OPM 2.0RC1 Missing Volume

Hey there, i just deployed the 2.0RC1 OPM in our Testenvironment. It detected the Cluster and after approx 15min he found every Node, Aggregate, SVM but with the Volumes there seems to be a Problem. At first he detected 2 out of 6 Volumes. So not all from the start. One of the deteced Volumes was a cloneed one from a snapshot so i deleted to check if he can only find 2 Volumes. After some Time there was still only the one Volume from before left. The other missing 5 are nowhere to be seen.I checked the Network Communication and the Settings from the OPM to the Cluster and there is no obstacle in the way. Not sure what causes the Problem. Maybe someone here can help.

iHola!
Yes, it's nice n easy.... select the top folder, click n hold, and choose "Update Folder Location". 

Similar Messages

  • NSS4000 missing volumes and shares, but RAID ok?

    We have an NSS4000 with a RAID5 array. We started a large CIFS file transfer to a windows 2003 server from a sharepoint this weekend ironiclly to back up the device and during the file scan process, we encountered communiction errors and the file transfer didn't even start. We could ping the device, but could not log into web admin or mount any shares. We pulled the power cord, put the usb boot drive in the back usb slot as usual and rebooted the device. The device booted up ok we can log into the web admin, the RAID5 array lists OK / healthy, but there are no volumes or shares.
    I found this post
    https://supportforums.cisco.com/thread/2114726
    and thought it was like our case and:
    1. backed up configuration
    2. reset to factory
    3. restored configuration
    4. reset drives (when powered off)
    5. looked over the fstab config files and the seem to have the right volume and shares listed,
    Above did not restore access to shares. After some addtional research, I found reference to shares going missing after improper shutdown, so we created a new volume on the healthly array with the exact same name as before and a single share with same name as before / rebooted. Not exactly sure this was the best idea since I'm not sure what creating a volume and a share might do to actual sectors on the array.
    The array lists 0% used, but the 1.36 array was almost full before this issue.
    Questions:
    1. is there anything else we can try that is within the grasp of non linux experts?
    2. any recommendations for data recovery companies expereinced with recovering data from these devices?
    3. I have contacted http://www.securedatarecovery.com/ for a data recovery quote.  Has anyone used them?
    Thanks for any input.

    Please call us for support to our phone number:
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    Regards,

  • Missing volume bar when adjusting volume

    I have just got HP touchsmart 610, upon updating everything, notice when I adjust volume up or down there is white bar showing up on screen instead individual bars , can't find info where I can update this or perhaps driver is missing any updates for this will be appreciated.. 

    Hello Jake0505
    If you could elaborate a bit on your issue? There are different issues on this thread from the graphical representation of the volume bar being different to it missing. If you could be more specific about your exact issue I will endeavor to help.
    Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Did DreamWeaver CS5 fix the missing "Volumes" in local file paths for "Browse in-"?

    I can't "Browse in Chrome", no matter what I do.
    I tried:
    Re-Installing Chrome. (It's a drag-drop operation. nothing to install )
    Searched in Preferences for a value like the Opendiff to compare documents.
    If you select "browse in Firefox" it works. I don't know whether it's Firefox fixing it's DreamWeaver sending the wrong path, but "Volumes" is there.
    The problem probably only occurs in secondary partitions on the startup drive.
    Apple has not replied about it but it could be Adobe's bug.
    I honestly think the "Volumes" idea to access other partitions (not the startup's default) was introducint late, since other apps seem to have the same issue with non obvious operations (Compare Files Service, Apple OS)
    Has it been fixed in CS5?
    How can I fix it in CS4? I'd glad to hack files if I have to. Re-install is not an option, Com'on! Replace my whole teeth for one caries is not an answer. If the installer can fix it, whoever designed the installer knows what file is the corrupted one.
    Thanks.

    This thread is an extension of the discussion in this thread
    http://forums.adobe.com/message/4184846

