stuck in step 7, Waiting for changes to be applied, and then nothing happens. I'm running the latest operating systems on both my iPhone 5 and macbook

I really don't appreciate the fact that no one from Apple seems to be dealing with the many, many threads that have started on this topic since iOS 7 came out. In any event, I seem to have solved my problem with a full software restoration -- that is, iOS software restoration.
I clicked on "Restore iPhone..." which does a complete reinstall of the iOS but also all apps, photos, songs, etc. Took about 45 minutes, but seems to have worked.
I had previously tried reverting to a backup of my iPhone, but that did not solve the problem. Only a full restore solved it.

Premiere CS5 - Project Monitor playback is jerky after resintall of operating system and CS5

PROBLEM: Premiere CS5 - Project Monitor playback is jerky
This had NOT been an issue prior to reinstalling the operating system and all software. I have read numerous articles on the forums and have tried everything I can find...with no results.
STEPS TAKEN TO RESOLVE THE PROBLEM:
I have scoured the articles here http://www.adobe.com/cfusion/search/index.cfm?loc=en_us&term=choppy%20video&cat=support&pr oduct=premierepro and others at Cretive Cow
I have installed all updates for CS5 Master Collection, immediately following a fresh install of the operating system and SC5 Master Collection.
I have ensured that sequence settings match resolution and frame rates of footage - the problem persists.
I have tested by importing both standard def AVI files created from tape and high def SONY MP4 files - the problem persists.
I have ensured the latest Video drivers are installed (clean installation selected, so that the Windows default would be removed) - the problem persists.
I have tried the 3D settings in NVIDIA control panel | Program Settings tab... selected Adobe Premiere Pro from the drop down menu | and chaged 'Multi-display/mixed-GPU acceleration from the value of 'Multiple Display performance' to the value of 'single display performance'; although, I ran two monitors before using this latest NVIDIA video driver and I didn't experience this jerky footage issue - the problem persisted after affecting that change; so, I switched it back.
Since I have 96 GB of RAM, I don't use a pagefile. A zero MB page file is the same setting I had prior to rebuilding the C: Regardless of whether I have a pagefile or not, the problem persists.
I have tried creating a fresh user profile, where the user profile is created on the C: drive by default; and, where I left it there on C: to test for the jerky playback in a new PrPR project - the problem persists.
Regarding the C: (system drive) and why I reinstalled everything, it had become unstable and was locking up. I ran DISK ERROR CHECKING with the FIX parameter and the system was still locking up on me. Keep in mind that the System drive is a solid state drive. Anyhow, I had no choice but to dive in and reinstall everything. I wiped the system partition of the SSD using quick format and started installing the operating system. Now, I've read the CLAIM that this cuases performance issues; but, the only place I see issues is in the video monitor playback in PrPr. Everything else - Office applications...printing...browsing the Internet...works just fine, everything is responsive, whereas, I couldn't do ANYTHING with it before.
SYSTEM CONFIGURATION:
The Operating system and all software is installed on C:
All data files and most profile related folders are stored on D:
C:\ (one Intel Solid State Drive - SYSTEM DRIVE) Used Space: 57.5 GB Free Space: 388 GB
D:\ (four Western Digital 2TB drives in an on-board INTEL hardware RAID5 array & hotswapable backplane) used space: 1.28 TB Free space: 4.16TB
Adobe Premiere Pro CS5 VERSION: 5.0.3 (005 (MC: 218798))
Operating System    Microsoft Windows 7 Ultimate Version    6.1.7601 Service Pack 1 Build 7601
System Manufacturer    Intel Corporation
System Model    S5520SC
System Type    x64-based PC
Video    NVIDIA Quadro FX 4800 driver v.320.78
Display        Dell 27" LCD (DisplayPort)
Display        Dell 27" LCD (DisplayPort)
Processor    Intel(R) Xeon(R) CPU           X5680 @ 3.33GHz, 3326 Mhz, 6 Core(s), 12 Logical Processor(s)
Processor    Intel(R) Xeon(R) CPU           X5680 @ 3.33GHz, 3326 Mhz, 6 Core(s), 12 Logical Processor(s)
Installed Physical Memory (RAM)    96.0 GB
Page File Space    0 bytes
PREMIERE PRO CS5 SETTINGS:
Monitor PLAYBACK RESOLUTION: Full
Monitor PAUSE RESOLUTION: Full
(regardless of this setting, the problem persists)
PREFERENCES:
MEMORY:
Installed RAM: 95.9 GB
RAM reserved for other applications: 10 GB
Optimize rendering for: Performance
(Changing this setting to 'memory' does not resolve the problem)
MEDIA:
Media Cache Files
X - Save Media Cached files next to originals when possible
LOCATION: D:\Users...\AppData\Roaming\Adobe\Common
(User Profile folders were relocated to D:\ from within the properties of each folder's 'LOCATION' tab. This is the same configureation I had prior to rebuilding the C:\drive. Testing under a new profile where it's allowed to stay on teh system drive does NOT resolve the problem.)
Media Cache Database
LOCATION: D:\Users...\AppData\Roaming\Adobe\Common
PROJECT SETTINGS:
Scratch Disks
Path: D:\Users...\My Documents\
General
Video Rendering and Playback: Mercury Playback Engine GPU Acceleration
(Setting Viideo Rendering and Playback to 'Sofware' does not resolve the problem)
If any of y'all have any other suggestions, I'm all ears.
Thank you.

