Other usb adapters

was wondering i have a cisco valet and was wondering if you can use other USB adapters besides Cisco Valet - Connector Wireless USB Adapter? i see a few others on the cisco website and wondering if there compatible with valet?

Yes, you can use other USB wireless adapters with Cisco Valet.

Similar Messages

  • HT2188 I have an iphone 3GS that keeps getting the message "charging not supported by this device" Dismiss I have tried other usb adapters, car chargers, and directly hooked to the computer and still get the error message. Software is up to date as well.

    I have an IPhone 3GS that keeps getting the message "charging not supported by this device" Dismiss. I have tried several different ac adaptors, car chargers and even directly connected to USB on computer and still get the same message. Software is up to date as well. Help!

    Clean the dock connector with a soft dry brush.    

  • Ejecting iPod causes other USB devices to be ejected at the same time.

    When ejecting an iPod Nano 4g from iTunes under Windows Vista, all other USB devices attached to the computer are also ejected at the same time (external hard drives, thumb drives, scanners, etc.). Is there a way to prevent this from happening?

    Express is slow ethernet.. 10/100 only. The max speed of any connection to a USB hard disk is limited severely by the 100mbit..
    USB is always slow btw.. This is actually a poor way to share a drive. A cheap NAS.. ie ethernet to Sata directly is far far superior and a single disk NAS can be had cheaply.. you will never get close with USB in network situations.
    If you use a hub though, you can plug multiple disks into an Extreme.. I guess the network speed is at least no worse than the USB hub -- ethernet devices which are lousy as a whole.
    Never forget you have the fastest ethernet adapters and fastest possible connectors already on computers on the network.. people are so utterly mesmerized by NAS they forget.. a FW800 or better USB3 if you have a newer computer shared to the network from a computer has much higher throughput and is much cheaper than even the very low end network stand alone boxes.

  • Compatible wireless usb adapters

    PLEASE HELP URGENT!
    I am out of town and desperately need to find a " compatible wireless usb adapters" to run off my aunt's Linksys WRTG....old wireless router-she cannot remember her WPA security code?  I am using a MacBook Pro running Mountain Lion.
    I am currently standing at Staples Tech support desk and they are searching too but seem to not be finding anything.

    whuggy wrote:
    I have to introduce a Windows XP box to my 802.11n network served by an Airport Extreme N. Which USB 802.11n adapters work well with Airport Extreme? Please confirm that it has drivers for Windows XP. Thanks.
    Linksys has several 802.11n adapters compatible with the AEBSn.
    Wireless-N USB Network Adapter:
    http://www.linksys.com/servlet/Satellite?c=LProductC2&childpagename=US%2FLayout&cid=1160093476789&pagename=Linksys%2FCommon%2FVisit orWrapper&lid=7678939789B01
    Wireless-N Notebook Adapter:
    http://www.linksys.com/servlet/Satellite?c=LProductC2&childpagename=US%2FLayout&cid=1144763513196&pagename=Linksys%2FCommon%2FVisit orWrapper&lid=1319639789B04
    Wireless-N Business Notebook Adapter:
    http://www.linksys.com/servlet/Satellite?c=LProductC2&childpagename=US%2FLayout&cid=1152745213436&pagename=Linksys%2FCommon%2FVisit orWrapper&lid=1343639789B05
    Wireless-N PCI Adapter:
    http://www.linksys.com/servlet/Satellite?c=LProductC2&childpagename=US%2FLayout&cid=1144763512962&pagename=Linksys%2FCommon%2FVisit orWrapper&lid=1296213404B04
    I personally own the first two, and they work perfectly with the AEBSn. All 4 use the same chipset, so I assume that the last two should work also.

  • Where can I find a list of USB adapters that work in OS X.4?

    My friend is trying to get his Mac up and running on a wireless network and he has bought a few USB adapters, but they aren't compatible with OSX.
    I tried the Ralink drivers, but it stays connected for around a minute, then drops the connection.
    So, if anyone has a list of compatible USB adapters for OSX, I'd appreciate it.

    Here is the only product update page that I'm aware of at the Adobe.com website:
    Product updates

  • Any working uncertified Lightning to USB adapters for iPhone?

    We used to have all these uncertified lightning to USB adapters that were $1 each (in a pack) from eBay and worked fine, only somtimes giving a warning and working anyway. Slowly, all of them got lost by family members. We have a couple more cables lying around that hardly ever work or only work with certain devices, and one of them is one of those stupid 3rd party ones that are certified and the same price as Apple ones. So I want to know what the status is on these cables before I buy more. Have the newer versions of iOS prevented them from working? Most of us are running iOS 7.0.6 or some version of iOS 6.
    Yes, I know there are certified ones, but they're so much more expensive than the basically equivalent uncertified ones (if they work). I only use my original Apple adapter for syncing with my Mac, and the rest are just for charging, music in the car, and Xcode on the go.

    d00dbro wrote:
    Have the newer versions of iOS prevented them from working?
    As it should, yes.
    Lightning connector is a proprietary Apple product.
    Uncertified means stolen technology.

