Out of Frequency Problem with Apple Multiple Scan 720 Display and Mac mini

If a resolution with a horizontal and/or vertical frequency not compatible with your display, in this case an Apple Multiple Scan 720 Display, is selected in the Display preference pane of the Mac OS X 10.4.10 system running on a Mac mini (Early '06), you will recieve a message on your screen about being "out of frequency" and the power management feature will shut down and restart your display repeatedly. The following solution should restore your display to proper function. It may apply to other displays and Macintoshes running Mac OS X, but it has only been tested specially on this setup.
1. Shut down the Mac mini with the power button (press and hold for 5 seconds)
2. Start the computer up with the Mac mini Mac OS X Install Disc 1 (press the power button, insert the disc, hold the C key down until the progress bar starts up)
3. Click on the language, then select Utilities > Terminal...
4. Type "cd /" and return
5. Type "cd Volumes" and return
6. Type "cd your hard drive name" and return (you need to enclose the hard drive name in double quotes if more than one word)
7. Type "cd Library" and return
8. Type "cd Preferences" and return
9. Type "rm com.apple.windowserver.plist" and return
10. Type "exit" and return
11. Quit Terminal
12. Select Utilities > Startup Disc...
13. Select the OS on the hard drive and click on Restart button, holding down the Shift key until the progress bar starts.
14. Log in to the account that had the display problem in Safe Boot mode
15. In System Preferences select Display, select a resolution with the appropriate frequency, 60 Hz should be fine, then close System Preferences
16. Restart the computer, log in to the account normally, and the display should be functioning properly.
DO NOT SELECT AN INAPPROPRIATE RESOLUTION/FREQUENCY FOR YOUR DISPLAY IN THE DISPLAY PREFERENCE PANE! BE AFRAID, BE VERY AFRAID!
Mac mini (Early '06) Mac OS X (10.4.10) Apple Multiple Scan 720 Display
Mac mini (Early '06) Mac OS X (10.4.10) Apple Multiple Scan 720 Display

Just a correction and an elaboration:
It should be Startup Disk... with a k, not a c.
Both the resolution and the frequency must be appropriate for your display to work properly. Check your documentation or the manual information available on your display for the appropriate resolutions/frequencies. Evidently the Apple Multiple Scan 720 Display is considered so old that no allowance was made for it in the Display preference pane of Mac OS X 10.4.10.
Mac mini (Early '06) Mac OS X (10.4.10)

Similar Messages

Multiple Scan 20" on a Mac mini ?

I want to make a low expensive change of computer.
Is that possible to connect a Multiple Scan 20" on a Mac mini ? (Multiple scan have a DB-15 connector)
Thanks.
Claude

Yes, with a DB-15 to VGA adaptor it should be possible.
Mac mini G4 1,42/512/80, PowerBook G4 12" 1,5/1,25/80 + 23" ACD Mac OS X (10.4.7) as well as iMac G4 17" 1,25/2/320, PM G3 DT 500/576/20 + 17" Syncmaster 710T

When I hook my ipod to computer it reads: there is a problem with this drive scan the drivenow and fit it (F) it doesnt work

when I hook up ipod up to to itunes it reads: IP F There is a problem with this drive. scan the drive now and fix it. When I do this, nothing happens.

