OS 10.10.1 update didn't solve wake from sleep issue

Since I installed Yosemite on my late 2009 iMac 27", it doesn't wake from sleep properly. I get a grey screen with my account photo and nothing else. A hard reset is then all that helps. I have disconnected all audio devices and zapped the PRAM, to no avail. Any ideas?

Something wrong's here. If you have a Retina, that means you have a flash drive - which means a boot time of maybe twelve seconds.
Since it's a new machine, I strongly suggest you visit your local Apple Store. Please post with your results!

Similar Messages

OS X 10.7.3 WiFi Update for iMacs and Wake from Sleep Problem

http://support.apple.com/kb/DL1501
Apple has released a software update for those suffering from the iMac wake from sleep/wifi connection issue that resulted from updating to 10.7.3. It fixes the problem for me and several others. For those still suffering this issue, download it and see how it works!

To answer my own question it seems a workaround is to wake the iMac up using the power button rather than the keyboard. The WiFi reconnects this way.

U430 BIOS Update Procedure (fixes wake from sleep issue on Windows 8.1)

Hopefully this will make the BIOS update process a bit easier. The following steps address two common questions (Failed BIOS Update and the Windows message about improperly configured Secure Boot). NOTE: After a successful BIOS update you will want to check additional items in the BIOS not directly covered in the steps below (e.g. Intel Virtualization.... the update disabled this for me.)
U430 BIOS Update Procedure:
1. Download the BIOS update from Lenovo (it will be in .exe format... the program will install new BIOS).
2. Shut down computer.
3. Use the "Novo" button (tiny button on left side near Power button).
4. Enter BIOS setup.
5. Under "Security" select "Secure Boot" and choose "DISABLED" (this allows the BIOS update program to work properly).
6. Under "Exit" select "Exit Saving Changes".
7. Computer will reboot. Log in to Windows (it will have a message stating "Secure Boot not configured properly" this is expected).
8. Run the Lenovo BIOS program (this will reboot the computer and you should see an update status screen). Once finished, the computer will reboot. Log in to Windows (the "Secure Boot" message will still be there) and then turn the computer OFF (I've found that turning off the computer from the log-in screen doesn't completely shut down the computer. If that's the case then hold the Power button until it does shut down).
9. Use the "Novo" button and enter BIOS setup.
10. Under "Security" make sure "Secure Boot" is ENABLED.
11. Also under "Security" select "Restore Factory Keys" and hit Enter. Select "YES" (this step along with our previous step will make Windows happy).
12. Under "Exit" select "Exit Saving Changes" (computer reboots and all should be fine!)

Hi,
Generally speaking, this problem should be caused by hardware driver problem. Such as Graphic driver, NIC driver, etc. Please check computer driver edition, make sure they are compatibility with Windows 8.1.
Actually, I made a search on Acer official site, the model of your computer doesn't have all hardware driver provided for Windows 8.1. Such as Graphic driver. You can refer to the link below for more details.
http://us.acer.com/ac/en/US/content/drivers
In my opinion, it would be better to contact ACER, to check whether this serial computer had the same problem with yours.
Roger Lu
TechNet Community Support

Display no longer wakes from sleep after latest updates

G4 Quicksilver 933, nVidia Ti, 1.5GB, 20in Cinema Display
I applied the latest updates that were pushed out recently (10.5.2 and the "Leopard Graphics Update") and now my Apple display will not properly come up when I wake the box from suspend.
That is, it starts and runs fine, but if it goes into sleep, upon waking it will (sometimes) flash the contents of the desktop, and then go black. The litte green light is on. Happens from a logged in session, or from the main login screen.
I have to hit the reset or power button (or login via SSH and issue a shutdown) to get it to work again.
I only have a single monitor.
I tried:
o Powering the monitor off and on, both from the switch and by pulling the power cable
o Pulling the DVI cable and reinserting it
o Resetting NVRAM
o Re-applying both the 10.5.2 combo installer and the Leopard Graphics Update 1.0 in order
o Waving a magic wand... I mean, fixing permissions
o Changing the display resolution a few times
o Running fsck a few times (only because all these unclean shutdowns are making me nervous)
o Hitting the "Detect Displays" button in the Displays Prefs panel...
Aha! Hitting that button causes the display to flash and then go dark. I have to power cycle the unit to get the monitor to come up again.
I do have the special build option of the faster video adapter which was available all those years ago. It's quaint now, sure, but it was a fast card back then.
I'm stumped. It's surprising how something like this can turn a perfectly reasonable desktop into a boat anchor.
Message was edited by: John Verne