I'VE RESOLVED THE PROBLEM!
PREFACE:
OK, I am hoping that through this week-long Operating-System-and-Software-reinatalltion excerise of mine, I have revealed something that everyone -- whom have been cursing Adobe over -- can apply to their systems to resolve this jerky video problem within PremierePro CS5 (and quite possibly other versions, too).
If you've read my post above, you've seen all the steps I've taken to resolve the problem. I've read many posts, some of which have mentioned hardware upgrade / opitmization steps that one may take to enhance performance, and hopefully resolve the problem. I've read where people have taken these steps and have still experienced the problem...and then they curse Adobe. Fer-shame, fer-shame, fer-shame! (nod to Gomer Pyle).
In my case, I knew it wasn't an Adobe issue, as it had worked flawlessly before; and, it wouldn't require a hardware upgrade or reconfigureation, as my system is completely maxed out with two processors, a system drive and a hardware RAID5 array, a CUDA-suported nVIDIA 4800 FX card, and 96 GB of RAM. bla bla bla, puke...whatever. Bottom line is this:
It's not a software issue. It's not and Adobe issue; and Gawd no! It's NOT a PC vs. Mac issue! HA HA. The software had worked swimmingly well prior to the reinstallation / 'lobotomy' I perfomed on the system drive.
SOLUTION FOR ME:
Download and install the updated drivers for the motherboard. Mine is an Intel Workstation Board S5520SC. Intel has an INTEL DRIVER UPDATE UTILITY which automatically scaned my Intel system and identified drivers which needed updating. A very handy, time-saving tool!!! Here's the URL: http://www.intel.com/p/en_US/support/detect?iid=dc_iduu
The scan revealed two Intel drivers needing an update:
Intel Chipset
Wired Networking
and one non-intel driver:
Creative Labs Sound Blaster X-fi
I downloaded and installed these three drivers, rebooted, and tested PremierePro, and was extatic to find this resolved the problem.
If you have a motherboard from another manufacturer, then you may want to navigate over to their wibsite to locate chipset and other updated drivers for your motherboard.
ROOT CAUSE:
While Microsoft Windows 7 Ultimate was able to install certain default drivers during the Operating System installation (keeping in mind that this was done on an Intel Solid State Drive that I formatted using Quick Format) these default chipset drivers apparently weren't current and were ultimately the root cuase of the jerky video playback within PremierePro CS5.
Peace

