OS X 10.2 w/ Airport Card Connecting to Extreme Base Station

Hey--
I'm on a G3 Powerbook (w/Firewire) running OS X 10.2 and I installed an Airport Card and I'm trying to connect to a new Extreme Base Station-- and PB can't see the Base station in the Airport Utility. Although my PB does receive the signal from the base station.
I've tried:
- Resetting the base station
- Loaded Airport 2.1.1 software update
- a million configurations
- yelling at it...
The airport card does work, because it connected on another wireless system.
Can someone help me with the definative fix?
Mike

Welcome to the discussion area, stacidesign!
First, you have verified that the PC can connect to another wireless network, correct? If it can, then that tells you that the wireless card is functioning correctly.
You'll have better luck connecting to a newer wireless router if you are able to update the PC to Windows XP SP3. Have you tried this?
It's also possible that the wireless card in the PC can connect to a 802.11 "b" or "g" network, but not to an "n" network. To check that out, you need to use AirPort Utility - Manual Setup to make a change in the radio mode of the AirPort Extreme.
Click the Wireless tab below the row of icons
Hold down the option key on your Mac while you click on the Radio Mode selection box
Write down your current settings so you can return to them later if needed
Select this Radio Mode...+802.11n only (5 GHz) -- 802.11 b/g+
Keep the Wireless Security set to "None" temporarily
Update to save changes and allow 30-40 seconds for the AirPort Extreme to restart
Restart the PC
See if the PC can connect now
Please post back on your results
Message was edited by: Bob Timmons

Similar Messages

  • Adding an Airport Express to an Extreme Base Station

    I have an Airport Extreme Base Station and it has been operating for several months, I decided to add an Airport Express to extend the range and it appeared that it was a simple process. NOT. The Express instructions indicated that when downloading the software to follow the instructions on setting up a network but it will not get that far in that I get an error message telling me I have a newer version of I Tunes and it stops the install. I have gone through the tech support pages here and am at a loss on how to get this connected. Can anyone help provide me a step by step method to do this? Thanks

    On this same topic;
    We have a new Extreme base station that connects 1 MBP, (wirelessly), 1 HP Laptop (wirelessly) and 2 PC (via ethernet) to the internet.
    All of the computers can see and use the Extreme base station and the printer connected to it via USB.
    We also have an Airport Express that the two laptops can see. This has a printer connected to it as well via USB. (both are new Canon printers and all of the software for each, and their drivers are loaded on all computers).
    Both the Extreme and Express have a steady green light, their own names and are set up on the same network.
    Though my MBP can see both the Extreme and Express, neither "see" each other as far as I can tell. And, the printer connected to the Express cannot be seen in either Bonjour Printers, or anywhere else.
    Also, in order to "attempt" to find the printer connected to the Express, I have to disconnect from the Extreme Base Station and connect to the Express.
    How can I get the printer (connected to the Express) to show up in my pick list of printers WITHOUT having to disconnect from the Extreme and connect to the Express. Also, how can we get the Express to be connected to the internet via the Extreme?
    All searches here and documents I have poured though do not address this issue and we'd really like to get this straightened out. I am willing to take a lot of time to do this, but do it right.
    Can someone please help me with this?
    Thank you in advance,
    ~ J

  • PC seeing but not connecting to extreme base station

    Hello! I've searched many forums and done some of the suggested things in some posts related to my topic, but can't find the exact topic that is afflicting me at the moment...
    I recently purchased a gigabit dual-band Airport Extreme. I have two computers in my house that connect to the internet just fine, a mac pro and a older laptop running windows XP something...
    We are wanting to hook up a desktop PC running windows XP SP2 (I believe) and the wireless-g card (linksys) can "see" the network, but for some reason can't connect. Even if I turn the security completely off, it won't connect. All suggestions I have seen before, people have been able to connect when the network security is off. This is not the case for me.
    Any suggestions?

