Oracle 10G in HP Unix
Hi,
I am going to install Oracle 10G on Hp Unix. Is any one have any document about installation of Oracle 10g in HP Unix other than Oracle Documentation?
Thanks in advance.
Jayanta
Is any one have any document about installation of Oracle 10g in HP Unix other than Oracle Documentation?Anything wrong with Oracle documentation?
Similar Messages
-
Oracle 10g RAC and Unix *rlogin* question
I support several 10g RAC databases, running on IBM pSeries servers using AIX 5.3. Our database and clusterware are 10.2.0.3 and 10.2.0.4.
I understand that user equivalence and rsh/ssh must be enabled in order for the RAC environment and clusterware to communicate across all of the cluster nodes.
My problem is a question being raised by our internal system auditors. The are requesting that the rlogin and exec commands for AIX be disabled, because they feel it is a security risk. Both commands prompt for a valid userid and password when they are used to remotely login or execute a command.
I have reviewed the RAC documentation online, and searched Metalink (I am not a Metalink expert, though!) as well as Google and can't find anything stating that rlogin and exec are specifically required in order for RAC to function properly.
Can anyone offer advice or their perspective on whether or not these two commands need to be enabled in order for RAC to function?
Thank you in advance for any assistance you can give to me.
Regards,
MarkHi Mark,
as far as my knowledge goes RAC does neither use rlogin nor exec commands.
After you setup the cluster Oracle communicates simply via. TCP (clusterware) and UDP (RAC) and is only sending and recieving messages. There is no need during runtime for a remote login.
So als ssh and rsh are solemnly used for installation and patching (not for communication).
Still Oracle recommends to leave them enabled, since it makes life easier than to enable ssh each time a patch is needed.
Sebastian -
Recover Table in Oracle 10G - Very Urgent--Kindly Help
Hi Guru
I m using oracle 10G R2 in Unix. One of the user has unfortunately updated the table with wrong dataa aand hence we need to recover the table.
Our DB does not have flashbaack databaase option on.
For recovering the table using Flashback table point in time recovery, do we reqquire flaashback database option on?
If so then how can i recover the table?
Can i recover it theough RMAN??
Kindly Advise.
Thanks
Ram
Edited by: user448837 on Jan 8, 2010 5:55 PMI understand, but your post implies ("Because I have..") that you need to set a proper value for DB_FLASHBACK_RETENTION_TARGET for FLASHBACK TABLE to work and this is not the case.
For example:
SQL> ALTER SYSTEM SET DB_FLASHBACK_RETENTION_TARGET=1;
System altered.
SQL> CREATE TABLE TEST AS SELECT * FROM DUAL;
Table created.
SQL> ALTER TABLE TEST ENABLE ROW MOVEMENT;
Table altered.
SQL> SHOW PARAMETER DB_FLASHBACK
NAME TYPE VALUE
db_flashback_retention_target integer 1
SQL> SHOW PARAMETER UNDO
NAME TYPE VALUE
undo_management string AUTO
undo_retention integer 86400
undo_tablespace string UNDOTBS
SQL> DELETE FROM TEST;
1 row deleted.
SQL> COMMIT;
Commit complete.
SQL> BEGIN DBMS_LOCK.SLEEP(120); END;
2 /
PL/SQL procedure successfully completed.
SQL> FLASHBACK TABLE TEST TO TIMESTAMP SYSTIMESTAMP - INTERVAL '2' MINUTE;
Flashback complete.
SQL> SELECT * FROM TEST;
D
X -
Oracle 10g connection issue..
Hi ,
I have oracle 10g installed on one unix box and i need to connect to this oracle 10g from another unix box
using the sqlplus client version 9.2.0.7.0.
When i try to connect using sqlplus 9.2.0.7.0 i am not getting any response.
is it possible to connect to oracle10g using sqlplus 9.2.0.7.0?
Thanks.Zymson wrote:
I have oracle 10g installed on one unix box and i need to connect to this oracle 10g from another unix box
using the sqlplus client version 9.2.0.7.0.
When i try to connect using sqlplus 9.2.0.7.0 i am not getting any response.You failed to provide any meaningful information in order to diagnose the problem.