Hello,
I found the same issue. I have an iPod Classic 160 GB (Black) bought in April 2013. I'm using a Windows 8 Laptop bought in August 2014.
This is my account of this problem and why I think customers should just ignore the pop-up, but Apple (and possibly with Microsoft/Windows) should look at the issue.
Recently (approximately from early February 2015), when I connect the iPod to my computer I get a message saying there is a problem with the drive and it needs to be scanned and fixed. In full the message reads:
There's a problem with this drive. Scan the drive now and fix it.
This message appears very shortly and then immediately (once the message disappears, is clicked on, or x-d) brings up Windows File Explorer on the drive and its containing visible folders: which tells me nothing (though it can clearly open it and look at the files not locked to iTunes)
Other than this, the iPod seems to connect properly and work fine. iTunes (ver: 12.1.0.71 64bit) seems to find no issue. The iPod runs fine, it syncs properly (all of my music and podcasts). It responds as it always has and works for hours.
I did some troubleshooting: first on the wire, trying all ports and using an alternative, then on my laptop (all usb ports with other connectors and device drivers) and some basic testing of the iPod and iTunes. All of these seemed fine to me, no issue whatsoever other than the message every time I connect the iPod. So I just ignored it for a while.
Anyway, eventually I got curious (and had some more free time to look at it) and let Windows 8 do what it wanted (scan and fix the drive). Clearly the iPod works fine, and I have nothing important on it that isn't on my computer, so at worst Windows will break the software and I'd have to reformat the drive through iTunes (and Restore to Factory Settings) which I feel fine doing. I also took note of all of my settings on the iPod (like EQ, and the way I laid out the menus etc...) so I can redo those from defaults.
Prior to doing this, the iPod was version 2.0.5 (the latest version).
When I set the drive to be scanned, windows told me it identified the problem and would fix it. I don't remember the exact wording, as this message was immediately obscured by a pop-up telling me the drive was in use and software using it should be closed. So I closed iTunes which in turn caused the pop-up and message to disappear.
Windows then said it had succeeded and brought up the File Explorer of the drive again (now with some folders missing). When I loaded iTunes back up, it told me there was a problem with the iPod and it would need to be restored. Ejecting the iPod showed that it seemed to believe it had no content on it.
So I restored the iPod through iTunes, downloading the latest iPod update again and started syncing the iPod. After adding a couple songs, I ejected it and played them - they worked fine, the menus had returned to defaults but I quickly changed them to how I liked and overall the iPod is back to how it was. I've now set it to sync the remaining thousands of songs (and couple hundred podcasts). Edit - by the end of this post, this has finished copying Music, Podcasts, and Playlists. It's back to exactly how it was before.
Annoyingly, this has not removed the pop-up message when I connect the iPod, still the same as before - the most irksome thing being the file window opening every time i connect the iPod, though this is still minor (I just have to remember that this will happen and manually close it each time).
So I'm at a loss on the cause, and am going to return to ignore it. I'd greatly appreciate if Apple could look into this. I'm wondering if it is a recent update to iTunes or to Windows, but I don't trust that I won't be able to undo changes if I myself began looking through them (and I lack the time and expertise to do that effectively). I think there might be that Windows is detecting something in the way that Apple formats their iPod drives that it believes is an issue (even when it isn't). My guess is the way of formatting is unchanged (the iPod hadn't received an update recently to suggest and alteration to this) but maybe the things Windows is looking for may have slightly changed and disagrees with Apple's way of keeping the iPod Drive proprietary to iTunes.
TL,DR: Advice to others (and Ljchicago) searching this topic is to ignore the message for now.
Thanks,
Dixavd

Problem with sound in rented itunes series on mac mini (2010) hdmi

Hello,
I just bought the new mac mini with HDMI. It is connected via HDMI to my receiver Denon AVR 3310. The receiver shows that it has "multi channel in" on the display.
I made all the configurations so that i can watch dvd an the mac mini. When i play a movie with Dolby Digital the receiver does show that on the display and playback is possible without any problems. All my 5.1 speakers play sound.
The big problem is with iTunes. When I want to watch rented series from iTunes Store, for example Dr. House, only 2 speakers of my 5.1 are used. And when I change to surround in iTunes I can only hear static noise.
What is the problem? What is wrong with iTunes?
Thanks in advance

I am having the same issue.
I have a Panasonic TH-50PX60U, and a Yamaha RX-V2065. The Mini is plugged into the Yamaha via HDMI and Yamaha to TV via HDMI.
Problem: Just to clarify I do NOT have a video problem. That part seems to be working fine, my problem is with audio. When ever I switch inputs on the receiver or turn the system off (not the Mini, that always stays on) the audio defaults back to the internal speaker in the Mini. I have to go into system settings and change it back to the HDMI audio out. This is super frustrating. I'm sorry if I posted this in the wrong area, but it's the only thread that looked like it might have an answer. Thanks!

