Ora-03114 in during dbca run in initxml.sql
I'm getting ora-03114 during dbca run in initxml.sql for an 11g db install, it completes the first compile but then fails and continues to fail with ora-03114. This happened before so i trashed the database and started again thinking it may have been a network issue, but its happened again.
any help appreciated.
M.
I'm getting ora-03114 during dbca run in initxml.sql for an 11g db install, it completes the first compile but then fails and continues to fail with ora-03114. This happened before so i trashed the database and started again thinking it may have been a network issue, but its happened again.
any help appreciated.
M.
Similar Messages
-
Hi, I have problem with XE. Sometimes I've get ORA-03114, but server still works and another SQL forms works properly. It's important: this same SQL question sometimes works and sometimes not. Best regards Krzysiek
Check your alert log. You'll usually see an ORA-0600 error as well. Look into the details a bit. Good Luck.
-
Error during SP application.'TP CONNECT SID ' returns ORA-03114 error.
Hi All,
Last week we were applying an Add-On SAPK-510AGINAIN. It was running in
phase IMPORT_PROPER for more than 10 hours without any update in logs.
So I went into SM50 cancelled the work processess. From then when I continue the Add-on installation, I get an error 'TP_CANNOT_CONNECT_TO_SYSTEM' and tp return code 230. When I see
the SLOG, it says R3trans cannot create a process. When I tried
doing 'tp connect PI7 pf=<profile name>, I get a error 'ORA-03114- NOt
connected to ORACLE' and also some SQL Query with ddntt table and few entries.
I also did a DBCHECK, the ABAP Dictionary is consistent with the
Database.Also I suspect the nametab entries should have been
inconsistent state when I killed the work process manually..
Regards
Thilip KumarHi Juan,
Oracle did not go down during SP application.. R3trans -d works fine and also the Transport tool tp check also is fine.. I have even upgraded the kernel to the latest level. STMS is configured for Single system landscape and it is also very well fine..
Please see the output of 'tp connect PIX pf="<TP_PROFILE_>"
TRACE-INFO: 337: [dev trc ,00000] SELECT VERSION, UUID, CRTIMESTMP, ABTIMESTMP, DYTIMESTMP, FLDCNT, TABLENGTH, KEYCNT, KEYLENGTH, CLIE\
TRACE-INFO: 338: 30 0.356722
TRACE-INFO: 339: [dev trc ,00000] NTPOS, TABTYPE, TABFORM, REFNAME, HFLAG, BUFSTATE, BUFPARM, ALIGN, POINTERLG, UNICODELG, COMPCNT, LE\
TRACE-INFO: 340: 27 0.356749
TRACE-INFO: 341: [dev trc ,00000] AFCNT FROM "DDNTT" WHERE TABNAME = :A0; 20 0.356769
TRACE-INFO: 342: [dbntab ,01003] ***LOG BY4=>sql error 3114 performing SEL on table DDNTT [dbntab#6 @ 10038]
TRACE-INFO: 343: 38 0.356807
TRACE-INFO: 344: [dbntab ,01003] ***LOG BY0=>ORA-03114: not connected to ORACLE [dbntab#6 @ 10038]
TRACE-INFO: 345: 31 0.356838
TRACE-INFO: 346: [dev trc ,00000] OCI-call failed with -1=OCI_ERROR 299 0.357137
TRACE-INFO: 347: [dev trc ,00000] SQL error 3114: 'ORA-03114: not connected to ORACLE' 24 0.357161
TRACE-INFO: 348: [dbsloci. ,00000] *** ERROR => Error 3114 in stmt_fetch() from oci_execute_stmt(), orpc=1
