Optical Drive Tray

Hi everyone, I'm hoping you could help...
My G5 sits on the floor to my left, slightly behind me, and my optical drive was open, with the tray out. I didn't notice, and as I rolled my chair back, I hit the tray and popped out the right side, so now it won't properly slide back in as it should. Left side is still properly attached, though may also be screwed up from my messing around with it. Is there an easy way to rehinge the tray so it goes back in? I don't want to bust it, and I don't want to have to take it apart either.
THANK YOU!
-C

Try to remove your optical drive from your G5, maybe you'll get it fixed, but I guess that you have to replace it: the tray mechanism may be broken.

Similar Messages

Pushing optical drive tray to close / eject key

silly question -- is it a bad habit to push the optical drive tray inward to close it rather than hitting the eject key on the keyboard? for some reason half the time i press the eject key on my keyboard it does nothing .. it's a hassle so i always push the tray in to close it. is it meant to respond to this?

I've had a similar problem but only when Parallels is running. While Parallels is running I can open the CD tray with the keyboard button but it won't close. I have to close it by hand in those situations. I've resorted to pausing Parallels just to close the CD tray lately!

Is it possible to leave the optical drive tray open?

Hello -
I'd like to know if there's any way to have the optical drive tray stay open when shutting down a Mac Pro (PowerPC version, running Leopard)? It's for security reasons in my office to make sure no media is left in after the computer has been shut down.
Thank you.

AppleTV2 has no 'volume control' over optical - it either sends a Dolby Digital 5.1 stream for movies encoded with this or a stereo linear PCM signal. AppleTV1 used to send stereo audio as 44.1 kHz 16 bit (CD quality) whatever it was originally (MP3/AAC/AIFF/WAV), AppleTV2 mucks around and sends a DAT quality signal of 48 kHz 16 bit over optical which yoru Tv may not be able to decode.
Like Rudegar I'd consider the HD4200m as perhaps the model number - some older TVs had the same connections on teh back for a given range, just on lower specced models the connections were not actually connected/enabled.
Another consideration would be whether or not the optical port on the TV is optical out (would not work) rather than optical in.
The lack of analogue connections on AppleTV2 is a nuisance. Send some feedback:
http://www.apple.com/feedback/appletv.html
Won't help current hardware and doubtful any new design but you never know.
AC

I have tried many times to install a SSD drive by using optical drive tray, my MBP is early 2011, intel serise 6, checked on webpage, and someone say SSD could be installed on HDD drive, I guess it could be solved by driver, anyone good idea?

Hi, MBP friends, any ideas for this problem? I tried hard and checked the hardware we have, and it hardly to say the problem from hardware, instead I am thinking it could be solved by driver update, or someone who is good on computer language that could help with the problem.
My computer is early 2011, with intel serise 6 and sata 3 acceptable. I dont know why the opitical drive can not support ssd drive instead.
need help, I really dont want to put my SSD driver to HDD driver, and move HDD driver to optical driver.

well, i have got information from website, and it says it will be harmful to hdd driver set in optical area coz there is no vibration protection function.
i have checked the system, and it says the sata speed is the same 6G and chip intel series 6. it should be the same speed, right?
I am thinking that the chip is the same and mortherboard is the same, the cable is similar as well, why it doesnt work? driver issue? OSX issue? or software issue? firmware?
or simply to say, if i am trying to setup two ssd driver into MBP, it has to be one in opitcal driver area. how could work?
thanks... still in puzzle.
right now, i have reinstall the osx into ssd by usb external, and install it back with opitcal tray, however, when i turn on the computer, the system can not be logged in from SSD, and computer can not read SSD driver, and it says it must be formatted or push out.

Optical Drive tray wont stay closed

My PowerMacG5's optical drive door is stuck open. It will close using any of the normal procedures, but then immediately opens again whether there is a disk in it or not. No matter what I try, the tray always immediately re-opens and stays open. Any help would be greatly appreciated.

Take a close look at the drive when you try to close it and see if the disc tray is hitting something.
This is normal behavior for a drive whose tray is blocked by something, so there may be something in the way.

Optical drive tray will not close

I bought my Hp laptop yesterday and after charging it fully, i decided it was time to investigate. In doing so, I ejected the optical drive - one of the main reasons i bought it and attempted to close it again. But it won't. I have tried several times, not wanting to over do it and break it, but to no avail. Note that I have not damaged it in any way, it just doesn't want to stay shut! How do i get it to close...and stay closed?! Thanks.

