Optimize update inforamtion between WLC and WCS

Hi,
I have a WCS in 4.1.83 and 3 WLC 4404-2 12AP in 4.1.171.0 (ans ER).
I'm think that the update of information between WLC to WCS are too slow. The update is about inforamtion, like client associated, ....
Do you know if it's possible to change the update pooling of the WCS ?
Thx

Under WCS, Administration, Background Tasks,
you can change the data collection settings

Similar Messages

Vlan management with WLC and WCS

I'd like to know if it is possible to use the same vlan for the management of the WCS and for configuring a wlan?
I try to make this lab and when I declare a dynamic interface that is in the same subnet as the WCS ip address, the reliability between controler and WCS is lost.

I know that I should not put servers on the same vlan as wireless client but I just want to know if it is possible or if Cisco implemented something to avoid this to understand why my lab didn't work with this configuration.
Thanks

How to prevent iTunes for Windows from "Updating iTunes Library"? (Library is on a NAS and managed by iTunes for Mac. Now getting update wars between Mac and Windows versions of the player.

How to prevent iTunes for Windows from "Updating iTunes Library"?
My library is on a NAS and managed by iTunes on a Mac. I can connect from wife's Windows laptop using iTunes for Windows but every time I do, it Updates iTunes Library. Next time I log in from my Mac it Updates iTunes Library in return. It appears I'm experiencing "Update Wars" between the Mac and Windows versions of iTunes. I would like to allow my wife to stream iTunes songs to her new laptop but I don't want any updates from this source... prefer to manage the library from my Mac and not allow Windows to do any thing other than listen to existing playlists.
Thanks for any help/suggestions.

Connect the PC to the library on the NAS. Wait while "updated".
Under Edit > Preferences > Advanced make sure the media folder is correctly pointed at the media folder on the NAS. If not correct, close iTunes, wait a few moments, then open iTunes again.
Close iTunes on the PC. Do not open iTunes on the Mac.
Copy the library files, iTunes Library.itl, iTunes Library Extras.itdb, iTunes Library Genius.itdb, sentinel and the folder Album Artwork into an empty iTunes folder on the PC, for example C:\iTunes.
Click the icon to start iTunes and immediately press and hold down SHIFT. Keep holding until prompted to choose or create a library. Click choose and browse to the copied .itl file, e.g. C:\iTunes\iTunes Library.itl
The library should now work properly on the PC, however check the setting for the media folder. If needs be correct, close iTunes and reopen.
Open iTunes on the Mac. It will update again, but that should be last time.
tt2

WLC and WCS conflict

Hi I am currently using 21 X WLC with N+1 Redundancy and 1X WCS with 1000++ of LAP1020. If had been observed that the antenna type and power TX had been changed with no reason. Is there any settings that may affect with AP customized Tx Power and antenna settings other than using the WCS template to push the configure to the APs instead of the WLC.

Sorry for jumping in on the question with another question but it seemed the right place.
I have an AIR-CT5508-25-K9 WLC and +25AP license : L-LIC-CT5508-25A.
As far as I understand it the WLC should already have a 25AP license installed and with the adder license I should have a count of 50 APs.
However, after installing the adder license the count is still 25.
Could you please let me know if it's just something wrong in my reasoning or should a case be opened?
Thank you,
Barbara

Pages not updating iCloud between iPad and IPhone

Can somebody please help?
My Pages app won't stream the current documents to my iPhone using iCloud .
I've tried everything I could possibly do. I've deleted the Pages app off my iPhone and started again. It just won't update the current documents that reflect on my iPad.
It just has the arrows pointing upwards on the top right hand corner of quite a few documents. This is suggesting that there is no Internet connection when there is. I've tried it over WiFi and on 2 separate Bluetooth pairings with 2 iPhones. Each time it is connected with the Internet but the arrows still suggest otherwise.
I have turned every possible iCloud on in every area. Turned them off then on, reset my phone from scratch doing a clean install not using a previous back up. Still didn't work... Then going back and resetting using a previous back up... Still didn't work :(
I have a 6 month old Mac Mini, the latest iPhone 5 and one month old iPad 4 with the current software updates.....
Please help
Regards Gareth

