Other PC can access internet via cable but not via wireless.

Hi, I am new here. But I have a question hopefully someone can help to answer. I juts got myself signed up for one of those portable USB modem that you can use anywhere and you use a phone sim card to access the internet. I connect the usb device to my desktop computer and use a linksys wireless router to connect to other pc in the house. My problem is that the internet can be access by other pc's if I connect the other pc's via a network cable but no internet all if I connect via wireless. Any reason why it work via cable and not via WIFI? Is it the setting inside the router that is not set correctly. I pretty much left the setting on factory default except for the wireless network name. Any help to explain why this is happening is much appreciated. Thanks. Alex

Follow these steps to upgrade the firmware on the device: - Open
an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin
Click on the 'Administration' tab- Then click on
the 'Firmware Upgrade' sub tab- Here click on 'Browse' to select the
extracted/uncompressed .img or .bin file and click on "Upgrade"-Wait for few seconds ....
It shows that "Upgrade successful"  After
the firmware upgrade, click on "Reboot" and you will be returned back
to the same page OR it will say "Page cannot be displayed".
Reset the router for few seconds ....
Reconfigure it ....

Similar Messages

  • I can access my music library, but not the Itunes store. Just getting a white screen. It starts to connect but just stops. Any suggestions?

    I can access my music library, but Itunes Store is not opening. I am just getting a white screen. Any suggestions?

    Reset the device:
    Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
    If that doesn't help, tap Settings > General > Reset > Reset All Settings
    If that didn't help, tap Settings > General > Reset > Reset Network Settings
    You will have to re enter the Wi-Fi password.
    If that doesn't help, try here >  iOS: Troubleshooting Wi-Fi networks and connections
    No data is lost due to a reset.

  • I can't access shared Photo Streams from my Mac but can from iPhone/iPad. I can access my Photo Stream but not the shared ones.

    I can't access shared Photo Streams from my Macbook but can from iPhone/Ipad. I can access my Photo Stream but I can't figure out how to share.

    I can't access shared Photo Streams from my Macbook but can from iPhone/Ipad. I can access my Photo Stream but I can't figure out how to share.

  • HT1694 I have recently updated my iPad and cannot access my mail account (I can access it through Microsoft) but not the mail app that's on iPad.. It continually keeps saying cannot verify account or password.

    I have updated my pad and now cannot access my Email through mail on the ipad (I can access it on the internet via Microsoft ) I have tried changingassword and server to pop3... But nothing working that if read from ppl. Please help.. As I love using mail on the pad making it much faster and easier to view my mail. I don't wanna go back to logging in over the web....   Please help :)

    When resetting your password, did you turn on two-step authentication? If you did, the Mail App isn't compatible with it - either, you need to create an application password and use that to log in using the iPhone Mail App, (instead of your Microsoft Account password) or disable two-step authentication to make it work.
    There's more here:
    http://windows.microsoft.com/en-GB/windows/two-step-verification-faq

  • Can access share by alias1, but not by alias2 (from xp client)

    Hello,
    I have fileserver.domain.com
    and clientXP.
    I have two aliases for fileserver.domain.com which I added via netdom command:
    alias1.domain.com and alias2.domain.com
    From clientXP I can access both \\fileserver and
    \\alias1 fine, however when trying to access
    \\alias2 I get the error:
    "you were not connected because a duplicate name exists on the network. Go to system in control panel to change the computer name and try again."
    "alias2" name is not used anywhere else in our network.
    Nslookup seems to resolve "alias2" correctly from clientXP.
    alias1 was added few months ago, so I can't exactly remember if there were any additional steps taken to make it work.
    I have tried setting disable strict name checking dword to 1, which seems to have no effect in my situation.

    OK it seems all I had to do is to restart fileserver, after that I could normally access file shares on it from clientXP by the name of alias2.

