OS 8.6 reinstall/Cannot find destination hard disc

I have initialised the drive on my G4 power pc and am attempting to reinstall the original OS 8.6 from CD rom. It boots up from the this disc but cannot find destination hard disc to reinstall software to. What should I do?

Hi, pjam007 -
It is sounding more and more like the drive has failed, although it is possible that the controller for the ATA bus has failed. The test for either is the same - get another drive (a known-good one, or a new one) and see if it works. If it does, then the original drive failed; if it does not, then the controller has probably failed.
Caveat - sometimes a too-weak or dead internal battery can cause serious booting problems, although since the machine will boot to a CD it is doubtful that this is the cause of the current problem. Nonetheless, if you do not know for sure that the battery has been replaced within the last four years, or if the machine has been left unplugged for an extended period, I would replace the battery anyway.
While replacing the battery, it would be advisable to also reset the CUDA or PMU, as appropriate -
For a G4 (PCI) model -
Article #95065 - G4 (PCI) - Resetting Cuda
Article #95066 - G4 (PCI) - Resetting the Logic Board
For a G4 (AGP) model -
Article #95037 - G4 (AGP) - Resetting PMU

Similar Messages

  • Tiger 10.4.3 Installer Cannot Find Destination Drive

    I am trying to upgrade[finally] from 10.2.8 to 10.4.3 using the installer disc, but it cannot find my hard drive for it to install. I have run a repair[ Disk & Permissions] using Disk Utility, everythings fine. Have run an Apple Hardware check and again eveything fine. Through System Preferences/Startup Disk It sees my disc no problem and everything is running smoothly and quickly, so I'm a bit worried why the installer disc is unable to see my hard drive.
    Any help with this would be much appreciated, Sorry if this query has been answered elsewhere, I had a good look before I added this entry and couldn't find an answer.
    Thanks for your time.
    Power Mac G4 Quicksilver[Mirrored Drive Doors]   Mac OS X (10.2.x)  

    Had a go but the DVD's Disk Utility simply couldn't see my hard drive went on the System Profiler off the installer disc and again the only disc it could see was the DVD itself, No other ATA drive or Serial ATA drive. Rebooted the computer as normal and the system profiler saw the hard drive with no problem. I unplugged all peripheral hardware like DVD Burner, Scanner and Printer, and my Firmware is all up to date as your checklist suggested too.
    Was wondering, my hard drive has it's jumper set to "Enable cable select", When starting from the Installer disc does that cause a conflict about which disc is master and results in the disc not being seen?
    (Sorry if this is a silly suggestion, it doesn't take long for this technical stuff to baffle me, as you can tell)
    Thanks again for your help.

  • Cannot find my hard drive connected to my extreme

    Hi - I am using a Windows 7 PC and cannot find the hard drive connected to my airport extreme.  I have gone into manaul set up on the extreme and asked it to share the files which it has confirmed, yet when I go into windows explorer I cannot see the drive at all ...... can I please ask for some assitance?

    Just want to be sure of three things first if you don't mind:
    Does the 802.11n AirPort Extreme Base Station (AEBSn) have a Base Station Name that includes a space? For example: My AirPort Extreme. If it does, rename it so that it does not have any spaces or use the underscore character between words.
    Does the shared HDD have a volume name that includes a space? If it does, again, remove them or add underscore characters.
    Is the HDD formatted in NTFS? If so, the AEBSn does the best job of sharing HDDs formatted in HFS+, then FAT32. It will NOT work properly with HDDs formatted in NTFS. If the HDD is very high capacity, you may want to borrow a friend's Mac to format it in HFS+ or get a utility that lets your PC format/read/write to HFS+ volumes. Regardless of it being formatted in HFS+, the AEBSn will share it out using both the AFP (for Macs) and SMB (for Windows/Linux) file sharing protocols ... so Windows PC should not have any difficulty accessing it.

  • This morning my PB G4 would not get to the password screen after power on.  I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage E

    this morning my PB G4 would not get to the password screen after power on.  I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage Error Code" message.
    Did my HD just crash and unrecoverable?  Time to replace my notebook?

    I believe your hard drive has failed. Hope you have a backup.
    Failing Hard Drive Sounds http://datacent.com/hard_drive_sounds.php
    Listed by drive manufacturer.  Click on the > next to the drive & you will hear the typical failure sound.
    How to Tell When Your Hard Drive is Going to Fail
    http://www.lifehack.org/articles/technology/how-to-tell-when-your-hard-drive-is- going-to-fail.html
    Grinding And Clicking – Symptoms Of A Failing Hard Drive
    http://pcperformancetools.com/getdata/grinding-and-clicking-symptoms-of-failing- hard-drive.html
    Failing Hard Drives
    http://losangelescomputerhelp.com/computer_networking_news/failing-hard-drives.h tml
     Cheers, Tom

  • Even when I select a playlist I cannot find the burn disc option under file. How do I find it?