, Hello and thanks for posting on the HP support forums. From what you are describing you will have two choices. First and easiest is to take it back to the store for exchange. The sensor for the cd tray is not working right and needs to be pulled and repaired. This will require it being sent in for repair to HP. Contact HP Support. Most stores have a 14 day return policy so with your system being so new it would be much faster. The turn around on a repair could take 10 days. Thanks again for posting and have a great day.

Optical Drive doesn't read DVD's

Hi, I own an HP Pavillion dv7 1279wm entertainment laptop. It came installed with Vista, but I installed a free upgrade to Windows 7 that I got from HP. I had a problem where the drive would not read anything; the disc would spin, but eventually the tray would automatically open and tell me to insert a disc. After using Microsoft FixIt, I was able to read CDs, but encountered the same problem when trying to load a DVD. Previous to using Microsoft FixIt, I did use device manager to uninstall the drive and then reboot so Windows 7 would automatically update the driver. I'm thinking that means that it's not a software problem, but if you can think of anything else I can do (short of swapping out drives because I don't have access to another drive) to rule out it being a software problem please let me know. I realize that combo drives typically use different lasers to read CDs and DVDs, so my guess is that the laser that reads DVDs has failed. If that is the case, where can I find the correct replacement part and how do I install it?
Thanks,
Kevin

Hi Kevin,
If you eject the optical drive tray, you should see just one laser situated towards the centre of the tray - different voltages are applied to this depending on whether it's reading a CD or DVD.
First of all, use a soft, non abrasive material such as cotton or a cotton bud and gently clean the lens.
Check if this has made any difference.
If it still doesn't read DVDs, try following the procedure under the sub-heading 'Let me fix it myself' on the link below to remove the Upper and Lower filters, restart the notebook and see if this helps the issue.
http://support.microsoft.com/kb/982116
If it still doesn't read DVDs, the following procedure will test if your notebook can start from a bootable disc in the optical drive - the advantage of trying this is that it will rule out any possible Windows driver error as the CD/DVD drive is under the control of the Bios when starting the notebook. So if you find that the notebook will not boot from the DVD, then it's almost certainly a Hardware fault in the optical drive itself and it will need to be replaced.
Using another PC to create a Windows 7 Rescue DVD. Download the relevant ISO from the link below.
Windows 7 32bit
Windows 7 64bit
You need use an application such as ImgBurn to correctly burn the ISO to a DVD - a guide on using ImgBurn to write an ISO to a disc is Here. Once created, insert the DVD and then restart the notebook and see if it boots from this disc - if it does, let the first screen come up ( this will show repair options etc ) then just remove the DVD and restart the notebook. If the notebook will not boot from the DVD, it may just load straight into Windows.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How do I open my optical drive without a keyboard

I'm running a Quicksilver Dual 800 G4, without monitor, keyboard, or mouse. I can access it using my MacBook Pro, and view it using Screen Sharing. I want to install software from a DVD onto the dual 800, but how do I open the drive to insert the DVD?
I have another Quicksilver (Dual 867 MDD) which has two optical drives, and on the status bar amidst the airport signal indicator, bluetooth indicator, etc is an eject symbol, which allows me to choose the optical drive I want to open. I have a keyboard connected to this machine, but as the facility exists in OS X to provide that functionality, how can I hack OS X to provide this option in the dual 800 with only one drive?

Thank you for replying. Malcolm (above) managed to provide the exact solution I was looking for at the same time as you were typing your reply, judging from the time.
I'm accessing the QS from my MacBook Pro (OS X 10.5), using a wired/wireless connection - the QS is wired, the MBPro wireless. At the moment they are about twelve inches apart, and I do have a keyboard to plug into the QS, but I'm hoping to set it up as a headless unit to take time lapse photos (using an iSight) and a clever script available here: http://gawker.sourceforge.net/Gawker.html
Once set up, I hope to access the QS remotely, as it will live in Birmingham, and I live in Bristol! So thinking as far ahead as possible, I wanted to set it up to be controlled as much as possible by me, even if my caretaker in Birmingham has to put a disc in the tray from time to time.
Again, many thanks!
kind regards
Andrew McDermott

