Other uses for the USB?

Since the new Extreme has hard-drive capability, does this allow for other usb data transfer such as iPod sync or the ability to scan from a printer/scanner combo? Just what exactly are the limits of this USB port?

I plugged in my usb flash memory and it works as a disk. You should try again. Are you using Airport Disk Utility? Set it to auto discover and show on menu bar.

Similar Messages

Other uses for the zen micro H

I read about people removing the hard dri've from the zen micro -and using it in their digital slr cameras that can take CF micro dri'ves...
is this possible? could you remove the hard dri've - and put it into a CF slot on a notebook and have it show up as a 5gb dri've?

Here's the answer i guess
From:
http://www.steves-digicams.com/microdri've.html
A Note From Seagate
"The Seagate hard dri've inside these players was manufactured and qualified for use specifically in these music player applications. It is not designed to be removed from the music player, and removing the dri've voids the warranty on the music player and on the hard dri've.
Also important to note: because these dri'ves weren't designed or tested for uses external to the music players, they may not operate correctly (either short-term or long-term) in other applications.
To date, Seagate has not completed the design and testing of, and has not made available, a -inch hard dri've for use by consumers in CompactFlash slots.
Seagate is working on a consumer version of its -inch CompactFlash Type II hard dri've, the "Seagate CompactFlash Photo Hard Dri've," that will be priced very attracti'vely for the mainstream photography market. Seagate announced this dri've in June 2004. We'll have more news regarding a launch date later in the holiday season.
Best to you and to everyone at Steve's,"
John Paulsen
Sr. Manager, Corporate Communications
Seagate Technology

Currently, I have 5 iPads used for the same purpose. Since similar data /application is shared among all of them, is it alright for me "Backup" only 1 iPad. And in which case, if anything happens to any of the other iPads I can still recover the data

Currently, I have 5 iPads used for the same purpose. Since the same data /application is shared among all of these iPads, is it alright for me "Backup" only 1 iPad instead of all 5? And if anything happens to any my iPads which I have not backed up, I can restore it from the iPad where I have save the Backup. I am hoping by doing so, I will also be able to save some icloud storage space. Let me know if my question is still not so clear to you guys. Thanks.

Hello PeachY1234,
If I understand correctly you'd like to save iCloud storage space by only backing up 1 of the 5 iPads to your account since they are all going to have very similar data and usage. You certainly can do that, but I do have to warn you that any unique data between them would be lost if you had to restore from that one backup made on another iPad so just keep that in mind. If you do need to restore in the future you can use this article to restore that iCloud backup:
iCloud: Restore or set up your iOS device from iCloud
Thank you for using Apple Support Communities.
Cheers,
Sterling

I have used all the usb ports on the back of my iMac desktop [2009] - in one I have a hub - too many?

The longer I have had my 2009 desktop iMac, the more I am needing usb ports. I only have 3 on the back. Currently 2 are used for the 2 printers I own and the other has a 3 branch hub in it for my mouse, keyboard and card reader. I have the mouse and keyboard attached this way as the cords work better for me in my workspace. I am using one of the ports on my keyboard for my mp3 player. Now I am branching out into the computer world and have tried using a flash drive. However when I tried plugging it into the other usb port on my keyboard, I get the message that there isn't enough power to support it. Same message when I tried one of the three ports in my hub. So the only way I could get my flashdrive to work was to unplug a printer, plug in the flash drive till I was done with it and then plug in the printer again. Since I am sure that this plugging and unplugging constantly would not be a good thing, I am now contemplating getting a better hub so I could permanently have a usb hub open for my flash drive. I figure I can always use a port on my keyboard for my card reader as I don't use that very often. My question is: "If I do get a better hub to put on my 3rd port on the back of the computer, will that be too much for the poor thing?"

Generally, you should use hubs (of which the keyboard is one) for devices which don't need to get their power from the USB port ("bus-powered"). Portable drives (including flash drives) are bus-powered; printers and other larger devices which have separate power cables are not. So the printers should attach to your hub, and small devices should connect directly to the Mac.
Now, some hubs are actually powered themselves, and these are better suited for powering small devices.
There are some good options here:
http://eshop.macsales.com/search/usb+hub
Are both your printers USB-only, or can they be networked (either wired or wirelessly)? That would save you some ports.
Matt

Help! My iPod touch won't let me download any apps. A message keeps coming up saying "This Apple ID cannot be used for the iTunes store. Please enter another Apple ID" I changed my ID to see if that would work but the same message still comes up.

Help! My iPod touch won't let me download any apps. A message keeps coming up saying "This Apple ID cannot be used for the iTunes store. Please enter another Apple ID" I changed my ID to see if that would work but the same message still comes up.