I believe you are misunderstanding. You don't sync apps between iPad and iPhone, and iCloud has nothing to do with any of this. There is a setting in Settings -> Store where you can set each device to automatically download NEW apps, meaning that when you buy a new app on one device, the other automatically downloads it. However, this is for new downloads only.
For your existing apps, you can simply connect each device to your computer and move the desired apps to it in iTunes. Or you can go to the App Store and re-download those apps.

WLC and WCS licenses

How many APs does wireless controller 5508 and WCS (version 7.0) supports?
Cheers,

Sorry for jumping in on the question with another question but it seemed the right place.
I have an AIR-CT5508-25-K9 WLC and +25AP license : L-LIC-CT5508-25A.
As far as I understand it the WLC should already have a 25AP license installed and with the adder license I should have a count of 50 APs.
However, after installing the adder license the count is still 25.
Could you please let me know if it's just something wrong in my reasoning or should a case be opened?
Thank you,
Barbara

Difference in client tables between WLC and AP controller d0

Hello gang,
Anyone know whether its normal to have an APs' d0/d1 controller output show clients that don't appear on the WLC's "sh client <AP>" output?
Here's an example - 10 clients visible from a "sh client " on the controller, but 15 clients visible on AP4s "sh controller d0" debug.
Granted the User Idle Timeout has been bumped up to 7200 seconds, but shouldn't the AP's d0/1 client table get updated if/when a client roams to another AP nonetheless? Wouldn't this otherwise cause confusion? Is the Split-MAC Split-brained?
Thanks for your input,
--Bruce Johnson
(mcores2wlc1) >show client ap 802.11b mell9s1ap4
MAC Address AP Id Status WLAN Id Authenticated
00:40:9d:31:b0:79 130 Associated 6 Yes
00:40:9d:34:1f:04 130 Associated 6 Yes
00:40:9d:33:ee:04 130 Associated 6 Yes
00:40:9d:2b:d1:6a 130 Associated 6 Yes
00:40:9d:31:23:a3 130 Associated 6 Yes
00:40:9d:33:e9:28 130 Associated 6 Yes
00:40:9d:31:27:a5 130 Associated 6 Yes
00:40:9d:33:eb:4b 130 Associated 6 Yes
00:40:9d:31:22:1d 130 Associated 6 Yes
00:40:9d:33:ee:cb 130 Associated 6 Yes
(mcores2wlc1) >debug ap command "sh cont d0" mell9s1ap4
(mcores2wlc1) >Thu Feb 26 18:54:10 2009: mell9s1ap4:
Thu Feb 26 18:54:10 2009: mell9s1ap4: ---Clients AID VLAN Status Age Tx Mode Enc Key Rate
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eaec 198 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d30.efd1 197 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.bc74 195 6 0000 2800001FF 7165/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.27a5 193 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eecb 192 6 0000 2800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.221d 190 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eb4b 186 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0016.6faf.9d64 185 3 0000 0C00000FF 7186/7200 0-0 0191 200 0-10 10FC0000 06C
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.e928 177 6 0000 2800001FF 5818/7200 0-0 10111 200 0-10 10000000 016
=>Thu Feb 26 18:54:10 2009: mell9s1ap4: 0016.6faf.9db8 176 3 0000 0C00000FF 7140/7200 0-0 0191 200 0-10 10FC0000 06C
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.23a3 174 6 0000 2800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d2b.d16a 165 6 0000 1800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.ee04 163 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d34.1f04 151 6 0000 1800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.b079 147 6 0000 2800000FF 7194/7200 0-0 10111 200 0-10 10000000 016