  • 802.11N USB Adapters compatible with Leopard?

    I'm upgrading the home network, to N and I'm trying to find some N-USB adapters for my Duo iMac that only has G at the moment.
    Thanks for the help.

    Take a look at QuickerTek.

  • How good are the USB adapters with the WRT300-N

    I have a guest house I am trying to fit with interent connection and I felt like
    the WRT300 with thf N network would reach.
    The interenet conection stays connect to the Laptop in the yard...yet once
    inside it looses it's connection. I have the latest firmware installed 0.93.3
    I'm wondering if the USB adaptor on the laptop will keep teh connection inside the house.
    Does anyone have any experience with this??

    are u using the wireless-g or wireless-n usb adapters ? 
    if u are using the wireless - g adapter , access the router ui and go to the "wireless" tab..select the wireless network mode as g-only and radio band - standard channel and wireless channel as standard channel - 11.....
    for the n- adapter , select the mode as n-only , radio band - wide channel , wireless channel as wide channel - 9 and standard channel - 11 ...

  • Anyone try these Firewire to USB Adapters?

    Has anyone tried these FireWire to USB adapters?
    http://www.monoprice.com/products/subdepartment.asp?cid=104&cpid=10314
    http://www.firewiretousb.com/?gclid=CLmQmY6ErJYCFQJ-xgodOT3SzQ
    Could iMovie/Final Cut Express use these?
    Thanks in advance.
    Dave

    I'd also like to know if you can convert USB 2.0 to Firewire. I've seen some hubs around the $40 dollar range, but it is not clearly stated if they will convert, or if they are just hubs.
    I recently bought the new MacBook Aluminum and it has no firewire port. Problem? My external hard drive is firewire. So I can no longer access my backup drive or backup data on that firewire drive without having to jump through some hoops.
    Does anyone have reliable experience transferring data through USB on their Mac to firewire on an external drive? If so... what sort of hub/converter were you using?
    Any help is greatly appreciated. Thanks...

  • Wireless USB Adapters compatible with 10.8

    Since updating to Mountain Lion 10..8.2 on my MBP 2008 - 8 gig Ram, the system will not start up when my USB wireless stick is attached. Once I remove it, the system starts up fine. Pop it back in and it shuts down. I can plug other devices including USB music Keyboard, iphone without any problems. Occasionally I can insert the usb stick and wireless actually works but it is intermittent.
    I use the stick as the wireless hardware inside the MBP is damaged and have been using it like this for around a year on Snow Leopard without any problems. I also updated the drivers for my USB stick which is made by Realtek.
    I repaired disk permissions and reinstalled Mountain Lion before posting this but the problem still persists.
    Does anyone recommend any USB adapters that are compatible with 10.8??
    Kind Regards

    Before you purchase anything, read the system requirements for DW CS6 and DW CC.
    http://prodesigntools.com/products/adobe-cs6-system-requirements.html
    CC Tech Specs
    http://www.adobe.com/products/creativecloud/tech-specs.html
    Nancy O.

  • Shuffle causes Windows to stop recognizing all other USB ports!?!

    When I plug my new Shuffle in to any USB Port, Windows stops recognizing all other USB drives. (this includes my internet connection and external hard drive with all music) If I disconnect the Shuffle and repower the other devices, they work normally again. I've seen this same problem on this forum and the answer did not help - here is the answer/link given the previous posting: http://docs.info.apple.com/article.html?artnum=93499
    The shuffle has its own drive letter on my computer, so no conflict here AND my husband's shuffle works just fine on this same usb port and same cradle. As soon as I eject the working shuffle and place the new one in the cradle, my computer shuts down and no other USB Ports work until I unplug the shuffle and repower the others. Maybe a shuffle problem?
    Thanks for your help!

    The shuffle has its own drive letter on my computer,
    so no conflict here AND my husband's shuffle works
    just fine on this same usb port and same cradle. As
    soon as I eject the working shuffle and place the new
    one in the cradle, my computer shuts down and no
    other USB Ports work until I unplug the shuffle and
    repower the others. Maybe a shuffle problem?
    Thanks for your help!
    Are you "eject"ing your husband's shuffle in iTunes OR are you "safely removing hardware" in Windows?

