Oracle connecting with one system

Hi all,
We have Oracle (10.2.0.1) on windows 2003.
Oracle Server IP->192.168.4.19
My system IP->192.168.4.108
Now i want that only my system(192.168.4.108) is enable to connect to Oracle Server.Connection from another IP is denied.
How can i implement this configuration?
Please Guide
thanks,
Neerav

Neerav999 wrote:
Gk Joe could please me understand "valid node checking"Learning where to look things up in the documentation is time well spent investing in your career. To that end, you should drop everything else you are doing and do the following:
Go to tahiti.oracle.com. Drill down to your product and version.
Spend a few minutes just getting familiar with what is available here. Take special note of the "books" and "search" tabs. Under the "books" tab you will find the complete documentation library. <b>Look under the 'search' tab for 'VALID_NODE'. </b>
Spend a few minutes just getting familiar with what kind of documentation is available there by simply browsing the titles under the "Books" tab.
Open the Reference Manual and spend a few minutes looking through the table of contents to get familiar with what kind of information is available there.
Do the same with the SQL Reference Manual.
Do the same with the Utilities manual.
You don't have to read the above in depth. They are reference manuals. Just get familiar with what is there to be referenced. Ninety percent of the questions asked on this forum can be answered in less than 5 minutes by simply searching one of the above manuals.
Then set yourself a plan to dig deeper.
- Read a chapter a day from the Concepts Manual.
- Take a look in your alert log. One of the first things listed at startup is the initialization parms with non-default values. Read up on each one of them in the Reference Manual.
- Take a look at your listener.ora, tnsnames.ora, and sqlnet.ora files. Go to the Network Administrators manual and read up on everything you see in those files.
- When you have finished reading the Concepts Manual, do it again.

Similar Messages

  • How many apple tv can I connect with one account?

    how many apple tv can I connect with one account?

    there are 2 recent posts that suggest issues over 5, one where someone was trying to troubleshoot for a friend or client as they couldn't keep more than 5 connected, and the other where somone had more than 5 but was using 2 separate itunes libraries to share the load - not sure if that was with the same or differing AppleIDs.
    I guess there is always the possibility that things kight vary from one itunes version to the next even unintentionally to allow more.
    AC

  • How to verify the  Source systems connectivity with BWQ System.

    Hi All,
    I have diff source systems. And my requirement is to check the source systems connectivity with BWQ (BW Quality sys). please any body tell me the steps how to check the source system connectivity ?
    Thanks & Regards,
    Manju

    Hi Manjula,
    If you encounter problems when establishing a connection to your target server, check the following:
    A message box appears while performing one of the following actions:
          Setting connection by choosing Apply to local session.
          Testing connection settings by choosing Test settings.
          Creating SAP TSQL objects
    If errors occurred, they are displayed in the respective message box.
       Check developer trace files in ST11.
      Test connection:
         For RFC related errors, check the RFC connection via SM59
         For database multi-connect errors, check if you can connect to the target SQL Server with the SQL Server Query Analyzer. Also check if the DBCON entries are correct.
    Regards,
    RK

  • DB Connect WITH BI System

    Dear Experts,
    I have to connect my BI System with Microsoft Sql Server.
    I have read so many standard documents but still not sure how to proceed with it.
    My First conern is related to DBSL Library .  From where we can downlaod and which file need to be download and where to kept it. ?
    Second Concern is user id and password of database. is it necessary same user should exist in both system.(BI System and SQL Server)  ?
    Third concern :  Is there any Specific settings need to activated in SQL Server ?
    Please help me as I am not getting exact answer from standard documentation available.
    Regards,
    Mohit.

    Hi there,
    Dont' know in BI 7.0 and oracle but I did it once with SQL Server and BI 3.5.
    There, tables shown are database views that have been created whit certain conditions like:
    User on the connection parameters is bd_owner of the database views.
    User have select permisions for the database views
    User have db_dladmin
    Check requirements for oracle but it seems and autorization problem on the database side.
    Hope this helps,
    Regards,
    Carlos.

  • Sap Oracle Connection with other oracle

    Dear Experts ,
    I am trying to connect other oracle machine through database enterned necessary entries in TNS and listerner ora , but i not able to connect
    oracle veriosn is 9.2  and on sap server oracle  is  10.2  , is there any prblm with  version
    Please advise

    Hi Fidel.
    My requirement is i want  to connect to other oracle database with my sapsystem oracle database .
    i am trying to connect thru SQL prompt .i am able to ping the Ip of system , TNSping is also working .
    had made entries in TNS and lister.
    but  when i am trying to connect from SQL  iam  getting error
    ORA-12170: TNS:Connect timeout occurred
    please advice
    Thanks and regards

  • Oracle Connectivity with MS SQL Server. ORA-00972: identifier is too long

    I have linked Oracle Database with MS SQL Server using HS and DB Link.
    DB Link Script:
    CREATE DATABASE LINK "FCHH"
    CONNECT TO SA
    IDENTIFIED BY <PWD>
    USING 'LISTENER_FCHH';
    Links tested successfully.
    Now "SA" user in Microsoft SQL Server has multiple databases i.e. Master,SecurePerfect,SecurePerfectHistory. when I try following command
    select * from "SecurePerfectHistory.DBO.BadgeHistoryTable"@FCHH
    ORA-00972: identifier is too long

    ORA-00972: identifier is too long
    Cause: An identifier with more than 30 characters was specified.
    Action: Specify at most 30 charactersAman....