I suggest that you start off with some basic tests first.
1. Ping
Can you ping the remote server? On the local Unix box, use the dotted IP address of the remote Unix box and determine if it responds. E.g.
ping <IP_ADDRESS>
2. Hostname resolution
Ideally you want to use the hostname (instead of dotted IP) of remote Unix box. Determine if the local Unix box resolves the remote Unix box's hostname. E.g.
ping <HOSTNAME>
3. Oracle port connectivity
Next you need to test if the TCP port used by the Oracle Listener on that remote Unix box is reachable from the local box (and not firewalled for exampled). Telnet into this port (if the connection is accepted, press enter a few times and the telnet connection will be terminated by the listener). E.g.
telnet <HOSTNAME> 1521
4. Test SQL*Plus connectivity
Once you've established that connectivity to the remote Listener is working, you need to test the TNS connection string and ensure that the connection parameters (such as ORACLE SID) that is passed to the Listener is correct. E.g.
sqlplus scott/tiger@"(DESCRIPTION= (ADDRESS= (PROTOCOL=TCP)(HOST=<HOSTNAME>)(PORT=1521)) (CONNECT_DATA= (SID=<ORACLE_SID>) (SERVER=dedicated)))"
Once all ths is working, should you update the local Unix box's tnsnames.ora file with the TNS connection string and use that TNS alias for connecting via SQL*Plus.
If any of these steps do not work, post the full details of the step PLUS the actual error information (error codes and error messages). -
Oracle Streams: Oracle 10g in Unix to Oracle 10g in Windows 2003
Hello,
At our company, we wish to migrate one of our Oracle 10g databases from Windows 2003 to Unix environment. With this new Oracle database in Unix, we would like to connect it via Linked Streams to another Oracle 10g database in a Windows 2003 environment.
My question is: Is this possible? If so, what middleware/other components would we need to set this up?
Thanks!
Edited by: user3031139 on Sep 16, 2008 7:18 AMYou can use any of the samples in the official Oracle docs:
http://download.oracle.com/docs/cd/B19306_01/server.102/b14229/pt_demos.htm#sthref1277
http://download.oracle.com/docs/cd/B19306_01/server.102/b14228/ptrep_demos.htm#BEIDDCBI
There is simply nothing special that has to be done for the different OS. -
Problem with do click on a field - Oracle 10g form - UNIX
Hello, friends.
I nedd a help. I have a problem with a Oracle 10g form when it was executed in UNIX environment.
The problem is that when I do click with the mouse in a different field, doesn't lead me to the other field. That is, don't let me to do click on a different field than the initial field of the form. Just work with TAB or ENTER.
Would you tell me what I can check?
Thanks.
Kisses.
AnnieHello
Another question about the problem that I posted yesterday:
Why the system.cursor_item isn't change when I do click in other field? Just the system.mouse_item changes. This problem occurss in Oracle 10g at UNIX environment (don't occurss in Windows environment).
Thanks.
Kisses.
Annie -
Enter prise Manager Oracle 10g Rel 2 ON HP-Unix - Errors
Hi all
I am using Oracle 10g Release 1002000100 on HP-Unix,
When i am trying to login the Enterprise manager it is Throwing the ERROR
java.lang.Exception: UnknownHostException sending request :: testdisc And Enter prise manager page is being Opened
But
when i am clicking the Performance or Administration tabs it is comming to Login page with the Follows Error message
Io exception: The Network Adapter could not establish the connection
cud u any one advise about this Problem
many thanks
- KhajaCheck the metalink note, *273758.1* for the same.