TRACE-INFO: 349: 35 0.357196
TRACE-INFO: 350: [dbsloci. ,00000] *** ERROR => ORA-3114 occurred when executing SQL stmt (parse error offset=0)
TRACE-INFO: 351: 33 0.357229
TRACE-INFO: 352: [dev trc ,00000] sc_p=0x110cc4770,no=3,idc_p=0x110cdd560,con=0,act=1,slen=238,smax=256,#vars=1,stmt=0x110fe94e8,table=DDNTT
TRACE-INFO: 353: 34 0.357263
TRACE-INFO: 354: [dev trc ,00000] SELECT VERSION, UUID, CRTIMESTMP, ABTIMESTMP, DYTIMESTMP, FLDCNT, TABLENGTH, KEYCNT, KEYLENGTH, CLIE\
TRACE-INFO: 355: 31 0.357294
TRACE-INFO: 356: [dev trc ,00000] NTPOS, TABTYPE, TABFORM, REFNAME, HFLAG, BUFSTATE, BUFPARM, ALIGN, POINTERLG, UNICODELG, COMPCNT, LE\
TRACE-INFO: 357: 30 0.357324
TRACE-INFO: 358: [dev trc ,00000] AFCNT FROM "DDNTT" WHERE TABNAME = :A0; 20 0.357344
TRACE-INFO: 359: [dev trc ,00000] sc_p=0x110cc4770,no=3,idc_p=0x110cdd560,con=0,act=1,slen=238,smax=256,#vars=1,stmt=0x110fe94e8,table=DDNTT
TRACE-INFO: 360: 98 0.357442
TRACE-INFO: 361: [dev trc ,00000] prep=0,lit=0,nsql=0,lobret=0,#exec=1,dbcnt=0,upsh_p=(nil),ocistmth_p=0x110fe9ec0
TRACE-INFO: 362: 33 0.357475
TRACE-INFO: 363: [dev trc ,00000] IN : cols=1,rmax=1,xcnt=0,rpc=0,rowi=0,rtot=0,upto=4294967295,rsize=60,vmax=32,bound=1,iobuf_p=0x110fb1468,vda_p=0x110feb8c8
TRACE-INFO: 364: 34 0.357509
TRACE-INFO: 365: [dev trc ,00000] lobs=0,lmax=0,lpcnt=0,larr=(nil),lcurr_p=(nil),rret=0
TRACE-INFO: 366: 31 0.357540
TRACE-INFO: 367: [dev trc ,00000] OUT: cols=21,rmax=1,xcnt=1,rpc=1,rowi=0,rtot=1,upto=4294967295,rsize=218,vmax=32,bound=1,iobuf_p=0x110e0d4e8,vda_p=0x110fec028
TRACE-INFO: 368: 34 0.357574
TRACE-INFO: 369: [dev trc ,00000] lobs=0,lmax=0,lpcnt=0,larr=(nil),lcurr_p=(nil),rret=0
TRACE-INFO: 370: 31 0.357605
TRACE-INFO: 371: [dev trc ,00000] SELECT VERSION, UUID, CRTIMESTMP, ABTIMESTMP, DYTIMESTMP, FLDCNT, TABLENGTH, KEYCNT, KEYLENGTH, CLIE\
TRACE-INFO: 372: 30 0.357635
TRACE-INFO: 373: [dev trc ,00000] NTPOS, TABTYPE, TABFORM, REFNAME, HFLAG, BUFSTATE, BUFPARM, ALIGN, POINTERLG, UNICODELG, COMPCNT, LE\
TRACE-INFO: 374: 31 0.357666
TRACE-INFO: 375: [dev trc ,00000] AFCNT FROM "DDNTT" WHERE TABNAME = :A0; 20 0.357686
TRACE-INFO: 376: [dbntab ,01003] ***LOG BY4=>sql error 3114 performing SEL on table DDNTT [dbntab#6 @ 10038]
TRACE-INFO: 377: 38 0.357724
Also the are no dumps as well as system logs for the issue..
Regards
Thilip Kumar
Edited by: Thilip Kumar on Dec 23, 2008 3:44 PM
Edited by: Thilip Kumar on Dec 23, 2008 3:45 PM
Edited by: Thilip Kumar on Dec 23, 2008 3:46 PM -
ORA-12157 during dbca on 10.2.0.4 under SLES 10 SP2
Dear all,
I would like to set up two DBs each in its own ORACLE_HOME running under ASM.
Software installation and ASM setup worked (after some trouble with the multipath storage / ASMLIB). Now I have three separate ORACLE_HOMEs:
/ocfs/oracle/product/10.2/ASM,
/ocfs/oracle/product/10.2/SEQ,
/ocfs/oracle/product/10.2/RESNET.
I can connect to each of them using sqlplus. ASM is up and running.
Now I want ot set up an empty DB in SEQ and RESNET using dbca (or the scripts created by it, if need be).
This worked for SEQ but for RESNET I get ORA-12157 at the last step.