Problem with D-Lux 3 raw files and Mac OS X

Hello everybody… my first post.
Last year I purchased a D-Lux 3, which is my first digital camera and my first Leica too.
While I enjoy this little camera, recently I have noticed that all my pictures shooted in raw have at least 4 black pixels in the exactly same position.
I’m using Mac OS X v 10.4.10 (last version) on a new MacBook 2.16 GHz and the dead pixels appear using both Preview and Aperture (trial). While at first I thought to have a defective sensor, making additional trials, I found out that if I shoot in JPEG or if I open the raw files with Adobe Camera Raw the pictures are just fine, no “dead” pixels appear.
I’m wondering if other D-lux 3 and Mac OS X users have ever noticed this kind of problem.
Is it some sort of very strange bug in Mac OS X?
Thanks

Thanks everybody for the answers.
The pixels are in the top part of the frame but not on the edge.
I think the best explanation could be the automatic “dead Pixels” correction pointed out by jrg_uk.
I really didn’t know some applications make this kind of automatic corrections.
I guess at this point I need to have my camera sensor repaired by Leica.

Problems with installing SL Server on pre installed Mac Mini

Hi,
I have brame new Mac Mini (Snow Leopard preinstalled) and now I'm trying to install Snow Leopard Server on it.
The problem is, that after choosing the HDD in the installation procedure, the system says that installed OSX is newer then the one I'm trying to install and that I should choose other HDD!
What should I do?
Regards,
M

Hi,
start up from cd, start installation, choose "disk utility" from the menu bar, erase hd (journaled),
after this you can install OSX server.
Good luck,
Rick

Anybody Had Success with Hype Tape-to-MP3 converter and Mac Mini?

I bought this Hype thing to upload all my cassettes to my Mac Mini, and be able to burn CDs. Downloaded the Mac App for it, but haven't been able to make sense of the directions. Many complicated things on the window when I open it. I do what the booklet says, but get nothing. Anyone else have one, with success? Please let me know? Thanks.

Sorry.
I bought it many years ago. But here's where I bought it and this looks exactly like what I have.
http://www.martelelectronics.com/91.html
It's a Martel HGM-1 High Gain Mic.

Activation problems with Apple TV 3 rd gen and the latest version of YouTube for Apple TV

Since the latest version of YouTube for Apple TV you need to connect your iPhone Youtube account to your Apple TV for Youtube to use a personal account. It does this through youtube.com/activate. I have two Apple TV and have implemented the process the same on both. After that, everything works fine in about 12 hours, or as long as the Apple TV is "awake". Then, randomly, I have to once again carry out the activation process to use my personal Youtube account on my Apple TV. I consider this to be a big failure and a clear deterioration of YouTube for Apple TV. Does it really have to be this way? Why does my Apple TV forget the "pairing"? All of my devices (iPhone 5, Apple TV gen 3, latest software) are on the same wireless network.

I don't have an answer for this, unfortunately. I've even had my Apple TV replaced (yesterday), and after about an hour of normal operation, it now fails to connect to servers, or connects intermittently and poorly, and it can no longer connect to the iOS Remote app. These are the exact symptoms that prompted the Genius Bar to replace the original unit.
Either there is a basic flaw in Apple TV, or I'm extremely unlucky. All my other Mac and iOS devices have positively no network problems. Very frustrating.
WiFi is provided by a late-model AirPort Extreme.

Having some problems with Apple Pro Res 422 HQ and Hard Drives

Hey,
I've been having trouble when digitizing video via Apple Pro Res 422. First off I'm using a macbook pro 2Ghz intel core duo/2GB of Ram and my hard drive is pretty much almost full. I've set my scratch disks to a Lacie 1TB drive via USB 2.0. Second of all during the Apple Pro Res 422 capture process in the middle of capture it says that my Internal Drive is almost full and won't let me continue on with capture. I don't get it because everything in the scratch disks are set to my Lacie Drive.