hi Leo,
I tested this out, but i guess its not working as i thought it would work. I configured the backup primary controller IP and name in the global configuration of the Wireless tab of the WLC and left the AP high availability blank with no settings. I joined the AP to the WLC and show capwap client ha output on the AP shows the backup primary controller name. but if i shut down the primary controller, the AP does not join the back, it just tries to get WLC ip by renewing DHCP forever and stuck in that...   below are the outputs.. any idea why its like this ? I thot if there is no HA configured at the AP level, the global config on the controller level should take effect ?
LWAP3-1042#sh cap cli ha
fastHeartbeatTmr(sec)   7 (enabled)
primaryDiscoverTmr(sec) 30
primaryBackupWlcIp      0xA0A700A
primaryBackupWlcName    WLC2-4402-50
secondaryBackupWlcIp    0x0
secondaryBackupWlcName
DHCP renew try count    0
Fwd traffic stats get   0
Fast Heartbeat sent     0
Discovery attempt      0
Backup WLC array:
LWAP3-1042#
*Apr 30 20:36:21.324: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:36:31.829: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.49, mask 255.255.255.0, hostname LWAP3-1042
*Apr 30 20:37:17.832: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:37:28.337: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.50, mask 255.255.255.0, hostname LWAP3-1042
*Apr 30 20:38:14.338: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:38:24.842: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.51, mask 255.255.255.0, hostname LWAP3-1042
regards
Joe

How can i fix an update issue between iTunes and my iPod Touch

I've recently found my iPod Touch's cable that plugs into the usb drive of my computer. I Downloaded the latest version of iTunes onto my computer, but my ipod hasnt been updated in a while, and when i plug it in, an error pops up in itunes saying I need to unlock my ipod touch in order to sync it. I cannot do this, because when the ipod is turned on/plugged in the only thing that shows up is the image of the ipod cables usb end with an arrow pointing to the itunes logo. How can i resolve this issue and fix my ipod touch?

You need to place the iPod in recovery mode and then restore the iPod via iTunes on its syncing computer. For recovery mode see:
iPhone and iPod touch: Unable to update or restore

Integration between WLCS and Documentum WCM Starter Kit

Has anybody a successful instalation of WLCS and Documentum WCM Starter Kit?
If you answer is yes:
Can you share the files: weblogic.properties, weblogiccommerce.properties
and set-environment.bat?
TIA
Regards
David

The WCM Edition Starter Kit will not install the BEA Integration with 3.2
Commerce Server. One way to solve the problem is to go to the registry key
HKEY_LOCAL_MACHINE/Software/BEA Systems/BEA Weblogic Commerce Server and
look for the folder 3.2. Change the folder value from 3.2 to 3.1 after
installing BEA WebLogic Commerce Server 3.2. Then run the install.
Solution provided by Carmen M. DaCosta (Documentum Technical Support)
"David Solis" <[email protected]> wrote in message
news:[email protected]..
Has anybody a successful instalation of WLCS and Documentum WCM StarterKit?
>
If you answer is yes:
Can you share the files: weblogic.properties, weblogiccommerce.properties
and set-environment.bat?
TIA
Regards
David

Roaming between WLC and vWLC on different code versions

Hi,
I have the following setup in our environment, a HA 5508 pair running 7.4.100 and a vWLC running 7.6.130. I have mobility setup between the two with the control and data path up and running. All the access points are setup for FlexConnect.
When I join an SSID using PSK on an AP associated with the vWLC and then roam to an AP on the 5508, I drop a few pings but stay connected no problem. However when I join an SSID using PEAP (both WLC's using Radius to Cisco ISE 1.2 for this) and repeat the test, my client actually drops my wireless connection and then rejoins.
Is this expected behaviour when running controllers on different versions? This is only temporary until I upgrade the 5508 pair.
Cheers
Brian

Oh... Forgot. With FlexConnect, you also want to create FlexConnect Groups. See this link:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010001111.html
-Scott