ORACLE_HOME, ORACLE_SID, PATH, LD_LIBRARY_PATH, TNS_ADMIN were all set to point to RESNET. TEMP and TMPDIR are set to /tmp which has several GB free space.
In the trace file ($ORACLE_HOME/cfgtoollogs/dbca/trace.log) I find
[Thread-14] [9:37:4:254] [BasicStep.execute:202] Executing Step : CLONE_DB_CREATION_RMAN_RESTORE
[Thread-14] [9:37:4:255] [StepErrorHandler.setFatalErrors:322] setting Fatal Error: ORA-01092
[Thread-14] [9:37:4:255] [StepErrorHandler.setFatalErrors:322] setting Fatal Error: ORA-01034
[Thread-14] [9:37:4:255] [StepErrorHandler.setFatalErrors:322] setting Fatal Error: ORA-03114
[Thread-14] [9:37:4:255] [StepErrorHandler.setFatalErrors:322] setting Fatal Error: ORA-12560
and
[Thread-18] [9:37:7:496] [BasicStep.handleNonIgnorableError:431] ORA-12157: TNS:internal network communication error
:msg
[Thread-20] [9:37:15:913] [SQLEngine.done:1958] Done called
oracle.sysman.assistants.util.sqlEngine.SQLFatalErrorException: ORA-12157: TNS:internal network communication error
at oracle.sysman.assistants.util.sqlEngine.SQLEngine.executeImpl(SQLEngine.java:1474)
at oracle.sysman.assistants.util.sqlEngine.SQLEngine.connect(SQLEngine.java:821)
at oracle.sysman.assistants.dbca.backend.CloneRmanRestoreStep.executeImpl(CloneRmanRestoreStep.java:244)
at oracle.sysman.assistants.util.step.BasicStep.execute(BasicStep.java:210)
at oracle.sysman.assistants.util.step.Step.execute(Step.java:140)
at oracle.sysman.assistants.util.step.StepContext$ModeRunner.run(StepContext.java:2488)
at java.lang.Thread.run(Thread.java:534)
Can you suggest a solution or a hint on where to look for the cause of this error?
Multi-eye-ringed, gray-haired greetings!please provide some details . It looks like you chose General purpose in DBCA .
Choose Custom Database . -
SQLLDR run command line fails: ORA-03114: not connected to ORACLE
We moved our db (11.2.0.3) to a new server (VM) and cannot get sql loader direct load to run for a non-oracle db owner account without specifying a connection string (@DB). I have the environment set up correctly for this user and can connect to the database via sqlplus.
sqlldr dba1 control=test.ctl direct=yes <==FAILS
Password:
SQL*Loader: Release 11.2.0.3.0 - Production on Fri May 17 13:00:32 2013
Copyright (c) 1982, 2011, Oracle and/or its affiliates. All rights reserved.
SQL*Loader-2026: the load was aborted because SQL Loader cannot continue.
SQL*Loader-925: Error while uldlfca: OCIStmtExecute (ptc_hp)
ORA-03114: not connected to ORACLE
SQL*Loader-2026: the load was aborted because SQL Loader cannot continue.
sqlldr dba1@DB control=test.ctl direct=yes <==SUCCESSFUL
Password:
SQL*Loader: Release 11.2.0.3.0 - Production on Fri May 17 12:59:11 2013
Copyright (c) 1982, 2011, Oracle and/or its affiliates. All rights reserved.My thoughts were along the line that the environment for user x not set up correctly but I verified ORACLE_SID & ORACLE_HOME prior to posting. This user's environment references TNS_ADMIN so I'm sending you the tnsnames.ora from that location.
Please note that I can execute this logged in as the db binary owner (environment set the same as user x).
DWQ1 =
(DESCRIPTION =
(ENABLE = BROKEN)
(ADDRESS = (HOST = xxxx)(PORT = 1521)(PROTOCOL = TCP) )
(CONNECT_DATA =
(SERVICE_NAME = DWQ1)
) -
Ora-03114 running a query with group by
Hi, I've a query with a group by on a sub-query, something like
SELECT <40+ fields>
FROM (SELECT <40+ fields>
FROM table
GROUP BY <40+ fields> I don't have any problem running this query directly via toad. This query is a cursor in a procedure in a package and, if I invoke it on the same data, the session crash "with ora-03114 not connected to oracle". If I modify the query selecting less fields, 22, I don't have any problem while with 23 the crash appears.
