OSX 10.9 not showing all network drive contents
Hi,
I one of the users in our department has updated to osx 10.9
when the user connects to the network drive it connects but when the user navigates to the folder they need it appears to be empty.
We have tested on or Macs and the contents show up fine.
Any help would be greatly appreciated.
I have tried both smb:// and cifs:// but to no avail.
Thanks
Hi,
There are few hiccups after 10.9 release. Have you checked and installed the following pathch ?
http://support.apple.com/kb/DL907?viewlocale=en_US&locale=en_US
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Similar Messages
-
Could not reconnect all network drives
I have several drives mapped on different Windows 7 boxes in my office. Just about every time I boot up one of these systems I receive the message "Could not reconnect all network drives" in the system tray.
I should note that merely clicking the drive inside Windows Explorer will restore the connection. I store the server logon credentials in Control Panel / Credential Manager then just map the network paths to drive letters. I'm pretty sure the
problem doesn't stem from any credentials type of problem though, because I have the exact same situation when connecting to only open shares. I have noticed that a couple applications will restore the connection themselves when trying to access information
on a share. Most applications however will give an error and time out trying to access the shares unless I go and manually click each drive letter in Explorer. For instance if I place Firefox bookmarks on a share and open Firefox, Firefox will
display no bookmarks until I click the drive in Explorer and reopen Firefox.
One thing I can do to fix the problem is hard code my IP address. I never receive the message if a computer has fixed IP address. My router hands out IPs on the LAN dynamically, so I switch it to another router and tried a using a Linux based dhcp-server
as well. Neither fixed the problem.
I'm a long time user of batch files and realize I could place use one as a band aid for this issue, but I don't want to go that route.Hello marstech,
According to the research, the mapped drive lost issue may be caused by the several possible reasons:
Possible reason1. The problematic client doesn't reconnect to the target share at logon.
Please follow the steps to re-configure the mapped driver on the client and then check if the issue will re-occur.
Steps:
a. Open "My Computer"
b. Click on "Tools" and then select "Map Network Driver"
c. input the \\ipaddressofserver\sharename to give the path of the share
d. Check "Reconnect at logon"
e. Drive gets mapped
f. Double click on the drive to check.
Possible Reason 2. Antivirus software or Windows Firewall may block the SMB protocol on clients.
Please check if there is any Antivirus software and the Windows Firewall is enabled on the problematic client. If so, please disable them to check if the issue can be resolved.
Possible Reason3. Fast Logon Optimization is enabled on the clients.
The fast logon feature may affect the display and drive letter assignment of a mapped network drive. As a result, the drive may have been mapped; however, the user on client cannot see it in Windows Explorer. He may recognize it as a failed network drive mapping.
This is the reason why we usually suggest you to disable fast logon on the clients via a GPO, and please check if the mapped network drive will be occur under this circumstance.
Please also configure the following group policy setting to disable Fast Logon Optimization to see if the issue still exists on the problematic clients.
Computer Configuration\Administrative Templates\System\Logon\Always wait for the network at computer startup and logon
When this policy is enabled, a Windows XP client behaves in the same manner as a Windows 2000 client at both system startup and at user logon.
Please note: As this is a computer configuration, please run "Gpupdate /force" and then reboot the problematic clients to make it take into effect.
For more information about Fast Logon Optimization feature, please check the following KB article.
305293 Description of the Windows XP Professional Fast Logon Optimization feature
http://support.microsoft.com/?id=305293
831998 Mapped network drive shows no drive letter or will not allow you to create new long-named files or folders
http://support.microsoft.com/kb/831998
297684 Mapped Drive Connection to Network Share May Be Lost
http://support.microsoft.com/kb/297684
If the issue still exists on the problematic clients, please also try adding the following registry subkey on the problematic client to check it works.
Steps:
a. Click Start, click Run, type REGEDIT, and then click OK.
b. Locate and click the following registry subkey:
HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\NetCache
c. Click Edit, point to New, and then click DWORD Value.
d. Type SilentForcedAutoReconnect , and then press ENTER to name the value.
e. Double-click SilentForcedAutoReconnect .
f. In the Value data box, type 1, and then click OK.
