Original Airport Card Firmware Update?

I have been trying to update the firmware on my airport original card. Even though I installed the 4.2 update via panther, I still found the firmware to be the same. Is this wrong? It says the airport card firmware is 8.7 something. I think the latest wpa compliant version for the airport original is 9. something. I can't seem to figure out why this didn't work. (P.S. I realize this is supposed to be for airport extreme cards, but I can't seem to find out where to post this.)

If you have installed all of the updates available in Software Update the firmware is up to date.
If your Mac has OS 10.3 or beyond, it has the ability to connect to a WPA protected network.

Similar Messages

Update--original Airport card w/ no signal

I have now been able to swap original Airport cards with a clamshell iBook and have determined that the "no signal" issue is with the PowerBook G4 Titanium 500 mHz or possibly the OS X 10.4.7 upgrade.
I had previously tried a Linksys 802.11b PCMCIA card and a D-Link 802.11b PCMCIA card in this PowerBook and had exactly the same symptoms--the card was recognized by the operating system, but no wi-fi signal was detected. I read some posts in this forum about PCMCIA card firmware version incompatibilities with OS X and wi-fi connectivity issues with PCMCIA cards after installing OS X 10.4.7, so I decided buying an original Airport card was best solution, and then found out that it doesn't work either!
Now I would like to find out if anyone has suggestions for resolving whatever issue I'm encountering. As I said in my earlier post, I've tried reseating the card and connector as well as unplugging and replugging the antenna connector. I've also tried pressing on the side of the battery compartment where the antennna is located. I haven't tried pulling the antenna out (don't know how difficult that is), but it's not visibly damaged. Probably not a related problem, but the DVD player doesn't work--it attempts to mount a disc but always fails.
Replacing the antenna might be an option; on the other hand, the PCMCIA cards didn't use the Airport antenna and they didn't work either, so I definitely wonder about a software issue.
When I got this machine I reformatted the HD, installed Tiger, and promptly installed all the updates through 10.4.7 before trying to set up wi-fi connectivity, so I don't actually know what effect the updates may have had.

Replacing the antenna might be an option; on the other hand, the PCMCIA cards didn't use the Airport antenna and they didn't work either...
Right — so it definitely isn't an antenna issue.
Is it possible that the network you're trying to connnect to is hidden? I know just barely enough about wireless networking to be dangerous, but I remember when I was setting my router up originally a couple of years ago, there was some option to cloak the network so it wouldn't be visible at all to unauthorized machines, or something like that. It was one of many security features, and I didn't opt to to use it because my router is several hundred feet from any road or other building and requires a password; I don't worry about anyone getting into my network without my knowedge.

How does one update original airport card for WPA?

Hi, I've an earlier AX, and an original airport card that I understand can be updated to be able to be WPA compatible. How do I do this? The AX is setup for WPA/WPA2 personal, and I have no trouble joining the network from other macs, and I just learned that the original airport card is supposedly able to be updated to also handle WPA. This card is installed on a g3 imac 700 se with os 10.4.11.
I also posted this question in the airport express forum, but thought it may have a better chance of being answered here after I thought about it a bit.
Thank you,
ez

You can't get it to do WPA2.
You can get it to do WPA if you have the right software installed, which you probably already do:
AirPort Card: When You Can Join a WPA Network
The base station or equivalent has to be set up for 802.11b/g that is BOTH b and g, since the \[original] Airport card is 802.11b.

Two versions of original Airport card?

I have only today learned that the original Airport card came in two versions: 661-2219, which does not have the capability of accessing a WPA-protected router, and 661-2549, which does. My question is, how do you distinguish between these two cards, visibly or otherwise?