  • Missing Volume

    I searched the forums and could not find a problem quite like mine anywhere, so i decided to post this here. My computer started to give me messages saying that many of my files, like my iTunes library and a couple of my documents were damaged. I decided to try to run Disk utility, but it game me a message telling me to restart my computer(the one where it freezes with a black box). so i reset it and got the folder with the ? and the mac os symbol. after trying for hours to get it back on, with both the install disk and a backup disk that i made, i finally got it to turn on. however, the volume that i previously used would not mount and is shown as disk0s10 and is grayed out. it was my main partition on my computer and i have four; one is a backup, one is an emergency(did not work either), and one is for music files and such. I tried to recover it using Disk Utility, and i got a message saying The underlying task reported failure on exit. next i saw a forum saying I should run Tech Tool, and it also said my recovery failed. After i saw this i decided to run tests on the HDD, and it said that my S.M.A.R.T. checks failed:
    Disk Controller
    Saturday, July 22, 2006 12:55:42 PM US/Pacific
    Passed
    Model: WDC WD1600BB-00HTA0
    Mount Point: /dev/disk0
    Capacity: 128.00 GB
    Writable: Yes
    Ejectable: No
    Removable: No
    Class: comfaronics_driverDFXDriver
    Bus: ATA
    Bus Location: Internal
    Revision: 15.05R15
    Socket Type: Internal
    Serial Number: WD-WCAM51023934
    Connection: Master
    disk0s12: Silver
    disk0s14: Gold
    disk0s16: Platnum
    This test checks some of the hardware aspects of the drive itself, including the controller I/O, memory, and head-positioning mechanism. These universal tests are applicable to almost any drive type. Some of the tests can even be performed on CD/DVD drives. These tests include:
    • Diagnostic Check
    • Format Check
    • Rezero Unit
    • Spare Sector
    • Supply Voltage
    • Unit Ready
    Unit Ready Check
    This test determines whether the target drive is able and ready to receive commands.
    Unit Ready Check <Passed>
    Supply Voltage Check
    This test checks that the voltage to the drive is within acceptable limits.
    Supply Voltage Check <Passed>
    Diagnostic Check
    This test initiates a self-diagnostic on the target drive. These routines are designed by the drive manufacturer and provide excellent insight into the operational condition of the drive electronics and mechanism.
    Diagnostic Check <Passed>
    Rezero Unit
    This test is used to determine the target drive's ability to position the actuator at cylinder zero.
    Rezero Unit <Passed>
    Format Check
    This test establishes whether the drive was properly formatted during initial setup.
    Format Check <Passed>
    Spare Sector Check
    This test checks the service tracks to determine whether there are enough spare blocks left for bad block repairs.
    Spare Sector Check <Passed>
    Tests Completed
    Passed
    Read Write
    Saturday, July 22, 2006 12:55:42 PM US/Pacific
    Passed
    Model: WDC WD1600BB-00HTA0
    Mount Point: /dev/disk0
    Capacity: 128.00 GB
    Writable: Yes
    Ejectable: No
    Removable: No
    Class: comfaronics_driverDFXDriver
    Bus: ATA
    Bus Location: Internal
    Revision: 15.05R15
    Socket Type: Internal
    Serial Number: WD-WCAM51023934
    Connection: Master
    disk0s12: Silver
    disk0s14: Gold
    disk0s16: Platnum
    Confirms that data can be reliably written to and read from various locations on the hard drive. These tests include:
    • Read Buffer
    • Write Buffer
    • Linear Read
    • Linear Write
    • Random Read
    • Random Write
    • Seek
    Read Buffer Test
    The Read Buffer test is used in conjunction with the Write Buffer test as a diagnostic function for testing target memory and bus integrity.
    Read Buffer Test <Passed>
    Write Buffer Test
    The Write Buffer test is used in conjunction with the Read Buffer test as a diagnostic function for testing target memory and bus integrity.
    Write Buffer Test <Passed>
    Random Read Test
    This test reads data from a random memory location, verifying the ability of the device to retrieve data.
    Random Read Test <Passed>
    Random Write Test
    This test writes data to a random memory location, verifying the ability of the device to store data.
    Random Write Test <Passed>
    Linear Read Test
    The Linear Read test checks the ability of the drive to read data from a linear data segment.
    Linear Read Test <Passed>
    Linear Write Test
    The Linear Write test checks the ability of the drive to write data to a linear data segment.