  • Broadband connection with one static ip

    Hello Everyone!!
    I would like to seek your kind suggestion in mapping static ip address to the local ip address.
    We have a bsnl broadband connection, and bsnl has provided us with one static ip address.
    We are using  broadband modem.
    Now I would liket to map this static ip address to one of the private ip address which is 192.168.1.2(database server).
    i want to do nat above ips if i do so then i dont have no ip to assign to my outside interface.
    I would like to access this device over internet, by typing my public (Static ip ) given by the BSNL.
    Kindly let me know how should i configure this modem.
    security device i have is cisco ASA 5505.
    Need suggestion.
    thanks in advance

    Hi,
    I am afraid that if you are asking for guide to configuring your broadband modem then this is probably not the best section of the Cisco Support Community to do that.
    Generall though it would be best if the modem you have was configured as Bridged device and the public IP address was configured on the ASA5505 directly on its "outside" interface. This saves you from a lot of trouble playing with possible NAT configurations on 2 devices.
    On the ASA5505 you will basicly be configuring Static PAT and NOT Static NAT.
    Static NAT would bind the public IP address to the use of only single internal host.
    Static PAT on the other hand would bind certain TCP/UDP ports to some internal host.
    So naturally we should first determine which ports you need to forward to the internal host and also what the software level of your ASA5505 is so we know which NAT configuration format to use (version number is shown with the command "show version" or in the  main view of the ASDM)
    NAT/ACL 8.2 (and older) Configuration format
    static (inside,outside) tcp interface 80 192.168.1.2 80 netmask 255.255.255.255
    access-list OUTSIDE-IN permit tcp any interface outside eq 80
    access-group OUTSIDE-IN in interface outside
    In the above configuration we first use the "static" command to configure the Static PAT. The configuration basicly states that we want to forward the TCP/80 port using the "outside" "interface" IP address to the local IP address of 192.168.1.2 and local port of TCP/80.
    Finally we make an ACL that allows TCP/80 traffic from anywhere and we attach the ACL to the "outside" interface with "access-group" command. If there is an existing ACL attached to the "outside" interface then you would naturally use that.
    NAT/ACL 8.3 (and newer) Configuration Format
    object network SERVER-WWW
    host 192.168.1.2
    nat (inside,outside) static interface service tcp 80 80
    access-list OUTSIDE-IN permit tcp any object SERVER-WWW eq 80
    access-group OUTSIDE-IN in interface outside
    The above basicly does the same as the first example with the older ASA software. There are just noticiable changes in the NAT and ACL configuration formats.
    Hope this helps
    - Jouni

  • How to get audio device information connected with MAC system?

    I want to know the samplerate (the number of samples per second) supported by the device connected with the MAC system.
    I am also pasting the code as below where I need that info.
    // Using PCM 44.1 kHz, 16 bit signed,stereo.
              AudioFormat audioFormat = new AudioFormat(AudioFormat.Encoding.PCM_SIGNED,  //     the audio encoding technique
              44100.0F,// sampleRate           the number of samples per second
              16,      // sampleSizeInBits the number of bits in each sample
              2,       // channels           the number of channels (1 for mono, 2 for stereo, and so on)
              4,       // frameSize           the number of bytes in each frame
              44100.0F,// frameRate          the number of frames per second
              false);  // bigEndian          indicates whether the data for a single sample is stored in big-endian byte order (<code>false</code> means little-endian)

    Kanni wrote:
    Can you sugget something in that area.That's not an issue that's specific to MAC, it'd be specific to any system with a limited number of supported capture formats.
    I've handled this problem in the past by generating an array full of all of the AudioFormat objects I'd consider acceptable, and I just iterate through them until I can find a TargetDataline that supports it.
    TargetDataLine tdl = null;
    /* Write your own code to get an array of acceptable formats here */
    AudioFormat formats[] = JavaSoundFormats.getFormatList();
    for (AudioFormat format : formats) {
        DataLine.Info dlinfo = new DataLine.Info(TargetDataLine.class,
                                                 format);
            if (AudioSystem.isLineSupported(dlinfo)) {
                try {
                    audio_in_format = format;
                    tdl = (TargetDataLine)AudioSystem.getLine(dlinfo);
                    break;
                catch(LineUnavailableException e) {
                    // No need to do anything
    /* If we don't have a targetdataoutput object, give up */
    if (tdl == null) {
        System.err.println("No TargetDataLines found!");
        System.exit(1);
    }