It was not 'suddenly discovered,' as we have made this claim for many years. I don't understand how it is inconsistent with what you insist to be the case, as…
• we refer only to the A/B revisions—which you agree do not support WEP beyond 40 bits—to be incapable of supporting WPA, as they shipped from the factory
• we sell such cards with the lower level of capability for use in pre-OS X 10.3 installations with the clear caveat that such cards, as sold, don't support WPA or—if you will—are not guaranteed to, and should be expected to, support WPA
It's not in our financial interest to apply firmware to the older cards which we periodically encounter and we don't claim that it has been done, as we don't test each card specifically for such capabilities. Why bother to, when they are sold indicating that they do not support WPA? We don't speak for others in the industry, only for ourselves. And, we attempt to convey simple, accurate information. In this case, we think we achieve that in a way that lowers what might otherwise be heightened user expectations and avoid unintended outcomes.
Since the higher cost cards are priced at a level consistently at or lower than most vendors and carry a one-year warranty, and the less capable early cards are discounted from that level yet carry the same warranty, we think that they pair offer better overall value to most users under most circumstances. That said, they can be less expensive—or, more expensive—than some unsupported product sold on eBay. But, ours are tested and warranted, and the price has remained consistent across low and high availability situations, something that we again believe provides better overall value to buyers.
Sure, they might—in fact—support it, in some circumstances. But, we would be inundated with complaints from users wanting such support if the individual card they purchased did not support it when they received that specific card. While Apple claims that the original AirPort base station never supported WPA, you need only put a WPA capable replacement card in it and use the appropriate software to gain access to this feature. Components other than the card itself in an AirPort base station can be reasonably characterized as passive. It is the card itself that determines the capabilities of the base station.
We're currently out of the original cards, or I would arrange to ship you one of each to test in your own environment to satisfy your concerns. In our case, testing cards at one point for such capabilities reasonably satisfied us that M7600LL/A and B cards did not support WPA 'out of the box' and so we've simply pointed that out.
It's akin to saying that original iMacs based upon a G3 processor do not support the installation of Mac OS X, unless and until a suitable firmware update is applied. And that statement also is true, given that most shipped pre-OS X and without the installed firmware.
How do I put this? Most alternative suppliers in this industry are chumps: they know little, and care even less. It's all about 'turn and burn' to them, and they seek almost exclusively to maximize their opportunity. Despite their claims, they could care less about customers. You only have to look around the web to figure that out…
We've been quietly engaged in this market in the background for nearly twenty years, so we know a thing or two about the other players.
We find it too cumbersome to explain the capabilities of the original AirPort cards in general beyond what we describe, and not economical to upgrade the firmware of such cards and attempt to sell them as the second generation of that product line, thereby creating an instantaneous identification conflict.
When we receive and qualify additional cards, I will get ahold of you in The Lounge if you are interested in setting up a 'lab test' on your own premises, or modifying the A or B card by applying a firmware update.
To some degree, the argument is moot: Apple no longer supports the original card at all, and the second generation of the product line remains supported only in California, and only for a limited remaining time period.

Lastest Airport Card Firmware - How to tell?

How can I tell if I have the latest firmware for my airport card? I have a G4 15" Powerbook. When I query about this Mac, it show this as the latest firmware:
: 404.2 (3.90.34.0.p16)
The latest update is AirPort Extreme Firmware Update 5.7 for Mac OS X. Why don;t these numbers match?
I have been experiencing problems with my wireless connection lately, so I want to make sure I have the latest.
Thanks.

Well in my case, I am trying to update to the latest Extreme Card firmware,
but it does not appear on "Software Update".
I run a G5 with 10.3.9 and on the "System Profiler"
I have this firmware:
400.17 (3.90.34.0.p11)
This is not the latest, according to this topic, so
what can I do to update?
On apple.com I only find updates for ABS...
G5 1.8 mhz, 1.5 GB RAM Mac OS X (10.3.9)

Can an original Airport card connect to an Airport Extreme base station

I have an old iBook G3 10.3.9 with an original Airport card (System Profile says "Wireless Card Firmware Version: 8.70"). This computer/airport card connects fine with an old Airport Graphite.
But it will not connect with my main Airport Extreme 802.11n (1st Generation), running in 802.11n (802.11b/g compatible) mode. This Airport is using WPA/WPA2 Personal wireless security. This Airport Extreme works fine with my other computers and devices.
Does anybody know, offhand, whether it is just a setting, or is this completely unworkable?
Thanks in advance for any input.