    Linear Write Test <Passed>
    Seek Test
    The Seek test provides a test of the initiator to position the device in preparation for access to a particular logical block.
    Seek Test <Passed>
    Tests Completed
    Passed
    SMART
    Saturday, July 22, 2006 12:55:42 PM US/Pacific
    S.M.A.R.T. Self-Checks <Failing!>
    Model: WDC WD1600BB-00HTA0
    Mount Point: /dev/disk0
    Capacity: 128.00 GB
    Writable: Yes
    Ejectable: No
    Removable: No
    Class: comfaronics_driverDFXDriver
    Bus: ATA
    Bus Location: Internal
    Revision: 15.05R15
    Socket Type: Internal
    Serial Number: WD-WCAM51023934
    Connection: Master
    disk0s12: Silver
    disk0s14: Gold
    disk0s16: Platnum
    S.M.A.R.T. stands for Self-Monitoring Analysis and Reporting Technology. This test checks and reports on the status of the S.M.A.R.T. routines built into your drive. These routines monitor important drive parameters as your drive is operating. An examination and analysis of these parameters can aid in the prediction of drive failure. This will allow you to back up your data before your drive fails and the data becomes inaccessible.
    S.M.A.R.T. Self-Checks
    Attribute Normal Worst Threshold Status
    1 Read Raw Error Rate
    1 1 51 Failing!
    3 Spin Up Time
    125 120 21 Okay
    4 Start/Stop Count
    87 87 40 Okay
    5 Reallocated Sectors
    173 173 140 Okay
    7 Seek Error Rate
    200 200 51 Okay
    9 Power On Hours
    84 84 0 Okay
    10 Spin Retry Count
    100 100 51 Okay
    11 Calibration Count
    100 100 51 Okay
    12 Power Cycle Count
    100 100 0 Okay
    194 Temperature
    104 253 0 Okay
    196 Reallocation Event Count
    90 90 0 Okay
    197 Current Pending Sector Count
    176 156 0 Okay
    198 Off-Line Scan Uncorrectable Sector Count
    1 131 0 Okay
    199 Ultra DMA CRC Error Count (Rate)
    200 200 0 Okay
    200 Write Error Count
    1 155 51 Failing!
    S.M.A.R.T. Self-Checks <Failing!>
    Tests Completed
    Threshold levels are exceeded occasionally. You should consider backing up your data from the hard drive. You should continue to check the hard drive for failures.
    S.M.A.R.T. Self-Checks <Failing!>
    SMART
    Saturday, July 22, 2006 12:58:16 PM US/Pacific
    S.M.A.R.T. Self-Checks <Failing!>
    Model: WDC WD1600BB-00HTA0
    Mount Point: /dev/disk0
    Capacity: 128.00 GB
    Writable: Yes
    Ejectable: No
    Removable: No
    Class: comfaronics_driverDFXDriver
    Bus: ATA
    Bus Location: Internal
    Revision: 15.05R15
    Socket Type: Internal
    Serial Number: WD-WCAM51023934
    Connection: Master
    disk0s12: Silver
    disk0s14: Gold
    disk0s16: Platnum
    S.M.A.R.T. stands for Self-Monitoring Analysis and Reporting Technology. This test checks and reports on the status of the S.M.A.R.T. routines built into your drive. These routines monitor important drive parameters as your drive is operating. An examination and analysis of these parameters can aid in the prediction of drive failure. This will allow you to back up your data before your drive fails and the data becomes inaccessible.
    S.M.A.R.T. Self-Checks
    Attribute Normal Worst Threshold Status
    1 Read Raw Error Rate
    1 1 51 Failing!
    3 Spin Up Time
    125 120 21 Okay
    4 Start/Stop Count
    87 87 40 Okay
    5 Reallocated Sectors
    173 173 140 Okay
    7 Seek Error Rate
    200 200 51 Okay
    9 Power On Hours
    84 84 0 Okay
    10 Spin Retry Count
    100 100 51 Okay
    11 Calibration Count
    100 100 51 Okay
    12 Power Cycle Count
    100 100 0 Okay
    194 Temperature
    102 253 0 Okay
    196 Reallocation Event Count
    90 90 0 Okay
    197 Current Pending Sector Count
    176 156 0 Okay
    198 Off-Line Scan Uncorrectable Sector Count
    1 131 0 Okay
    199 Ultra DMA CRC Error Count (Rate)
    200 200 0 Okay
    200 Write Error Count
    1 155 51 Failing!
    S.M.A.R.T. Self-Checks <Failing!>
    Tests Completed
    Threshold levels are exceeded occasionally. You should consider backing up your data from the hard drive. You should continue to check the hard drive for failures.
    S.M.A.R.T. Self-Checks <Failing!>
    Also, As of now the surface Scan has found 49 bad blocks, and has scanned 305536 out of 268435455, and at the rate it is going it will take a couple days to finish, while before when i ran it it would be 10 minutes max. All the other tests passed, and I have not made any recent changes to anything on my computer. I guess what I want to know is if there is any way to recover this partition or the files on it, or if i just lost a large portion of my HDD. I would appreciate anyone helping me out with this problem, or even just pointing me to a better place to put this forum.
    Thanks