    Welcome to the discussion area, stacidesign!
    First, you have verified that the PC can connect to another wireless network, correct? If it can, then that tells you that the wireless card is functioning correctly.
    You'll have better luck connecting to a newer wireless router if you are able to update the PC to Windows XP SP3. Have you tried this?
    It's also possible that the wireless card in the PC can connect to a 802.11 "b" or "g" network, but not to an "n" network. To check that out, you need to use AirPort Utility - Manual Setup to make a change in the radio mode of the AirPort Extreme.
    Click the Wireless tab below the row of icons
    Hold down the option key on your Mac while you click on the Radio Mode selection box
    Write down your current settings so you can return to them later if needed
    Select this Radio Mode...+802.11n only (5 GHz) -- 802.11 b/g+
    Keep the Wireless Security set to "None" temporarily
    Update to save changes and allow 30-40 seconds for the AirPort Extreme to restart
    Restart the PC
    See if the PC can connect now
    Please post back on your results
    Message was edited by: Bob Timmons

  • Airport card connected but safari not connected to internet

    Running os 10.4.1 on IMAC g5 with airport card.
    i am having some wireless network issues. when i try to connect to the linksys router that my airport card locates it tells me that i am connected to the network; but when i try to load a page in Safari it tells me that i am not connected to the internet. Internet Explorer gives me the same message.
    i have been able to test my airport card by logging into another (neighbor's) network (just for testing). it received DHCP from that router and assigned a 198.162.x.x. IP address for my computer. i originally had the same issue as far as being connected but safari wouldnt open web pages. i manually plugged in DNS numbers 208.67.222.222 and 208.67.220.220 from OPEN DNS.com and Safari instantly loaded web pages.
    when i try to do the same on the linksys network my airport card connects but Safari once again will not connect to the internet. I am receiving a DHCP IP address automatically from that router but cannot connect to the internet...
    PLEASE HELP ME (it's driving me crazy!)

    Oh man... since my last post (all of 15 minutes ago) my iMac now cannot connect to the network at all. The network status menu widget shows it as being connected (sometimes), but it can't actually connect to anything.
    Just as an experiment, I turned off MAC address filtering on the base station. Didn't help.

  • Connect AirPort Extreme Base Station to air card

    How do you connect AirPort Extreme Base Station to Verizon Air Card?

    Sorry, but the Air Card cannot be used with the USB port on the AirPort Extreme because that port will only work with a hard drive and/or a printer.
    Suggest that you check with Verizon to see if they have an adapter or wireless router for the Air Card that will provide an Ethernet signal to the AirPort Extreme.

  • Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network  with  newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

    My Power Book G3 Pismo with an Airport wireless card  running Mac OS X 10.4.11 will not connect to my new Airport
    Extreme Base Station using WPA Personal/WPA 2 Person encryption.  The Airport firmware is version 9.52.  From
    posts I've read online at different places indicates the Airport card should support the WPA encryption.  Perhaps the problem
    is the Base Station is using a combination setting and the fault is in the base station?
    Thanks for any suggestions

    Perhaps an inexpensive usb wireless adapter would work as well?
    This is probably the simplest way to get the G3 connected to the wireless network.
    I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
    The new AirPort Extreme is broadcasting a wireless signal.
    A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable. 
    This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
    I do have an old Linksys Wireless G router.  I wonder if that would work?
    In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

  • Can an original Airport card connect to an Airport Extreme base station

    I have an old iBook G3 10.3.9 with an original Airport card (System Profile says "Wireless Card Firmware Version: 8.70"). This computer/airport card connects fine with an old Airport Graphite.
    But it will not connect with my main Airport Extreme 802.11n (1st Generation), running in 802.11n (802.11b/g compatible) mode. This Airport is using WPA/WPA2 Personal wireless security. This Airport Extreme works fine with my other computers and devices.
    Does anybody know, offhand, whether it is just a setting, or is this completely unworkable?
    Thanks in advance for any input.

