Orange LED on power adapter won't turn green after 10.4.7 update?

Hey guys,
this could be independent of the 10.4.7 update, but I've noticed that after the update, the LED does not turn green. The battery seems to charge fully, but the icon says, (Calculating...) and the LED stays orange. (left it like this for a whole night)
So far I've tried to reset the PMU and repaired permissions with no luck. Currently I'm calibrating the battery but I'm wondering whether anyone has had similar issues and whether anyone has a fix for it. Thanks in advance.

Hey there. Have you had any other issues with your battery, ie. not able to fully charge, or shutdowns before the OS tells you power is getting low?
The reason I ask (not to scare you) but this inability for the charger to turn green was the first symptom I saw when my MacBook Pro battery was in the process of dying. It happened about two weeks before things went south for this battery. As you may have read on this board, there was a run of batteries for these machines that have shown some serious problems. Ultimately what happened with mine was that it would get down to about 34% charge, and then the machine would just turn off. The battery also would often not charge all the way up to the green indicator, either.
I am unsure of what else you can try, other than maybe resetting PRAM. Just be on the watch for increased battery flakiness over the next couple of weeks. Not to worry, Apple will replace the battery for you free of charge.

Similar Messages

  • My Ipad air won't turn on after the new IOS7 update

    my Ipad Air won't turn on after updating to the new IOS 7.1.1. It ask me for my password I put it in, the apple logo appear and then it want off now it won't come back on. need help please

    Did you try this?
    Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

  • 5s won't turn on after 7.0.5 update

    Saw the update today
    Downloaded the update and plugged phone to a main power source
    Started to install the update, then nothing. No power, can't restart the phone and need I'm a few hour for work.
    Any help is welcomed.

    Hi there Jatinos,
    You may find the troubleshooting steps in the article below helpful.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Issue not resolved
    My issue is still not resolved. What do I do next?
    Contact Apple Support.
    -Griff W. 

  • My iPod touch 5th generation won't turn on after the new iOS update

    I've just updated my iPod touch 5th generation to the iOS 8.1.1. (or whatever the newest update is) but once it updated, it now won't turn back on. I've tried plugging it into multiple chargers and computers just in case it wasn't charged, and tired turning it on, but all I get is the apple logo and nothing's happening. What can I do? I haven't backed it up this month and I don't want to loose all my stuff. Thanks.

    Try the following. It is very likely that the iPod will have to be erased:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     
    In the future make sure yo backup before updating. I always backup to both iTunes and iCloud before updating .

  • My Ipad air won't turn on after restarting during an update

    It stopped turning on after I reset midway through an update because the update froze. As in, it stopped completely for four hours.

    Did you try this?
    Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

  • MacBook Pro 15" 2007 won't turn on after leaving Snow Leopard update in the drive

    Hi Everyone,
    After installing Snow Leopard 10.6.3, I left the cd in the drive when I turned the computer off. When I tried to turn the computer back on again, the screen told me that I needed to restart the computer by holding down on the power button. So I did, but the message came up again. I did it again. The third time, the computer wouldn't turn on at all.
    I removed the cd by opening up my computer--something I had done in the past because of problems with the keyboard. (The keyboard was never fixed, and the trackpad didn't work either, so I used USB connections.The powerbutton never was affected though)
    Two questions:
    First, what would you say is the culprit in the first problem with the messages to restart the computer? How might I address this?
    Second, knowing the secondary information about the keyboard connections, how might this affect fixing the problem? Could the powerbutton now be affected, especially since I lifted the keyboard off?
    Lastly, I've looked into restarting the SMC, and turning on the computer without the button. I have tried the first of these two options, and will soon attempt the second (If anyone can send me a link to better explain turning on the computer without a button for my model, I'd be grateful.)
    Any more advice (short of bringing it into the shop!) would be helpful.

