Optical Flares obscuration not working

As you see in the picture, I have a logo layer (with transparency) in between an Optical flare and a camera... and I set the Optical flares obscuration to the logo layer (with the transparency) but the flare is still on top of the layer instead of beneath it. What am I doing wrong?

You use collapse transformations on your layer, which changes the processing order and OF doesn't detect the buffer correctly. you can't use it that way.
Mylenium

Similar Messages

  • MacBook Pro Late 2011 : Optical Disk Drive not working?

    MacBook Pro Late 2011 : Optical Disk Drive not working?
    When i try to a put in a cd or dvd; it rejects it automatically within 10-15 seconds.
    I have resetted SMC and PRAM; no chages.
    Don't know what to do. Please help.
    Thank you.

    Clean the heads.
    check to see if it is under warranty.
    buy external DVD/CD rw

  • USB trackball and optical drive do not work in Windows

    When booted in Windows, my new MacBook Pro -- which has no internal optical drive -- does not recognize a USB trackball or my new USB optical drive. Neither appears in the Windows control panel. I downloaded the recommended driver for the trackball, but although I can find the driver installer in Windows' downloads, when run it has no effect on the trackc ball. I worked with two senior Apple support technicans on this problem to no avail. Mac OS 10.10.2

    BC is short for Bootcamp Drivers. These drivers support Apple-specific hardware on your Mac. They can be found at Boot Camp: System requirements for Microsoft Windows operating systems - Apple Support . Assuming you have a 2014 rMBP - Boot Camp Support Software 5.1.5640 should be installed on your MBP. Do you have a Boot Camp option in Control Panel -> System? If yes, then you can Boot Camp: Install or repair Boot Camp drivers and test the devices?
    After you plug-in these devices, do you see any unknown devices (with a yellow triangle and exclamation mark) in Control Panel -> Hardware -> Device Manager? The Apple SuperDrive driver is included in the BC drivers bundle 5.1.5640.

  • Qosmio G30-102 Optical SPDIF out not working

    I have bought new Qosmio G30-102 and I am quite sure that SPDIF Optical Out connector is not working.
    I can't test it at the moment, but I had a couple of SPDIF sound cards and every one of them had a red light on all the time, which signalized that Optical SPDIF is supported.

    Hi,
    maybe I would first try a SPDIF device, if I were you, because I agree with the user before, it has definetively a SPDIF out.
    Greets

  • Optical drive does not work completely.

    My optical drive stopped working today. It is not regonized by the system and does not show up in the ATA Bus in System Profiler.
    I resetted the PRAM and PMU, then checked and the drive was still not found. I then put my computer to sleep and when I woke it up, the drive was there in the ATA Bus list but information was missing. Now it is not there at all.
    There is a disc stuck in the drive. It will not eject. If I restart the computer holding the trackpad button down (to force eject the disc), the system stays on a completely gray screen and never finishes booting.
    The disc was having problems being read on another computer, which is why I put it in the drive. I'm not sure why this has happened, but if anyone has any ideas or tips that they can give me, i'd be more than willing to listen to them.
    Also, I have an eDrive that I made with TechTool Pro, and when I boot up in that the drive is not recognized either. This makes me think that there is a bad connection or a hardware problem. But how is that possible in a Powerbook?
    I do not want to call Apple because I bought my Powerbook two years ago and do not have anymore warranty time left. I can open the machine and look at the drive, but I am guessing that I will not see anything special and it will look normal. I really don't feel like buying another drive, they shouldn't break after two years.
    Maybe there is dirt in it or something?
    When I open Toast, it freezes and never opens. I have to restart my computer to get Toast to close.
    I burned a DVD last night.
    Any help would be appreciated. Thanks.