    I cannot remember all the details regarding the older iBooks, but suspect that the wireless card and possibly the operating system that you are using on the iBook cannot support WPA/WPA2 wireless encryption.
    As a test....
    Temporarily turn off the wireless security on the 1st Gen AirPort Extreme, then see if the iBook can connect to the wireless network that way.
    If it can, this tells you that the wireless is at least working on the iBook....but it cannot connect to the WPA/WPA2 network.
    The solution might be to use a USB wireless adapter that can handle the higher encryption levels, or connect the iBook using Ethernet.
    If the iBook still cannot connect when security is disabled during the test, then the iBook has additional issues that you may or may not wish to pursue.

  • IBook G3 optional airport card connection

    I have a 2003 iBook G3 with an optional airport card which doesn't connect to a new airport extreme base station.  Is it just too out-of-date to make the wifi connection to new base stations?  I can connect by ethernet.

    The article https://support.apple.com/en-us/ht2594 contains information about the requirements for a connection to a base station with WPA security (if this is what you are using). However, although a plain AirPort card (802.11b) is mentioned there, it appears to be unclear whether it in fact is possible to use such a card with WPA. You may want to study posts in the AirPort communities to begin with.
    You may also (temporarily) want to switch off encryption (or use WEP) at an available base station (router) for a test. If one can connect then, you know that the problem is related to security settings.
    One alternative could possibly be to use a USB wireless adapter (with WPA/WPA2 capabilities), but these do usually require at least Mac OS X 10.3 (often higher). So, make sure that driver software is available for your system before you buy.
    Another option (albeit less portable) could be to connect a wireless Ethernet bridge (such as Netgear WNCE2001 or Linksys WET610n) to the Ethernet port. This kind of adapter does not need special drivers, and can thus be used under almost any operating system.
    Jan

  • Wirelessly Connecting HP Laserjet P3015 to Airport Extreme Base Station

    Hi, I just purchased a new Airport Extreme Base Station, and was able to establish an internet connection to it.  I'd like to find out if it's possible to connect the HP Laserjet Enterprise P3015 to the Extreme, wirelessly rather than via a USB Cable.  I've looked at the HP page for this printer, but I'm baffled by all the lingo.  I believe it's a newer model of HP printer (or maybe it isn't?) but I bought it new from HP recently.
    http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=S upportFAQ&lang=en&cc=us&docIndexId=64178&taskId=101&prodTypeId=18972&prodSeriesI d=3815797&printver=true#10
    Is there a term for the type of printer that can be wirelessly connected?  Should the printer, by default, give off a signal that I can pick up?  I don't see anything popping up in Airport Utility 6.3
    I'm using OS10.7.5 by the way.
    I'm off to post a message on the suitable HP forum (if I can find it ) but I'm so used to the Apple Community knowing what's what, that I was hoping that some kind soul here might just have experience with this.
    Thank you.
    PS.  From what I can understand from the "Trouble-shooting FAQ," wireless printing is possible, but I just don't see an option for syncing it up with a MAC?  Maybe it only works with Windows?