Please feel free to let me know if you have any concen.
Hope the information can be helpful for you.
Thanks and Regards
Scorpio_Milo
MCTS: Windows Vista | Exchange Server 2007
MCITP: Enterprise Support Technician
MCITP: Server & Enterprise Administrator
Microsoft Infrastructure Consultant
Enterprise Service: Solution Architect
Microsoft Storage Team - File Cabinet Blog
My Blog -
Photoshop CS6 is not showing any network drives within windows 8.1.
Photoshop CS6 is not showing any network drives within windows 8.1, I can only browse the local disk for files. Please advise?
And when i try opening a file directly from the network, photoshop starts but does not open the selected file?The dialog you show there looks like it may be a CS6 open dialog running on windows 8.1 that is showing what is local. Network is not highlighted selected.
Here is a CC Open one windows 7 pro showing areas of what is accessible. -
Media Go not showing all phone's content
Why does Media Go not show all my music and photos?
http://talk.sonymobile.com/t5/Xperia-S-SL-acro-S/Google-Play-Services-cannot-be-found/m-p/1009358/highlight/false#M40125 based on your last post, it seems that you have rooted your phone, have you done anything else other than rooted the phone?
-
Finder not showing connected network drives in Devices section
I have a number of network drives on my LAN, some NAS drives, some other Macs and of course a Time Machine. Prior to updating to OSX 10.9.5 when I used finder to connect to one of these shares the name of the connected share used to appear in the Finder Sidebar - under the devices section. Now when I do this nothing appears, although I do get an icon on the desktop and I can still access the remote files.
I have set/reset all the finder view settings from the Preferences panel and also tried deleting the finder and sidebar preferences files without improvement. I do have "Path Finder" installed as well and this still works as normal.
I contacted Apple support and after a hour or so they promised to get an engineer to get back to me sometime this week.
Has anyone else seen this behaviour ?
If Apple don't come up with any ideas I will have to experiment with uninstalling other apps which might indirectly case it, like Path Finder and even Paragon NTFS drivers.
It's not a show stopper, but a rather annoying inconvenience.
Thanks in advance for any replies
DaveHello birdy.....,
Sorry to take so long responding. Major disaster! My whole wall bookcase just tumbled, and I'm still working at excavating the family (of Macs).
Your card should work. I've used the Acard cards by the dozens without problem, though I've never used that particular 6860 card or set up a RAID ARRAY. Just checked, using a 6880 (RAID) though as a controller card and not as a RAID ARRAY, and found that my 2002 QS Mac would not see a standard hard drive(#2) running OSX (10.2) that had been formatted by the OSX install disk using the stock bus on the motherboard. It would, however, see a hard drive(#3) that had been formatted while connected to an ACARD controller card (6280). I'm guessing that an OSX installer disk is prepared to see and to deal with a SCSI drive, and that Disk Utility is not.
Check that.
Just removed the controller card formatted drive(#3) and re-installed the OSX(10.2) drive(#2); this time my 2002 QS saw it right away, both on the desktop and in disk utility. I guess it needed personal messenger service.
As I recall, I've seen that happen before using controller cards; as a result, I've always taken care to format a new hard drive by connecting it to a controller card if that is the way I intend to use it. Hard drives can be capricious, sometimes. At any rate, try formatting your hard drive(s) with an OSX installer disk (hoping you have one) while connected to the ACARD controller card - just click on erase (twice) and the drive formats automatically.
I'm a little mystified by reference to drivers; never installed any drivers, and always assumed none were needed.
Hope that helps. Check back and let me know.
Jon -
My iphone4 and my ipad mini were synced to my computer, but now I don't seem to be able to see all of my content nor my photo stream. I did see everything there several weeks ago, so I know it worked. How do I access those from my computer. I can't find how to sign on.
I signed on to iCloud, but it only shows the icons for Mail, Contacts, Calendar, Notes, Reminders, Find Phone, Numbers, Pages and Keynotes. Where's everything else ?