  • How to install two oracle database on one system

    i want to install two oracle databases on single system how it is possible
    how i can manager oracle home and is this possible to install two different version of oracle in single home or single system forexample oracle 9 and oracle 8 .
    A.R

    Hi,
    yes, u can have more databases on a single machine and they can be of different versions.
    You have to use and initialize the correct ORACLE_HOME to create the DB of the version U use.
    For ex, u have 2 homes:
    C:\Oracle\Ora817 8i home and C:\Oracle\ora920 9i home
    Normally, using OFA, imagine that You want create 2 db, TEST_8I for 8i home and TEST_9I for the 9i home, You shold have:
    C:\Oracle\Admin\TEST_8I\<<OFA DIRS>> and C:\Oracle\Oradata\TEST_8I for 8i DB adn C:\Oracle\Admin\TEST_9I\<<OFA DIRS>> and C:\Oracle\Oradata\TEST_9I for the 9i version.
    It is important, when You create the DB, that u use the executables of C:\Oracle\Ora817\bin to create 8i db and C:\Oracle\Ora920\bin for the 9i one.
    Then U can use the 9i listener to manage both instances
    Hope this helps
    Max

  • Bussiness Objects connection with R3 systems

    Hi,
    I would like to connect Bussiness Objects with R3 systems, does anyone have a tutorial or refer any note?
    Best Regards,
    Nuno Silva

    Dennis is right, the connectivity option youo have today is limited to Crystal (unless you wanted to do something purely at the DB layer), but Webi/Universes for ERP are coming in a future release.  A prototype is availble at the Innovation Center
    SAP BusinessObjects Web Intelligence Reporting for SAP ERP [original link is broken]
    Very weird.  I only posted this once, but two posts appear??????
    Edited by: Pizzaman on Oct 1, 2009 10:57 AM

  • IPhone with iOS 7.1.2 cannot connect with car system

    Hi,
    I am using iPhone 4s with iOS 7.1.2 . I used to connect it with my car (fiat bravo, with blue&me system) and it has worked well, but it was still on iOS 7.1.1. Now it doesn't want to connect with the car, phone sees the car, but cannot connect with it. How can I solve this?

    Hello, Brunon_Wayward. 
    Thank you for visiting Apple Support Communities.
    Sometimes when an iOS update is released there is a compatibility lag with certain features that requires an update to the vehicle.  I would first check with your vehicle manufacture for any firmware updates.  However, here is an article that has some helpful troubleshooting steps regarding car stereo connections and an iOS device.
    iOS: Troubleshooting car stereo connections
    http://support.apple.com/kb/ts3581
    Cheers,
    Jason H.

  • Why does facetime hang up when i connect with one certain person

    help me!!!!!!!

    That would not be an OS X or iMac issue if the problem is only with one other person. That points the finger at an Internet connection issue that must be solved by an ISP, my guess is the other person has a slow or problem Internet connection that needs troubleshooting.

  • Multiple oracle session with one select

    Hi,
    When i run simple select statment oracle OPENS 5 different sessions and each session run same select .
    any body know what is wrong with it ,is there any parameter problem.
    HERE is a programe :
    ORACLE.EXE (P000)
    ORACLE.EXE (P001)
    ORACLE.EXE (P002)
    ORACLE.EXE (P003)
    ORACLE.EXE (P004)

    Basically my problem is that i am running an INSERT statement based on a SELECT statement on different tables.
    Now the problem is at times Oracle stops responding and my application hangs.
    I cannot find any other clue than the parrallel execution of INSERT statement by ORACLE.
    The reason i am considering this as an issue is when i check the status of my table on which i am running INSERT statement, they are locked.
    Below is sample peusdocode of my task.
    For each file
    begin
    open oracle connection
    read data from file using sql loader;
    insert into my tables based on select; ///// here after reading 1 or 2 files oracle hangs
    close oracle connection;
    end

  • Bandwidth problem connecting with one person on my buddy list

    I'm connected to the web via cable modem, which is connected to an Apple Extreme Base Station. I was able to video chat with my brother-in-law in LA who is connecting via DSL. Recently we can't video chat. Nothing seems to have been changed in either of our settings and we can both connect with others that we share in common in our Buddy list.
    All we get now is the Not enough Bandwidth error. Any ideas why this is happening?

    Error 22 will be the Quicktime setting, the Bandwidth setting in iChat or something the ISP is doing top the Connection speed.
    Reinstalling Leopard for just that is not likely to change anything.
    7:11 PM Saturday; January 12, 2008

  • IPhone connectivity with a system

    Please, how do I share my Apple iPhone4 internet connection with a computer........Thank you

    http://support.apple.com/kb/HT4517

Maybe you are looking for