mjelacic wrote:
This Discussion is marked as Answered, but with my apologies to the other respondents, it is NOT. There is a problem. The software/hardware do NOT work as they are supposed to. Apple needs to address this problem immediately. Mac Book Pro will not wake from sleep when connected to a Cinema Display 23". The problem lies in the most recent operating system updates. Before the update the products worked as advertised, since then they do not. Period.
With all due respect, I am the one who posted this, and I marked it "answered." Yes, there very well may be a problem with the Leopard Graphics Update 1.0 (what a mouthful! I dub it "LGU v1.0" from this point on.), but this is so far only a hypothesis.
I found an immediate workaround which suits my purpose. If this does not suit the purposes of completely foreign (to this discussion) symptoms related to Intel-based Apple laptops and external displays, then so be it. I recommend splitting off your own symptoms to a new thread.
Certainly, my reading of the symptoms described after I posted mine mostly do not sound like what I ran into at all. For example, I never once said that my computer had problems waking from sleep. I said the /display/ had problems waking/starting up after sleep, and this is probably related to the "detect displays" mechanism that the OS uses to find attached displays when it comes out of suspend. Even if this is my misunderstanding it does not matter, since this is how it comes across to a reader. This may indicate that someone may want to clearly and carefully describe /exactly/ what they are seeing, and the steps they took in order to come to any conclusions they might have.
This will help Apple, and it will certainly help others that search these threads with their own similar but different issues they need solved.
If there is a common reproducible issue related to displays and the most recent update(s), then Apple already knows about it, or soon will. As far as my immediate needs are concerned, this is answered.

IMac will not wake from sleep after 10.4.8 Update

Recently after a couple of software updates my IMac goes to sleep and the Bluetooth keyboard and mouse will not wake it. The option for wake with Bluetooth is checked. I zapped the PRAM and also checked the HD, Nothing has changed. NOTE: No new software or hardware installs were done except for 10.4.8 update and the other mac software updates. This did not happen in prior versions of the OS on my iMac. Is this a new bug?
iMac G5 1.8 (pre iSight) Mac OS X (10.4.8) Bluetooth, Wake from Sleep

I've been dealing with this same issue, have tried everything, but to no avail. After MANY sessions on the phone with Apple tech support, as well as an Apple product specialist, I was advised to erase my computer and do a fresh install. I did an archive an install, which didn't help, but am not thrilled about the prospect of erasing everything and starting over. This problem started after the August 2006 round of updates. I feel it's bluetooth related, because I used a usb keyboard and mouse for a week as a test, with no problem. The funny thing is, I unchecked "allow bluetooth device to wake computer" thinking it might help, but the bluetooth devices continue to wake the computer anyway (except when it refuses to wake, of course!)
Jerry

10.9.4 update causing internet browsing errors after wake from sleep

Macbook Pro Late 2011, OS X 10.9.4
So before the 10.9.4 update, I had no problems with Wifi and wake from sleep.
Now, after the update, random web pages either don't load (Chrome & Firefox) or return a "Memory Not Allocated" error (Safari). Also, my Work VPN application stops being able to connect. The related Console error is:
acvpnagent[104]: Function: getInterfaces File: ../../vpn/Common/Utility/NetInterface_unix.cpp Line: 1277 missing PPP destination address for interface "utun0"
The only solution I've found is restarting.
Any ideas?