    wuzradioman
    I don't see where the P3015 printer is wifi capable.  Therefor, you cannot use wifi to directly communicate with it.
    Thanks for the reply Wuzradioman.  I dug around (several) of HP's sites and it looks like the info was slightly different for the same printer listed on both the Home and Business sites.  I did find a link on a 3rd HP page (which I've since misplaced!) that indicates that the P3015 requires a wireless card to be installed.  But when I clicked the link for "accessories and additional hardware" a link to the card was nowhere to be found.  I'll try to dig up that link in the event that some other poor soul has the same printer and a similar question.
    Vernon Alexander
    I find the HP printers (they're called wireless printers by the way) to be cumbersome to connect wirelessly. there's a lot of manual work involved that can be time-consuming. For example, I found it  incredibly irritating to enter the  wireless access passcode.
    Thanks for the reply.  After talking to some other people, this seems to be the consensus on wireless printing.  I guess there's a reason, esp. in enterprise environments, that printers are often hard-wired.
    Bob Timmons
    you can run an Ethernet cable over a much longer distance than a USB cable, so Ethernet might be the best option, and the one I would prefer.
    As far as wireless, If you connected an AirPort Express to the printer and disguised it near the printer, then you could locate the printer anywhere you want and have it connect using wireless to the network.
    Instead of installing a wireless "card" inside the printer, you use an outboard device to accomplish the same task.
    Thanks Bob.  I did end up hooking up via a Cat-5e cable from printer to Airport Extreme base.  Previously, I had the printer hooked up via USB cable (at a shorter distance) to my Airport Express, which the Extreme now replaces.
    Unfortunately, I can't seem to get the HP Laserjet P3015n printer recognized after having connected it via Cat5e cable to the Airport Extreme.   1) there's still somethign about it being attached to the old Airport Express (which is now used to extend my network.  2) The P3015 is identified as a P3010 - which is a carry-over from when I had originally set up the printer on my (then) main base station which was the Airport Express.  I didn't (or rather "stopped") questioning the fact that the P3015 was recognized as a P3010 just because it was the only way I could get the printer to be recognized at the time.\\
    But I suppose this new challenge merits a separate thread, which I'll start after I do a search of the support forums.  Maybe there's something obvious I'm not doing to get the printer sorted out.

  • Can't get PC laptop to connect to Airport Extreme base station. Help!

    I've spent a lot of quality time on the phone with support staff at Apple, Earthlink, and Netgear. Now I turn to you fine folks.
    I have an Airport Extreme base station. My G4 is connected to the base station via ethernet, and that works fine. My problem is with the wireless networking with our Dell laptop running Windows XP SP2. Wireless card is a Netgear WG511 with updated firmware. I've configured the network on the PC end using the Netgear Smart Wizard, rather than Windows (I don't know if that makes any difference).
    Smart Wizard says the PC is connected to the network, and says that signal strength is excellent. However, there is no connection. I've tried pinging, but get no reply.
    The status bar in the Smart Wizard window switches every 2 seconds from "Connected" with excellent signal to "Searching" with virtually no signal. The log shows that it's constantly connecting to and disconnecting from the network.
    I've gone over IP and MAC addresses and whatever other settings I could check with all of the respective phone support people. I'm using WPA/WPA2 Personal security, and have double-checked the 13-digit password on both ends. I'm connecting using PPPoE, per Earthlink's settings.
    This is maddening! Any suggestions? I'd really appreciate it.
    G4   Mac OS X (10.4.10)  

    See if iFelix's suggestions work for you.
    http://www.ifelix.co.uk/tech/1000.html
    Remember all the smart wizard stuff is strickley for PC Hadrware and Software and does you no good at all with a Mac.
    Don

  • Connect to Linksys Cable Gateway via AirPort Extreme Base Station?