    Even when I select a playlist, I cannot find the burn disc option under the file tab.  How do I go about finding it?  It has always worked previously, or at least until the latest version of Itunes installed. 

    Hi Hatethecloud
    Have you tried to make a control+clic on the playlist name ?...

  • Cannot find destination drive - Powerbook G4, Tiger

    Hello... oddball problem here I think.
    My powerbook is about 4 years old now. Was running fine on Sunday, Monday when I tried to start it up I got the "broken folder" icon. i.e. Kernel Panic as far as I can tell.
    I've:
    -Reset PRAM
    -did extended hardware test (no issues)
    -repaired and verified the disk (via TDM)
    -did a 7pass '0 out' erase of OS partiton (via TDM)
    -did a quick erase and rename of OS partition (via TDM)
    -repaired and verified the disk (again) (via TDM)
    I can access the HD via firewire in TDM, can transfer data off it no problem.When trying to use Disk Utility from the OS startup disk, it freezes up. When trying to reinstall the OS it cannot find a destination disk..
    so.. Is the HD dead? or am I missing something?

    Well, maybe you did have a KP which may be hardware related. I take it the gray disc is the one that came with the computer originally? I am not that familiar with your model computer but the disc probably had a hardware test utility on it that can be accessed by holding down the D key while booting. Check the hardware.
    There's a list of other things that can be tried such as resetting PRAM (can't see how that would necessarily help here, but it can't hurt) and PMU.
    In one sentence you said it freezes on booting, but then you also said it froze while using disk utility which suggests it did indeed boot to the disc, so I'm a bit unclear as to the exact status.

  • Can't Find A Hard Disc to install

    I'd like to add an additional Hard Disc but cannot find one for the older MacPro version. Is there somewhere on this site I can buy one? If not, why? More importantly, where can I buy one?
    Processor 2x2.66 GHz Dual-Core Intel Xeon
    Thanks in advance!

    You have posted to the MacBook Pro forum not the Mac Pro forum here:
    http://discussions.apple.com/category.jspa?categoryID=194

  • Disk Utility cannot verify External Hard Disc

    Hi,
    Trying to get Disk Utility to Verify and repair an external Hard Disc, which is seen but only as 'disk1s1' not it's proper name. On plugging in it asks if I want to initialise the disk - obviously No.
    DU sees the HD in the side bar but it's grey'd out, I can't mount it, Verify is greyed out.
    Running diskutil in Terminal (which I'm not confident in) brings back the following - disk0 is my OS, disk1 is an install disk of Disk Warrior and disk2 is the external one I'm trying to sort out, as you can see it's got an FDisk_partition_scheme, which I think is the problem.
    (BTW Disk Warrior doesn't recognise the disks either, however as this is an Apple Forum, I've not asked for advice on that here, unless someone wants to chime in on that software!)
    I'm running OS 10.9.5, and it happens on multiple external disks, running in USB caddies of different manufacture, I've tried different cables, ports, restarts etc.
    MBP 2.5GHz, i7, 16Gb, 500Gb SSD HD
    Any advice would be most welcome as how get correct this
    localhost:~ anthonyupton$ diskutil list
    /dev/disk0
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:      GUID_partition_scheme                        *500.3 GB   disk0
       1:                        EFI EFI                     209.7 MB   disk0s1
       2:                  Apple_HFS Macintosh HD            499.4 GB   disk0s2
       3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
    /dev/disk1
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:                            DW                     *67.6 MB    disk1
    /dev/disk2
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:     FDisk_partition_scheme                        *3.0 TB     disk2
       1:                       0xEE                         375.1 GB   disk2s1
    localhost:~ anthonyupton$ sudo gpt recover /dev/disk2
    Password:
    gpt recover: /dev/disk2: no primary or secondary GPT headers, can't recover
    localhost:~ anthonyupton$ diskutil repairDisk /dev/disk2
    Unable to repair this whole disk: A GUID Partition Table (GPT) partitioning scheme is required (-69773)
    localhost:~ anthonyupton$

    That is just a statement of optimization. It is not stating that there IS or IS NOT any errors on the disk. DiskWarrior does not actually have a separate "error detector" function. You basically let it run its disk directory data optimization routine on the volume. If it finds problems, it will attempt to fix them as it goes.
    When it finishes, it will let you review its findings and results, and then you get to choose to apply the changes or not. Until you apply the changes, you are safe; if you do not apply the changes, the drive is not changed. If you apply the changes, DiskWarrior will replace the existing disk directory data with the optimized (and repaired if there was damage) version.
    You should make backups of your valuable data before making repairs, in case something bad happens during your attempt to repair.
    Be sure your copy of Disk Warrior is compatible with the Mac OS X release. Version 3.0.3 or later is compatible with Tiger.