    I'm not sure if I'm threadjacking here, which probably means I am, but that is not my intent.
    I have seen scattered posts related to this problem and have this problem myself with my 2 1/2 yr old Al PB. Intermittently, the optical drive is not recognized by the system, sometimes with a disc in the drive, sometimes without. System profiler will sometimes list it on the ATA bus, sometimes not. At times it is noted by System Profiler as on the ATA bus, but if I select "disc burning", System profiler either grinds away and never finds anything or says there is no supported device. At one point it froze while playing a DVD and did not recognize the presence of a disc or the drive. A reset of one form or another always corrects the problem (often only after multiple attempts), but this happens several times a week and I shouldn't need to reset PRAM or PMU that often in my opinion. Sometimes just a restart does the trick, but it's all a bit of a pain. No other issues to speak of. Any thoughts? Thanks.
    darth

  • HP Optical USB Mouse Not Working Win7

    I have a HP USB Optical Scroll Mouse (265986-003 MOAFUO) which works on Linux + Mac, but wont work on my Windows 7 PC. I'm pretty sure I've used it before on previous installs of Win7. When I plug it in, it lights up and installs a logitech driver. I've tried the following:
    Uninstalling the drivers - it installed the same one again.
    Checked the HP driver site - no drivers.
    I took the CMOS battery out too
    Any ideas? It does work with other OS's so I'm sure this is something that can be fixed. Maybe a driver issue.
    Thanks for reading.

    I have exactly the same problem.
    However, my dmesg info is slightly different:
    usb 3-2: new low speed USB device using uhci_hcd and address 4
    usb 3-2: configuration #1 chosen from 1 choice
    input: HID 413c:3010 as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input13
    generic-usb 0003:413C:3010.0004: input,hidraw0: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:1d.1-2/input0
    USB HID v1.00 Mouse is the difference, but it also does not work.
    The problem occured after a recent upgrade, I suspect xorg-server.
    Plugging the mouse into the computer results in these messages in /var/log/Xorg.0.log:
    (II) config/hal: Adding input device HID 413c:3010
    (**) HID 413c:3010: always reports core events
    (**) HID 413c:3010: Device: "/dev/input/event10"
    (II) HID 413c:3010: Found 3 mouse buttons
    (II) HID 413c:3010: Found scroll wheel(s)
    (II) HID 413c:3010: Found relative axes
    (II) HID 413c:3010: Found x and y relative axes
    (II) HID 413c:3010: Configuring as mouse
    (**) HID 413c:3010: YAxisMapping: buttons 4 and 5
    (**) HID 413c:3010: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 2
    (II) XINPUT: Adding extended input device "HID 413c:3010" (type: MOUSE)
    (**) HID 413c:3010: (accel) keeping acceleration scheme 1
    (**) HID 413c:3010: (accel) acceleration profile 0
    (II) HID 413c:3010: initialized for relative axes.
    (II) config/hal: removing device HID 413c:3010
    (II) HID 413c:3010: Close
    (II) UnloadModule: "evdev"
    Sequence:
    * hal informs Xorg
    * Xorg configures the mouse
    * but hal removes the mouse ???

  • My apple TV optical connection is not working with optical to analog adapter after the update to 6.0.

    When i bought the apple tv, i could listen to my iPhone's music on my home's audio system, which was connected to the apple tv through a digital to analog audio converter. It was working until the apple tv upgrade to 6.0. I tried connecting the apple tv directly to another amplifier with optical input and it worked fine, i tried the converter on the play station and it worked as well. I switched the DD on the apple tv settings from Auto to on and the problem remains. Any ideas?

    Welcome to the Apple Community.
    Try switching Dolby digital to off.

  • Optical DVD drive not working properly: HP notebook g61

    Game disks and dvd movie disks not working consistently. Sometimes detected as empty dvd disk and asks if I want to burn to the disk. Other times does not read that there is a disk in the drive. Computer is about one month old. On one of my game disks, I have to reinsert 4 or 5 times before it will read properly. Any suggestions?

    Sounds like you use the disk drive a lot. Before we panic and recommend a new drive, try a DVD lens cleaner you can pick up at any place that sells a lot of DVDs, like even WalMart. Run the cleaner disk and see if that helps.

  • APPLE TV OPTICAL OUT LET NOT WORKING

    CONNECTED  APPLE TV TO MY SAMSUNG SOUND BAR VIA OPTICAL OUTLET  NO SOUND AT ALL.
    SOUND THROUGH TV.
    SOUND BAR WORKS WITH OTHER ATTACHED ITEMS LIKE SKY BOX.
    ANY GOOD IDEAS.
    WHEN I FIRST SET UP APPLE TV I DOWNLOADED THE LATEST UPDATE WOULD THIS BE THE PROBLEM.