Remove the Cisco VPN client. Use the built-in client, if possible.
Any third-party software that doesn't install by drag-and-drop into the Applications folder, and uninstall by drag-and-drop to the Trash, is a system modification.
Whenever you remove system modifications, they must be removed completely, and the only way to do that is to use the uninstallation tool, if any, provided by the developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job.
I never install system modifications myself, and (unless otherwise specified in this comment) I don't know how to uninstall them. You'll have to do your own research to find that information.
Here are some general guidelines to get you started. Suppose you want to remove something called “BrickMyMac” (a hypothetical example.) First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickmymac.com. (That may not be the actual name of the site; if necessary, search the Web for the product name.) If you don’t find anything on the website or in your search, contact the developer. While you're waiting for a response, download BrickMyMac.dmg and open it. There may be an application in there such as “Uninstall BrickMyMac.” If not, open “BrickMyMac.pkg” and look for an Uninstall button. The uninstaller might also be accessed by clicking the Customize button, if there is one.
Back up all data before making any changes.
You will generally have to restart the computer in order to complete an uninstallation. Until you do that, there may be no effect, or unpredictable effects.
If you can’t remove software in any other way, you’ll have to erase and install OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
WARNING: Trying to remove complex system modifications by hunting for files by name often will not work and may make the problem worse. The same goes for "utilities" such as "AppCleaner" and the like that purport to remove software.

IPhone will not wake from sleep and locks up with new MMS update

Hey everyone,
Has anyone had these problems with their new update as well?
1) Sometimes my iPhone will not wake from sleep mode, I have to hold down both buttons for it to restart...I do this about 5 times a day!
2) I cannot send SMS messages and when I send more than one sometimes the iPhone locks up and will not unfreeze.
Does anyone know if this is an Apple update issue or if it is an AT&T issue? And if this is being addressed?
Apple, if you read this could there be an update to all members what is going on?

I am experiencing the same issue with iPhone 3GS. After yesterday update to 3.1.2, it is a bit better in the sense that I can restart the iPhone slightly faster but still getting frozen screen during a call. I will try to call support once more. I don't believe that the problem is solved in the new update.

Wake from sleep volume extremely loud after 10.9.4 update

Every time I wake from sleep since the 10.9.4 update, my Mac Pro's volume to my speakers (via headphone jack) seems to be insanely loud despite system prefs showing the volume level at middle. Normally I like to keep my speaker's volume high and turn the system volume down, but it seems like the OSX is ignoring the system volume setting after waking up. It reverts to proper behavior when I hit volume up or down on the keyboard. Anyone notice this?

Reset the NVRAM.
NVRAM reset:
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
After resetting NVRAM or PRAM, you may need to reconfigure your settings for speaker volume, screen resolution, startup disk selection, and time zone information. If issues persist, your Mac's logic board battery (not a portable Mac's rechargeable battery) may need to be replaced. The logic board battery helps retain NVRAM/PRAM settings when your computer is shut down. You can take your Mac to a Mac Genius or Apple Authorized Service Provider to replace the battery on the logic board.

Crashes after wake from Sleep after 10.8.1 update

2.5 Ghz Mac Mini (mid 2011), 8 Gigs of RAM
Since the day I upgraded to 10.8.1 I have had persistent crashes, 1 every 24 hours or so. It's always shortly after a wake from sleep. In all cases, it is impossible to switch to a random open application. But once I hit that application, no other application will respond to anything, including a Force Quit, or if it will force quit, it won't relaunch. A shut down will hang because an app refuses to quit. I can quit the Finder, but it won't relaunch. Have reinstalled Mountain Lion twice, zapped the PRAM, reset the SMC, checked and extensively tested the HD and RAM. Replaced RAM with original Apple RAM. Didn't help, so I swapped back to the RAM from Crucial. I can't think of anything else to try. Machine does not crash unless it has been asleep. Runs flawlessly when sleep is disabled. After a reboot (usually via a shut down via the power switch, start from scratch, check of the HD integrity, and then a clean restart) the machine will run fine, sleep and wake normally for about 24 hours. As near as I can tell from the logs, the hangs usually begin right after the Time Machine Backup after a wake from sleep finishes. If I don't allow the machine to sleep, there are no problems of any kind. Making me crazy. Did not occur under Lion or the .0 version of Mountain Lion. Is making me crazier than I normally am which is sorta serious.