  • Can access server by IP but not by name

    I am having a problem similar to the one here:http://community.spiceworks.com/topic/244382-cannot-access-file-server-by-name-but-can-by-ip?page=1When accessing a server by name, I receive"\\servername is not accessible. You may not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The target account name is incorrect"The thread I linked to above isold and I didn't want to try to tag onto the end of it.I have a group of servers all on a local subnet. There are two DCs and 12 member servers. The main data server is one of the DCs. After some reboots, over half of the servers can no longer access the data server by name \\SHSMASTER, but can access it fine by IP. Ping resolves the name properly.I've ruled out anything that's specific to one station, like DNS...
    This topic first appeared in the Spiceworks Community

    I have been involved in the hiring process for our Security Operations Center (SOC) for about a year and a half. Throughout this time, I have reviewed resumes, conducted phone screens, and participated in the technical interviewing process. I have been both dumfounded by the audacity of some individuals and amazed by the sheer awesomeness […]…Read MoreThe post Landing a Hands-On Security Gig – Part 1 appeared first on The State of Security.
    Read More

  • I can access internet via boot camp with windows 7, but not when I use the Mac w/Mt Lion side. Thanks for any tips!

    I'm using a 2012 Intel-based iMac with Mt. Lion and Windows 7 with Boot Camp. I used to be able to access the internet on both sides. Now, my only internet access is through Boot Camp. At one point, access was unable on both sides but IE in Windows 7 automatically diagnosed the problem, changed some settings (which I don't know) and I could access the internet on both sides . . . for a while. Now, I can only get online in Boot Camp. Since IE detects no problems it doesn't apply the fix as it did before. Does anybody know what's going on?
    I should mention that I installed Boot Camp because there is no Mac version of the software (VantagePoint)  I need to use (duh).  I wanted to be able to use the software w/o rebooting all the time so I installed Fusion. Of course, I didn't ask the VantagePoint techs if this would solve my issue. It didn't - VantagePoint won't work with Fusion, but it will with Parallels. So I installed Parallels and imported Boot Camp. Apparantly, it was not set up properly, I'm getting all kinds of errors reported in Console (e.g. "Found cross-bounds GPT partition. GPT disk detected," mdworker cannot talk to sandbox, etc.).  The VantagePoint techs say the first step in a VM retry is to regain internet access to the Mac.
    Anybody who can help will become my new best friend. Thanking you.
    Message was edited by: Marmadukemark
    Windows IP Configuration
       Host Name . . . . . . . . . . . . : Mark-PC
       Primary Dns Suffix  . . . . . . . :
       Node Type . . . . . . . . . . . . : Hybrid
       IP Routing Enabled. . . . . . . . : No
       WINS Proxy Enabled. . . . . . . . : No
    Ethernet adapter Bluetooth Network Connection 2:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Bluetooth Device (Personal Area Network) #2
       Physical Address. . . . . . . . . : 44-2A-60-CF-D0-93
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
    Wireless LAN adapter Wireless Network Connection 2:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
       Physical Address. . . . . . . . . : 32-9A-DD-9F-1D-FF
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
    Ethernet adapter Local Area Connection:
    I neglected to add that I'm using using ethernet with a cable modem. I'm the only user, so it's not networked for others. Below is the report that was generated with respect to the connection problem - when Boot Camp could not access the internet.
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
       Physical Address. . . . . . . . . : C8-2A-14-1B-EE-D1
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : fe80::a47a:3af7:72e6:f899%11(Preferred)
       Autoconfiguration IPv4 Address. . : 169.254.248.153(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.0.0
       Default Gateway . . . . . . . . . :
       DHCPv6 IAID . . . . . . . . . . . : 348662292
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-CD-DA-86-10-9A-DD-9F-1D-FF
       DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
                                           fec0:0:0:ffff::2%1
                                           fec0:0:0:ffff::3%1
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Wireless LAN adapter Wireless Network Connection:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Atheros AR938x Wireless Network Adapter
       Physical Address. . . . . . . . . : 10-9A-DD-9F-1D-FF
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter 6TO4 Adapter:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft 6to4 Adapter
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{077AEF3E-6752-42C5-A037-9FB69A17CB27}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{83EF0082-ADD7-4283-8303-9133BD882E39}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{22AA845D-6210-4549-AAE5-3D8917BA7286}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter Teredo Tunneling Pseudo-Interface:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter isatap.{D364C869-F7DD-4F9A-ADBA-7EBF53DD21D2}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes

    Are you using a MacBook Pro? Is everything installed on the same drive?
    I would love to know how that install was performed. When I install Windows under boot camp, my MacBook Pro drive ends up with 4 partitions: Mac, Mac Recovery, Windows, and a small partition that I believe is used by boot camp.
    Installing BitLocker on Windows requires the creation of a new small partition that Windows will boot off. The small partition is unencrypted, while the primary Windows partition will get encrypted. The following post discusses the maximum partition issue: https://discussions.apple.com/message/22753791#22753791
    Has anyone installed Windows through boot camp on it's own drive, and if so, can BitLocker be installed on that without reaching any partition limit? I'm assuming that's possible, but would like to know before I spend hundreds on new hardware.