I want to delete photos that are on my iphone, by doing so from the computer, not my phone.deltajane wrote:
My iphone4 and my ipad mini were synced to my computer, but now I don't seem to be able to see all of my content nor my photo stream. I did see everything there several weeks ago, so I know it worked. How do I access those from my computer. I can't find how to sign on.
This is the article that will assist with this part of your post:
http://support.apple.com/kb/ht4486
deltajane wrote:
I signed on to iCloud, but it only shows the icons for Mail, Contacts, Calendar, Notes, Reminders, Find Phone, Numbers, Pages and Keynotes. Where's everything else ?
What you've outlined in this part of the post is all that icloud stores for you outside of the backup. If you want to restore from the icloud backup you will then have for all practical purposes a carbon restoration back to your device if you restore from the icloud backup.
deltajane wrote:
I want to delete photos that are on my iphone, by doing so from the computer, not my phone.
Syncing your device with itunes will then enable you to remove whatever photos you wish to remove from your device deleting them with the computer and not the iphone. -
Impossible to reconnect all network drives
H there,
On my Windows 8, I have defined 3 network drive (from my NAS), and although I am checking the box to save the credentials (which are different on the NAS and on Windows), at each reboot of the laptop it tells me it can not reconnect all network drives, and
I see a red cross on the map.
How can I solve this, As I am SURE the remote drivs are available ( and when I click the "disconnected drive", it ask for th elogin and PW, I enter it and it works ... but I need to do that manually all the time)
Thanks !Hi,
Regarding you issue, remapping drivers in logon script is a better way.
To map network driver, you can refer to this article below:
http://www.itninja.com/blog/view/mapping-drives-in-logon-scripts-is-there-a-better-way
Note Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Thanks!
Andy Altmann
TechNet Community Support -
Ical not showing all day events in lion osx
ical does not show all day events
Hi,
I noticed that the issue only happens to specific user with specific computer. Please do the following checking to narrow down the issue:
1. please update the Outlook client with the latest patches and service packs.
2. disable using Exchange cached mode and check whether the issue happens in Online mode in this computer.
3. Start
Outlook in safe mode to have a try.
4. Perform a clean boot
in your Windows for the new machine.
Regards,
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Winnie Liang
TechNet Community Support -
SMB share not showing all available files
Hi,
At work I have to connect to several SMB shares. Most are fine, however 1 of them does not show all the files that are on that share. I know I'm using the right domain, username and password. I've checked the console and can see this message repeated when I connect.
mbgetmem(449): incomplete copy
mbgetmem(449): incomplete copy
mbgetmem(449): incomplete copy
mbgetmem(449): incomplete copy
I'm using OS X 10.4.8 and have no idea of how to proceed. My IT department do not support our Mac's so any help would be greatly appreciated.
Many Thanks
Kieranexcellent reply. Thanks for the details.
Oh, one more thing-
this 30-item limit is just in this same troublesome share.
Before the day gets away from you, ask the network admin to check permissions on this share. Perhaps the 30 files you see are the only ones that you have explicit rights to view.
they may need to ease up on restrictive permissions on this folder/drive.
(Images over a network can be funky, since Mac wants to display a little thumbnail of all those picture files...if you're viewing 'as icons', what happens if you change to 'by list'?...thinking out loud there.)
(not sure if I posted this...lost an open window for a few minutes :o -
I can not map a network drive in window 8.1 via VPN
Dear sir / madam,
I face a big problem. My company use VPN Connection. After my company upgrade the window from Window 7 to Window8.1 , we find that we can not reconnect the network drive. please find the details below:
1. I success to map drive and then logout / switch user.
2. wait two /three hours
3. i find the drive is disconnected.
4. when I try to reconnect, window can not find again. then I try to use netstat
C:\Windows\system32>netstat
TCP 172.28.97.31:58206 test-server:http TIME_WAIT
Then, i try to use cmd
5 it show reconnect successful by net use command. However , I need waste many time and I can not find the drive in window.
if I restart window, i can reconnect it quickly and find the drive in window.
the server is window server 2008 r2 and located at difference site.
if the server and PC located at same site, it is no problem.
both the server and PC are joined in same domain.
it is dell server and Lenovo M82 PC
please help me to solve the problem
(window 7 also have this problem. However, i can click the drive and it can reconnect quictly.i cannot do this in window 8.1.......it loop again)
thanksHi,
Is there any error message throwed when you reconnect the mapped drive? Can you directly access the UNC path of the mapped drive? What VPN programs do you use? Please check if the VPN client connect correctly.