HTH
Aman.... -
Can I call host file ( Unix Shell script ) from Oracle 10g trigger
Hi,
I am new to Oracle 10g. Can I call host file ( unix shell script ) from Oracle 10g trigger ?. I know it is possible. Pl explain me with small example
thanks & regards
paraguser12009546 wrote:
Hi,
I am new to Oracle 10g. Can I call host file ( unix shell script ) from Oracle 10g trigger ?. I know it is possible. Pl explain me with small example
thanks & regards
paragIf you are in 10g, you can simple call shell script from DBMS_SCHEDULER:
BEGIN
DBMS_SCHEDULER.CREATE_JOB (
job_name => 'TEST_SCRIPT',
job_type => 'EXECUTABLE',
job_action => 'PATH_OF_YOUR_SCRIPT',
start_date => SYSDATE,
repeat_interval => 'FREQ=MINUTELY; INTERVAL=1',
enabled => TRUE,
comments => 'Shell script from Oracle'
END;
/ -
[질문] unix 에서 php와 oracle 10g 를 연동하고 있는데요 한글데이터가 ? 로 나와요
os : unix AIX 5
db : oracle 10g
웹 : apache, php
이렇게 구성되어 있는데
oracle, php 설치를 했는데요
웹은 뜨는데
쿼리를 해서 한글 데이터를 조회하면 한글이 ?(물음표)로 조회가 됩니다.
sqlplus 로 접속해서 보면 한글로 제대로 나오는데 php로 웹상에 보여질때는 한글이 물음표(?)로 나오는데 어떻게 해야 하나요?
인터넷 검색해서 보면 euc-kr 이런 한글 옵션이나 nls 이런 옵션을 맞추면 된다고 하는데 이것저것 해봤는데 안되서 이렇게 글을 올립니다. 오라클 설치시 옵션을 잘못 줘서 그런거지 아니면 php를 설치를 잘못 한건지 정말 모르겠습니다. 고수님들 많은 조언 바랍니다.charater set을 확인해 보세요 5601 또는 949,,,,
949가 디폴트로 알고 있네요 기억이잘;;
글 수정:
user612568 -
Oracle 10g R2 installation on sun solaris 10 Sparc machine
Hi there,
I encountered the following problem during oracle 10g R2 installation on sun solaris 10 Sparc machine
Error encountered:
Using paramFile: /u01/Oracle/10gr2_db_sol/install/oraparam.ini
Checking installer requirements...
Checking operating system version: must be 5.8, 5.9 or 5.10. Actual 5.10
Passed
Checking Temp space: must be greater than 250 MB. Actual 2266 MB Passed
Checking swap space: must be greater than 500 MB. Actual 2335 MB Passed
Checking monitor: must be configured to display at least 256 colors Failed <<<<
>>> Could not execute auto check for display colors using command /usr/openwin/bin/xdpyinfo. Check if the DISPLAY variable is set.
Some requirement checks failed. You must fulfill these requirements before
continuing with the installation,at which time they will be rechecked.
Continue? (y/n) [n]
The following were the steps taken before encountering the above error
1. logged into a workstation
2. From its xterm terminal I logged to the oracle server via ssh oracle@ip
3. keyed in the following at the command prompt
DISPLAY=machine_name:0.0; export DISPLAY
4. executed the following from the command prompt
./runInstaller
Note: when executing the ./runInstaller, the preinstallation checking just hangs at Checking monitor: must be configured to display at least 256 colors. But the log file shows it failed during preinstallation checking as shown in Error encountered
Please help me with this problem.
Thank you
Ravindran KanniahIt is because of UNIX shell. I also faced this error during installation.
First check your shell by the following command.
$ echo $SHELL
Then select the below.
For csh shell
$ setenv DISPLAY 192.168.1.128:0.0
$ export DISPLAY
For sh,ksh and bash
$ DISPLAY=192.168.1.128:0.0
$ export DISPLAY
After you do this check the value of DISPLAY variable.
$ echo $DISPLAY
If the DISPLAY variable is set then run ./runInstaller.
One advice: Keep a complete log of your terminal session. This will help you in future :)
-aijaz -
USER: terminating instance due to error 472 (Oracle 10g)
Hi folks,
We come across a problem that our instance was down suddenly. When checking with the alert log file, it shows that the instance was terminated due to error 472. Did you come across such situation before? Any suggestions would be welcomed.
Following are some information about our Oracle and the log file, trace file.
