OS won't load after Erase & Install

my computer decided to take a crap the other day, and after trying to restart a few times, only to have it just stop on a blue screen, i decided to re-insall the OS. I tried doing an archive and install first, but both times i got a message saying that there was an error and i shouldl try again. I then decided to do an erase and install, and it gets through the installation process with disc 1, but without asking for disc 2, it restarts, only to stop on the gray apple screen for about 10 minutes, at which point it restarts again and gets stuck in this loop. If i catch it at a restart point, i can boot from the disc again, but then i'm back at the install screen. Trying to quit the installer and change the boot disk to the internal drive ends up back in that loop, so there's obvioulsy an issue with the installation not being completed correctly.
This is the second time i've tried the Erase & Install with no success and the same result. Any thoughts? Perhaps it would work if i installed it on another drive? i have one coming in a few says...
thanks

What computer model are you installing on? Are you trying to install Tiger or Leopard? Have you tried re-prepping the drive?
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.)Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.

Similar Messages

Zenworks won't load after NW65sp5 install

I'm not sure if this should be posted here or elsewhere...its a java
problem now.
Server is NW6.5SP3 running Zenworks 4. I installed the above service pack
and at the end errored. After reading a similar item in the forum I
renamed the java folder to something else and reinstalled the service pack
which completed this time. Now however, Zenworks will not load due to java
errors.
The two classes that won't load correclty are
..desktop.inventory.servercommon... and
autowsmanagement.wsremoval.removeWorkStations.
Thanks in advance.

Fredr,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Onboard audio modules won't load after Skype install on 64b Arch

Hi,
I've a fully updated Arch 64b/KDE 4.5.2 (new PC).
My motherboard has a Realtek ALC889 Audio controller, and, in addition I have a Radeon 5600 graphic PCIe card with HDMI output.
I have the on-board audio controller enabled at the BIOS.
Initially, my audio worked fine, till I installed (from Arch repositories) Skype along with required 32b libraries.
My current status, after reboot:
The 889 module is not loaded (see below), only the one included in the graphic card.
When logging in KDE, I do hear the sounds.
Although Skype loads and logs-in fine, I can't hear Skype's test sounds nor does it capture the microphone connected to my motherboard back microphone plug. (Skype options offer ONLy Pulse Audio both for output and capture).
Both alsa-utils and alsa-oss are installed.
Please advise how do I restore full Audio capabilities (along with functional Skype).
Thanks!
I've tried to follow the Alsa wiki of Arch with the following results:
lspci | grep Audio
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
01:00.1 Audio device: ATI Technologies Inc Redwood HDMI Audio [Radeon HD 5600 Series]
ls -l /sys/module/snd/holders
total 0
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_hda_codec -> ../../snd_hda_codec
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_hda_codec_realtek -> ../../snd_hda_codec_realtek
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_hda_intel -> ../../snd_hda_intel
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_hwdep -> ../../snd_hwdep
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_mixer_oss -> ../../snd_mixer_oss
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_pcm -> ../../snd_pcm
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_pcm_oss -> ../../snd_pcm_oss
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_seq -> ../../snd_seq
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_seq_device -> ../../snd_seq_device
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_seq_oss -> ../../snd_seq_oss
lrwxrwxrwx 1 root root 0 Oct 6 12:05 snd_timer -> ../../snd_timer
I've tried to modify my /etc/modprobe.d/modprobe.conf to the following but, during boot, noticed a message saying modprobe ignores the option due to an error. The same happened also after omitting the "index=0" per the Wiki's recommendation.
# /etc/modprobe.d/modprobe.conf (for v2.6 kernels)
options snd-pcsp index=2
# disable autoload of ipv6
alias net-pf-10 off
# added by miki
options snd_hda_codec_realtek index=0
options snd-pcsp index=1

p0x8 Thank you for the response, yes the host is Arch Linux. I am running the most current version of Virtual Box v4.2.8-1.
Now, with what you are saying, what I am missing. How do I get the VMs to work properly. So far, I have been able to get the Network up and running via each VM, Mouse and Keyboard integration is working. Also was able to get USB devices working as well. But my screen resolution is garbage for all 3 VM's. In doing some other reading, I noted where within the VM (Windows XP to be specific) there will be an icon on the lower right corner stating Oracle VM Virtualbox Guest Additions. This will also display a VBox system trey for lack of a better word on the bottom where you can attach devices and what not. That is what I am trying to get working on all 3 of my VMs.
Thank you again, and I should have paid more attention to detail as that section of the Wiki does say "Arch Guest" and not "Arch Host"
Edit: One thing I wanted to add. In reading the wiki it states:
Guest additions disc The virtualbox package also suggests installing virtualbox-guest-iso on the host (Arch Linux) running VirtualBox. It is a disc image that can be used to install the guest additions onto guest systems. Make it available to the (running) guest by going to Devices and clicking "Install Guest Additions... Host+D". Then run the guest additions installation from inside the guest.
I don't see the "Devices" option in order to run this. I have the virtualbox-guest-iso package installed in Arch, but when running the VM, I don't see a "Devices" option.
Last edited by ichase (2013-03-15 14:27:31)

Lightroom 5 won't load after 30 day trial of Lightroom3 error.

