OR modem or not?

Hi just wanted to know if the second line when you tracert a website is the modem (i know the first line is the HH3) 

It's Good to know that your issue has been resolved now...Enjoy

Similar Messages

  • Dial UP Modem is not working properly in Satellite A200-1GB

    My A200 - 1 GB's modem is not working properly. It tries to connect but at last it says remote computer is not responding. As i noticed It has a "Agree" 56kpbs modem.
    It shown as Toshiba Software Modem.
    I tried so many times it doesn't work properly. I tried by changing the assigned COM ports to several other COM ports like COM1,COM10,COM 4 ext... same thing occurs.
    When I diagnose the modem via the modem properties no matters found.
    Same as when I'm dialing through the modem to a telephone (i mean as a call) it's working properly. I mean it can call to a mobile phone or land phone.
    But the same phone line is working properly with my desktop modem as same as another HP laptop modem.
    It seems there is some malfunction on my 56k modem.
    I tried even uninstalling and reinstalling but still the matter exists.
    Can anybody help me in this case?

    Please check this thread:
    http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=109510#109510
    Seems you have started two threads about the same theme.

  • What are the reasons why a wideband modem can not take a CPE?

    I have an M-CMTS with RFGW1.
    I have the following settings:
    int c6/1/3
    downstream Modular-Cable 1/0/0 rf-channel 16-17 upstream 0-3
    int c6/1/4
    downstream Modular-Cable 1/0/0 rf-channel 18-19 upstream 0-3
    cable fiber-node 9
      downstream Modular-Cable 1/0/0 rf-channel 16-19
      downstream Cable6/1/3
      upstream Cable 6/1 connector 12-15
    cable fiber-node 10
      downstream Modular-Cable 1/0/0 rf-channel 16-19
      downstream Cable6/1/4
      upstream Cable 6/1 connector 16-19
    interface Wideband-Cable1/0/0:4
    load-interval 30
    cable bundle 1
    cable bonding-group-id 5
    cable rf-channel 16 bandwidth-percent 45
    cable rf-channel 17 bandwidth-percent 45
    cable rf-channel 18 bandwidth-percent 45
    cable rf-channel 19 bandwidth-percent 45
    the cable modem gets online, but does not take cpe, my question is why?
    D2.0 modems do take CPE, but the 3.0 modems do not. I know that may be a problem in the RFGW1 because another time I changed the port and it worked.
    but I would like to know the reason why only the wideband modems are not taking cpe.
    I'd like to hear from you.
    thanks in advance

    Hi Diego,
    - The first time that was put online, it became as w-online and take CPE (The DHCP assigned IP addresses both, Modem and CPE)- But it did not work, so I reset the modem, and went online again, (but did not have a CPE IP address)
    I'm not following you here. In the first point you mentioned that the modem came w-online and the CPE got an IP. However, in the second point, you mentioned that it didn't work and then you reset the modem. What didn't work (I understood the problem was CPE getting IP address which, as you mentioned, was done on the first point)?
    You also said that, at some point, the modem was online but not pingable. The CPE didn't get IP that time. In that case, was the modem online or w-online? What was the primary channel for this modem? Take into account that, for wideband, the modem uses the primary channel to register and perform all Docsis operation. Any data traffic (like a ping or a DHCP request from a CPE) will use the secondary channels. If these channels have some issue you may see an issue as the one described.
    For the D2.0 modem using Mo1/0/0:16, it could be similar as above. If this channel is OK but the rest have some issues, you could see a behavior like that. The D2.0 modem will use the primary channel (only channel) also for data transfer. Since this channel is OK, the D2.0 modem don't have any issue. However, if a D3.0 modem uses Mo1/0/0:16 as primary it may come online (since the channel is OK) but, if the rest of channels have issues, then you may have problem to pass data traffic.
    Did you check if D2.0 modem can use all the channels? You may also want to check the modulation profiles being used. It could be that you are using a lower modulation profile for ranging (initial, station maintenance) and a higher one for data transfer which may be affected by some condition in the network.
    Best regards.