Oracle Database 10g Release 10.2.0.2.0 - Production
ORACLE_HOME = /app/oracle/lmes
System name: Linux
Node name: lmes-oracle2.ust.hk
Release: 2.4.21-32.ELsmp
Version: #1 SMP Fri Apr 15 21:17:59 EDT 2005
Machine: i686
Alert Log File
Fri Feb 23 09:11:07 2007
Shutting down archive processes
Fri Feb 23 09:11:12 2007
ARCH shutting down
ARC2: Archival stopped
Fri Feb 23 15:16:09 2007
The value (30) of MAXTRANS parameter ignored.
kupprdp: master process DM00 started with pid=32, OS id=1072
to execute - SYS.KUPM$MCP.MAIN('SYS_EXPORT_SCHEMA_01', 'SYSTEM', 'KUPC$C_1_20070223151610', 'KUPC$S_1_20070223151610', 0);
kupprdp: worker process DW01 started with worker id=1, pid=33, OS id=1077
to execute - SYS.KUPW$WORKER.MAIN('SYS_EXPORT_SCHEMA_01', 'SYSTEM');
Fri Feb 23 15:16:28 2007
Thread 1 advanced to log sequence 1309
Current log# 3 seq# 1309 mem# 0: /app/oracle/oradata/elop/redo03.log
Fri Feb 23 15:20:29 2007
The value (30) of MAXTRANS parameter ignored.
kupprdp: master process DM00 started with pid=32, OS id=1526
to execute - SYS.KUPM$MCP.MAIN('SYS_EXPORT_SCHEMA_01', 'SYSTEM', 'KUPC$C_1_20070223152029', 'KUPC$S_1_20070223152029', 0);
kupprdp: worker process DW01 started with worker id=1, pid=33, OS id=1528
to execute - SYS.KUPW$WORKER.MAIN('SYS_EXPORT_SCHEMA_01', 'SYSTEM');
Fri Feb 23 22:15:35 2007
Thread 1 advanced to log sequence 1310
Current log# 1 seq# 1310 mem# 0: /app/oracle/oradata/elop/redo01.log
Fri Feb 23 23:04:10 2007
USER: terminating instance due to error 472
Instance terminated by USER, pid = 7779
Trace File - elop_lgwr_2312.trc
/app/oracle/admin/elop/bdump/elop_lgwr_2312.trc
Oracle Database 10g Release 10.2.0.2.0 - Production
ORACLE_HOME = /app/oracle/lmes
System name: Linux
Node name: lmes-oracle2.ust.hk
Release: 2.4.21-32.ELsmp
Version: #1 SMP Fri Apr 15 21:17:59 EDT 2005
Machine: i686
Instance name: elop
Redo thread mounted by this instance: 1
Oracle process number: 6
Unix process pid: 2312, image: [email protected] (LGWR)
*** SERVICE NAME:() 2007-02-23 09:10:07.372
*** SESSION ID:(331.1) 2007-02-23 09:10:07.372
LGWR: Archivelog for thread 1 sequence 1308 will NOT be compressed
tkcrrsarc: (WARN) Failed to find ARCH for message (message:0x1)
tkcrrpa: (WARN) Failed initial attempt to send ARCH message (message:0x1)
Maximum redo generation record size = 156160 bytes
Maximum redo generation change vector size = 150672 bytes
tkcrrsarc: (WARN) Failed to find ARCH for message (message:0x10)
tkcrrpa: (WARN) Failed initial attempt to send ARCH message (message:0x10)
*** 2007-02-23 15:16:27.116
LGWR: Archivelog for thread 1 sequence 1309 will NOT be compressed
*** 2007-02-23 22:15:35.383
LGWR: Archivelog for thread 1 sequence 1310 will NOT be compressed
Trace File - elop_ora_2336.trc
/app/oracle/admin/elop/udump/elop_ora_2336.trc
Oracle Database 10g Release 10.2.0.2.0 - Production
ORACLE_HOME = /app/oracle/lmes
System name: Linux
Node name: lmes-oracle2.ust.hk
Release: 2.4.21-32.ELsmp
Version: #1 SMP Fri Apr 15 21:17:59 EDT 2005
Machine: i686
Instance name: elop
Redo thread mounted by this instance: 1
Oracle process number: 15
Unix process pid: 2336, image: [email protected]
*** SERVICE NAME:() 2007-02-23 09:10:05.988
*** SESSION ID:(324.3) 2007-02-23 09:10:05.988
Thread 1 checkpoint: logseq 1307, block 2, scn 27684035