    Dak,
    When the SMART status says failing, it is time to get a new hard disk. Also, you will probably be much more likely to maintain current backups of your files on another device. That said, your best course of action is to boot your G4 from another disk, either external or internal, and then attempt to recover files using a utility such as Data Rescue II. Files or directory information written to disk blocks that apparently fail to read back properly will not be recoverable. If (this is a big if) only the directory is lost, then a utility such as Disk Warrior may be of some use.
    In my opinion, purchase any brand of hard drive except Western Digital (I think the WD in your model means this). They have significantly higher failure rates than others; of course any drive can fail at any time. The reason for SMART diagnostic routines is to give the user a warning that things are failing before going completly belly-up.
    Best of luck,
    bd

  • HT204019 Missing "volume adjust" in Ringtones section of new iTunes 12.0

    My iTunes is at its most updated format, 12.0.1.26 How do I increase the volume of a ringtone now?
    In the past, I've made many of my own ringtones using 30-second clips of the songs. Today, when I finished making the ringtones and then imported them into my library, I couldn't find the "volume adjust" slider in the Options tab of "Get Info". It used to be there. When ringtones would first import in, they would always be a little quieter so I had to turn up the volume adjustment.
    That volume slider is no longer in its usual/original place. Is it somewhere else in iTunes?

    I'm having a similar issue, but cannot see anything to do with airplay in the SysPref > Sound menu.  My mac is too old to run Yosemite, so looking to find another way to get this fixed.  Any ideas?

  • Help! Wrting to Missing Volume

    I have formated and Burn finished DVDSP Project. some how it wrote to a volume - an external HD (LaCie) that I renamed it to LaCie 300 so I wil know what size HD I am accessing. I have 2 LaCie and a SeaGate.
    Anyway my burning process failed (bad disk?) - but looks like it wrote Temporary Video_TS and Audio_TS file to a Volume that does not exist. And that Volume is visible from DVDSP's Format and Burn dialog box as Volume/LaCie. I can't delete this temp Video_TS folder and it is occupying 4+GIG of my HD space. It is not visible via Finder nor Disk Utility, nor Spotlight or Search command. It is only visible from DVDSP's menu.
    Help.. I am working on measlty 80GIG PBG4. and I need every mega bytes.
    [email protected]

    I have now changed the preference to write to a drive that actually exist. I think it was a bad disk. or bad disk batch. at least 3 of the blank DVD came back with an error.
    I ended up just creating a Video_TS folder and used Roxio Toast to create the CD. I am still confused with the various format of .img files.
    This might be a general OS X question but where is /volumes/(disk name) Is there a temp folder that OSX writes to.

  • MISSING VOLUME SLIDER BAR SOLVED!!!

    I have found the culprit! It has taken me a very long time to figure it out what it was but it has finally been found. The volume slider disappears when playing music or watching videos but otherwise works.
    The problem is the 32pin connector. If you don't believe me take your phone and place a hard plastic card of some sort (creditcard, school I.D) and place it underneath the 32pin connector. Look at your volume slider and it should appear! You must get your 32pin connector replaced.

    I wouldn't go as fr as getting a new iPod yet. Take it into a genius bar and see what they say. I got my old iPod nano that got sent through the wash replaced for around $50. I don't promise anything.

  • Missing volume sliders

    so i was working on a song, and when I opened the file up (a new one), the individual volume sliders for each track are not there anymore. to adjust the volume for anything I am forced to open the automation line. has anyone ever had this problem before? driving me insane; haven't updated anything and I just can't understand this.thanks in advance for any help or pity you can throw my way.

    that's a weird one.
    first two things to try for “oddball” probs:
    http://www.bulletsandbones.com/GB/GBFAQ.html#oddballprobs

  • Missing volume for "movies" after backup.

    Hi,
    My problem is as follows:
    I recently re-installed my 10.5 and did a TimeMachine backup restore after.
    Unfortunatly the backup did not include the "movie" - folder that residents in "user". (I have a "bypass" on this folder in my TimeMachine-backup because the many gigabytes that very often gets changed in the moviefolder and I forgot to do safety-backup on it)
    So.... now I dont have any "movies"-folder under "user" from the finderwindow and when I try to put a new folder there the link to "movies"-icon in finderwindow does not work. It says that "The volume for "movies" cannot be found".
    How can I restore this link?
    How can I get my "movie"-folder back with the original folder-icon and get it to link with icon in finder-window?
    I have tried to repair the disk from installation-dvd (disk-utility) but no luck!
    I´m VERY thankful for any help!
    Sincerely
    /Richard

    I'm not sure if I've fully understood the problem.
    You can certainly put a new folder into your home folder and call it Movies. Is it that you had your Movies folder in your Finder sidebar and now you find that you click on that you get an error? If so pull that icon out of the sidebar so it disappears and drag your new Movies folder to sidebar instead.
    To get the proper Movie folder icon I would suggest temporarily making a new account with admin privileges. Log on to that account and it will have the OSX created Movies folder. Create a new untitled folder and change its permissions so that everyone has read and write. Then copy/paste the icon from the Movies folder to that folder. Then drop that folder into the home folder of your usual account. Now log back on as that account and copy/paste the icon from the folder you just transferred to your new movies folder. I would trash the transferred folder and empty trash before deleting the account you just created to be sure that permissions don't get stuffed up.
    Of course, maybe someone knows a source for Apples standard icon suite?