ISync no longer updating contacts between computer and RAZR V3x

I have been using iSync for about a month with no problems until now.
Additions or changes to contacts in either the Address Book or the phone no longer get synchronised by iSync.
Calendar events still update fine in both directions.
I have both reset the sync history and reset the device through iSync. Even when resetting the device, nothing changes, all the old entries are still there and no new entries have been transferred from the Address Book.
There are no errors in the logfile, but when I reset the device, in the logfile it states: "[Mac -> Motorola V3x] Contacts changed: 48 added, 0 modified and 0 removed", however I only have 38 contacts in my Address Book.
The memory in the phone is less than 5% full.
Any suggestions as to the cause of the problem and possible remedy?
Macbook Mac OS X (10.4.8)

Hey missychaz,
Thanks for the question. I understand that you are experiencing issues with iCloud Calendar. The following resource may provide a solution. All of the information is relevant for iOS 8 (simply follow the instructions titled for iOS 7):
iCloud: Troubleshooting iCloud Calendar
http://support.apple.com/kb/ts3999
Thanks,
Matt M.

How to share and UPDATE library between PC and Mac

Hi all,
So, I tried to find some info on this problem, and didn't really come up with anything. Maybe a better search is needed, but I was hoping that someone had dealt with this problem and could help me out.
I have Itunes 7 on a Windows XP machine. All of my music is local to that machine. My wife has a Macbook Pro, and wants access to the music as well. She wants access, and wants to be able to create playlists and manage her iPod on the Mac, while I want to do the same on the PC.
The problem with sharing the library is that all control is done on the PC. The problem with her importing the library is that any changes to file information I make on the PC breaks the association on the Mac.
So, what I need is a way to update the library on the Mac when I update the library on the PC. If anyone has any info on this, I would really appreciate it.
Thanks,
Rob

We have upgraded to 7 on both, but both of us have a different Nano - so there isn't enough space to sync all of the library changes. Good thought though, it would probably work if we had a bigger iPod.

HT4623 There is no "Software Update" visible between "About" and "Usage" in General Settings, as shown in the example. And I can't find it anywhere else, either, so I am stymied at the first step of trying to update. Ideas?

I am stymied at the first step of trying to update my IPad software, as there is no "Software Update" choice visible in General Settings. And I can't find it anywhere else, either. Ideas?

Settings>General>Software Update is only available on iPad with IOS 5 and above.
If you are using IOS 4, you need to connect to iTune (computer) to update software.
http://support.apple.com/kb/HT4972

HT4623 i don't have a "software updates" button between "about" and "usage"

cannot update apps, need ios 5 or better. now have 4.3.5 iPad 2

There are some steps half-way down this page : Update your iPhone, iPad, or iPod touch
Before starting the update copy any purchases over to your computer's iTunes library via the File > Devices > Transfer Purchases menu option. And preferably take your own copy of any important documents and/or photos that you have on the iPad - they should be included in the backup but it's best to have your own copy just in case.
Copying photos : http://support.apple.com/kb/HT4083
To copy documents you might be able to use file sharing on your computer's iTunes : iOS: About File Sharing
or you might be able to copy them off via your wifi network or by emailing them to yourself - different apps supports different ways of copying content to/from them.

HT1414 updating app between iphone and itunes

I have an app on my iphone and it says to update using itunes, I updated on itunes and its not updated on my iphone. how can I update my app on my phone?

You didn't mentioned that you synced your phone with iTunes, just that you "updated on iTunes" (which I took to mean that you had updated the app in iTunes, not that you had synced your phone). At any rate, verify that you have checked that app in question as well as checking "Sync Apps" on the Apps tab of your iTunes sync settings, then sync your phone. If it still doesn't transfer, try unchecking that app followed by syncing (which should delete the app from your phone), then check the app again and sync again (which should transfer the updated app back to your phone).

Optimize update inforamtion between WLC and WCS

Similar Messages

Maybe you are looking for