You could refer to the thread below to check if the AD account is restricted by VPN.
Can't access mapped drives through VPN when away from office
http://social.technet.microsoft.com/Forums/windows/en-US/a0ca41aa-08b8-4e46-a314-ffb7e401bd7a/cant-access-mapped-drives-through-vpn-when-away-from-office?forum=w7itpronetworking
Best Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
I can not map a network drive in window 8.1 under VPN
Dear sir / madam,
I face a big problem. My company use VPN Connection. After my company upgrade the window from Window 7 to Window8.1 , we find that we can not reconnect the network drive. please find the details below:
1. I success to map drive and then logout / switch user.
2. wait two /three hours
3. i find the drive is disconnected.
4. when I try to reconnect, window can not find again. then I try to use netstat
C:\Windows\system32>netstat
TCP 172.28.97.31:58206 test-server:http TIME_WAIT
Then, i try to use cmd , net use /delete and then try to reconnect test-server
5 it show reconnect successful by net use command. However , I need waste many time and I can not find the drive in window.
if I restart window, i can reconnect it quickly and find the drive in window.
the server are window server 2008 r2 and server 2012, they located at difference site.
if the server and PC located at same site, it is no problem.
both the server and PC are joined in same domain.
it is dell server and Lenovo M82 PC( Intel Lan 82579LM/V Driver)
please help me to solve the problem
(window 7 also have this problem. However, i can click the drive and it can reconnect quictly.i cannot do this in window 8.1.......it loop again)
thanksHi,
How did you map the network drive? Manually via GUI? Command? GPP? If you're using one of the above solutions, then try other solutions as a alternative way to check the result.
According to your description, If Windows remains unable to reconnect mapped Network Drive at login, then I would suggest you created a batch file with net use command, use it as an logon script, this provides an alternate way to reconnect drives on
a re-logon.
example
@echo off
net use * /delete /yes
net use x: \\server_name\shared_directory_name
You can find detailed information in the following link
https://helpdesk.egnyte.com/hc/en-us/articles/201638304-Mapping-a-drive-using-a-net-use-command-and-logon-scripts-for-domain-users
http://technet.microsoft.com/en-us/library/bb490717.aspx
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Yolanda Zhu
TechNet Community Support -
My Adobe Photoshop Cs4 Is Not Showing all Formats/Extensions.
when i edit a picture and wants to save in .png or .bmp or in any other format ...
there is no .png In the Save As List, There are only Some Extenstions in that list like Jpeg-Psd-Tif etc...
I Made The Picture in RGB mode..
And I have Png.8bi Present In my AdobePhotoshop/Plugins/File Formats
But It Is Still Not Showing Can you guys helpThanks For The Reply ... Let Me Answer your questions
Os = Windows ( windows xp )
Bits = 8 bits / Channel
I didn't Understand your this question
=> If On Windows is it the same in both the 32 and 64 bit versions of Photoshop cs4?