  • Time Machine cannot find external hard drive

    I have just recently purchased an airport extreme and have enjoyed being able to plug in an external hard drive for time machine. I think I must have reset my laptop while it was backing up because now I get an error every time it tries to back up. The error I get is disc image cannot be accessed (error 2) I have tried everything I can think (reseting router, unplugging and plugging back in the hard drive, changing networks, and then back) but still nothing. I am not even able to enter the time machine to back up to a time before I had this problem. I can however access the contents of the drive just not successfully complete a time machine back up. Thanks for the help

    Hi, and welcome to the forums.
    Start by Repairing the sparse bundle that contains your backups, via #A5 of the Time Machine - Troubleshooting *User Tip,* also at the top of the +Time Machine+ forum.
    If that doesn't help, try a "full reset" per #A4 there.
    You do need to know that backing-up this way is "iffy" and +*not supported+* by Apple. See the Using Time Machine with a USB drive connected to an Airport Extreme *User Tip,* also at the top of this forum.

  • N9A2 Platinum, Installing XP Pro, SP2, Cannot find SATA Hard Drives

    I am lost here.  I cannot get the bios to recognize the HDs as SATA drives, and XP Pro does not find the HDs (of course), and I do not know why.  Do I need a SATA driver floppy for the Install Win drivers <f6> ?  I thought not from the other threads here.  I am not using Raid.
    I have downloaded and read the manual from the support site, Support knowledgebase and every thread that I could find here in this forum.
    My setup is the N9A2 Platinum, V1.
    Bios v 1.4, 3/112/08
    Phenom X3 720
    Ultra 750W power Supply
    Seagate 500GB SATA HD
    WD 80GB SATA HD (for Photoshop scratch drive)
    My Bios is set up as follows>
    Integrated Peripherals 
      Extra RAID Controller - Disabled
      On-Chip ATA Devices
          PCI IDE Busmaster - Enabled
          RAID mode           - IDE
    OK, Any ideas?  You folk have a lot more experience with me.  Thanks for all/any help.

    Ports 5 and 6 ,the red ones ,are for the Promise Extra RAID controller ,which as per BIOS settings was turned off  ,thats why the HDD was not detected .You can use that Promise controller with HDD-s ,even if they are not in RAID config ,but drivers are required.
    Glad i could help you!

  • Cannot find the Hard Drive on Disk Utility

    I am using an iMac (mid 2010) the factory Operating System was Mac OS X 10.6.4 and updated to Mac OS X 10.9.1.
    Following a "Flashinhg Question Mark" iMac was unable to boot.
    Then installed OS X on an external HD and boot the iMac. http://support.apple.com/kb/ht5911
    iMac is working with the external Mac OS but in the "System Preferenses>Startup Disk do not show the internal Hard Drive.
    Following this issue the iMac fan is working fast and noisy.
    I tried
    1. SMC reset
    2. PRAM reset
    3. Safe Boot
    4. Boot with the external USB Mac OS X
    nothing helped me.
    Thanks in advance for any guide.

    Cornelius,
    I was in the process of running Disk Utility last night to repair permissions when it gave me a message that it could not connect to Disk Management Unit (I think that was the name) and suddenly quit. I tried again, and the same thing happened. Then, the computer froze with the spinning rainbow again, and I had to do a hard shutdown. When I tried to restart, I got a gray screen. I tried squeezing the left corner again, and after a couple of attempts was able to boot the computer. However, it froze again and had to be shutdown. This cycle happened a few more times before I decided to give it a break.
    This morning, my husband turned it on to see what it would do, and it started up normally. However, we restarted it so that we could repair the disk, and it took several tries before it could see the HDD. I tried "repair," and it seemed to work for about a minute before giving me the same error message: "The underlying task reported failure."
    My husband and I believe we have some sort of logic board problem, specifically the ATA controller. What is your opinion, and what would you suggest next?
    Thank you for your help so far!
    -Brooke
    [By the way, I find it interesting that my forum register date is 7 days after yours. : )]

  • The system cannot find my hard drive - is it broken?