Where are you physically located?
What country's Store are you using?
The two have to be the same and the payment method for your account also has to be associated (billing address, where iTunes gift card was purchased) with that country.
Has the ID(s) worked before for purchases for this country's store?

Report to Generate Materials Used for the Production of FG/SFG Materiak

Dear Experts,
I am working for a Cement Factory. CLINKER is a SFG used for the production of FG Cement.
RMOPCK1 and FINECOAL are another SFG used for the Production of CLINKER
RMOPCK1
+ = CLINKER + (Different Materials) = CEMENT
FINECOAL
For CLINKER we will create process order every month similarly for RMOPCK1 and FINECOAL.
RMOPCK1 is using 5 Raw materials and FINECOAL is using 1 raw material
Limestone + Silica 1 + Silica 2 + Bauxite 1+ Ironore 1 = RMOPCK1 and
Rawcoal = FINECOAL
All the raw materials, SFGs are used for creating different variety of cement.
I want to know for a certain period how much is the CLINKER produced and How much is the raw materials used for producing the CLINKER.
When i try through KOB1 with the process orders for CLINKER it is giving me total usage ofr RMOPCK1 and FINECOAL for producing the CLINKER.
I Want to know for ex:
the quantity of raw materials (Limestone + Silica 1 + Silica 2 + Bauxite 1+ Ironore 1 )used for producing ex: 1000 TON of CLINKER.
Please help. Thanks
Edited by: simonjohn on Oct 9, 2011 6:46 PM

Thanks

My Snow Leopard 10.6.3 has Safari 4.0.4 but this cannot be used for the new features of iTune. I tried upgrading to Safari 5.1.7 but it needs Snow Leopard 10.6.8. Where can I get a version of Safari 5.1 that is compatible with Snow Leopard 10.6.3?

My Snow Leopard 10.6.3 has Safari 4.0.4 but this cannot be used for the new features of iTunes. I tried upgrading to Safari 5.1.7 but it needs Snow Leopard 10.6.8. Where can I get a version of Safari 5.1 that is compatible with Snow Leopard 10.6.3?

Hi..
here can I get a version of Safari 5.1 that is compatible with Snow Leopard 10.6.3?
Not possible. You need to update to v10.6.8
Click your Apple menu > Software Update
Or update using the this download > Mac OS X 10.6.8 Update Combo
Then restart your Mac.

Software needed for the USB device, "USB Interface Controller TEST2.0"

My mother recently acquired a digital camera. She acquired it from a second-hand store, which did not include an interface cable or software. The manual (and the USB port on the camera) indicates that a male-male USB cable is necessary for photos to be copied to the hard drive.
I was not successful in locating such a cable at any local electronics store (I assume such a cable is now out-of-date). I purchased one from a seller on eBay. The brand is "e circuit electronics".
Upon powering up the camera with the cable connected to it and the computer, the following message appeared:
"Software needed for the USB device "USB Interface Controller TEST2.0" is not available. Would you like to look for the software on the Internet?"
I clicked "Yes". After an approximate two-minute wait, another message appeared stating:
"Software Update is not able to connect to the Internet. Please check your configuration and try again."
I deleted, "Software Update Preferences" in the Preferences folder inside the System Folder, without solving the problem. How do I solve the issue of allowing Software Update to connect to the Internet?

Thank you for your continued assistance, BDAqua. Unfortunately, the driver you linked to does not seem to be compatible with the camera. It is a driver for the V20 model, whereas my model would correspond to be a V2755, as referenced from a list of other Vivicam models when during a search at the Open Drivers web site.
From the system requirement about the card reader you gave me, it will not work, as this system is running 9.1. I am hesistant to upgrade this computer to 9.2, as I have experienced system unstability with that version, with even the 9.2.2 update applied.
In the mean time, I have e-mailed Vivitar regarding this issue, but have as of yet received a reply.
I am not certain as to other specifics to give you, in order to solve the Software Update problem. Please elaborate.
Yes eww, the computer in question is able to fully connect to the Internet for all that I need. I am fully aware of the difference between a computer connecting to the Internet, and a computer connecting to a digital camera. I have 15 years of Macintosh experience.

When syncing with itunes, got error message saying had error and now ipad2 will not do anything other than showing the USB cable with arrow pointing to Itunes on screen. have done the reset and restart, but still get same thing.

when syncing with itunes, got error message saying had error and now ipad2 will not do anything other than showing the USB cable with arrow pointing to Itunes on screen. have done the reset and restart, but still get same thing. Ipad does not show up in itunes even though cable plugged in. Have shut down and restarted Windows 7 computer.

I had done all of that to no avail. I did call Apple Tech Support and after he suggested I try a USB port in the rear of the Win 7 computer, things starting working again. I had tried switching the USB port at the front of the machine but that had not helped. Everything is good to go again. thanks for your reply

Is it possible to print from iPhone 4 on a non wireless printer via use of the USB data / charging cable

Is it possible to print from iPhone 4 on a non wireless printer via use of the USB data / charging cable.