Furthermore, I don't have any problem in other databases with similar data.
The db version is 9.2.0.6.0 - 64bit
Any idea/advice?
Edited by: 912104 on 3-feb-2012 2.02
Edited by: 912104 on 3-feb-2012 2.03
Edited by: 912104 on 3-feb-2012 2.03912104 wrote:
I have difficult to have more information, I can only add:
select * from v$version
BANNER
Oracle9i Enterprise Edition Release 9.2.0.6.0 - 64bit Production
PL/SQL Release 9.2.0.6.0 - Production
CORE 9.2.0.6.0 ; Production
TNS for IBM/AIX RISC System/6000: Version 9.2.0.6.0 - Production
NLSRTL Version 9.2.0.6.0 - Production Can I ask what do you think about the different behavior via toad and via package? I mean, it's possible that is a server bug?
Edited by: 912104 on 3-feb-2012 4.02Are you retrieving the entire result set via toad? or just the first few records?
Are there any TOAD non-fetched column values in your result set, i.e. CLOBS, XMLTypes, nested types?
What does your code do with the cursor? Presumably you don't loop through it and do nothing. Are you sure it's the select that's causing the error, or something you are doing with the data in the procedure?
Can you not adding some instrumentation to your code so that you know exactly what line/data values are processed at the time of the crash? Does it always crash on the same values/line or does it vary?
"Furthermore, I don't have any problem in other databases with similar data." ... what do you mean by "similar data". You only need one odd value in one column to cause you a 3114 in the right circumstances. It seems like you are long way off establishing what exactly the problem is. It's always useful not to close doors to lines of thought. You need to systematically track down the root cause of the issue by exclusion and assumptions are the enemy of that process. -
ORA-03113 and ORA-03114 problems
Hi,
I'm experimenting Oracle8i. I'm installing 8.1.7 to RedHat Linux 7.0 out of box without recompiling the kernel. I set the SHMMAX to 0.5*258MB memory on the machine by echoing the number to /proc/sys/kernel/shmmax.
I checked that the system meets the requirements of Oracle's Installation Guide except SEMOPM. The RedHat Linux 7.0 sets it to 32, but Oracle requires 100.
I chose Oracle8i EE Typical Installation. The installation was ok to the point of running root.sh. Several syntax errors occur from root.sh. But they are minor syntax errors. I checked the code, regardless of errors, the scripts accomplished what it intends to do. The installation continued. I choose automatic configure Net8 when it ran Net8 Configuration Assistant and the Net8 Configuration was completed successful.
When it started Oracle Database Configuration Assistant, it created a database. But when it initialized the database, error messages ORA-03114 and ORA-03113 appeared many times. Each time, I chose to ignore. The final message was "Database creation completed with warnings."
After installation, I ran svrmgrl
$svrmgrl
SVRMGR> connect INTERNAL
Connected.
SVRMGR> startup
ORA-03113 end-of-file on communication channel
Checking the meaning of error messages, it says that if ORA-03113 occurs during a connection attempt, check the setup files for the appropriate Net8 driver and confirm Net8 software is correctly installed on the server.
During installation, I chose Local naming method. There are following files in $ORACLE_HOME/network/admin/
listener.ora
sqlnet.ora
tnsnames.ora
shrept.lst
To my layman's eye, they looked ok. I can even telnet to the linux machine with database name, although I don't know how the machine has acquired the alias without any changes to /etc/named.conf nor any changes to any files in /var/named directory.
Please tell me what is correctly installed Net8? or what went wrong and how I should fix the problem.
Thanks,
Wayne
nullI seem to have 8.1.7 creating a database with RH Linux 7.1 now. This was an important clue, since 7.1 hiccups 65% into the link phase of installation, thereby requiring the stubs patch to be run at that time, whereas 7.0 runs quite happily through the install & link without using the patch.