System Info :-
Adobe Photoshop Version: 11.0 (11.0x20080919 [20080919.r.488 2008/09/19:02:00:00 cutoff; r branch])
Operating System: Windows XP 32-bit
Version: 5.1 Service Pack 3
System architecture: Intel CPU Family:15, Model:2, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2
Physical processor count: 1
Processor speed: 1394 MHz
Video Card: Intel(R) 82845G Graphics Controller
Video Mode: 1152 x 864 x 4294967296 colors
Video Card Driver: ialmrnt5.dll
Driver Version: 6.13.01.3264
Built-in memory: 2046 MB
Free memory: 1497 MB
Memory available to Photoshop: 1586 MB
Memory used by Photoshop: 70 %
Image cache levels: 4
Serial number: 92628791954238016438
Application folder: D:\CS4\Photoshop CS4\
Temporary file path: C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\
Photoshop scratch has async I/O enabled
Scratch volume(s):
Startup, 39.1G, 32.0G free
Primary Plug-ins folder: D:\CS4\Photoshop CS4\Plug-ins\
Additional Plug-ins folder: not set
Installed components:
ACE.dll ACE 2008/08/27-18:10:41 53.355610 53.355610
AdobeLinguistic.dll Adobe Linguisitc Library 4.0.0
AdobeLM.dll AdobeLM 3.0.11.10077 (BuildVersion: 53.352460; BuildDate: Tue Jul 29 2008 16:47:08) 53.352460
AdobeLM_libFNP.dll FLEXnet Publisher (32 bit) 11.5.0.1 build 57427
AdobeOwl.dll Adobe Owl 2008/08/14-18:38:42 2.0.70 53.354161
AdobeOwlCanvas.dll Adobe Owl Canvas 2.0.70 53.354161
AdobePDFL.dll PDFL 2008/08/20-20:15:08 53.204060 53.204060
AdobeUpdater.dll Adobe Updater Library 6.0.0.1452 (BuildVersion: 52.338651; BuildDate: Wed Apr 16 2008 19:28:20) 52.338651
AdobeXMP.dll Adobe XMP Core 4.2.2 53.352624
AdobeXMPFiles.dll Adobe XMP Files 4.2.2 53.352624
AdobeXMPScript.dll Adobe XMP Script 4.2.2 53.352624
adobe_caps.dll Adobe CAPS 2,0,99,0 2.135373
AFlamingo.dll AFlamingo 2008/07/09-11:28:44 53.350580 53.350580
AGM.dll AGM 2008/08/27-18:10:41 53.355610 53.355610
ahclient.dll AdobeHelp Dynamic Link Library 1, 3, 12, 0
aif_core.dll AIF 1.0 53.352475
aif_ogl.dll AIF 1.0 53.352475
amtlib.dll AMTLib 2.0.1.10077 (BuildVersion: 53.352460; BuildDate: Tue Jul 29 2008 16:47:08) 53.352460
amtservices.dll AMTServices 2.0.1.10077 (BuildVersion: 53.352460; BuildDate: Tue Jul 29 2008 16:47:08) 53.352460
ARE.dll ARE 2008/08/27-18:10:41 53.355610 53.355610
asneu.dll AsnEndUser Dynamic Link Library 1, 6, 0, 8
ATL80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
authplay.dll
AXE8SharedExpat.dll AXE8SharedExpat 2008/06/11-20:19:53 NFR 53.348206 53.348206
AXEDOMCore.dll AXEDOMCore 2008/06/11-20:19:53 53.348206 53.348206
Bib.dll BIB 2008/08/27-18:10:41 53.355610 53.355610
BIBUtils.dll BIBUtils 2008/08/27-18:10:41 53.355610 53.355610
cg.dll NVIDIA Cg Runtime 2.0.0015
cgGL.dll NVIDIA Cg Runtime 2.0.0015
CoolType.dll CoolType 2008/08/27-18:10:41 53.355610 53.355610
data_flow.dll AIF 1.0 53.352475
ExtendScript.dll ExtendScript 2008/07/17-13:28:24 53.351316 53.351316
FileInfo.dll Adobe XMP FileInfo 4.2.2 53.352624
FNP_Act_Installer.dll FLEXnet Publisher (32 bit) 11.6.0.1 build 60959
icucnv36.dll International Components for Unicode 2008/03/20-16:33:10 Build gtlib_1.1 CL#7223
icudt36.dll International Components for Unicode 2008/03/20-16:33:10 Build gtlib_1.1 CL#7223
image_flow.dll AIF 1.0 53.352475
image_runtime.dll AIF 1.0 53.352475
JP2KLib.dll JP2KLib 2008/06/11-20:19:53 53.100857 53.100857
libifcoremd.dll Intel(r) Visual Fortran Compiler 10.0 (Update A)
libmmd.dll Intel(r) C Compiler, Intel(r) C++ Compiler, Intel(r) Fortran Compiler 10.0