I cannot remember all the details regarding the older iBooks, but suspect that the wireless card and possibly the operating system that you are using on the iBook cannot support WPA/WPA2 wireless encryption.
As a test....
Temporarily turn off the wireless security on the 1st Gen AirPort Extreme, then see if the iBook can connect to the wireless network that way.
If it can, this tells you that the wireless is at least working on the iBook....but it cannot connect to the WPA/WPA2 network.
The solution might be to use a USB wireless adapter that can handle the higher encryption levels, or connect the iBook using Ethernet.
If the iBook still cannot connect when security is disabled during the test, then the iBook has additional issues that you may or may not wish to pursue.

Airport extreme firmware update screwed up my IP sharing and internet

I am having all the same problems -
1) I upgraded to the 7.1 firmware
2) I got the 'double NAT' error, but no problems connecting to the internet
3) When I turned the bridge mode to off, I lost my internet, so I
4) Tried to turn the bridge mode back to Share an IP address, but got an error about IP addresses.
5) I went into Setup - the network port mapping tab - and unchecked and then re-checked the Airport button, so now I have internet access, but only at one computer, and if my computer is functional, my VOIP modem is not (or vice versa)!
6) when I tried going back into "Share an IP address", I got the same error about the beginning and end DHCP conflicting with my WAN.
(If it helps to know, I have two AEBS - one is set up as the Main WDS station, and the other Participates in that WDS)
Now I'm afraid to touch anything!!

kayek wrote:
I have installed the new AirPort Extreme firmware update (7.4.1) and with airport disk utility i want to connect automatically my hard drive related to the airport (wifi mode) , the connexion was working well before that update and now i have an error message (unknown user or wrong password error -36 ...) when the disk tries to connect automatically.
I would like to rollback to the 7.3.2 firmware version but there is no way to find it on internet (or on apple download) even if i change rollback airport utility to version 5.4.1: the binary firmware 7.3.2 disapeared from my mac and i can only choose 7.4.1 binary file ...
Do anyone have the same problem ?I you found how to fix it please answer my post (thanks)
Ok, here's how you actually do the downgrade - here's what Apple says, not exactly right - I would add that you HAVE to go to the MENU, choose BASE STATION, then hold down the Option key while pressing UPLOAD FIRMWARE, this will get you to a window that has the dropdown with older versions....the other versions were not available to me any other way.
{quote}If I have a computer or device that does not work well with an AWD with the latest update, how can I install previous (earlier) versions of firmware?
1. Open AirPort Utility.
2. From the AirPort Utility menu, hold the Option key (Control key in Windows XP and Vista) and choose Check for Updates....
3. Select the specific firmware version you require.
4. Click Download.
5. Select your base station and choose Manual Setup from the Base Station menu, or double-click on the AWD icon.
6. Choose Base Station > Upload Firmware.
7. Select a firmware version and click OK.{/quote}

Airport Extreme Firmware Update 7.3.2 no longer connects to internet

Automatic Updates recommended Airport Extreme Firmware Update 7.3.2, which I accepted (BAD). The Airport Extreme does have a green light, but CANNOT connect to the internet. Cannot "Check for Updates" with Airport Utility (option key down) because I cannot access the internet. Airport Utility shows 7.3.2, but nothing lower. Is there a location on the mac where the older driver resides?
Numerous restarts, resets, etc with both the Cable Modem and Airport Extreme and my MacBook do not help.
How do I download 7.3.1? Can I? How can I revert?
I can access the internet from another network, hence this email.
Any suggestions would help!

When I updated to the Airport Extreme to 7.3.2 firmware it was dropping wireless connections randomly, Today I reverted back to 7.3.1 and looks like it is staying up for now but I am still shell shocked. To revert back in Airport Utility:
1) Hold down the option key(Mac), the Control key for Windows at the same time clicking on Check for updates
This will open a popup window with the previous versions, select the Airport Extreme Firmware 7.3.1 update and click download.
2) After the download is done, from Base station file menu drop down select Upload Firmware, you will get a choice to download different firmware updates, select 7.3.1.
That should install the 7.3.1.
There you go enjoy.

Trouble Connecting Original Airport card on eMac 700 to wi-fi network

I have an eMac 700Mhz with an original Airport card (801.11b).
The card will find our home Wi-Fi network (Linksys 801.11n)but when I provide the WEP password, the eMac Airport Card will not connect. Any ideas
Thanks!