SC 3.2 Solaris 10 x86. When one node reboot, the other one does also

Configured a two node cluster with a EMC clariion san (Raid 6) for holding a zpool and use as quorum device.
When one node goes down, the other one does also.
There seems a problem with the quorum.
I can not understand or figure out what actually goes wrong.
When starting up:
Booting as part of a cluster
NOTICE: CMM: Node cnode01 (nodeid = 1) with votecount = 1 added.
NOTICE: CMM: Node cnode02 (nodeid = 2) with votecount = 1 added.
NOTICE: CMM: Quorum device 1 (/dev/did/rdsk/d1s2) added; votecount = 1, bitmask of nodes with configured paths = 0x3.
NOTICE: clcomm: Adapter nge3 constructed
NOTICE: clcomm: Adapter nge2 constructed
NOTICE: CMM: Node cnode01: attempting to join cluster.
NOTICE: nge3: link down
NOTICE: nge2: link down
NOTICE: nge3: link up 1000Mbps Full-Duplex
NOTICE: nge2: link up 1000Mbps Full-Duplex
NOTICE: nge3: link down
NOTICE: nge2: link down
NOTICE: nge3: link up 1000Mbps Full-Duplex
NOTICE: nge2: link up 1000Mbps Full-Duplex
NOTICE: CMM: Node cnode02 (nodeid: 2, incarnation #: 1248284052) has become reachable.
NOTICE: clcomm: Path cnode01:nge2 - cnode02:nge2 online
NOTICE: clcomm: Path cnode01:nge3 - cnode02:nge3 online
NOTICE: CMM: Cluster has reached quorum.
NOTICE: CMM: Node cnode01 (nodeid = 1) is up; new incarnation number = 1248284001.
NOTICE: CMM: Node cnode02 (nodeid = 2) is up; new incarnation number = 1248284052.
NOTICE: CMM: Cluster members: cnode01 cnode02.
NOTICE: CMM: node econfiguration #1 completed.
NOTICE: CMM: Node cnode01: joined cluster.
ip: joining multicasts failed (18) on clprivnet0 - will use link layer broadcasts for multicast
/dev/rdsk/c2t0d0s5 is clean
Reading ZFS config: done.
obtaining access to all attached disks
cnode01 console login:
Then this on the second node:
Booting as part of a cluster
NOTICE: CMM: Node cnode01 (nodeid = 1) with votecount = 1
NOTICE: CMM: Node cnode02 (nodeid = 2) with votecount = 1
NOTICE: CMM: Quorum device 1 (/dev/did/rdsk/d1s2) added; votecount = 1, bitmask of nodes with configured paths = 0x3.
NOTICE: clcomm: Adapter nge3 constructed
NOTICE: clcomm: Adapter nge2 constructed
NOTICE: CMM: Node cnode02: attempting to join cluster.
NOTICE: CMM: Node cnode01 (nodeid: 1, incarnation #: 1248284001) has become reachable.
NOTICE: clcomm: Path cnode02:nge2 - cnode01:nge2 online
NOTICE: clcomm: Path cnode02:nge3 - cnode01:nge3 online
WARNING: CMM: Issuing a NULL Preempt failed on quorum device /dev/did/rdsk/d1s2 with error 2.
NOTICE: CMM: Cluster has reached quorum.ion ratio 4.77, dump succeeded
NOTICE: CMM: Node cnode01 (nodeid = 1) is up; new incarnation number = 1248284001.
NOTICE: CMM: Node cnode02 (nodeid = 2) is up; new incarnation number = 1248284052.
NOTICE: CMM: Cluster members: cnode01 cnode02.
NOTICE: CMM: node reconfiguration #1 completed.
NOTICE: CMM: Node cnode02: joined cluster.
NOTICE: CCR: Waiting for repository synchronization to finish.
*{color:#ff0000}WARNING: CMM: Issuing a NULL Preempt failed on quorum device /dev/did/rdsk/d1s2 with error 2.{color}*
ip: joining multicasts failed (18) on clprivnet0 - will use link layer broadcasts for multicast
/dev/rdsk/c2t0d0s5 is clean
Reading ZFS config: done.
obtaining access to all attached disks
cnode02 console login:
But when the first node reboot, on the second node this message:
Jul 22 19:24:48 cnode02 genunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0
Jul 22 19:30:57 cnode02 nge: [ID 812601 kern.notice] NOTICE: nge3: link down
Jul 22 19:30:57 cnode02 nge: [ID 812601 kern.notice] NOTICE: nge2: link down
Jul 22 19:30:59 cnode02 nge: [ID 812601 kern.notice] NOTICE: nge3: link up 1000Mbps Full-Duplex
Jul 22 19:31:00 cnode02 nge: [ID 812601 kern.notice] NOTICE: nge2: link up 1000Mbps Full-Duplex
Jul 22 19:31:06 cnode02 genunix: [ID 489438 kern.notice] NOTICE: clcomm: Path cnode02:nge2 - cnode01:nge2 being drained
{color:#ff0000}Jul 22 19:31:06 cnode02 scsi_vhci: [ID 734749 kern.warning] WARNING: vhci_scsi_reset 0x0{color}
Jul 22 19:31:06 cnode02 genunix: [ID 489438 kern.notice] NOTICE: clcomm: Path cnode02:nge3 - cnode01:nge3 being drained
Jul 22 19:31:11 cnode02 nge: [ID 812601 kern.notice] NOTICE: nge3: link down
{color:#ff0000}Jul 22 19:31:12 cnode02 genunix: [ID 414208 kern.warning] WARNING: QUORUM_GENERIC: quorum preempt error in CMM: Error 5 --- QUORUM_GENERIC Tkown ioctl failed on quorum device /dev/did/rdsk/d1s2.{color}
{color:#ff0000}Jul 22 19:31:12 cnode02 cl_dlpitrans: [ID 624622 kern.notice] Notifying cluster that this node is panicking
Jul 22 19:31:12 cnode02 unix: [ID 836849 kern.notice]
Jul 22 19:31:12 cnode02 ^Mpanic[cpu3]/thread=ffffffff8b5c06e0:
Jul 22 19:31:12 cnode02 genunix: [ID 265925 kern.notice] CMM: Cluster lost operational quorum; aborting.{color}
Jul 22 19:31:12 cnode02 unix: [ID 100000 kern.notice]
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651b40 genunix:vcmn_err+13 ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651b50 cl_runtime:__1cZsc_syslog_msg_log_no_args6FpviipkcpnR__va_list_element__nZsc_syslog_msg_status_enum__+24 ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651c30 cl_runtime:__1cCosNsc_syslog_msgDlog6MiipkcE_nZsc_syslog_msg_status_enum__+9d ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651e20 cl_haci:__1cOautomaton_implbAstate_machine_qcheck_state6M_nVcmm_automaton_event_t__+3bc ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651e60 cl_haci:__1cIcmm_implStransitions_thread6M_v_+de ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651e70 cl_haci:__1cIcmm_implYtransitions_thread_start6Fpv_v_+b ()
Jul 22 19:31:12 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651ed0 cl_orb:cllwpwrapper+106 ()
Jul 22 19:31:13 cnode02 genunix: [ID 655072 kern.notice] fffffe8002651ee0 unix:thread_start+8 ()
Jul 22 19:31:13 cnode02 unix: [ID 100000 kern.notice]
Jul 22 19:31:13 cnode02 genunix: [ID 672855 kern.notice] syncing file systems...
Jul 22 19:31:13 cnode02 genunix: [ID 733762 kern.notice] 1
Jul 22 19:31:34 cnode02 last message repeated 20 times
Jul 22 19:31:35 cnode02 genunix: [ID 622722 kern.notice] done (not all i/o completed)
Jul 22 19:31:36 cnode02 genunix: [ID 111219 kern.notice] dumping to /dev/dsk/c2t0d0s1, offset 3436511232, content: kernel
Jul 22 19:31:45 cnode02 genunix: [ID 409368 kern.notice] ^M100% done: 136950 pages dumped, compression ratio 4.77,
Jul 22 19:31:45 cnode02 genunix: [ID 851671 kern.notice] dump succeeded
Jul 22 19:33:18 cnode02 genunix: [ID 540533 kern.notice] ^M