HOWEVER... before invoking dbassist to create the database under 7.1, you apparently need to export ASSUME_LD_LIBRARY = 2.2.5, etc., again, as you would do for the first time installing under RH 7.0.
null -
ORA-00942 Error during unicode export of BI 7.0
Hello Everyone,
I am doing an export of a non-unicode BI 7.0 system to convert and import it into a Unicode database. All the jobs have passed except one and I see the following error in the log file (SAPAPPL0_3.log)
/usr/sap/ABD/SYS/exe/run/R3load: START OF LOG: 20080302124247
/usr/sap/ABD/SYS/exe/run/R3load: sccsid @(#) $Id: //bas/700_REL/src/R3ld/R3load/R3ldmain.c#13 $ SAP
/usr/sap/ABD/SYS/exe/run/R3load: version R7.00/V1.4
Compiled Jun 9 2007 09:20:06
/usr/sap/ABD/SYS/exe/run/R3load -e SAPAPPL0_3.cmd -datacodepage 4102 -l SAPAPPL0_3.log -stop_on_error
(DB) INFO: connected to DB
(DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): WE8DEC
(RSCP) INFO: I18N_NAMETAB_TIMESTAMPS not in env: checks are ON (Note 738858)
(RSCP) WARN: UMGCONTAINER has 1 problems.
(RSCP) INFO: UMGSETTINGS nametab creation: ok.
(RSCP) INFO: Global fallback code page = 1100
(RSCP) INFO: Common character set is not 7-bit-ASCII
(RSCP) INFO: Collision resolution method is 'fine'
(RSCP) INFO: R3trans code pages = Normal
(RSCP) INFO: EXPORT TO ... code pages = Normal
(RSCP) INFO: Check for invalid language keys: active, by default
(RSCP) INFO: I18N_NAMETAB_NORM_ALLOW = 999999999
(RSCP) INFO: I18N_NAMETAB_NORM_LOG = 1000000002
(RSCP) INFO: I18N_NAMETAB_ALT_ALLOW = 10000
(RSCP) INFO: I18N_NAMETAB_ALT_LOG = 10003
(RSCP) INFO: I18N_NAMETAB_OLD_ALLOW = 0
(RSCP) INFO: I18N_NAMETAB_OLD_LOG = 500
(GSI) INFO: dbname = "ABD20070922100908
(GSI) INFO: vname = "ORACLE "
(GSI) INFO: hostname = "ussbbdd5 "
(GSI) INFO: sysname = "HP-UX"
(GSI) INFO: nodename = "ussbbdd5"
(GSI) INFO: release = "B.11.23"
(GSI) INFO: version = "U"
(GSI) INFO: machine = "ia64"
(GSI) INFO: instno = "INITIAL "
(EXP) ERROR: DbSlExeRead failed
rc = 103, table "/BIC/SZTERR_CD"
(SQL error 942)
error message returned by DbSl:
ORA-00942: table or view does not exist
(DB) INFO: disconnected from DB
/usr/sap/ABD/SYS/exe/run/R3load: job finished with 1 error(s)
/usr/sap/ABD/SYS/exe/run/R3load: END OF LOG: 20080302124251
When I run the following command on /BIC/SZTERR_CD, I do not get any table information back. I am not sure how to fix it though.
SELECT * FROM DBA_OBJECTS WHERE OBJECT_NAME = '/BIC/SZTERR_CD ';
I did finish all the unicode preconversion steps and also ran the SMIGR_CREATE_DDL program. I had exported recently from the same system but I never got this error during that run.
Another question is about the order in which the steps need to be performed. I completed the preconversion steps, then ran the SMIGR_CREATE_DDL program before proceeding to the export phase. Is this right or does it not matter?
Thanks again for your help!Hello Stacy,
> When I run the following command on /BIC/SZTERR_CD, I do not get any table information back. I am not sure how to fix it though.
> SELECT * FROM DBA_OBJECTS WHERE OBJECT_NAME = '/BIC/SZTERR_CD ';
If the object does not exists on the source target database, please check if the ddic of sap still contains the table definition. (SE11 or SE14)
If yes you can set the status of the table /BIC/SZTERR_CD to "ok" in the corresponding task file.
You can not fix this problem in other way after you have started the conversion, because of the export files are already generated (with the information of the sap ddic)...
> I completed the preconversion steps, then ran the SMIGR_CREATE_DDL program before proceeding to the export phase. Is this right or does it not matter?
That was the right way.
Regards
Stefan -
Oracle Collaborate Suite ORA-6502 error during loging or form submitting
Hi!