mfc80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80CHS.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80CHT.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80DEU.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80ENU.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80ESP.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80FRA.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80ITA.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80JPN.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80KOR.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfc80u.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfcm80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
mfcm80u.dll Microsoft® Visual Studio® 2005 8.00.50727.762
MPS.dll MPS 2008/07/07-10:33:04 53.350311 53.350311
msvcm80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
msvcp71.dll Microsoft® Visual Studio .NET 7.10.3077.0
msvcp80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
msvcr71.dll Microsoft® Visual Studio .NET 7.10.3052.4
msvcr80.dll Microsoft® Visual Studio® 2005 8.00.50727.762
pdfsettings.dll Adobe PDFSettings 1.04
Photoshop.dll Adobe Photoshop CS4 CS4
Plugin.dll Adobe Photoshop CS4 CS4
PlugPlug.dll Adobe(R) CSXS PlugPlug Standard Dll (32 bit) 1.0.0.73
PSArt.dll Adobe Photoshop CS4 CS4
PSViews.dll Adobe Photoshop CS4 CS4
registration.dll Registration 2.0.1.10077 (BuildVersion: 53.352460; BuildDate: Tue Jul 29 2008 16:47:08) 53.352460
SCCore.dll ScCore 2008/07/17-13:28:24 53.351316 53.351316
shfolder.dll Microsoft(R) Windows (R) 2000 Operating System 5.50.4027.300
VersionCue.dll Adobe VersionCue 4.0.0.0client1
WRServices.dll WRServices Friday May 30 2008 7:18:42 Build 0.7713 0.7713
Installed plug-ins:
ADM 3.11x01
Accented Edges 11.0
Angled Strokes 11.0
Bas Relief 11.0
Chalk & Charcoal 11.0
Charcoal 11.0
Chrome 11.0
Colored Pencil 11.0
Conté Crayon 11.0
Craquelure 11.0
Crosshatch 11.0
Cutout 11.0
Dark Strokes 11.0
Diffuse Glow 11.0
Dry Brush 11.0
Embed Watermark 3.0
Film Grain 11.0
Filter Gallery 11.0
Fresco 11.0
Glass 11.0
Glowing Edges 11.0
Grain 11.0
Graphic Pen 11.0
HDRMergeUI 11.0
Halftone Pattern 11.0
Ink Outlines 11.0
Lens Blur 11.0
Lens Correction 11.0
Liquify 11.0
Mosaic Tiles 11.0
Neon Glow 11.0
Note Paper 11.0
Ocean Ripple 11.0
Paint Daubs 11.0
Palette Knife 11.0
Patchwork 11.0
Photocopy 11.0
Plaster 11.0
Plastic Wrap 11.0
Poster Edges 11.0
Read Watermark 3.0
Reticulation 11.0
Rough Pastels 11.0
Save for Web & Devices 11.0
ScriptingSupport 11.0
Smudge Stick 11.0
Spatter 11.0
Sponge 11.0
Sprayed Strokes 11.0
Stained Glass 11.0
Stamp 11.0
Sumi-e 11.0
SuperPNG 2.0
Texturizer 11.0
Torn Edges 11.0
Underpainting 11.0
Vanishing Point 11.0
Variations 11.0 (11.0x001)
Water Paper 11.0
Watercolor 11.0
Plug-ins that failed to load: NONE
Flash: 0
Installed TWAIN devices: NONE -
Workstation not mapping any network drives
Im having an issue with different workstation not mapping any network drives. The issue to would seem totally random. Each time is over a wired connection. I havent been able to find a TID about this. The issue also just seems to have started, however no changes have been made to any of the workstations Ive seen this on. The errors I get in the login script are below. The servers are all NetWare 6.5SP7. Suggestions?
LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 15 (8819).
LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 13 (8819).
LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 9 (8819).
LOGIN-LGNWNT32.DLL-918: This utility was unable to get connection information. Error code: 8801Hi,
technomoney wrote:
>
> Im having an issue with different workstation not mapping any network
> drives. The issue to would seem totally random. Each time is over a
> wired connection. I havent been able to find a TID about this. The
> issue also just seems to have started, however no changes have been made
> to any of the workstations Ive seen this on. The errors I get in the
> login script are below. The servers are all NetWare 6.5SP7.