Hi,
the problem lies in the error message around the quorum device. The SC documentation, specifically the Sun Cluster Error Messages Guide at http://docs.sun.com/app/docs/doc/820-4681 explains this as follows:
414208 QUORUM_GENERIC: quorum preempt error in CMM: Error %d --- QUORUM_GENERIC Tkown ioctl failed on quorum device %s.
Description:
This node encountered an error when issuing a QUORUM_GENERIC Take Ownership operation on a quorum device. This error indicates that the node was unsuccessful in preempting keys from the quorum device, and the partition to which it belongs was preempted. If a cluster is divided into two or more disjoint subclusters, one of these must survive as the operational cluster. The surviving cluster forces the other subclusters to abort by gathering enough votes to grant it majority quorum. This action is called "preemption of the losing subclusters".
Solution:
Other related messages identify the quorum device where the error occurred. If an EACCES error occurs, the QUORUM_GENERIC command might have failed because of the SCSI3 keys on the quorum device. Scrub the SCSI3 keys off the quorum device and reboot the preempted nodes."
You should try to follow this advice. I would propose to chose a different QD before trying to do this, if you have one available. Is it possible that this LUN has been in use by a different cluster?
To scrub SCSI3 keys you should use the scsi command in /usr/cluster/lib/sc: ./scsi -c inkeys -d <device> to check for the existence of keys, and ...-c scrub.. to remove any SCSI3 keys.
Regards
Hartmut