I had Oracle Collaborate Suite ORA-6502 error during loging or form submitting:
Internal error (WWC-00006)
An unexpected error has occurred (WWS-32100)
ORA-6502: ORA-06502: PL/SQL: numeric or value error: character string buffer too small (WWC-36000)
Unexpected error encountered in wwsec_api.person_info (ORA-06502: PL/SQL: numeric or value error: character string buffer too small) (WWC-41417)
Error (WWS-20000)
An unexpected error has occurred (WWS-32100)
ORA-6502: ORA-06502: PL/SQL: numeric or value error: character string buffer too small (WWC-36000)
Unexpected error encountered in wwsec_api.person_info (ORA-06502: PL/SQL: numeric or value error: character string buffer too small) (WWC-41417).
This happened when:
I was using Russian letters in OCS HTML forms (for example - in Administration provision console or in my own HTML forms)
and only I work in Linux (with UTF-8 encoding) (in Windows with win1251 encoding all is OK).
My Database NLS not-null Parameters are:
NLS_LANGUAGE - AMERICAN
NLS_LENGTH_SEMANTICS - BYTE
NLS_TERRITORY - AMERICA
NLS_CHARACTERSET - AL32UTF8
NLS_NCHAR_CHARACTERSET - AL16UTF16
WHAT MUST I DO TO AVOID THIS SITUATION?
Thank
ValeryAll,
It appears that the page Javascript maximum limit size was reached. The error stopped appearing after some of the page Javascript code was removed out to Application Static Files. I wonder if there exists any "direct" indicator by the system whenever the size limit has been reached?
Again, the run error only occurred when the page was loaded in "Debug" mode.
Bernard -
Error: ORA-03114: not connected to ORACLE
While executing the database creation at the middle it is asking for password even if i give password (first attempt ) or empty enter (Last attempt)i'm unable to connect the database.
Password for DBSNMP user:
null [ORA-03114: not connected to ORACLE
Thanks!in my lsnrctl i am unable to see the database
H:\lsnrctl status
LSNRCTL for 32-bit Windows: Version 11.2.0.1.0 - Production on 01-FEB-2013 19:10:31
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1522)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 11.2.0.1.0 - Production
Start Date 01-FEB-2013 19:01:09
Uptime 0 days 0 hr. 9 min. 22 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File C:\oracle\listener.ora
Listener Log File e:\app\username\diag\tnslsnr\mysystem\listener\alert\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1522ipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1522)))
Services Summary...
Service "orcl" has 1 instance(s).
Instance "orcl", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfully
Service "First" has 1 instance(s).
Instance "First", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfullyi am able to see the all the database which running under this instances
After that i pingged the database
H:\>tnsping First
TNS Ping Utility for 32-bit Windows: Version 11.2.0.1.0 - Production on 01-FEB-2013 19:13:47
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
C:\Oracle\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = localhost
)(PORT = 1522)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = FIRST)))
OK (30 msec)where as in tnsping Last i am able to see the database
H:\>tnsping Last
TNS Ping Utility for 32-bit Windows: Version 11.2.0.1.0 - Production on 01-FEB-2013 19:13:47
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
C:\Oracle\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = localhost
)(PORT = 1522)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = LAST)))
OK (30 msec)Last database is in oracleserviceLast
What is wrong with the process. -
ORA-279 signalled during: ALTER DATABASE RECOVER automatic standby databas
Hi,
oracle server:8.1.7.0.0
os:solaris 5.9
we created standby server by taking coldbackup of primary server and we are using rsync to syschronize the archive log files between production and standby servers but every over we recover the standby server by executing
sql>recover automatic standby database:
but in alert log file i am getting the following error :
but when i googled for ora-279 error some people says it is default behaviour and can it be ignored and why it is asking next logfile.
Media Recovery Log /oratranslog/arch_1_1701118.arc
Wed Mar 26 21:35:34 2008
Media Recovery Log /oratranslog/arch_1_1701119.arc
Wed Mar 26 21:35:54 2008
Media Recovery Log /oratranslog/arch_1_1701120.arc
ORA-279 signalled during: ALTER DATABASE RECOVER automatic standby database...
Wed Mar 26 21:36:24 2008
ALTER DATABASE RECOVER CANCEL
Wed Mar 26 21:36:24 2008
Media Recovery Cancelled
Completed: ALTER DATABASE RECOVER CANCEL
Thanks and Regards
Prakash
juniour oracle dbadamorgan,
He is running 8.1.7.0. "DataGuard" scripts were initially available for 9i and then
backported (and available as a seperate download) for 8i. Many 8i implementations
did not and do not use DataGuard.