    George,
    Check the optical audio lead is working properly.  I have a Samsung sound bar working with my 2nd Gen Apple TV.

  • SSD in Optical Bay is not working in a Macbook Pro 15" 2012.

    Can anyone tell me what can be the problem ? At the beginning I could use the SSD from the Optical Bay to read but not to write. Also was impossible to unmount it. I finally wiped it out with the OCZ TOOLBOX and I updated the firmware, but after that was impossible to create any partition. I removed the SSD form the Optical Bay and I moved it back in the 1st bay. Everything is working fine when is connected in the 1st bay. I finally formated the SSD and I put it back in the optical bay, but I still have the same issue, I can't unmount it or format it and I can only read from the SSD. Have in mind that my OS is running from a different SSD.What can I do with it ?
    Many thanks.

    MacBook Pro  / Mozilla Firefox / Netflix / Silverlight Update solved - DON'T DWNLOAD FROM NETFLIX
    I solved this problem tonight. I have a MacBook Pro with 10.5.8. I know, it's old. But I love my Netflix and I recently noticed that Firefox plays Netflix much better.  Then I suddenly got this message that I needed to download the latest Silverlight - it only takes 30 seconds! - WRONG.   However, after much searching, I finally did the steps in order and it worked.  
    This was after repeatedly downloading Silverlight from the Netflix site without success.  So here's what I did:
    1. Went to http://www.microsoft.com/getsilverlight/Get-Started/Install/Default.aspx
    2. Followed the directions. I felt like such an idiot for not doing it right before.
    3. Go to your hard drive and search for "Silverlight" to locate ANY existing Silverlight files: .dmg, etc.
        [also check your Libary/ Internet Plug-ins, but the above search is faster]
    4. Drag it all to the trash and empty it.
    5. Go back to the Get  Silverlight page and click on the Install on that page, not the Netflix site.
    6. Note the steps for Safari or Mozilla Firefox - I wanted Firefox, so I follwed those instructions.
    7. Once it's installed, close all the browsers and Restart that bad boy. Right away.
    8. Open a browser, go to Netflix and proceed to joyfully rot your brain with Netflix content. Yay!

  • Optical Audio Is Not Working with Onkyo Receiver TX-SR501

    Hello,
    I can't seem to make the optical audio from Apple TV work with my Onkyo Receiver TX-SR501. The Onkyo has 2 optical audio lines in in the back. When I hit the "digital input" button on the front of receiver, I can select from OPT1, OPT2, or COAX. I currently have the optical audio line going into OPT2, but if I select OPT2, I hear no sound. Any suggestions?
    Thanks,
    Holly

    I have the exact same receiver (Onkyo TX SR-501) and tgibbs is correct...you must (during a setup process) link each function (DVD, Video 1, Video 2, Video 3, CD, etc.) with its audio source. The Optical cable doesn't connect to a "function" in the back, it connects to an "input". The receiver gives you the freedom to use different inputs with different functions. It's your job, durng the "setup" to map each of these inputs to each function...that way the receiver knows where to go looking for the audio that you are feeding into it for each function you choose. The owners manual has a pretty clear setup process outlined in it.
    Not clear to me that you understood this, so forgive me if I am explaining what is already clear to you.

  • Optical out audio not working

    As per page 27 in the G5 manual, I connected the optical audio out port to my stereo receiver optical input port. No sound from itunes, though it is coming from the computer. I have switched the sound output to "optical digital-out port" in the System Preferences without change (and why would it still be playing from the computer speakers if "built-in audio" is no longer selected?)
    Anything else I should be doing to get music to come out of my speakers? AirTunes is not an option.
    Thanks.

    Duh! Helps to plug the cable into an INPUT port on the stereo rather than the output port. Just in case anyone makes the same mistake....Much better than futzing with AirTunes and the unreliability factor. Just plug an optical cable into the digital aoudio out on the Mac and run it into a vacant optical input port on the stereo and music then comes out both computer and stereo speakers (this is despite the digital optical out choice in the Sounds panel in System Preferences--not sure why it would come out both, but I like it). Works great!