    Try powering up and push in your install disc(use your original install disk if you have it, maybe try the retail SL disc white with the cat as a second choice) holding the C key (this should make it boot from the disc) select your language, click continue, in the next screen in the menu bar click Utilities/Disk utilities, select (highlight your volume from the left column, default name is Macintosh HD, unless you renamed it) click the first aid tab, then click verify disk, if it comes up with errors (they will be in red font) if you get errors, run repair disk, run it repeatedly if necessary till it comes up with this disk seems ok (in green font)
    Then run permissions repair.
    Log out and reboot see what you get.
    You may have to reinstall the 10.6.3 OSX again, do this by powering up and pushing in the disk holding the C key and follow the prompts. if you have a successful install, eject the disc, and reboot. The next thing you need to do is run software update, there will be many and you want to do them one at a time. (use an ethernet connection as opposed to wireless, as there is much chance of corruptions. The first one to run is the 10.6.8 combined v 1.1, the keep running software update one at a time till there are none offered.
    Hope this helps

  • IPad won't turn on after I tried to update it.

    Hey. So I tried to update my iPad to 7.0.6 I think but it said there was an error and now my iPad screen is stuck on the iTunes Logo and the cable. I've tried turning it off by holding down the lock button and the home button but when it turned back on, it was the same screen and iTunes won't recognise my iPad. Help please!

    Your iPad is in Recovery Mode.
    Follow the instructions here carefully:
    http://support.apple.com/kb/ht1808

  • IPhone 3G Won't Turn On After OS 4.0 Update

    A little background about my iPhone 3G to help you guys out -- the sleep/wake button hasn't worked in a few months, so if, say, Safari freezes, I let the battery die out to restart my phone. A major pain, I know.
    Tonight I decided to update through iTunes to the OS 4.0. It seemed as if everything was going well, but after about an hour of backing up and installing, my phone is now permanently turned off seeming to have never restarted from the update. To make matters worse, it is no longer recognized by iTunes or my PC. As stated, the sleep/wake button doesn't work so a hard reset or restore is physically impossible. Does anyone have suggestions on how to restore the phone back to the previous OS?
    I'm currently trying to reinstall iTunes as I type this.

    After several hours of various numerical error messages, freezing loop, iTunes not recognizing the 3G, rebooting the computer (iMac), hard resets, etc, I forced it off and went to bed. Today I found that while iTunes still would not recognize the phone as it would normally, it did when I unplugged and then plugged in the phone. The phone was then restored ( 4.0 was obviously installed last night and then went into a loop). I refused backup, restored OS, but did not continue to restore from back up. The phone is now operational and synced via mobile me, however no apps than system. Based on the latter I will not allow iTunes to restore my backup until this problem is resolved. Some of the said apps are used for business, but I have the iPad to sync them with in the interi.

  • Auto-brightness Won't Turn off after Win 8.1 update

    I have a Y510P, and I got the Win 8.1 update about a month ago. Since then, my screen auto-dims whenever the average color of the screen is darker than plain white. So every time I am on a website that has a picture (like Facebook), as soon as I scroll to it, my entire screen dims. Also, I cannot watch videos without my laptop being plugged in because the screen is too dark to watch it on.
    When my laptop is plugged in, I have no issues. Also, even after the brightness is decreased, it tells me that my brightness is turned up all the way.
    I went into the advanced settings in control panel and have auto-brightness disabled, but it isn't helping. I tried accessing the NDIVIA settings to see if it's in there, but all I can access are simple controls, none of which affect brightness.
    Is there anything I can do to fix this? 

    this happened to me aswell please help

  • IPhone won't turn on after attempting iOS 5 update?

    Hi! So, I was trying to update my iPhone 4, but after everything had finished downloading and backing up, the "SIM card is not supported" message came up, so I turned my phone off, and tried to turn it on again, but it wouldn't. I tried to do that home button + lock button thing, but even that isn't working. My phone isn't jailbroken or unlocked as far as I know, but it was an Apple store replacement after my last one started having problems. My phone has never shown any problems before and my last update was complete fine.