  • HT4061 got iph 4s; using windows 8; downloaded latest update and iphone software update center could not be contacted or is unavailable......??  disabled firewall, disconnected all other usb devices, still not restoring; any one have any suggestions?

    iph 4s, using windows 8; downloaded latest update 6 for iphone and iphone software update center could not be contacted or is not available; tried troubleshooting; removed other usb connections and restarted computer; still will not connect to iphone software update center; any suggestions?

    I noticed the Windows Firewall Entry in the diagnostics, so I did get that part squared away...
    Windows Firewall is on.
    iTunes is enabled in Windows Firewall.
    Connection attempt to Apple web site was successful.
    Connection attempt to browsing iTunes Store was successful.
    Connection attempt to purchasing from iTunes Store was successful.
    Connection attempt to iPhone activation server was successful.
    Connection attempt to firmware update server was successful.
    Connection attempt to Gracenote server was successful.
    Last successful iTunes Store access was 2013-11-07 17:52:33.
    Still unable to detect the iPhone though.

  • Trying to restore iphone 4 on Windows 7, 64-bit. It goes so far and then stalls. Have updated itunes, unplugged other USBs. this is my fourth attempt. Any suggestions?

    Trying to restore iphone 4 on Windows 7, 64-bit. It goes so far and then stalls. Have updated itunes, unplugged other USBs. this is my fourth attempt. Any suggestions?

    Disable your firewall and antivirus.

  • IPhone causes problems on other USB devices?

    Is anyone having problems with external USB hard drives or any other USB peripheral when his iPhone is connected to a Windows PC or sometime after that?
    I'm having some problems with external USB hard drives when the Windows system is continuously hammering them for more than a half-hour. The problem is not easily reproducable, and I don't know the cause.
    It probably has nothing to do with the iPhone. But one possibility I have to consider is that the iPhone draws enough current (or something else I haven't thought of) that interefers with the USB communications.

    What I meant in my previous post was that the USB wouldn't allow the iPhone to draw more current than the USB can safely provide, unless it was defective. I have an external hardrive, a wireless mouse, my printer and my iPhone connected directly to my laptop's USB ports and have not seen any problems with any of them. In several years of using USB devices, I've not seen any problems that I could assign to the USB ports/controllers... they just seem to work all the time. Will be interested as to your findings.

  • Shuffle doesn't get along with other USB drives

    Okay, so I purchased a new iPod Shuffle, and upon connecting it to my computer and installing all the software, I nearly had a heart attack. According to Windows Explorer, all my data on my 80 gig USB hard drive and my 1 gig flash drive had been erased. I unplugged the flash drive and plugged it back in, and Windows told me it had no idea what to do with that device.
    Long story short, I've determined that it's the Shuffle that's causing it. If I plug in the Shuffle, Windows stops recognizing my other USB drives. If I disconnect the Shuffle and repower the other devices, they work normally again. The Shuffle has its own drive letter, so it's not a conflict there. Any ideas?

    Same problems here. (-50 erros when trying to autofill and -1480 errors when attempting to Restore) I have two other iPods and they sync fine. I'm also having the same hang-up problems once I plug in the Shuffle and try to either Restore of Autofill. I successfully managed to load songs once after 40 minutes of work. Now, nothing. I've tried absolutely everything.
    Please fix this!
    Kent

Maybe you are looking for

  • Error message when I try to start the SC SM Console

    Hi, i get the following error message when I try to start the SC SM Console in TN MSDN Virtual Lab Message: Failed to connect to server 'SCSM01.contoso.com' Microsoft.EnterpriseManagement.Common.UnknownServiceException: The service threw an unknown e

  • BP address move in CRM 5.0

    Hi Friends, There is a functionality of BP address move in CRM 5.0 Here we can move the source BP address into target one. I created one contract using the source address. After this i created a new target address for BP and now i am trying to move t

  • Depreciation Run executed for a period but no posting found

    Dear Experts, I have checked a few of the FA in the Fixed Asset Master, and confirmed that they have not been depreciation run yet for period "2009-02". My current period is set to "2009-02" as well. But when I tried to run depreciation run for "2009

  • Oracle 11g R2, Problem Loading Spatial Data

    We have a geodatabase which has been implemented by oracle spatial. it has been working quite fine since 2 years ago. Recently the data center serving our geodatabase has been upgraded on both software and hardware specifications. The handler applica

  • Is sth. like "JCO.Repository.getFunctionTemplate(String BAPI_NAME)" in NCo?

    Hi guys, I switched from JCo to NCo and try to find the same functions that are available under JCO. My specific problem is this: I integrated SAP in our applications using XML with JCo until now, e.g. JCO.Function.getImportParameterList.fromXML(Stri