cache-low rba: logseq 1307, block 30724
on-disk rba: logseq 1307, block 33205, scn 27699991
start recovery at logseq 1307, block 30724, scn 0
----- Redo read statistics for thread 1 -----
Read rate (ASYNC): 1240Kb in 0.03s => 40.38 Mb/sec
Total physical reads: 4096Kb
Longest record: 21Kb, moves: 0/1975 (0%)
Change moves: 1/24 (4%), moved: 0Mb
Longest LWN: 285Kb, moves: 0/245 (0%), moved: 0Mb
Last redo scn: 0x0000.01a6ab16 (27699990)
----- Recovery Hash Table Statistics ---------
Hash table buckets = 32768
Longest hash chain = 2
Average hash chain = 346/345 = 1.0
Max compares per lookup = 1
Avg compares per lookup = 4783/5281 = 0.9
*** 2007-02-23 09:10:06.132
KCRA: start recovery claims for 346 data blocks
*** 2007-02-23 09:10:07.153
KCRA: blocks processed = 346/346, claimed = 346, eliminated = 0
*** 2007-02-23 09:10:07.154
Recovery of Online Redo Log: Thread 1 Group 1 Seq 1307 Reading mem 0
----- Recovery Hash Table Statistics ---------
Hash table buckets = 32768
Longest hash chain = 2
Average hash chain = 346/345 = 1.0
Max compares per lookup = 2
Avg compares per lookup = 3424/5126 = 0.7
tkcrrsarc: (WARN) Failed to find ARCH for message (message:0x1)
tkcrrpa: (WARN) Failed initial attempt to send ARCH message (message:0x1)
Error in executing triggers on database startup
*** 2007-02-23 09:10:11.557
ksedmp: internal or fatal error
ORA-00604: error occurred at recursive SQL level 1
ORA-12663: Services required by client not available on the server
ORA-36961: Oracle OLAP is not available.
ORA-06512: at "SYS.OLAPIHISTORYRETENTION", line 1
ORA-06512: at line 15
Thanks & Regards,
LionaHi,
I have the same error:
I have gridcontrol 10gR3 installed on VM / Linux 4 AS box. This is second time down time:
finally I found the DB tiers is down.
I have the following message:
Private_strands 18 at log switch
Thread 1 advanced to log sequence 215
Current log# 2 seq# 215 mem# 0: /u02/ora/gridcontrol10g/oradata/emrep/redo02.log
Thu Apr 19 14:30:33 2007
Private_strands 18 at log switch
Thread 1 advanced to log sequence 216
Current log# 3 seq# 216 mem# 0: /u02/ora/gridcontrol10g/oradata/emrep/redo03.log
Thu Apr 19 15:42:34 2007
Private_strands 18 at log switch
Thread 1 advanced to log sequence 217
Current log# 4 seq# 217 mem# 0: /u02/ora/gridcontrol10g/oradata/emrep/redo04.log
Thu Apr 19 16:52:05 2007
LGWR: terminating instance due to error 472
Instance terminated by LGWR, pid = 26049
Thu Apr 19 17:27:08 2007
I have no idea why this happen. is it because DB is ona VM machine?
I remember one time whe I took a snapshot on VM server, grid control services are down for a moment, 4 minutes, WebCache seemed cleaned, this page is gone, after 3 minutes, it comes back.
Anyone has the same issue, please share your experience.
Thanks a lot,
Hank
Message was edited by:
Hank@AHM -
ORA-01722: invalid number error coming in Oracle 10g.
Hi,
We are getting the error "ORA-01722: invalid number" while opening a cursor using CURSOR FOR LOOP.
This error has started coming only after we have migrated to Oracle 10g from Oracle 9i. Earlier the same code used to work properly. And also on Oracle 10g, its not happening every time. Sometimes it gives error while sometimes it works.