KB article HT1126 could perhaps be of interest to you. See also KB article HT1344.
Jan

Original airport card mysteriously stopped connecting to network

i have a powermac G4 tower and have been using the original airport card for about four months. Just recently it stopped connecting to the network at all. the bars are all gray on the menu bar and when i try to connect to any network in the drop down menu the popup window just says "there was an error connecting to the specified network" when I go to network diagnostics and try to connect it asks for a WEP pasword even though none of the networks require a password and network security is set to none in system preferences for the network. I've been able to get a connection back a couple times but it was only by restarting my computer and that hasn't worked for a couple days. Is my airport card broken or is there something wrong with the operating system? I've also talked to the tech support people for the wireless network I'm using and they had no clue how to help me.

I had trouble getting my Airport card online for the longest time. Finally, I ditched the Linksys wireless router I was trying to use, and switched to a D-Link. I still don't always get full signal, but I can get online 95% of the time.
Have no idea why it worked, but it definitely works better than the Linksys.
PMG4 (3.4), Silver Door, FW400 Mac OS X (10.3.9) Dual 1.25, 512 RAM, original Airport card

Original airport card connection to Belkin Wireless G Plus router

I have an iBook G3 with an original airport card in it. The card works because I can acess the internet at school or the local Wi-Fi hotspots. I cannot however connect to my own network at home. The computer will pick up my network but when I try to connect I am asked for a password. I DO NOT have NEVER HAD a password for my network and my PC will connect wirelessly just fine. I have read the manuals for every thing I have and can not figure out why it wont connect. Any suggestions other than getting a new computer?

Already tried that
Is the Belkin running in 802.11g mode?
It needs to be running in 802.11b or 802.11b/g mixed mode for a Mac with the original Airport card to connect.
Has the Mac been able to connect to any wireless network?

Apple original Airport card and AEX

I have an iMac slot loading SE 600mhz and want to connect with my wireless network via Airport Express. Are there any compatibility issues witth the Apple originla Airport Card? I am about to bid on ebay but thought I should check. Any help out there?

A Mac with an original Airport card will work perfectly with the Airport Express - the only requirement is that the Mac is running a minimum of MacOS 10.3 in order to be able to configure the device.

Original airport card

I bought an original airport card for my 2000 Imac. Any idea where I can get an adapter to install it?

I found it on ebay for $21 US

Anyone ever tried to use an original airport card in an emate 300?

I know it sounds crazy, but I am attempting to think outside the box and save money.
Lemme know what you think of my crazy idea, please!

The original Airport card may look like a PCMCIA card, but it is not. It won't work in a slot that was not specifically designed to accept it. It doesn't even have a built-in antenna.
Also, I suppose that it would save money if you already have one. But those original Airport cards sell for $40-50 on eBay, including shipping. You can get an 802.11b wireless PCMCIA card on eBay for less than $20 including shipping. You'd make some money if you sold the Airport card and got a generic card that is known to work in that slot.

Original Airport cards and e-Bay

I have a 17inch flat panel iMac, 800 mhz speed and am thinking of going wireless. I know I need an original airport card for my computer, NOT the airport extreme. I have been searching on e-Bay and found various sellers with a huge difference in prices. My question is: are there different models of the original airport card? One vendor lists an airport card model # M7600LL/A for a high price, but in the information it lists my computer as one of the models this card will work with. Another vendor has an airport card model # M7600LL/E for a much lower price but the information on the card's compatability is rather sparse. Are they the same card just with a different price? What is your advice about buying an airport card from e-Bay in general? I will also need a wireless router and have my eye on a Linksys model that a few of my friends have in their wireless networks and they recommend it highly. Any thoughts on that area?
17 inch Flat panel iMac, 800mhz Mac OS X (10.3.9)

Basically the difference between the two is one was for American market I believe and the other the European market.
Both should work fine.
Original Airport Card Alternatives
http://www.ifelix.co.uk/tech/1030.html
A Mac with an original Airport card can connect to any wifi certified 802.11b wireless network (or 802.11g in backward compatible mode).
Out of all the different wireless routers I have used, I have found my Airports to be reliable and easy to setup.

Original Airport Card Firmware Update?

Similar Messages

Maybe you are looking for