Even if it is "Jurassic" {which it certainly is NOT}, they obviously do have a good
reason for setting up a standby -- they DO have data of value. So, maybe they have
not upgraded to 9i or 10g. There could be a dozen reasons
1. Server HW/OS doesn't support 9i/10g, not budgetting for Server upgrade
2. Application using Forms 2.x or 4.5 and not tested on 9i / 10g (4.5 not certified
on 9i)
3. Low end client PCs working perfectly with Character-mode forms, not powerful
enought to run Jinitiator and Forms 6i / 9i
Just because someone hasn't upgraded to 10g doesn't mean that they are at fault
when you do NOT know the reason why they have not upgraded.
Surely, they do know that 8i is desupported. Don't you think that their management
has undertaken due diligence / cost-benefit analysis in considering whether they
should upgrade to 10g ?
Maybe they have another project implementing 10g in parallel and will be able
to shutdown this environment soon. Maybe they don't need to do so.
Do understand that people are intelligent enough to make their own decisions
considering their particular circumstances and don't go shooting off with your
assumption that anyone not running 10g is a dinosaur. -
ORA 03114 error
weblogic
Forms 11g
db 11g
winserver 2008 64 bitI am sorry I didn't explain my problem Clearly
My system developed with oracle forms 10g & oracle database 10g
Using oracle application server 10g with win server 2003 32 bit
And It was works properly
Now I upgrade my system to oracle database 11g and weblogic 11g
with win server2008 64 bit
and I tested it it is work no problems but som times when i run my application
if give me this error
frm-40735 unhandled exception ora-03114
and ask for the username and password for database when I give it is give the same error
if I close my Browser and wait sometimes and try agine it is work
why this error happen ………………………….??????
If anyone can help I would be grateful to him .
Thanks -
Oracle Fusion Middleware 11 - Failover - ORA-03114
We use Oracle Fusion Middleware 11.1.1.4 to run a Oracle Forms based application that connects to an Exadata - Oracle 11g 11.2.0.3 database.
In order to test the failover to Data Guard mechanism, we changed the tnsnames.ora to include the stanza for the data guard and disaster recovery databses.
However after changing the tnsnames.ora entry, the Fusion Forms refused to connect. It gave
FRM-40735: ON-ERROR trigger raised unhandled exception ORA-03114
Present below is the tnsnames.ora entry .
The first one is the unmodified one that works(we can open up Oracle forms app and connect successfully to the database).
The second one is the modified one with the failover phrase that does not work - gives
ORA-03114. However the same entry as a jdbc connection string is working fine.
Works :
clientdb_oltp.world =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = client7-scan1)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = clientdb_oltp_srvc.world)
Does NOT work:
clientdb_oltp.world =
(DESCRIPTION =
(LOAD_BALANCE = OFF)
(FAILOVER = ON)
(ADDRESS = (PROTOCOL = TCP)(HOST = client7-scan1)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = client3-scan01)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = client1-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = clientdb_oltp_srvc.world)
(FAILOVER_MODE =
(TYPE = SELECT)
(METHOD = BASIC))))
JDBC Connection string that works :
jdbc:oracle:thin:@(DESCRIPTION_LIST=(LOAD_BALANCE=off)(FAILOVER=on)(DESCRIPTION= (ADDRESS_LIST= (LOAD_BALANCE=on)(ADDRESS=(PROTOCOL=TCP)(HOST= client7-scan1)(PORT=1521)))(CONNECT_DATA=(SERVER = DEDICATED) (SERVICE_NAME=clientdb_oltp_srvc.world)))(DESCRIPTION= (ADDRESS_LIST= (LOAD_BALANCE=on) (ADDRESS=(PROTOCOL=TCP)(HOST=client3-scan01)(PORT=1521))) (CONNECT_DATA=(SERVER = DEDICATED) (SERVICE_NAME= clientdb_oltp_srvc.world))) (DESCRIPTION= (ADDRESS_LIST= (LOAD_BALANCE=on) (ADDRESS=(PROTOCOL=TCP)(HOST=client1-scan)(PORT=1521))) (CONNECT_DATA=(SERVER = DEDICATED) (SERVICE_NAME=clientdb_oltp_srvc.world))))
Could you please advise if there is any reason why Oracle Fusion Middleware will not connect with the tnsnames.ora having the failover stanza ? Does the above entry require any change ?