My IPad2 will no longer print to my HP5510 photosmart. Both are on same network and both have current software updates. Tried everything and nothing works. What can I do?

My Ipad2 suddenly will not print to my hp photosmart 5510 printer. Both are on same network. Both have most current operating systems and updatees. I tried everything and can not get to work. It was fine two days ago and nothing has changed. What can I do to print again?

Have you tried rebooting your router and iPad?
Turn off your router for 30 seconds and on again.

Secondary Node Rebooted instead of falling to Ok prompt

Hi all,
We need to get system backup for our clustered DB, before and after our maintenance work.
We have the following configuration:
Node #1 and Node #2
Solaris 8
SunCluster 3.0
Oracle 9.3.4
VxVM 3.2
Before issuing cluster shutdown command, I verified which node is primary.
#scstat
I issued scshutdown -y -i0 on the primary node, the secondary node rebooted instead of halting to {ok} prompt. (The primary server successfully fall to ok prompt)
When I checked on the logs on the secondary node.
May 16 08:18:41 SC[SUNW.HAStoragePlus,ttmapd-rg,tmsstor-res,hastorageplus_prenet_start_private]: Global device path /dev/vx/rdsk/tms_usr_dg01/bak_redo11_vol is not recognized as a device group or a device special file.
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost3-res,hafoip_start]: pnm_init: RPC: Rpcbind failure - RPC: Unable to receive
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost0-res,hafoip_start]: pnm_init: RPC: Rpcbind failure - RPC: Unable to receive
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost3-res,hafoip_start]: Failed to validate NAFO group name <nafo0> nafo errorcode <5>.
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost0-res,hafoip_start]: Failed to validate NAFO group name <nafo1> nafo errorcode <5>.
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost0-res,hafoip_stop]: pnm_init: RPC: Rpcbind failure - RPC: Unable to receive
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost0-res,hafoip_stop]: Failed to validate NAFO group name <nafo1> nafo errorcode <5>.
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost3-res,hafoip_stop]: pnm_init: RPC: Rpcbind failure - RPC: Unable to receive
May 16 08:18:42 SC[SUNW.LogicalHostname,ttmapd-rg,tmslhost3-res,hafoip_stop]: Failed to validate NAFO group name <nafo0> nafo errorcode <5>.
Has anyone encountered this error before.
Thank you in advance.
Regards,
Rachele

scshutdown gives a shutdown command on both nodes. here is the procedure.
-failover your resourcegroup to node_2
root@node_2#scswitch -z -g oracle -h node_2
you can check the status of the with scstat
-on the node which you want to backup:
root@node_1#init 0
ok boot -sx
s = single usermode
x = outside of the cluster
Once you're in single usermode, start your backup
If you wish to avoid a bunch of logging on node_2, you can always disable, or set it in maintenance, node_1 on node_2 with scconf:
root@node_2#scconf -q node=node_1,maintstate
(make sure you know what you're doing here)
to reboot node_1 and join it into the cluster:
root@node_1#umount -a
root@node_1#sync
root@node_1#reboot
ok boot (if auto-boot? is set to false)
root@node_2#scconf -q node=node_1,reset
that's it
cheers,
Kim

Losing quorum on 3 node dag with the lose of only 1 node.