    I had same issue with replacement iPhone 4 and got it replaced last week.  Tried update tonight and same issue sim card not supported!!  Apple guys at store had no idea and told me to go to ATT to get new sim card but I said no let's test sim card here.  We did and sim card was fine.  We then tried his sim card on my phone and it was not recognized!  Do the same to get new phone but don't update iOS 5.  Until they fix it.  I heard it's a bad bunch of replacement phones with serial code issues which is exposed after update. Good luck!

  • My power cord will not turn green, what can I do

    My power cord will not turn green after preforming an update, what can I do

    http://support.apple.com/kb/TS1713

  • Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Switched from DSL to cable modem. My Airport light won't turn green. Keeps blinking orange. No wireless now and can't connect to more than one computer! ?????

    Hmmmm.
    If you reset the AirPort Extreme by holding in the reset button for 9-10 seconds and then releasing, the AirPort should be back in default settings which would allow mutliple computers to connect to the LAN ports on the AirPort.
    Power off the cable modem for now and leave it off at least 15 minutes.
    With the AirPort Extreme still powered on, hold in the rest button on the back for 9-10 seconds and release. Allow a full minute for the AirPort Extreme to restart to a slow, blinking abmer light.
    Then, power off the AirPort Extreme.
    Check to make sure that the Ethernet cable from the modem is connected to the WAN "O" port on the AirPort Extreme.
    After the modem has been powered off for at least 15 minutes, power it up and let it run for 5 minutes by itself.
    Now, power up the AirPort Exteme and let it run for 2-3 minutes
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Connect an Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Express
    Click on the AirPort Exteme, then click Continue to follow the guided setup tp configure the AirPort Extreme.  You can use the same wireless network name, password, etc that you used before, or set up a new name and password, etc.

  • What to do now when my iPad won't turn on after I turn it off. It shows only the apple logo. I am sure it has above 70% charge as when I sync my iPad it shows necessary detail in iTunes. I have tried, HOME & POWER button, but did not work.

    What to do now when my iPad won't turn on after I turn it off. It shows only the apple logo. I am sure it has above 70% charge as when I sync my iPad it shows necessary detail in iTunes. I have tried, HOME & POWER button, but did not work.

    First try a Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
    If no joy... Try a Restore...
    1: Connect the device to Your computer and open iTunes.
    2: If the device appears in iTunes, select and click Restore on the Summary pane.
    Restoring  >  http://support.apple.com/kb/HT1414
    Make sure you have the Current Version of iTunes Installed on your computer
    iTunes free download from www.itunes.com/download
    3: If Unable to Restore, try using the Steps in this article to force the device into Recovery Mode.
    Note on Recovery Mode.
    You may need to try this More than Once... Be sure to Follow ALL the Steps...
    After you have Recovered your Device...
    Re-Sync your Content or Restore from the most Recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766

  • LaserWriter Pro 630 two solid orange lights won't turn green.  Put in new toner and test page does print.  Any ideas?

    LaserWriter Pro 630 two solid orange lights won't turn green.  Put in new toner and test page does print.  Any ideas?
    The warmup stage does not seem to go all the way through its normal startup noises and the printer does not get hot.
    Thanks for any help.
    Steve

    See if this link has some useful info:
    LaserWriter Pro 600/630

  • Hello, My white McBook (2008 or 2009) recently stopped turning on.  When I hook up the Magsafe power adapter, the light shows green, but the computer will not turn on, or make a sound.  I've tried the re-boot option, but nothing works.  Please advise!

    Hello,
    My white McBook (2008 or 2009) recently stopped turning on.  When I hook up the Magsafe power adapter, the light shows green, but the computer will not turn on, or make a sound.  I've tried the re-boot option, but nothing works.  I first thought I needed a new battery because the lights at the back are all off, but shouldn't the computer turn on once the power adapter is hooked up and the light on the Magsafe adapter shows green?  I'm a computer doofus, so please be kind.  Please advise!  Thanks in advance.
    SS

    Take it in for service.

Maybe you are looking for