  • Faxing - Modem Does Not Detect Dial Tone

    Hello Everyone,
    I suddenly have a need to send and receive a Fax. I have a phone line plugged into the modem port on my G4 and on trying to send a text fax, not much happens. Error message to the effect that the modem is not detecting a dial tone. Same cable that works fine on the phone itself.
    Can someone either help with an answer or direct me to a page with more detailed instructions than the "Help" file is providing?
    John

    I have the same problem. I thought I would begin to use my several years old Powerbook to send a simple fax. As it is I have to use my old G3 to fax. Even with Faxstf pro on I still can't get it to work. Fax STF says that the modem is only set to receive and I just cannot change it in the settings. I've trashed the preferences and the program. I am at a loss after having spent a day trying to figure this out. I am on a dedicated phone line that works just fine. I would really like to just simply fax from my powerbook G4. The modem is as follows:
    Modem Model: LastDash
    Interface Type: USB
    Modulation: V.92
    SKU Name: UCJ
    Hardware Version: 4.0
    Firmware Version: APPLE VERSION 2.6.6
    Driver: InternalUSBModem.kext (v2.6.6)
    Country: B5 (United States, Latin America)

  • HT1331 I just bought a airport wireless router I have a time warner cable modem. I have hook up the modem correctly to my new apple airport router and my modem is not working with the apple airport router. what do i need to do?

    I just bought a airport wireless route and I have a time warner modem. My problem is my modem is not connecting to my apple airport router. What do I need to do?

    Power cycle the cable modem.. you may try leaving it off 5min.. might be enough.. sometimes you need 15min or even longer.. Followed by power cycle of the AE.
    Nothing else should be connected to the modem.. except the router that will get the public IP as they only hand out ONE>

  • My droid X2 "modem did not power up, starting rsd protocol"

    Okay, so i shall first start by saying i dropped my phone over 2 months ago but have NEVER had any problems since then, i do not have a warranty on this phone, and i don't have much money to spend. The day before yesterday my phone started showing "no service" and thinking it would be easily fixed by turning my phone off then on i proceeded to do so only to see the error message "modem did not power up (2), starting RSD protocol"! I was shocked, confused and upset. I don't know what to do, i have tried everything. A friend of mine said that since it is a software problem and not because i had dropped it (months back, and was still working perfectly) that perhaps i could take it back and get it fixed for free? Am i to assume this would be the case or is there more i can do at home to save my phone?! Please, please help!

    Try the solutions in this thread. https://community.verizonwireless.com/thread/772503  Motorola forums also suggest to simply remove the sim card and reinsert it.  Good Luck

  • D-Link 562M modem does not works in Solaris 10 (?)

    I use D-Link 562M external USB 56K modem. Modem works in Windows but does not works in Solaris 10 (?). Help me!

    pat.gibbons wrote:
    Not supported yet but will be in a future Solaris Express release.Many USB modems are not really modems but the entire signal processing is done by the host computer. Such "winmodems" require signal processing software which is quite complex. I do not think that such modems are supported in the following versions of Solaris.
    If the 562M is NOT such a modem (but a "real" one) it should be quite easy to adapt a driver to work with this modem.
    Martin

  • SP A10-Error 633: The modem is not installed or configured for Dial-Up

    Ive already reformatted the hard drive and used the utilities CD to install the modem driver again. Anyone got any advice on how to solve problem? Would an external modem solve it?
    By the way it is a satellite pro A10

    Hello
    If the HDD is formatted use the recovery CD and reinstall OS. After that the modem should be recognized and installed properly. After that configure Dial up connection and check the modem. If the modem is not defective it should work.
    The strange thing is that there is error 633 that means: The port is already in use or is not configured for Remote Access dialout.
    Please check this interesting site http://www.modemsite.com/56k/duns633.asp .
    If there is no success please write again.
    Bye

  • Modem will not come online

    The wifi is still connectable on all devices, but will not work. Since the modem is not online we are without both Internet and cable. All of our cable connections are secure and we have tried resetting and unplugging everything. There was a cable guy here this morning and he checked all the connections and managed to get us back online. He said that our signal was good at that point; however, everything went back down as soon as he left. The Internet and cable have both been out for four days now and nothing seems to work.