DVD & Blu Ray Burner Drive Trays Do Not Stay Open When Media is in the Drive

I have a problem with both Windows 8/8.1 and the Windows 10 Technical Preview (there is no issue when I run Windows 7).
I have 2 optical drives: 1) DVD Burner and 2) Blu Ray Burner (I just got the second drive a few weeks ago). They are attached to the secondary SATA Chip (see below for specifics).
The problem I'm having is that when I eject media from either drive, the drive does not stay open, but rather immediately closes. Before I got the Blu Ray Burner, I had this problem with just the single DVD Burner by itself. I was hoping when I installed
Windows 10 Technical Preview that this problem would not be present, but it is present in that O/S as well.
This problem will repeat continuously if I attempt to use the eject button and so I either have to grab the disc while the tray is moving, or if I press the eject button again on the drive at the right time, I can get it to re-open and not close (this
is tricky to get the button timing right as it seems like it has to be done close to when the drive tray is fully extended when it starts retracting). It usually takes me 5 to 10 button presses to get it to stay open. Sometimes it will stay open for about
0.5 to 1s before it closes again, but most of the times it just immediately closes. I also have the same problem if I use the software eject feature by right clicking on the drive and choosing eject.
Of course, the expected behavior is that pressing the eject button should open the tray, but not close it immediately allowing you to remove the disc.
Here is some background information about my system and how the drives are connected:
1. Motherboard: Gigabyte GA-EP45-ED3P Revision 1.0 LGA 775
2. Interface (for both drives): Gigabyte SATA II Chip - 2 x SATA 3 GB/s connectors (GSATA2_0, GSATA2_1) supporting up to 2 SATA 3 GB/s devices
3. Memory: 8 GB (4 x 2 GB)
It should be noted that I tri-boot between Windows 7, 8/8.1, and 10 Technical Preview and that this issue is not present in Windows 7, but has always been there in Windows 8/8.1 and now it is present in 10TP as well.
I've had this system for just over 6 years now and it is still going strong. It should be noted that I have both drives on the secondary SATA chip (as identified above), which is meant to be used with removable SATA devices.
Since the problem exhibits itself in both Windows 8/8.1 and 10TP, a reinstall of the O/S will have no affect on this problem and so this appears to be some other issue that is consistent between Windows 8/8.1 and 10TP.
I'd appreciate your support in looking at this issue - thanks!
Matt Caspermeyer
P.S. I also submitted this feedback through the Insider Program.
Matt

Hey Zagayer,
Thanks for using Apple Support Communities.
As you now have two optical drives in your Mac Pro, you need to be able to choose which drive to eject. That is built into the system. You just hold the Option key while tapping eject for the 2nd drive.
OS X Mountain Lion: Eject a disk
http://support.apple.com/kb/PH10613
If your computer has two optical drives, hold down Option-Media Eject or Option-F12 to eject a disc from the second drive.
Have a nice day,
Mario

[SOLVED] Optical drive no longer detected

Edit:This is so stupid. I had it disabled in BIOS. I don't remember doing it. I apologize for the noise.
I don't know when this happened, but fairly recently. Maybe with linux-3.2 or kmod.
My optical drive is no longer detected. This is what I found in my old logs:
kernel.log.3:Dec 18 22:39:31 localhost kernel: [ 5.277389] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
kernel.log.3:Dec 18 22:39:31 localhost kernel: [ 5.277738] sr 1:0:0:0: Attached scsi CD-ROM sr0
I no longe have any mention of sr0 anywhere and I can't eject the drive. It's completely dead while Arch is booted. It works fine when I'm in the BIOS configuration menu.
Am I missing a module or something like that?
Last edited by Lars Stokholm (2012-01-11 17:05:13)

i agree. in my case only detect CDemu drive
EDIT: restart my machine. now detect all optical drives
Last edited by sl1pkn07 (2012-01-11 03:19:57)

Internal Optical Drive is No Longer Accessible?

My optical drive is not showing up any longer. I cannot open the tray without using a clip. And it is not showing up in my system hardware under disc burning. This has just recently happened. What can I do to access the optical drive again?

Hi-
Welcome to Discussions!
What can I do to access the optical drive again?
Make sure the power and data cables are properly connected.
Reset the PRAM.
Replace the drive.

Optical drive is not reading any disks

Hello,
whenever I insert a disk (cd or dvd) it does not show up in the finder or anywhere else.
Instead: Toast 7 starts and states that it is an empty dvd.
But Toast does recognize the size of the disk (4.5 GB or 7.2 GB for example).
To get rid of that optical disk I have to open terminal and type in "drutil tray eject". Nothing else worked.
The strange thing is, that this problem occured about a week ago and for some strange reason, it dissappeared yesterday. I was able to read several dvds and cds on Friday. Now the optical drive seems to be completly "ignorant" again.
What can I do?
Is the drive really broken?
Thank you for your advice!