> Suggestions?
>
> > LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 15 (8819).
> > LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 13 (8819).
> > LOGIN-LGNWNT32.DLL-923: An unexpected error has occurred: 9 (8819).
> > LOGIN-LGNWNT32.DLL-918: This utility was unable to get connection
> > information. Error code: 8801
Basic network connectivity issue. One known common culprit for this
error is a workstation firewall, but the raw symptom just means that
unexpected network connectivity problems occured.
CU,
Massimo Rosen
Novell Product Support Forum Sysop
No emails please!
http://www.cfc-it.de -
ITunes suddenly not showing all my content, even though the folder does
All of the sudden, iTunes stopped showing all of my content. I have over a hundred movies and several TV shows and all of the sudden, some of the newer stuff that I recently ripped or bought from the iTunes store is no longer showing up in iTunes.
It is still in my iTunes folder however and open and accessible if I click it in Finder. This however is not a good solution as I don't know what is missing from the list and how this ridiculous issue happened.
I am furious. I spend a lot of time adding to my iTunes library for my Apple TV and suddenly, and for no reason that I can discern, content is not showing up, no matter what I do.
I recently moved my iTunes library to a 2 TB Time Capsule and took it off my internal drive, but this worked fine. For a while iTunes kept losing the library, but it no longer asks for it. It points to the right place, plays the content it chooses to see from the right place, and ignore others even though it showed them before and still has them in the library.
I am beyond confused. Can anyone help?Check on the Summary tab of your iTunes sync settings that you checked "Sync only checked songs and videos" and that you checked "Sync Music" on the Music tab. Also confirm that your computer authorized for the Apple ID used to purchase this music (in Store>Authorize this computer).
-
Lightroom not showing all photos avail for import
About a week ago, I tried to import some new photos into LR 3 (3.4.1 to be exact), and the import dialogue does not show all the photos that should be available for import.
The files are on my hard drive and there are approximately 200 photos in the file folder. When I open LR's import dialogue to import the photos (after navigating to the proper location to import from of course), it shows me 17 of the photos in the file folder! I selected "all" instead of "new" to see if that would make a difference and it did not. I made sure I did not have "do not import suspected duplicates" checked, even closed LR and rebooted my computer.... that didn't work.
I tried creating a new catalog to see if that would fix the issue, and it did not.
I'm not sure what else to try, or if there is a known fix out there (having a heck of a time finding one in my internet search!)
Any ideas/suggestions?
Thanks!
-KBPOkay, so for giggles I tried checking in the Bridge to see if that changed anything... and it only showed the few files too. So I decided to "select all" and noticed at the bottom left that it listed the balance of my photos as "hidden." I have no idea how my files got hidden, or why it was only some and not others... but at least it's all fixed now and I can get back to what I need to do in LR!
Maybe you are looking for
-
Multiple simutaneously logged in users accessing AFP home directories?
Hi, Many of our problems are described in this guy's blog: http://alblue.blogspot.com/2006/08/rantmac-migrating-from-afp-to-nfs.html The basic capability we want is to have multiple simultaneously logged in users to have access to their AFP mounted h
-
Powermac G5 with HD TV and DVI formac monitor
Hello I recently bought a hd tv which I would like to run together with my DVI monitor. I was looking at getting an adc to dvi adaptor but thought it may slow down performance. Then I thought about having two graphics cards. would this be possible? I
-
How to upload a file to different location using CS Template
Hi,I have a Data Entry Template with a "File" field and when I upload a document it uploads in the same directory where the Content Item is created. Is there any way to upload the document to some other directory in the Content Server. Say I have a H
-
.class Files with "$X" extensions
Hi everybody, when I deploy my App, some confusing .class files are generated by my JDev (10.1.3.3) ... In my Project I declare a Class named - JClientDesktopManager.java This is compiled to two .class files: - JClientDesktopManager.class - JCli
-
Best workflow for exporting clips
Hello. I have an hour long video that needs to be cut and exported as 40 individual QT movies. What is the best way to do this? I have set markers at all the points that need to be cut. How can I highlight between markers and then export that area as