Does anybody know about any such bug in Oracle 10g. Our cursor is a parametrized cursor accepting a VARCHAR2 parameter and the value we are passing to it is also character.
Our database is Oracle 10g Enterprise Edition Release 10.2.0.3.0 - 64bit Production and is running on UNIX server.And also on Oracle 10g, its not happening every time. Sometimes it gives error while sometimes it works. This is typically due to
a) environment settings that differ from session to session
b) or more often, data
The actual error means that Oracle expects a number and is unable to obtain a number from the input (data or SQL or bind variables) supplied. I agree with William that it looks a lot like an implicit TO_NUMBER() conversion failing.
Why not add a debug exception handler to the code? When that exception occurs, dump the PL/SQL call stack and values of all variables and parameters to a debug/logging table (using an autonomous transaction). -
Error while installing Oracle 10G on Oracle Enterprise Linux 4.8 32 bit
Our machine is a x86_64 machine with 32 GB of RAM available. I have installed OEL 4.8 32 bit on this machine (configured swap space of 32 GB) and OEL by default boots with the Hugemem kernel.
I am trying to install Oracle 10G enterprise edition on this. All required kernel parameters, shell limits etc. have been verified and configured. The preinstallation checks succeed on all the tests and installation proceeds smoothly. However in the last step of configuring the database using dbca following two errors are thrown:
1. ORA-27102 - out of memory
2. ORA-01034 - ORACLE not found
Most places where I am reading are telling to configure kernel parameters. However that doesn't seem to be the problem in this case.
Please Help.Hi;
What is exact db version? What installation log says?
Please see and confirm you have all pre-req settings
Oracle Database on Unix AIX,HP-UX,Linux,Mac OS X,Solaris,Tru64 Unix Operating Systems Installation and Configuration Requirements Quick Reference (8.0.5 to 11.2) [ID 169706.1]
Regard
Helios -
Error while installing Oracle 10g on Solaris 9 x86
Hi all,
I got several error after install oracle 10g. After I run the root.sh. It prompt :
Starting Oracle CSS service under init(1M)
Expecting the CRS daemons to be up within 120 seconds.
Giving up: Oracle CSS stack appears NOT to be running.
and when I start sqlplus, it prompt:
ERROR:
ORA-01034: ORACLE not available
ORA-27101: shared memory realm does not exist
Intel SVR4 UNIX Error: 2: No such file or directory
and following the error message prompt every minutes.
"oracle: (Oracle CSSD will be run out of init)"
"root: Failure in CSS initialization opening OCR."
I don't think reinstall oracle will solve my problem if I don't figure out what going wrong. Could anyone tell me what I need to do? Thanks very much for helping.
Cheers,
AlexCheck also if the t-bit is set:
[root@vtl1g121 ~]# ls -dl /tmp
drwxrwxrwt 11 root root 4096 Apr 10 11:44 /tmp
This is needed to mark the filesystem/directory as temporary.
Sometimes this can cause such problems also
Command: chmod +t /tmp -
Error while installing oracle 10g on centos 5.6 32 Bit
Hi All,
Please help me with the issue I facing while installing oracle 10g on centos 5.6 32bit. I did lot of research on google but I am getting same answer...the libXp package is missing, but I have check it...its already installed.
[root@staging ~]# find / -name libXp.so.6
/usr/lib/libXp.so.6
/usr/lib64/libXp.so.6
echo $DISPLAY
<ipaddress>:0.0
[oracle@staging database]$ DISPLAY=<ipaddress>:0.0; export DISPLAY
[oracle@staging database]$ id
uid=500(oracle) gid=500(oinstall) groups=500(oinstall),501(dba) context=root:system_r:unconfined_t:SystemLow-SystemHigh
Below is the error message I am getting :
oracle@staging database]$ ./runInstaller
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2012-06-27_05-37-17PM. Please wait ...[oracle@staging database]$ Exception in thread "main" java.lang.UnsatisfiedLinkError: /tmp/OraInstall2012-06-27_05-37-17PM/jre/1.4.2/lib/i386/libawt.so: libXtst.so.6: cannot open shared object file: No such file or directory
at java.lang.ClassLoader$NativeLibrary.load(Native Method)
at java.lang.ClassLoader.loadLibrary0(Unknown Source)
at java.lang.ClassLoader.loadLibrary(Unknown Source)
at java.lang.Runtime.loadLibrary0(Unknown Source)
at java.lang.System.loadLibrary(Unknown Source)
at sun.security.action.LoadLibraryAction.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at sun.awt.NativeLibLoader.loadLibraries(Unknown Source)
at sun.awt.DebugHelper.<clinit>(Unknown Source)
at java.awt.Component.<clinit>(Unknown Source)
I found some suggestion on google and tried to not use ip address in DISPLAY settings...