Hello,
my DVD-Burner was replaced by the customer support of the Gravis AG in Cologne.
They also replaced my battery which they identified as defect (Actually, I didn't). The Macbook was less than two months old.
Nevertheless, I am happy to have it back and I would like to thank you for your hints and tips.
diverse Mac OS X (10.4.9)
diverse Mac OS X (10.4.9)

External optical drive not found by iMac?

Just purchased an LG Mac Compatible Slim Portable DVD Writer to use with my 2011 iMac because I replaced the internal optical drive with an SSD drive. When I connect the drive via USB I get an initialization error. Any suggestions as to what might work to resolve this? I will contact LG this week but they are closed for the weekend so I thought I would ask here. Here's a pic of the error message:
Thanks.

Reset the SMC > Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.
and NVRAM / PRAM > About NVRAM and PRAM
1. Shut down the computer.
2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
3. Turn on the computer.
4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
6. Release the keys.
Then if it doesn't work, return it for a replacement or different LG External DVD Drive.
Note that while they are bulkier, tray loading AC powered external drive tend to be faster and more reliable than slim USB powered units.

Replacing the Optical Drive on my iMac G4

Disclaimer: Apple does not necessarily endorse any suggestions, solutions, or third-party software products that may be mentioned in the topic below. Apple encourages you to first seek a solution at Apple Support. The following links are provided as is, with no guarantee of the effectiveness or reliability of the information. Apple does not guarantee that these links will be maintained or functional at any given time. Use the information below at your own discretion.
Some of the earliest DVD burners went in to the +iMac (Flat Panel)+ model Macs and many users are now reporting problems with their original drives.
Your initial fault finding should include:
Using a drive cleaning disc to ensure there isn't dust build up on the lens.
Try functionality in another OS X user account.
Ensure that the media you are using is suitable. For example, the maximum write speed for the original drives is 4x DVD-R and these drive cannot burn DVD+R or DVD+RW media.
Revert to a recent, known good, clone of your system (i.e. from a previous software state).
<hr width="200">
If it becomes apparent that a replacement is required outside warranty there are two broad options:
Internal.
Most replacement optical drive models should work under Tiger/Leopard fine. Patchburn will enable operation in Panther/Jaguar.
The DVR-115 (20x DVD±RW DL for $35) has been proved good by several users and is great value.
It's fiddly to work inside an iMac G4 so you must be very cautious, especially around the video cable. Always take anti-static precautions. Here are two options for guiding you through the procedure:
MacWorld
xlr8yourmac
There are also some additional photos which you can find here.
Its worth reading the reports on the xlr8yourmac drive database to get other people's experiences before you commence.
You must replace the Thermal Paste when you close the iMac up or it will overheat.
It's probably worth replacing the PRAM Battery whilst you're in there as these have a finite life (once they fail to re-charge you may start to run into problems - it's only a $5 part).
External.
Certainly a whole lot less effort to install. Should you upgrade to an Intel iMac / Mac Mini / MacBook / MacBook Pro / MacBook Air in the future you'll have access to this faster desktop-spec tray loading drive rather than the slower laptop-spec slot drive installed in these current Macs. This means you'll get 20x burning versus 8x and be able to use small-size and mis-shapen discs.
Here's one example - 20x DVD±RW DL burner again:
OWC - External Optical Drive
Links provided are examples and not specific recommendations of a particular product or retailer.
mrtotes
Do you want to provide feedback on this User Contributed Tip or contribute your own? If you have achieved Level 2 status, visit the User Tips Library Contributions forum for more information.

You can probably just tape it down with package sealing tape. I would just re-use the old stuff. On my recent upgrade, my tape just barely had enough sticky left.
Edit:
Here is a source I found:
http://www.stewmac.com/shop/Electronics,pickups/Supplies:_Shielding/Conductive_CopperTape.html
Pretty cheap, too.
Message was edited by: Keith Barkley

Second optical drive ejects for no reason

I've installed a Pioneer BDR-101A Blu-ray drive in the secondary optical drive bay in my Mac Pro 1,1, which has two 2.66 Dual-core Xeons, 5GB RAM, and an NVIDIA GeForce 7300.
Since installing the Blu-ray drive, the eject button seems to have a mind of its own. Notably, it will eject the tray with nothing in it when the computer wakes up, when I launch Toast, and when I start the computer up. Has anyone else had this problem with a secondary drive in their system. What should I try to make this stop.
Thanks in advance.
Chris

Checked that upon installation. I've now discovered that it ejects when a disc is put into the drive. It sort of can't "hold anything down" and after a few second in the drive, it spits the disc back out.
Thanks for the suggestion.
Chris

Optical Drive Tray

Similar Messages

Maybe you are looking for