I tried the 30 day trial of Lightroom 3 that I got with the Photoshop Elements 10 when I got my new computer. The Lightroom loaded one picture and said I had an error and would try to find a solution. I bought Lightroom5 and tried to install it and it keeps going back to the error of Lightroom 3 trial. I tried to delete all programs associated with Lightroom and reinstall, but nothing happens.

it just reads "Lightroom-Opening Catalog:New Years Day 2014 031.JPG.Ircat assertion failed!
New Years day 2014 is a folder and 031 is the picture in the folder that I tried to enhance in the 30 day free trial of Lightroom 3. I bought Lightroom 5 from B &H and it appears to be hung up on the Lightroom 3 trial.
kglad <[email protected]> wrote:
kglad http://forums.adobe.com/people/kglad created the discussion
"Re: Lightroom 5 won't load after 30 day trial of Lightroom3 error."
To view the discussion, visit: http://forums.adobe.com/message/6048439#6048439

My apps won't load after updating to iOS4.3.2. What to do?

My apps won't load after updating to iOS4.3.2. What to do?

Yes, I tried that (thanks for the suggestion, though!). In my music app, when I click on certain songs, the screen moves to try to start the song, but then it bounces back to the menu screen without playing the song. On many albums, when I click on the first song, a song about halfway through the album will start to play rather than that first song. My other apps seems to be fixed, but not the music function.

Old emails won't load after upgrade to Mountain Lion

old emails won't load after upgrade to Mountain Lion

See if anything in here will fix it:
1. Hold down the Command and Option keys as you click the iPhoto icon.
The Photo Library First Aid window opens:

HELP!!!! Aperture 1 won't open after I installed Snow Leopard.

Aperture 1.5 won't open after I installed snow leopard. Why is it not working?

Because it's incompatible. You need to upgrade to version 2.1.4 or newer.
(56089)

Bootcamp Wont Load After Yosemite Install

Loner T,
My bootcamp does not load after Yosemite install.
Thanks

This is the first part of the recovery procedure. In your case, you have two OS X versions, so standard layout is not usable.
Please install GPT Fdisk (aka gdisk) (http://sourceforge.net/projects/gptfdisk/) if you have not done so yet.
You need to use the following steps. If you see any error messages during the following steps, please stop and post back here with the error message. The following steps have values from your Testdisk output (and you can verify) in Steps 7 and 8.
Rebuild GPT5 using start/end offsets
Sudo gdisk /dev/rdisk0
P (print the full list of parts)
D (delete)
5 (part 5)
N (new part)
5   (part 5)
841717760 - Start offset in bytes (start point for Bootcamp part)
+135055353 (Size offset as opposed to End offset)
0700     (Windows part type)
P           (print list of all parts just to see what changes will be made)
W         (Write the new GPT)
Y           (Yes! really write the new GPT)
This will delete and re-write the GPT partition info for /dev/disk0s5.
Reboot. Test that you can see the Bootcamp volume in Finder and see files in the Bootcamp volume.

I tunes store won't load after 11.1.3 update

I Tunes store won't load after i updated itunes . Its the 11.1.3 update

Hello Papamax,
And welcome to Apple Discussions!
Have you ran an iTunes *Network Diagnostics Test* yet? If not, use the steps provided in this Apple support document to do so, and then paste your results here.
http://support.apple.com/kb/HT3204
Also, try temporarily disabling McAfee and see if that helps. And make sure you have allowed iTunes through its firewall, by using the instructions provided in this article.
http://www.technipages.com/allow-program-access-through-mcafee-personal-firewall .html
And lastly, see if any of the troubleshooting steps provided in this Apple support document can assist you.
[iTunes for Windows: iTunes Store connection troubleshooting|http://support.apple.com/kb/ht1527]
B-rock

"General" in Settings won't open after I installed the iphone 4.0 upgrade.

"General" in Settings won't open after I installed the iphone 4.0 upgrade. Any ideas?

Have you tried to reset? Hold off button and home button together until Apple apears.