No

My movie has clips that have some extracted audio that I would like to use for the menu music in iDVD 11. Does anyone know how to do this? Copy and paste does not seem to work.

My iMovie 11 movie has clips that have some extracted audio that I would like to use for the menu music in iDVD 11. Does anyone know how to do this? Copy and paste does not seem to work.

I would use Quicktime Pro.
See: QuickTime Pro: How to Extract or Disable Tracks at http://docs.info.apple.com/article.html?artnum=42596 and QuickTime Player 7 Help - Extracting, Adding, and Moving Tracks at http://docs.info.apple.com/article.html?path=QuickTime%20Player/7/en/c3qt6.html
To get Quicktime 7.6.6 for Snow Leopard see: QuickTime Player 7.6.6 for Mac OS X v10.6.3 at http://support.apple.com/kb/DL923 (Quicktime 7.6.6 is the latest version.)
To upgrade to Quicktime Pro see: QuickTime Player 7 Help - Getting QuickTime Pro at http://docs.info.apple.com/article.html?path=QuickTime%20Player/7/en/c2qt.html

I recently bought a new macbook and installed Acrobate Pro. My settings/preferences did not come over and I do not have the same style options for my signature. It now only allows me three options and the style I have been using for the last year is not

I recently bought a new macbook and installed Acrobate Pro. My settings/preferences did not come over and I do not have the same style options for my signature. It now only allows me three options and the style I have been using for the last year is not there. How do I add additional options and get my preferred signature style back?

Hi Amanda ,
Which version of Acrobat are you using?
Which signature style are you talking about?
You can go ahead and try uninstalling and reinstalling it and see if that works for you .
Use the cleaner tool to uninstall it .Here is the link.
Download Adobe Reader and Acrobat Cleaner Tool - Adobe Labs
You can refer to the following link to re install it .
https://helpx.adobe.com/acrobat/kb/acrobat-downloads.html
Regards
Sukrit Dhingra

What font is used for the menu of Illustrator CS5?

What font is used for the menu of Illustrator CS5?
I know how to change the default font, which is used to input characters.
But, I do not know how to check the font used in the menu.
Is it the font that is described in the following files?
C:\Users\[UserName]\AppData\Roaming\Adobe\Adobe Illustrator CS5 Settings\ja_JP\AIPrefs
If you know, please tell me how to check the configuration file and how to change the font that is used in the menu.

If your using windows xp and applied the 12.02 update, then this is a known bug in
the update effecting xp users and adobe is working on a fix.
see this thread
http://forums.adobe.com/thread/762392?tstart=30
MTSTUNER

What data is used for the link title in osssearchresults.aspx

In our OOTB SharePoint installation we have a search results page in a collaboration site that displays Word documents. Each word document has a Title property, however the text used for the hyperlink to the document in the search results page does not seem
to use the Title property, instead it uses some text from inside the document, e.g. the contents of the first H1 tag.
I had a look at the XSL of osssearchresult.aspx core results web part, and this uses a "title" parameter. So I can only assume that when SharePoint search catalogues a Word document, it decides to ignore the title property of the list item
and instead derives the title text from content within the document itself.
Is that correct? Or am I missing something? Can I change the title for Word documents in search to be the actual title of the list item?

Hi,
The word documents have two columns “Name” and “Title” by default. The “Name” column is the file name and is “file” column type, its related Crawled Property is ows_LinkFilename
. The “Title” column is the document title and is “Single line of text” column type, its related Crawled Property is ows_Title . When SharePoint Search crawls the word document, both the two columns are crawled. However, the ows_Title
crawled property is mapping to “Title” managed property, but the ows_LinkFilename crawled property does not map to any managed property. In the SharePoint search results, the word document shows its “Title” managed property.
So for your scenario, the search result should show the “Title” column value. Please go to your document library and verify the “Title” column’s value of your word documents.
For more information, you can refer to the thread:
https://social.technet.microsoft.com/Forums/sharepoint/en-US/4e1749cd-cf4d-46d6-98e2-3f42366e376e/how-does-the-search-result-are-displayed?forum=sharepointadminprevious
Best Regards,
Eric
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

Is there a simulator for the USB-6009?

Is there a simulator for the USB-6009 that I can download and install? I installed the disc that came with the board, however, no simulator.
Thanks,
Chris

Hi
You could simulate diferent device in Measurent and Automation Explorer (MAX) but I don't see there your modul USB-9009.
There are odere module, but not this module.
Regards
bogdani
Polish LabVIEW Center - www.labview.pl

Other uses for the USB?

Similar Messages

Maybe you are looking for