if I am using 0.0 instead of IP below eg.
[oracle@staging database]$ DISPLAY=:0.0; export DISPLAY
The error I am receiving differnt error
[oracle@staging database]$ ./runInstaller
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2012-06-27_05-34-40PM. Please wait ...
DISPLAY not set. Please set the DISPLAY and try again.
Depending on the Unix Shell, you can use one of the following commands as examples to set the DISPLAY environment variable:
- For csh: % setenv DISPLAY 192.168.1.128:0.0
- For sh, ksh and bash: $ DISPLAY=192.168.1.128:0.0; export DISPLAY
Use the following command to see what shell is being used:
echo $SHELL
Use the following command to view the current DISPLAY environment variable setting:
echo $DISPLAY
- Make sure that client users are authorized to connect to the X Server.
To enable client users to access the X Server, open an xterm, dtterm or xconsole as the user that started the session and type the following command:
% xhost +
To test that the DISPLAY environment variable is set correctly, run a X11 based program that comes with the native operating system such as 'xclock':
% <full path to xclock.. see below>
If you are not able to run xclock successfully, please refer to your PC-X Server or OS vendor for further assistance.
Typical path for xclock: /usr/X11R6/bin/xclock
[oracle@staging database]$ echo $SHELL
/bin/bash
Please help me.satish.ygl wrote:
Hi,
I am getting the same error when i am applying patchset to 10201 to 10204. I am using RedHat Linux 4 version and I tried set $DISPLAY=<hostname/ip address>:0.0 and export=DISPLAY
#xhost + and checked $PATH this is also is correct
I did these steps still i am getting the following error
pen an xterm, dtterm or xconsole as the user that started the session and type the following command:
% xhost +
To test that the DISPLAY environment variable is set correctly, run a X11 based program that comes with the native operating system such as 'xclock':
% <full path to xclock... see below>
If you are not able to run xclock successfully, please refer to your PC-X Server or OS vendor for further assistance.
Typical path for 'xclock': '/usr/X11R6/bin/xclock'
Please help me in this scenario.
thank You,
Sri
Edited by: satish.ygl on Oct 30, 2012 7:49 PMyou must log onto the DB Server as below (or functional equivalent)
ssh -X oracle@DB_Server
& the first & only command after logging onto the DB Server should be as below
xclock
If/when xclock fails, then OUI will fail.
Maybe you are looking for
-
Loud noise when iSight launches from iMovie
Hi everyone, I just bought a MacBook Pro and when I launch iMovie and slide the little button (scissors to movie camera) to turn on the iSight my MBP makes a loud (EEEEEHHHHHH) sound. When it happens it sounds like my speakers are going to blow. It l
-
HT2498 i followed all the steps and my canon camera still wont come up
i updated the mac soft wear and updated the iphoto and when i conect my camera it stll doesnt come up
-
Older mac OS compatability with versions of elements and photoshop
Hello. Is there a nice easy to read table out there to list this? I did find one for Elements but only deals with versions of OSX. Thanks. PCguy
-
New host, same LS and Portal on same DB
All, We moved the WebServer to a new host, the Portal and Login Server schemas are the same and on the same DB.Do I just run ssodatax ? Thanks Sanjay
-
hi, I have problem in JavaRE in browser..... I reinstall java package, but on ibm-site I dont find: - ibm-java2-sdk-50-linux-ppc.tgz but instead : - IBMJava2-SDK-1.4.2-9.0.ppc.tgz is this file OK ? thankyou