    I recently updated to OS X 10.4.4 and everything was fine. But today the system froze and I couldn't do anything but press the on/off switch to quit. After that I couldn't boot the system normally. If I start from the System-DVD and open the disk utilities the Hard Drive is not displayed so I cannot check the volume. What can I do?
    G3 iBook 600 MHz 640 MB SDRAM   Mac OS X (10.4.4)  

    Hi Berndt, thank you very much for your advice. I think too it's something different and not the HD. After resetting the iBook (vram, pram, pmu etc.) and after a while waiting the system started yesterday without any problem. So I could make a backup. But this morning I had the same phenomenon - frozen Screen (only the cursor worked) and I have to reset everything again. I think I will give it to gravis for an inspection. But I don't want invest too much. A new (bigger) HD would be fine but I don't know what else could be broken and how much the components are. What do you think?
    Ronda. I bought my iBook with an OEM Version of diskwarior 2.1.1 which doesn't work with OS-X. I looked at Alsoft but there is no download update available - I have to buy an Upgrade tp Version 3.0 for 39 quid and it takes 3-4 weeks shipment. Do you know an alternative?
    G3 iBook 600 MHz 640 MB SDRAM   Mac OS X (10.4.4)  

  • Portege M400 - Windows XP cannot find the hard disk drive

    Hi,
    Ive got a Portege M400 to which im wanting to start a fresh, I never had the tablet XP CD so im trying to install using a XP Pro disc but everytime I get no hard drive can be detected and I tried a another Home edition disc also.
    Ive searched for SCSI/ SATA drivers but can only find RAID drivers to which are no good for me,
    Hopefully someone can help me out
    Thanks

    Hi wacksonjackson,
    Why these RAID drivers are not good for you? Windows XP requires RAID drivers if your notebook has RAID controller and there is no other option to install XP from a normal Windows XP disk. So download the RAID drivers on official Toshiba website. Either you create a new installation disk with RAID drivers using freeware tool nLite or you copy the drivers on an external USB FDD and load them during XP setup.
    Also check similar threads here in forum. You will find hundreds of similar threads about SATA and RAID drivers.
    Check this!!!

  • Pavilion a6412p cannot find seagate hard drives.

    Get disk not found msg at bootup.  Drive hooks up to other PC via USB and is OK.      Cannot boot to update bios via sp40966.exe    Any way to fix bios from bootable CD?

    Hello nashdavea,
    I understand you’re getting disk not found on boot.
    I see you have tested the hard drive and it worked fine. Looking at your motherboard it looks like you have about 6 sata connections total. Have you tried any of the other available connections?
    Also if you’re unable to load into bios it sounds like it could be a system board issue.
    Try those other connections and let me know if the results change or stay the same.
    Thanks.
    Clicking the White Kudos star on the left is a way to say Thanks!
    Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

  • I Need to Reinstall iWork (specifically Pages) but cannot find Install Disc.

    I had the most recent version of Pages, but bought it on disc before the App Store came around.  Now I need to reinstall and I cannot find the original disc. The App Store does not recognize that I own it.
    Do I have any options to reinstall or am I doomed to purchase it all over again through the App Store?

    If you can't find the disk or restore Pages from backup, you'll need to buy it from the Mac App Store.
    (72085)

Maybe you are looking for

  • LSMW for Customer master text upload

    Hi I would want to upload the customer master text using LSMW. I see a message type /DSD/HH_CUSTMASTEXT (Customer master additions) being available. has anybody used this for text upload?? I am not sure how it works, i dont see the provision to enter

  • IPhoto is cropping images I want to print

    I am trying to print multiple (4) of same photos to a page--IPhoto feels it must crop the photo, rather than scaling the whole picture down to the smaller size. IMHO, the print functionality of IPhoto is not very flexible, and in no way intuitive. Th

  • MeetingPlace Express 2.1.1.2 Backup

    Hi, I was trying to take the backup of MeetignPlace Express 2.1.1.2 but I got the following error, I was trying take the backup and archive it. =========== Script archive.sh inited at 2010-05-05-08:46 ========== === Archive started = Copying /db/back

  • Insert a JComboBox in a cell of JTable

    Hi, I have 3 comboboxes having different items, I want to add them in different rows of a JTable. I can add a JComboBox into a column using DefaultCellEditor but it will show either all items or the Items in the last ComboBox (if I call removeAll). W

  • Migration from weblogic 9.2 to 11.g

    Hi I am trying to migrate from weblogic 9.2 to 11.g and I am getting the follwoing error : 'weblogic.kernel.Default (self-tuning)'] - java.lang.NoSuchMethodError: org/apache/commons/pool/impl/GenericObjectPoolFactory.<init>(Lorg/apache/commons/pool/P