    Get a tech back out there.

  • Internal modem will not connect

    Hi,
    I have just purchased a used iMac G5 1.6 Ghz and am having problems getting the modem to connect.
    I installed the original version of OSX 10.3.5 and the internal modem would not even show up in the Network pane. I tried doing the install twice and both times got the same result.
    I tried upgrading to 10.3.9 using the MacOSXUpdateCombo10.3.9. and after the iMac restarted and I opened the Network pane I got a message that a new port had been detected "Internal modem" and to check the settings and click "Apply Now". I did that and was then able to enter my ISP settings for the Internal modem. When I open Internet Connect the settings are all correct, but when I try to Connect the modem says it is "Connecting", but I don't hear any dial tone or dialling and after a few seconds it says "Disconnecting" and will continue to do so until I restart the computer.
    Is it possible that the modem is dead and is there any way for me to do a hardware diagnostic to make sure? When I run the Apple Hardware test it just shows "Device found" beside the modem.
    Any help or suggestions would be greatly appreciated as we live in a rural area and a high speed modem is not even an option.
    Thanks,
    Richard

    Welcome to the discussions.
    Try sending a fax (via the print dialog) to a friend.
    If that works, then the problem is not your hardware.
    Thanks Barbara for replying to my problem.
    I tried what you had suggested about sending a fax via the Print dialog and when I look at the Internal Modem window it just says "Preparing fax" and will stay like that until I click on "Stop Jobs". No dialtone, no dialing out, nothing.
    Since I sent the message I have also tried creating a new network location in the Network pane using the Network Setup Assistant and I get as far as a dialog which says "Gathering modem information" that will stay that like that until I quit the Setup Assistant.
    I have also had a look at the system logs in Console and I see this particular line whenever I try to connect with the internal modem:
    localhost kernel: AppleI2SModemfamily::SSIStartUP -- SSIStartUP3034 two sync mode is UNSUCCESSFUL after 20 tries!
    Does this mean that it looks like the modem is definitely dead? Is there no diagnostic tool that will tell me for sure whether the modem is actually dead, before I take it in to a service tech?
    Thanks again,
    Richard

  • My usb modem will not connect to the internet after upgrading to OS X. The modem is active and was issued an IP addreess. There apparently is a connection error between the modem and Safari. Any ideas would be welcomed

    MY USB modem will not connect to the Internet. The modem appears active on either USB ports and an IP address is assigned. The interface between the modem appears to be the problem. Any ideas?

    mcaila wrote:
    Update: I called my ISP (Verizon) and they were not much help.
    What did have you do if anything?
    I also tried to connect with an ethernet cord, and that too is not working.
    What were the results from the Network Diagnostic test when connected by ethernet?
    I've been searching online for hours and have found no solution that has worked.
    What were those solutions that did not work other than what you already mentioned?

  • I Installed Lion and now my USB modem will not work to send a PDF fax? Do I need a new USB modem to send faxes or is there a software update that I need?

    I Installed Lion and now my USB modem will not work to send a PDF fax? Do I need a new USB modem to send faxes or is there a software update that I need? Also can I change the picture of the login screen? That grey mat looks ugly!

    As posted by Ham on July 29 @ 9pm on this thread <https://discussions.apple.com/message/15786976#15786976>.
    Official statement from Apple:
    http://support.apple.com/kb/ht3152

  • My air stream 1200 usb modem did not support in yosemite

    my air stream 1200 usb modem did not support in yosemite

    Have you checked for a new driver/updated software?

  • 3g usb modem does not work on Lion?