We have exchange 2010 latest version and rollups as of June 30, 2014. running on Windows 2008R2 also patched on June 30th. Two nodes in Seattle (primary DC) and 1 node in Spokane (backup DC) active mailboxes are in Seattle site only when running normally.
All 3 servers run MB, CAS and HUB. We are about to LB the CAS on an F5 BigIP box, but that is not in place yet.
We had discovered a few months ago that something is amiss when we were doing updates on the 1 server in Spokane. Normally it would be no issue to suspend replication, patch the server, restart it and resume replication. This would not cause any outages.
Now when we restart that server, or any of the 3 server for that matter, the quorum is lost and the cluster service is terminated on the 2 server that were still up and running when the other was rebooted.
I've been researching this problem and did discover that the 2nd server in Seattle had no vote and have resolved that issue, but the problem continues.
Strangely enough, when looking at Failover cluster Manager, the warning is there next to Quorum configuration that the loss of a node will bring the cluster down, YET when running validation testing, the report says the cluster can survive the failure of
a node. It's contradictory. So we are looking to find out what is the issue. Once the server reboots and is back up, I can manually restart the cluster service on the 2 nodes that were not rebooted and the infrastructure comes up just fine.
However, this is not what a 3 node cluster should do. Any ideas where else to look to resolve this problem?

Thanks. I did remove a few lines that I hope you were not looking for.
some background: Originally this was a 2 node DAG, just in Seattle, a third node was added in Spokane about a year ago. At the 2nd member was sea-mail-02, but it was removed (properly) and sea-mail-03 was added (this was about 5 months ago)
It was not until we did our 3rd DR test that we had some problems getting the DAG to mount in Spokane. We got some help from MS pro support and got things working. Lots of cluster commands were issued in PS and since then, we are having this issue.
RunspaceId                             : 2b8c2445-86c4-41d9-9bbb-cf5a4196a586
Name                                   : DAGWPI
Servers                                : {SEA-MAIL-03, SPOK-MAIL-01, SEA-MAIL-01}
WitnessServer                          : vc-sea01.wpi.com
WitnessDirectory                       : c:\dagwpiwitness1
AlternateWitnessServer                 : spok-vc01.wpi.com
AlternateWitnessDirectory              : c:\dagwpiwitness1
NetworkCompression                     : InterSubnetOnly
NetworkEncryption                      : InterSubnetOnly
DatacenterActivationMode               : DagOnly
StoppedMailboxServers                  : {}
StartedMailboxServers                  : {sea-mail-01.wpi.com, sea-mail-03.wpi.com, SPOK-MAIL-01.wpi.com}
DatabaseAvailabilityGroupIpv4Addresses : {10.ww.xx.47, 10.yy.zz.47}
DatabaseAvailabilityGroupIpAddresses   : {10.ww.xx.47, 10.yy.zz.47}
AllowCrossSiteRpcClientAccess          : False
OperationalServers                     :
PrimaryActiveManager                   :
ServersInMaintenance                   :
ServersInDeferredRecovery              :
ThirdPartyReplication                  : Disabled
ReplicationPort                        : 0
NetworkNames                           : {}
WitnessShareInUse                      :
AdminDisplayName                       :
ExchangeVersion                        : 0.10 (14.0.100.0)
DistinguishedName                      : CN=DAGWPI,CN=Database Availability Groups,CN=Exchange
WhenChanged                            : 6/29/2014 1:46:45 PM
WhenCreated                            : 12/27/2012 12:15:49 PM
WhenChangedUTC                         : 6/29/2014 8:46:45 PM
WhenCreatedUTC                         : 12/27/2012 8:15:49 PM
OrganizationId                         :
OriginatingServer                      : sea-dc01.internal.westernpeterbilt.com
IsValid                                : True

HT1386 I just reinstalled my windows operating system and decided to put on windows 8. After loading all of my music back into a freshly installed itunes, my 4th gen ipod is not recognized by itunes. My 1st gen ipod nano works with no problem. Help!

reinstalled my windows operating system and decided to put on windows 8. After loading all of my music back into a freshly installed itunes, my 4th gen ipod is not recognized by itunes. My 1st gen ipod nano works with no problem. I can eliminate any problems with the cable and connection.
I've stopped and started the service, and also have performed cold reboots.
Nothing seems to have helped the situation.
Help!

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
iTunes for Windows: Device Sync Tests
Have you tried on another computer to help determine if you have a computer or iPod problem?
The iPod Classic uses different drivers than the Nano

Operational Quorum and both nodes rebooting.

Similar Messages

Maybe you are looking for