    Thank you in advance for any replies.
    I have the following new setup:
    A G3 Blue tower running OS X 10.4.10 is successfully connected to the internet via a Linksys WCG200 Cable Gateway connected to RCN's cable internet service. The WCG200 unit has wireless capacity though it's connected to the G3 tower via ethernet cable.
    A second Mac (G3 iMac DV running OS X 10.4.10) is in another room in the office. I'd like to set it up with internet by wirelessly connecting with the existing WCG200 unit using an Airport Extreme Base Station (AEBS) I've recently acquired. To ensure a smooth process, I reset the AEBS to factory settings and installed the AEBS software (version 4.2) onto the iMac DV. Finally I plugged in the AEBS into the iMac DV using an ethernet cable plugged into the AEBS's WAN port (AirPort Admin Utility advised me to do so).
    That's the hardware configuration. Working out the software and configuration details is proving 'niggly'.
    First, I used the AirPort Setup Assistant to configure the AEBS. I told it to Set up a new Base Station, then to set it up as connecting to the internet using a Cable modem (the top option of two—the second was to set it up with internet through a LAN). I set up the name and passwords for the Base Station and had the utility configure the AEBS accordingly.
    No internet connection occurred. I tried using the Internet Connect utility in the Applications folder, but no button or visible option for connecting via AirPort appeared, as the Setup Guide indicated it should, only a button for a VPN appeared.
    I called Apple and asked whether it was even possible to connect to the internet using the AEBS talking wirelessly to the WCG200 unit. A tech told me it could be done by going into the AirPort Administration Utility, going into Configuration, clicking on the WDS tab and inputting the MAC address for the WCG200 unit, then going into the Airport tab and typing in the channel that the WCG200 is using. Note that the WCG200 unit has 3 MAC addresses listed; one each for “modem MAC address,” “WAN-MAN MAC address,” and “WAN-DATA MAC address”. I used the “modem MAC address.
    The Apple tech added that it might need further tweaking, but that Apple couldn’t provide this tweaking and that I might check various forums if need be.
    I followed the Tech’s advice, at which point the utility informed me that it couldn't use DHCP or NAT with this setup’ and to make sure that the "Distribute IP Addresses" checkbox was deselected under the Internet tab. This I did, but it was already deselected. I told the utility to update the AEBS accordingly, and restarted everything, including the 2 Macs and the WCG200.
    Result:
    No connection.
    Tried it again with the Ethernet plugged into the AEBSs LAN port, still no connection.
    Help! Can’t I get the AEBS to even see the WCG200? I know wireless is properly functioning in the WCG200 because another user with a Windows laptop connects to it wirelessly. The Mac Tech also mentioned that this could be relatively easy with an AirPort Express piece of hardware (Card? Base station?) but that it would be difficult with the Airport Extreme Base Station.
    At this point we’re willing to spend $100 on getting this up. What would be our best option in terms of equipment, or can connectivity be accomplished with what we have?
    Thanks again,
    skyheart

    skyheart, Welcome to the discussion area!
    In theory using WDS would provide what you need.
    In reality the Linksys device is not compatible with Apple's WDS and therefore this will not work.

  • Using Airport Extreme Base Station As A Wireless Card?

    Hi,
    I don't know if this is even possible but here's what I'd like to do:
    I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station. So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
    Here's my real question:
    I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
    I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
    If this is possible, how can I do it?
    Thank you in advance for any help with this.

    Ernest Lohrer wrote:
    Hi,
    I don't know if this is even possible but here's what I'd like to do:
    I've started to share an internet connection with a cousin of mine that lives in my apartment building. The connection is in her apartment and as far as I can tell the wireless signal is coming from the modem she has, there is no stand alone router/ base station.
    She has an "integrated" modem/router/access point.
    So far I've just been connecting using my iBook with the aiport card in it. No problems. I just had to get the ip number and password from her and I was hooked right up.
    Here's my real question:
    I also have a G4 Mini with no wireless card in it at all and an Airport Extreme base station from before we started sharing a connection. In the time that we've been sharing I haven't connected to the internet at all using the Mini. Now I'm wondering if there is a way I can hook the Airport Extreme to the Mini and somehow use it as a replacement for a wireless card in the Mini. Thus using the Mini connected to the Airport to connect just the Mini to the internet.
    I'm not worried about the iBook and do not wish to reconfigure the way I'm using/ connecting with it. Everything is peachy with that.
    If this is possible, how can I do it?
    Set up the AEBSn as a "bridge" and connect the G4 Mini to one of the "wired" internet connections.

  • Wireless connection to internet with mac pro tower and airport extreme base station?