         I have had a 3g usb modem for almost two years now, it worked fine on Snow Leopard but does not pick up any connection to any cell tower after my upgrade to Lion. Any suggestions?

    Thank you 'etresoft'. With minimal information from me you have provided a fix to the problem. Although, the cost at 49.5 euros per computer is a bit steep. I think I will just buy a later spec modem at $A79 and be able to use it on all my computers. Regards from iadoreapples

  • Iphone 3G would take connection from modem yet NOT get internet?

    I find this VERY odd. I've used a iphone with a linksys wireless modem. Now it's funny because I came to the apple store to get my iphone 3G's battery replaced but of course, I just got a brand new iphone instead .
    Of course, I did try the wifi since my service was off from AT&T at the moment at my friend's house which worked perfectly fine.
    However, as I just came home right now, I connected to my home's wireless internet that DOES work with my labtop. But for some reason, my iphone says it doesn't get internet for anything just saying "Safari Cannot open the page because it's not connected to the internet" for example when I use Safari.
    Now I reseted everything over and over again and nothing works. And I noticed that it only has the IP Address and Subnet mask in the settings of the network....can anyone help?

    Wow I am feeling stupid by how simple that was. I should've done that as well since it worked.
    Thank you very much my fellow new yorker! (Although I lived in miami most of my life)
    Message was edited by: NinjaZSho

  • Time Capsule & Netgear DG834GT in Modem Mode - Not working

    I've just taken delivery of a 1TB Time Capsule. I've switched my existing Netgear DG384GT modem/router into modem only mode, so routing functionality is disabled. I just want to use the DG834GT as a simple ADSL modem, whilst utilising the features (DHCP, wireless etc) of the TC.
    I've connected the two together, but I can't get a green light on the TC. The DG834GT definitely has an internet connection. I have the TC set to "Share a public IP address", but it doesn't appear to be able to get an ip address from the DG834GT. TCP/IP is set to use DHCP. I've tried everything, without success.
    The only way I've managed to get the working together is by re-enabling DHCP and NAT in the DG834GT, and setting the TC to use bridge mode. This is not what I want to do, as my aging DG384GT has problems when too many wireless devices try to connect.
    Am I missing something? How can I get the TC to obtain the ip address from the DG834GT? I don't want to have to buy an ADSL modem unless I really need to.
    Help!
    Thanks in advance
    Message was edited by: LBowers

    Welcome to the discussions!
    Can you clarify if you have DSL service there? In other words, when you first setup the Netgear to connect to your service, did you enter your user name and password into the device to connect to the internet?

Maybe you are looking for

  • How to back up my external hard drive to another hard drive?

    So I dropped my external Iomega 1TB hard drive and now it wont allow me to back anything up however I can thankfully access everything in there.  Basically I read that I need to back THAT up and format it and start from scratch.  I sucked it up and f

  • Can't install FC on new MacPro - invalid serial number

    I just got my new MacPro and had done the crossgrade to get the universal FCS. I used the sound track pro upgrade to crossgrade to FCS. I went to install and I can't seem to figure out what the valid serial number is. The serial number from my prior

  • PDF printing issues on Windows 7

    I have a pc that is having issues printing pdfs. It is very slow. Here is the steps along with the issues associated with each one. 1. Clicking Print Icon on Tool bar. It freezes momentarily when this happens and states "Not Repsonding". 2. The print

  • WHAT THE HELL?? MDB NOT supported in iAS?!? iAS MDB EJB 6.5

    I have posted a quesation previously about using MDBs within iAS and how toconfigure them. I am now re-reading all the documentation and came across something in Chapter 7 I missed before. "The message-driven bean functionality in iAS is meant for de

  • Setting output to onboard and input to USB interface ?

    Hi all, Does somebody now a way to "split" the input and output in logic? What I want is using my Alesis USB interface for the incoming signals and the onboard (headphone) output for the the master output. The reason is, when recording guitars throug