  • Only IE is able to access the internet; no other applications can access internet

    I recently upgraded my original Hitachi 160GB hard drive on my Lenovo IdeaPad Y510 to a WD 320GB hard drive, and cloned my original hard drive image to the new hard drive using Acronis True Image WD Edition's Disc Cloning utility. I had the utility resize the original partitions proportionally. Everything else seems to have transferred correctly to my new hard drive, but I find that ONLY Internet Explorer is able to access the internet, although I can ping my network printer, the other computers on my home wireless network, and even other IP addresses on the internet such as www.google.com, etc.
    I had removed my previous ZoneAlarm Free Firewall before doing the hard drive upgrade; it appears to have been conflicting with my Mozilla Firefox and Thunderbird applications, causing them to hang up and then not close down properly. I am currently using only the Windows Firewall and Windows Defender, along with AVG 9.0.814 Free Antivirus, SpyBot S&D 1.6.2.0 and Spywareblaster 4.3. I also used to use AdAware Free Edition, but had to uninstall it as I have not been able to update it to the newest version successfully.
    Is there something in the Windows Vista Home Premium OS I have on my machine that might be causing this problem? It is funny that ONLY Internet Explorer is able to access the internet now.

    Yes I do, and even with them checked to allow access (i.e., as an exception), it does not help.  I have tried all of the MS help about the problem, but they refer me to my machine's manufacturer for support, since my copy of Windows Vista came with it.  I cannot even use my DVD NeXtCopy software, as it requires access to the internet too, and even after re-installing it, I cannot activate the new installation because it cannot access the activation server!
    I hope someone can help me.  Upgrading to this new hard drive should not be so disastrous!
    Regards and thanks for trying to help!
    Ray
    vijaysaradhi wrote:
    You are using multiple number of malware removal tools on your system.I would recommend you to go for Microsoft security essentials Its Light on the system resources .Or use any one only...more than one will create false positive messages to come up 
    Next go to control panel-->system and security--> windows firewall-->allowed programs
    Do you see Firefox and the other browsers  in the list of allowed programs? something like this 

  • [SOLVED] Network restart before Arch can access internet via IPCop?

    The Leopard machines on our LAN have working internet on boot, my Arch box does not?
    Even though I have the IPCop server's IP in the Arch /etc/resolv.conf.head file, I still have to do a sudo /etc/rc.d/network restart before I can use the internet.
    Does anyone know how I can solve this one?
    Thanks for your time.
    Last edited by handy (2008-12-13 13:41:04)

    tomk wrote:Post your /etc/rc.conf. If '/etc/rc.d/network start' works but network-at-boot-time doesn't, that's where the error is.
    As a workaround I've put /etc/rc.d/network start in my /etc/rc.local & now I don't have to type it manually.
    tomk wrote:Incidentally, dhcpcd messages don't show up in dmesg - you should be looking in messages.log or everything.log.
    I looked in all the logs that had been changed after a boot.
    Here is my rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # HARDWARECLOCK: set to "UTC" or "localtime"
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_AU.utf8"
    HARDWARECLOCK="UTC"
    TIMEZONE="Australia/Sydney"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # Scan hardware and load required modules at bootup
    MOD_AUTOLOAD="yes"
    # Module Blacklist - modules in this list will never be loaded by udev
    MOD_BLACKLIST=(net-pf-10 pcspkr) ## turns off ipv6 & pc speaker
    # Modules to load at boot-up (in this order)
    # - prefix a module with a ! to blacklist it
    MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore fglrx)
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    HOSTNAME="archtypical"
    # Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
    # interfaces.
    # Interfaces to start at boot-up (in this order)
    # Declare each interface then list in INTERFACES
    # - prefix an entry in INTERFACES with a ! to disable it
    # - no hyphens in your interface names - Bash doesn't like it
    # Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
    ###lo="lo 127.0.0.1"
    # eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
    eth0="dhcp"
    ###INTERFACES=(lo eth0)
    INTERFACES=(eth0)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    # - prefix an entry in ROUTES with a ! to disable it
    # gateway="default gw 192.168.0.1"
    ROUTES=(!gateway)
    # Enable these network profiles at boot-up. These are only useful
    # if you happen to need multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network-profiles
    #NET_PROFILES=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    DAEMONS=(syslog-ng @iptables @network @netfs @crond @alsa @portmap @sshd @transmission-daemon @stb-admin @fam @gpm)# @tor @privoxy # @hal - hal's out on account of worker
    # End of file
    Last edited by handy (2008-12-13 12:30:42)

  • For some reason or another I can access Livejournal on IEx but not Firefox, can someone give me a pointer...