Any solutions to this problem? I too have this kernel panic, however it only happens about once a week. Always upon wake from sleep as you've indicated.
FYI I don't have intego software, or an APC installed. Nor am I using filevault.
This is on an up to date, MacBook Pro Retina.
Robert

One wake from sleep solved

Time will tell if it is truly solved but I noted a comment about my screensaver /desktop path in a recent crash report when I had to hard reset after my machine would once again refuse to wake from sleep. After looking at my picture folder that was set for my desktops and screen saver I realized there was / in the name of the folder. I know enough to warn others not to use / in any name. My machine woke properly this AM, although there is some oddity left because in the System Pref, with my folder added and selected for the Desktop use, I can't see any of the individual jpg images in the folder I chose. I can see those in the Nature, Pants, etc folders, but not those in my folder. They are, however working and the wake from sleep problem -seems- gone. We'll see.

nope

IMac (Early 2009) always wakes from sleep after Security Update 2010-001

I posted this already in the Snow Leopard section, but wasn't able to get a resolution to the problem:
http://discussions.apple.com/thread.jspa?threadID=2309613&tstart=0
I tried all the suggested things, but my iMac still always wakes from sleep and this never happened before the 2010-001 security update. I was asked to paste the console log entry from when this happens, so here it is:
28/01/2010 08:57:47 kernel Wake reason = OHC2
28/01/2010 08:57:47 kernel System Wake
28/01/2010 08:57:47 kernel Previous Sleep Cause: 5
28/01/2010 08:57:47 kernel USB (OHCI):Port 1 on bus 0x6 has remote wakeup from some device
I'm wondering if others have seen this and if so know of a solution. At the moment I'm stuck with having to shutdown my iMac every time I leave it. Thanks.

Here is a solution that should work:
1. Turn off all Bluetooth devices connected to your computer.
2. Make sure Bluetooth icon in the Menu Bar is black (BT is On) and BT is not connected to anything
3. Plug in a USB mouse
4. Go to System Preferences>Bluetooth>Advanced
5. The option to "Allow Bluetooth devices to wake this computer" should now be uncheckable>Uncheck it and click OK
6. Turn on your Bluetooth devices and let them connect to your Mac
7. Try and put your Mac to sleep and then wake with the power button
8. Check if the "Allow Bluetooth devices to wake this computer" option is still unchecked (it should be)
9. Try and restart your Mac and check again if the "Allow Bluetooth devices to wake this computer" option is still unchecked (I had mixed results with this test, depending on the type of the Mac being tested)
Anyhow, this way you should be able to uncheck the option that causes the issue and it should not get checked again by itself unless you restart your computer and maybe even after that. If it does get checked again after reboot, just get used to putting your Mac only to sleep until a fix from Apple is available or repeat the above process after every reboot if necessary.
Hope this helps.
Marian

"Wake from sleep" grayed out and BT firmware updater won't work

I've read a number of postings related to ways to correct the grayed out "wake from sleep" option in the Bluetooth prefs pannel, which is a problem I'm having since switching to a Apple Bluetooth keyboard and mouse. The problem I seem to be having is that the Firmware 1.2 updater for the DBT-120 Bluetooth adapter will run, but won't seem to actually flash my adapter (i.e., it won't actually update the device). It is H/W ver: B4, and is plugged directly into a USB port on the back of my fairly new G5 tower, so it seems like it should work.
Any ideas? Thanks!
Dual 2 GHz G5 Mac OS X (10.4.6)

That did the trick! My old G4 tower (Yikes!) was able to flash the BT adapter with the firmware update without a problem, even though my G5 was unable to ever finish the process. Once I plugged the updated adapter into the G5 the "Wake from Sleep" option was available and already selected.
Thanks so much for the tip-- I can finally put this question (and problem) to rest.
Dual 2 GHz G5 Mac OS X (10.4.4)

Mac book pro won't wake from sleep after Yosemite update

Since updating my laptop to Yosemite my MacBook hasnt woken from sleep
i can hear it turn on but the screen and keyboard don't light up
mac book is only 3 years old retina display