Safari won't load after 10.3.9 re-install

Here is my history:
-Tried to update OSX10.3.9 with combo download
-Upon re-start machine gets stuck in start up during boot, stuck on blue screen
-then re-start with software install & restore DVD
-go to disk utility, perform Repair Disk in First Aid
-result:diagnosis 'volume header needs minor repair' then 'volume repaired'
-First Aid done it's job I think, on re-start same problem though, stuck during boot.
-Re-boot again with DVD disk, this time perform re-install 10.3.9 archiving all.
-Great, machine starts but Safari won't load.
- I look for /System/Library/Frameworks/WebKit.framework/Versions/A/Webkit as advised on old post on this forum.
- I can't find it on updated system, however it is in my 'Previous System' Folder, I try to copy it over but won't let me because 'frameworks cannot be modified'
Any advise out there about getting Safari started again, I'm dying here without it, got all my links there. Every other programs works fine. Heard something about 'double boot', should I have changed some settings before re-install? Can some one guide me here. Had this baby 3 years, no system problems ever, should never have tried to update, feels like I'm in PC-land arrrr...
Any help hugely appreciated!!!
powerbook G4 Mac OS X (10.3.9)

Welcome to Apple Discussions
Strange the computer hung during the upgrade. Never a good sign. While the computer was upgrading, were you using it for any other task? Was their a power interruption?
When you ran disk repair from Disk Utility, did you rerun the repair function until it showed no errors. If not, do this step again, then on the restart to your main system, repair permissions using Disk Utility in your Utilities folder.
If still no cooperation from Safari, have a look here for guidance regarding a Safari reinstall in Panther. Ignore the 10.4.4 update suggestion. In addition to the various suggestions, make sure you remove Safari from your Applications folder, putting it in the trash.
The installer will download an earlier version of Safari. Once installed, you'll need to upgrade to the final version - 1.3.2. To do so, first install Safari 1.3.1. Then, install Safari 1.3.2. Once complete, "repair permissions" using Disk Utility in your Utilities folder.
Post back with results.

Computer won't load after Install

Hello,
Just this afternoon I had some installs waiting so I allowed them to go through and restarted after the install as usual. After restarting though my computer was sluggish and wouldn't respond to opening my printer bar, or my command to shut it down. My husband hard-booted it and this time when loading it got stuck at the white apple screen and never went any further. The fans were going overtime like it was overheating so we shut it down, took it apart and cleaned it because it hasn't been cleaned in several years.
This did not fix the problem though so I tried hitting CMD+s when it loaded to get the DOS screen and fix any install errors that may have happened. This did not work either though. The DOS screen never came up. All I ever get is the white apple screen that never goes any further. Does anyone have any other ideas for things I can try!?

Hi Melime, and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
The usual reason why updates fail or mess things up, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates.
May even need to do an Archive and Install if you have room on the HD, but saves all your files and gives a new OS...
http://docs.info.apple.com/article.html?artnum=107120
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.
If all the above fails, then it appears to be time for aAn Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.

IPhoto won't open after new install and restore of back-up

Hi guys
My hard drive just died (for the second time in 6 months!) so I have just gotten the computer back with a new drive. I did a new install of Tiger from my original install CDs, did the download thing to get all the updates, and ran a "restore" from my external drive using iBackup (http://www.grapefruit.ch/iBackup//index.html) to restore all my previous system settings, documents, etc. So far this seems to have worked well, a couple of 3rd party applications didn't re-install - specifically Neo Office and WiFind - but I was able to manually install those and everything seems to be working fine.
Except iPhoto. It won't open. When I click the dock icon it bounces once and does nothing. No little arrow under it or anything. Nothing at all happens when I click the icon in Finder (in the Applications folder). When I searched it in spotlight it told me there was a file called iphoto.crash.log, so I went and had a look at that hoping it would tell me the problem, but I don't understand it. I'm not particularly good at the behind the scenes stuff with computers.
Wondering what I should do now - if someone can perhaps interpret the log file and find the issue if that would help, or if I should uninstall and re-install iPhoto by itself (and if so, how?), or if there is something else that may be causing the issue. I noticed there are a few files relating to it when I search with spotlight but I don't know which of them might be relevant. I could post a screenshot if that is allowed, or post the log file if it would help?
Thanks in advance for any advice or help!
Regards,
Chloë

400 Updates???
Did you Repair Permissions before & after each one?
The usual reason why updates fail or mess things up, or things don't load/run, is if Permissions are not fixed before & after every update, with a reboot... you may get a partial update when the installer finds it doesn't have Permissions to change one obscure little part of the OS, leaving you with a mix of OS versions.
Some people get away without Repairing Permissions for years, some for only days.
If Permissions are wrong before applying an update, you could get mixed OS versions, if Directory is the slightest messed up, who knows!
If many Permission are repaired, or any Directory errors are found, you may need to re-apply some the latest/biggest updates again, or even do an A&I if you have enough free disk space.
The combo update for PowerPC-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
The combo update for Intel-based Macs...
http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
Repair Permissions before & after re-install, then reboot again each time.
If all the above do not resolve the problem, then it's time for an Archive & Install, which gives you a new OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space...
http://docs.info.apple.com/article.html?artnum=107120
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

IBook G4 won't load after latest security update, repair doesn't work?