  • Missing Volume Bar

    Hi I have a new nano and after a few days use I have lost the volume bar and the song time in minutes and seconds it just appears as a line of dots can anyone tell me if I can get it back. Thanks

    Hi Jill: What you have described is one of the views you can get when listening to the iPod. When a track is playing, you can see elapsed time, album art or rating. The line of dots is the rating (I bet they greyed out meaning no rating set). It may help if you restore you Nano and then re-sync with iTunes. Here's how.... 5R's

  • Missing volume button

      Hi!
    I would like to ask, that if I have lost one of my volume buttons(as funny as it sounds), than I am able to get somewhere a new one? Or being a rare spare part, I won't be able to find or get one in any kind of service.
      Question number two: This problem includes guaranty?

    Your best option is to contact a nokia care point and discuss the problem with them. They can fit spare parts and decide if it will be covered under warranty or not.
    http://europe.nokia.com/support/repair-and-recycle/repair/care-points

  • Missing Volume in NSM

    Hey everyone. We recently did an upgrade of NSM 2.5 to 3.0.2.70 and one of our volumes is not showing up in the storage resource list. I've attempted running a Discover and a Rebuild through the NSMAdmin interface, but it cannot detect this particular volume. I suspect that it may be the volume itself that is the issue, since it's the only one. But it doesn't seem to have any obvious problems as it is currently holding student home directories and is accessible through ConsoleOne and Windows Explorer. Does anyone know what NSM looks for when it's discovering volumes so that I can looks for something specific or perhaps a way to manually add the volume to NSM?
    Thanks, Seth

    Can you check your NSM Engine logs, to find if the engine is reporting
    "invalid namespace"?
    On 1/5/2012 11:36 AM, pbijnen wrote:
    >
    > Same with OES 11 NSS volumes. oes2 sp 3 no problems.
    >
    >

  • Missing volume icon on P755-S5320

    I have a Satellite P755-S5320. Today when I turned my laptop the sound icon that can be found in the taskbar is no longer there, i went to [Turn System icons On or Off] and the sound icon is off but it doesnt let me turn it on, is just gray kind of locked into off mode.
    Any thoughts on how to fix this?

    Satellite P755-S5320 
    Sometimes a simple reboot will fix that. 
    If neither a System Restore not a reboot fixes it, come back here.
    -Jerry

  • Missing photos - duplicate volume

    I'm running iPhoto 7.1.4 with my photo database on a MyBook USB 2.0 drive connected to a Time Machine, accessed wirelessly by iPhoto running on my Mac Book Pro. Previously my photos disappeared and on a Mac forum (not on this site) learned that when a USB drive is disconnected without unmounting it, some applications (e.g., iPhoto) will write to Macintosh HD/Volumes another instance of the missing volume (the errant USB drive) with a "-1" extension.
    I down loaded a copy of TinkerTool so I could see the hidden files and fixed this first instance of the problem as described in the post. Sadly, the problem recurred this evening and I can't find the post. After searching this board again, I thought I'd leave a description of my problem.
    While uploading vacation photos - between one session and another - somehow the connection to the MyBook drive was dropped and iPhoto created a "MyBook-1" entry in my Macintosh HD/Volumes directory. Now the last batch of photos shows up in iPhoto and all my older iPhoto images sport an exclamation mark.
    What do I do to remove the "MyBook-1"? I can easily reload the photos I uploaded to that instance of the volume. I'm much more interested in getting back all the other pictures in the iPhoto database.
    Thanks!

    To fix a damaged library database file that has been corrupted by an interruption see the tip at the end of my signature below. It may help you recover from another interruption.
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
    I've created an Automator workflow application (requires Tiger or later), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 6 and 7 libraries and Tiger and Leopard. Just put the application in the Dock and click on it whenever you want to backup the dB file. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.
    Note: There now an Automator backup application for iPhoto 5 that will work with Tiger or Leopard.

Maybe you are looking for