Mike Doolin wrote:
I think I may have found the fix for this. My MacBook Pro was dying in its sleep every time (after installing Snow Leopard), whether it went to sleep automatically or I used a Hot Corner. I went into System Preferences>Desktop & Screen Saver and changed the screen saver to Flurry, and it works now. I had had it set to a folder containing a single .pct file that I had created.
Good advice Mike! When in doubt check the ScreenSaver settings.
Definitely seems that it has a problem with that pic... In my case, selecting any images instead of the default setting (no screensaver) seems to have cured my non waking issue on my early Macbook Pro in Snow Leopard.
My original problem was that no amount of trackpad input woke it, but the space bar did. The space bar seemed to wake it up with the previous Screen Saver setting. Now trackpad wakes it up (even from total sleep as well as screen saver), too. Might be nice to know about if this is an intended 'feature' as a security trick. Otherwise I consider this a bug.
My vote is that it's a bug.

Firefox 15 UI does not update after wake from sleep

On my Netbook running Windows XP 32-bit, if I leave Firefox open when I put the computer to sleep (by closing its lid), then when I wake it up from sleep, the user interface elements (like the tab bar) won't respond to mouse clicks. This does not happen 100% of the time; in particular it won't happen for a freshly restarted Firefox that is put to sleep, making the problem rather annoying to reproduce. As far as I can tell, I might have to visit some set of websites with Javascript or Flash or something.
Here are some more details about the user interface, because it is not as simple as non-responsiveness. When I wake it up, when I click on a tab to switch to it, the Windows title bar actually changes to display that tab's page title, but nothing else in the UI updates including the URL bar and the actual page displayed. Similarly for closing a tab; the tab remains, but the title bar shows the title of the tab that would receive focus next. After I "pseudo" close a tab and then restart Firefox, it does not remember that I closed the tab (I save sessions) and restarts with the same set of tabs before I tried to close one.
I get the problem even after disabling all extensions and resetting all toolbars to defaults. I have not tried to create a new profile because I have a lot invested in my current profile.

I am going to respond to my self and say I am nuts.
Canon does not seem to have any uninstaller for this scanner on their site:
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDet ailTabAct&fcategoryid=351&modelid=17104
Which is rather odd since they have installers. this is different from most of their other older scanners. But if you just plugged in our scanner and things worked in OSX, which it should have, then you should be OK.
However I can confirm that others see this issue (like my dad) and here is the official Canon response to the issue:
+Dear XXXX:+
+In some cases, coming out of sleep mode may not properly reinitialize+
+the USB bus on Macintosh Operating Systems. Unfortunately, the only+
+work around when this happens is to restart the computer.+
Of course this in not exactly true as logging out and back in fixes it.

[SOLVED] Problems restoring network on wake from sleep - Zbox AD04

I have some issues with restoring the wired ethernet connection when waking from sleep. Sometimes it takes 1 or 2 minutes before it comes back up and sometimes it won't work at all unless I restart (usually when it has been in sleep for hours).
The network is configured to a static IP address in rc.conf. Hardware is a Zotac Zbox AD04 (AMD Fusion E450 system) using the r8169 driver. I guess this is probably a driver issue, but I wondered if there's anything else which I could do to solve the issue. I've tried adding r8169 to SUSPEND_MODULES, but that seems to make no difference.
Another issue is that the network is "unreachable" for about 30s to a minute after booting.
Could it be a problem with my router?
Last edited by shaurz (2012-04-13 01:03:13)

I haven't really found anything much in my logs. From the kernel message log:
[ 3.457080] r8169 0000:02:00.0: eth0: link down
[ 3.457146] r8169 0000:02:00.0: eth0: link down
[ 3.458714] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.573639] EXT4-fs (sda3): re-mounted. Opts: discard,commit=0
[ 88.121693] r8169 0000:02:00.0: eth0: link up
[ 88.123403] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 98.483350] eth0: no IPv6 routers present
It seems it took 84 seconds after initial setup for the network to come up...
Something a bit odd in errors.log:
Apr 12 20:20:07 zedbox kernel: [ 2.030578] SP5100 TCO timer: mmio address 0xbafe00 already in use
Last edited by shaurz (2012-04-12 21:51:05)

OS 10.10.1 update didn't solve wake from sleep issue

Similar Messages

Maybe you are looking for