We have already checked for any TAB or other non-print characters.
Edit : 6/3/2014 I mistakenly gave the Forms Oracle error as ORA-12154. The error faced is "FRM-40735: ON-ERROR trigger raised unhandled exception ORA-03114"
Updated Title and description.
The credentials were validated multiple times. (user id and password is correct)
Message was edited by: skrishnanHi Prakash,
The database is up and running. We are able to login to it using sqlplus and other sql tools from different clients(sql client and java based programs).
We believe its either due to Oracle Middleware not supporting the tnsnames.ora entry with the failover stanza , or some quirk with our tnsnames.ora file.
Is there anything you would advise that we try ?
Thank you,
S. Krishnan -
Frm-40735 when-button-pressed trigger raised unhandled exception ora-03114
hi everybody,
i am using oracle 10g release 2 in my test server and 10g release 1 in production server with forms in 10g running through the oracle 10g application server with no problem with our production server.
but the same form when i try to use through the same application server for my
with my test database server which is oracle 10g release 2 is giving me
frm exceptions and disconnecting the session.
like i get frm-40735 when-button-pressed trigger raised unhandled exception
ora-03114. then frm-40655 sql error forced rollback;clear form and reenter transaction. then when i try to exit it shows ora-24324 service handle not initialized.
The same thing when i try with my production server i dont get any exception handle error or forced rollback error.
i am not facing any problem as such to connect to my test database(release 2)
through sql plus client or TOAD OR ENTERPRISE MANAGER THEY ARE ALL FINE. IT IS ONLY WHEN I GO THROUGH THE APPLICATION SERVER TO ACCESS MY FORMS I GET THIS ERROR. BUT MY PRODUCTION IS RUNNING THE SAME WAY WITH NO ERRORS.
any suggestions welcome as i have to bring release 2 in the production next month
thanks and regards
manishORA-03114 not connected to ORACLE
Cause: A call to Oracle was attempted when no connection was established. Usually this happens because a user-written program has not logged on. It may happen if communication trouble causes a disconnection. In addition, this message could occur when ALTER SYSTEM KILL SESSION or ALTER SYSTEM DISCONNECT SESSION were issued with the IMMEDIATE qualifier because, in those cases, the client's connection to the database is terminated without waiting for the client to issue a request.
Action: Try again. If the message recurs and the program is user written, check the program.
zaibi. -
ORA-04045: errors during recompilation/revalidation
I was applying catlog.sql and catproc.sql, but has some problem during it, and now, when I try to access a database in the sqlplus appear follow errors:
ERROR:
ORA-04045: errors during recompilation/revalidation of
SYS.DBMS_APPLICATION_INFO
ORA-06508: PL/SQL: could not find program unit being called
ORA-06512: at line 2
ORA-06508: PL/SQL: could not find program unit being called
ORA-06512: at line 2
Error accessing package DBMS_APPLICATION_INFO
Someone know about it ??
ThanksWhat went wrong during catalog and catproc ?
Did you run out of space ? In that case just enable autoextension on the system tablespace datafile[s] and re-run catalog & catproc. Check the logfiles.
regards,
Ronald.
http://ronr.nl/unix-dba
Maybe you are looking for
-
Receiving mms texts with AT&T what a pain to get in the account!
Ok when I get an mms I gotta go to that link and put in the message I'd and a pass word. No matter how many tes I type and retype it t won't log In. Is there an easier way? Why does the message I'd and pass gott be different every time I ger a mms?
-
What setting do i need to set up airprint
what setting do i need to set up airprint
-
SCHEMA: Flat vs. hierarchical
All, I'd like your feedback on another topic relating to the schema, this one at a higher level. Basically, the question is whether you think we should adopt a flat schema, or a hierarchical schema. To explain: - With a flat schema, we assign some nu
-
Upgraded to OS X & LOST access/use/print OS 9 documents & mail!
Had a technician install a new hard drive and operating system, but was the old system and the new one are not integrated. I used mostly email and word documents on OS 9. Now, all of my email is gone. And when I want to see an old document, OS 9 star
-
Mountain lion is not downloading (icon says waiting)
when i tried to downloaded the first time i had an unstable internet access but now that i dont it wont download what should i do?