    I'm having a problem accessing my LiveJournal from Firefox, but it's fine when I go through Internet Explorer. I prefer Firefox. Can someone help?

    The similar problem, only this site doesn't open, all the others work correct. The blank page is absolute, the browser seems at all doesn't tries to incorporate to the server.

  • I can use the ethernet connection but not the wireless on my Airport Extreme to connect to the internet.

    How do I get the wireless to work again? I've turned both the modem and Airport Extreme off and on again. Do I need to do a hard reset on the Extreme?

    Thanks for the reply.  I've only powered down all my devices and repowered them.  When I made the switch from cable to Uverse, at some point my old USB printer connected to the Extreme spit out about 8 documents that were in its queue, and nothing since.  I can see it on the network from my Mac, but my wife's PC can't find it (and that's the real problem, if you know what I mean).  I have a new MacBook Pro, and she's running XP SP2 on her PC.  Everything worked fine when I was on cable modem service, but since I've changed to ATT Uverse, I'v had this little issue.  As you can tell, I'm a novice when it comes to networking.
    Thanks again,
    Bill J.

  • I downloaded iOS 8 and my photo stream disappeared. The weird thing is, when I went to post an Instagram picture, they were all there. So I can access them on Instagram but not from the photos app... Help?!

    i have tried turning photo stream on and off and only a few come back

    In iOS 8 the PhotoStream album is lumped into the recently added photos album. Delete a photo there and you will delete it from your PhotoStream.

  • I have a National Lottery online account but for a while now i cannot access it from my MacBook. I can access it via other pc's and laptops and via my iphone. I have been on to the NL helpline and they say the issue is with cookies and my MacBook. Help!

    I have a National Lottery online account but for a while now i cannot access it from my MacBook. I can access it via other pc's and laptops and via my iphone. I have been on to the NL helpline and they say the issue is with cookies and my MacBook. Help!

    Hi Josh,
    Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
    Thanks.
    Mike Towns

  • Can not access internet via wired connection, wireless working OK

    Background information,Came home from vacation turned on PC to access email.Emails started downloading then stoped,started getting messages that firefox stopped working and Thunderbird quit working and others.My desktop is attached to a verizon router.all my other devices are wireless and are working fine through the same router.I connected my laptop to the lan connection, turned off wifi and accessed the internet via lan connection.Using device manager, checked drivers, says up to date, also says that it is working properly.I have gone to the command line and can ping google.com.I can ping the loop around. ping127.0.0.1I have done the ipconfig/release,ipconfig/renew, and ipconfig/flushdnsipconfig/all indcates that it is there and enabledMy Lan connection is part of the mother board.can not access internet via wiredconnection.Not sure what to do next.Help Please   

    Reply: I spent about an hour last night doing all the things that you suggested including moving the lan cable from my desktop to my laptop which worked fine. When I hoover over the connection it says;  Network3                                                                                        Internet Access   no error messages.When I unplug the cable at the router a red x covers that connection icon.Plug it back in red x goes away.It is seeing the router, just does not appear to be providing selected web page info.Computer thinks it is working fine.

  • I bought a new laptop and can access my itunes library but when i try to add purchased playlist songs to my ipod message appears asking if I'm ok with erasing all other songs on the ipod. Help needed.

    I bought a new laptop and can access my itunes library but when i try to add purchased playlist songs to my ipod message appears asking if I'm ok with erasing all other songs on the ipod. How do I add purchased playlist to ipod without erasing existing ipod playlists?

    cujoftw wrote:
    wow ... I get a headache just trying to read what you just said. I went and read how to migrate my library and found that you can only migrate purchased media.
    No, you can easily migrate your entire library from one working compter to another.
    If you fail to backup or migrate your library and find yourself with nothing but a new empty computer and a device full of content iTunes is designed to only recover the iTunes purchased content, however third party tools can help recover everything if needed.
    tt2

Maybe you are looking for