    Hi, I have an airport extreme base station and a mac pro tower without a airport card. My internet wireless router is a great distance from my computer so I can't connect the base station directly to the router. I've attached the airport extreme base station to the tower via an ethernet cable, the base station seems to be wirelessly connected to the home network but the browser is showing "not connected".
    Please help.
    Thanks

    Shouldn't the Airport base station be able to connect to it wirelessly?
    It might be possible, but the Ethernet ports on the AirPort Extreme would not be enabled, even if it did connect to the Thompson' WiFi signal.
    As Tesserax notes, among the Apple routers, only the 802.11n versions of the AirPort Express have the capability to "join" a wireless network with the Ethernet port being enabled.

  • Setting up airport extreme card and airport extreme base station

    I have an ibook G4 about 3 years old with osx10.4.10 recently installed. I have recently bought an airport extreme card and have also bought an airport extreme base station.
    There seems to be a problem with the set up of the card. It does not seem to find any wireless networks at all, including the base station. The base station seems to be working as I went through setting this up with Apple phone support and we managed to do it by connecting the laptop to the base station with an ethernet cable.
    I think the problem is with the card. I think I need to reinstall and set up the card again from scratch, but can't figure out how to do this -aiport utility and airport setup assistant don't seem to help here as they take you straight to the stage of setting up a base station. I seem to remember when I originally installed the card for the very first time (before attempting to set up the base station) that it did find other wireless networks, so I don't think there is a physical problem with the card.
    Any suggestions on getting the card working appreciated.
    Many thanks

    Hello bblairlondon. Welcome to the Apple Discussions!
    First, verify if OS X "recognizes" the card, by using the System Profiler utility. Select the AirPort Card option under Network in the column on the left. The "Wireless Card Type" should be "AirPort Extreme (nxnnnn, nxnnnn)."
    If no card appears, I suggest that you double-check your AirPort Extreme Card installation by using the following Apple Tech article: iBook G4: CIP Instructions
    If the card does appear, then try the following ...
    Reset the PRAM
    o Shut down the computer.
    o Turn on the computer.
    o Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    o Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    o Release the keys.
    (ref: Resetting your Mac's PRAM and NVRAM)

  • How do I find a hard drive connected to Airport Extreme Base Station?

    *Apple Says:* "If your base station supports it, you can connect a USB hard disk to the USB port on your base station and computers on your network (both wired and wireless) can connect to it to access, share, and store files and data."
    Cool. So I followed the instructions. The drive is recognized by the base station and listed in the Airport Utility. It looks like it's ready to go...
    So... How do I access the drive? I don't see it on my desktop, it's not under network. I've tried "Connect to server..." and browsing, I can't see the drive, anywhere. Yeah, I've searched the crap out of this issue on google and this message board as well as apple support knowledge base. I'm sure this is a simple issue and I'm just missing the obvious. Help me out.

    Hello Timothy Uhl. Welcome to the Apple Discussions!
    Try the following to mount the disk...
    o Click on the Desktop to enter Finder
    o Go > Connect to Server...
    o Enter 10.0.1.1 for the server
    o Enter Disk Password
    o Connect
    If this still doesn't solve the problem, let's double-check your disk sharing settings...
    AirPort Extreme Base Station (AEBSn) - File Sharing Setup
    Either connect to the AEBSn's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Mode, check these settings:
    Disks - File Sharing
    o Secure Shared Disks: <With disk password | With base station password | With accounts >
    (Note: Choose "With a disk password," or "With base station password" if you want to secure the shared disk with a password, or choose "With accounts" if you want to secure the disk using accounts.
    If you choose to use accounts, click Configure Accounts, click the Add "+" button, and then enter a name and password for each user that will access the disk.)
    o Guest Access: <Not allowed | Read only | Read and write>
    o Share disks over Ethernet WAN port: (unchecked)
    (Note: Select the "Share disks over Ethernet WAN port" checkbox if you want to provide remote access to the disk over the WAN port.)
    o Advertise disks globally using Bonjour: (unchecked)
    o Workgroup: <Windows workgroup name>
    o WINS server: <WINS server IP address>

Maybe you are looking for