Hi I had the same problem as someone else in this forum:
"Last night I saw that my ibook G4 wanted to do a security update. I told it to do it, and the ibook has not started since. It reset itself after downloaded, but it just stays on the booting up screen, never actually booting up so I can use it. After about two hours of trying to boot up, I turned it off, and on again, and it still wont boot.
I really need suggestions as how I can fix it. Thanks
ibook g4 Windows 2000
Carolyn Samit
Posts: 8,431
From: Alameda CA Bay Farm Island
Registered: Aug 5, 2005
Re: G4 wont boot after latest security upgrade
Posted: May 22, 2009 2:51 PM in response to: voiletmay
Click to reply to this topic Reply email Email
HI,
Ok... you need to boot from your install disk.
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
If you cannot boot from your install disk, try booting in Safe Mode
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
If you have the original hard drive in this iBook, it was probably a 60GB drive? When you can do this, check to see how much available disk space there is.
Right or control click the MacintoshHD icon on your Desktop, then click: Get Info. In the Get Info window, click the discovery triangle so it's facing down. You will see; Capacity and Available Make sure you have 10% available disk space, 15% is better. Not enough available drive space can cause issues like you are experiencing.
Carolyn "
I tried restarting it after the repair (there were some things to repair and I tried to repair twice just to make sure it didn't miss anything) but it still won't load. It says its starting the OX system, but when the blue bar reaches the end, it doesn't do anything from there. I also left it on for hours and it did nothing. My mousepad still lets me move around the mouse, the caps lock key still lights up, as the num lock key. I tried safe mode but that won't load either...any other suggestions?

*" I also left it on for hours and it did nothing. "*
Your iBook needs to go in for repairs.
Carolyn

CFB won't load after update 1

I'm running CFB plugin on Eclipse 3.5.1 on Win 7 x64. I purchased CFB right after update 1 came out, restarted eclipse, entered my key, updated the software, restarted eclipse using the -clean option, and everything worked great. I've been using it for the past week. However, I just restarted eclipse for the first time since I've updated, and it won't load CFB. I get the following error:
Could not open the editor: No editor descriptor for id com.adobe.ide.editor.CFMLEditor
org.eclipse.ui.PartInitException: No editor descriptor for id com.adobe.ide.editor.CFMLEditor
    at org.eclipse.ui.internal.EditorReference.createPartHelper(EditorReference.java:598)
    at org.eclipse.ui.internal.EditorReference.createPart(EditorReference.java:462)
    at org.eclipse.ui.internal.WorkbenchPartReference.getPart(WorkbenchPartReference.java:595)
    at org.eclipse.ui.internal.EditorAreaHelper.setVisibleEditor(EditorAreaHelper.java:271)
    at org.eclipse.ui.internal.EditorManager.setVisibleEditor(EditorManager.java:1417)
    at org.eclipse.ui.internal.EditorManager$5.runWithException(EditorManager.java:942)
    at org.eclipse.ui.internal.StartupThreading$StartupRunnable.run(StartupThreading.java:31)
    at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35)
    at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:134)
    at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3855)
    at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3476)
    at org.eclipse.ui.application.WorkbenchAdvisor.openWindows(WorkbenchAdvisor.java:803)
    at org.eclipse.ui.internal.Workbench$28.runWithException(Workbench.java:1384)
    at org.eclipse.ui.internal.StartupThreading$StartupRunnable.run(StartupThreading.java:31)
    at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35)
    at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:134)
    at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3855)
    at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3476)
    at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2316)
    at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221)
    at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500)
    at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332)
    at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493)
    at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149)
    at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113)
    at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194)
    at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLau ncher.java:110)
    at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.jav a:79)
    at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368)
    at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
    at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
    at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
    at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
    at java.lang.reflect.Method.invoke(Unknown Source)
    at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559)
    at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514)
    at org.eclipse.equinox.launcher.Main.run(Main.java:1311)
Please help!!!

To fix this, I launched eclipse again with the -clean option. CFB asked me to enter a key (which I already had done before I applied update 1). I entered the key again and CFB loaded.
I had already run eclipse with the -clean option after installing CFB update 1. I double checked to make sure I didn't have to do this each time I restarted eclipse - I quit eclipse and launched it again, and CFB loaded. Everything seems to be working okay now.

OS won't load after Erase & Install

Similar Messages

Maybe you are looking for