  • Optical audio out not working (incl the solution for me)

    problem:
    new 2011 Mac Mini, 2.5G
    connecting to
    a) TV via HDMI
    b) to a D/A converter and amplifier for a bit better music output
    This worked perfectly for my previous MiniMac that I replace due to my need for speed.
    Now, I could see some red light at the end of the optical cable, but the D/A box did not recognize a signal?
    Furthermore, the Sound switch in Settings would only make the TV play.
    solution:
    after a lot of troubleshooting at the Genius Bar in Beijing (big thanks for that ... the shop is terribly crowded and they never manage to keep the appointments), we found the optical cable to be faulty .... it was apparently bent too much and still had some throughput but not enough to make the receiver read it.
    Nasty one!

    I just purchased this exact same receiver (used). Same issue with Apple TV. Anyone ever figure out to make it work correctly? Thanks.  

  • Optical flow retime not working

    i am using a backup library and event for a project and now the projects retimes with optical flow with 24p photage are really stuttery, they where not this way in the original project ... any idea why? Ive tried different thinks but i am still getting the same results.

    This problem has also crippled my normal workflow for the past few months, but thankfully I think it's been fixed. I ran the latest OSX software update 3 or 4 days ago (I think it's at 10.8.2 now), but was relulcant to check if optical flow was fixed because the notes about the update mentioned nothing about it. Yesterday, however, I dared to try using Optical flow on a clip just to humour myself, but it worked! Try running Software Update and see if that works for you.
    I'm still a little upset though that thoughout the past few months where FCPX users on Mountain Lion complained about this problem, Apple never said a word about acknowledging the issue, that a fix was on the way, or announced that the issue was fixed. I for one sent about 5 feedback bug reports every 2 weeks about the problem and never received a single response.

  • Realtek optical 5.1 not working

    I'm using an e9280t with a yamaha receiver connected through an optical cable (utilizing the factory motherboard optical out).  The first time I connected this was back in november when I got the computer and I got solid, amazing, makes-you-grin surround sound.  I went to play a game tonight and told it I had 5.1 speakers but it didn't play surround.  Long story short, I can no-longer get the realtek-out to give me 5.1, dts, or anything; it only plays stereo.
    My problem is similar to the one discussed on the following thread:
    http://h30434.www3.hp.com/t5/Desktop-PC-Sound-and-​Audio/Windows-7-on-e9280t-has-issues-with-Realtek-​...
    Windows does not detect the connection, but I have never had a problem with actually GETTING sound.  I can even go in to "playback devices -> Realtek Digital Output properties -> Supported Formats" and test it on dts and dolby digital and get it to play out of each speaker.  As soon as I stop the tests though, the indicator on my receiver that tells me which speakers are ACTUALLY being utilized drops from all 6 (sub included) to left and right and stays that way.  I can't even get games that previously worked with surround to work now.
    Also, in "playback devices" when highlighting realtek digital output the configure button is unclickable.
    Briefly: Used to have surround. Don't anymore. Don't know when why or how I lost it.
    Thanks for ANY help!! 

    I expect you have cured your problem but I had similar issue recently
    Advice on this and similar forums suggested removing recent OS updates
    but the cure I for my pc was just to deinstall all sound drivers and re boot and re install
    You may have tried this.

Maybe you are looking for

  • Can you have more than one itunes account on a mac

    is it possible to have more than one itunes account on a mac??

  • Spam email being sent from my AOL account

    Hi All I know there are a lot of posts on this, I have had a look through but nothing seems to mach my circumstances. Early this morning I received a few email failure notifications to emails I didn't send. I checked my sent items and sure enough I h

  • Changing the setting from PDF file to a  JPEG file.

    Is there a way I can change the scan setting on my printer. It is a HP Deskjet F4480. I want to change the setting from PDF file to a JPEG file. I want to scan them so I can see them on my screen saver.

  • ADF Faces OutputText text-align

    I´m working in an ADF Faces Application, a column in a table is showed using an outputText but the customer wants its value is showed right align. I've tried the propertie inlineStyle="text-align:right;" in the outputText but it's not working correct

  • Memory used by servlet

    hi all, i am new to servlets , can someone pls tell me that how can i find that how much memory is my servlet using .iam using tomcat 5. thanx