My Lacie has 1 firewire 400 and 2 firewire 800 ports but my computer is an early macbook pro that only has 1 firewire 400 port and 2 USB ports. So yea it kinda of stinks but could you recommend a eSata Express card?
Message was edited by: Final Cut Pro 4.5

IDOC to JDBC, problem with the multiple line items structure and mapping

Hi,
I have a scenario where the ORDERS data need to update the SQL table. for the idoc which consists one line item its ok but for multiple line item its just updating one line item. In the destination side we have only one table for purchase order which consists of lineitem as a field.(no different tables for Header data and Line item data)
Can anyone suggest me how to create a structure for target side and how to map them.
Regards,
CJ

Hi Rajan,
The table structure is
[PO_DATE]
      ,[VENDOR_NO]      ,[PAYMENT_TERM]      ,[MATERIAL_CODE]      ,ORDERED_QTY]      ,RECEIVED_QTY]
      ,[UOM]       ,[RATE]       ,[CURRENCY]       ,[PO_EXCRATE]       ,[TAX_CODE]       ,[BASE_VALUE]       ,[TAX_VALUE]
      ,[TOTAL_VALUE]       ,[ADVANCE_PAYAMT]       ,[TOTAL_QTY]        ,[SNO]       ,[POLINEITEM]
Datatype structure:
PO_XI_MT_ORDERS05 1-1
STATEMENT   1-UNBOUN
TABLENAME 1-1
    ACTION   optional
    TABLE    1-1
    ACCESS 1-1
       PO_NO   0-1
       PO_DATE 0-1
Correct me if im wrong.
Regards,
CJ
Edited by: kuncjy on May 5, 2011 11:32 AM

Problems with ipod synching between pc desktop and mac laptop?

Has anyone had any problems trying to synch their ipod in both a windows desktop version of itunes and a mac laptop version of itunes? if it is all ready synched with windows will it be compatible to synch to a mac laptop?
thanks

Click here and follow the instructions; Windows formatted iPods can be synced by the Mac version of iTunes, but not have their firmware updated without a restore except in the case of the iPod shuffle.
(27767)

Apple Multiple Scan 1705 - usable with modern video cards?

I still have an old Apple Multiple Scan 1705 display which I've been using continuously since ~1995. Even though I don't have a Mac anymore (I know, I know, mea culpa), I hooked it up to my PC and it has worked great. But, I recently received a newer hand-me-down PC from my sibling. It didn't come with a monitor, but I thought that would be OK as I could just switch the monitor from my old system to the new system.
As it turns out, it's not that easy. When I boot it up, the monitor goes blank after POST, usually between the XP screen and the welcome screen. Sometimes I can actually get as far as seeing the desktop, but the screen usually goes blank before I can navigate anywhere. It works fine in safe mode, though. From what I've read on the Web, this would appear to be an "infinite loop" problem, where the OS and the video card stop speaking to each other.
I may be on a fool's errand here, trying to combine a PC video card (an NVIDIA GeForce 7600 GS) with an Apple monitor which is ten years older than it. I've done some basic troubleshooting, such as reinstalling the video card drivers and visually inspecting the hardware and connections. But I wonder if it is even possible for the two to communicate properly. For the record, I'm running Windows XP SP3. Has anyone else been foolish enough to try this?
My girlfriend hates the bulkiness of this old CRT monitor and wants to get a flat panel anyway, but while I save up for that, it would be nice to be able to use the new computer with the old monitor. Even if it won't work, I've gotten 13 years of use out of the monitor, so I certainly got my money's worth. But I thought I'd check with the community and see if there's any life left in the old display.
Thanks for your help!

In Windows XP, in order to change the resolution for the monitor, you have to right-click on the desktop and select "Properties". This bring up "Display Properties". From there, you click the "Settings" tab. This gives you some basic options. For a wider selection of resolutions and refresh rates, click on the "Advanced" button. Then select the "Adapter" tab and press the "List All Modes" button. This lists all the available configurations for resolution, refresh rate, and colors. I fiddled around with these, trying all of the configurations that were supposed to work according to the Apple Multiple Scan 1705 specs. Unfortunately, anything other than VGA 640x480 60Hz would cause a "blue screen of death".
My girlfriend had indicated that she wanted to get a flat panel display anyway (to get back some of that desk real estate), so I decided to cut my losses and buy a new monitor. Unfortunately, I now have the exact same problem with the new monitor. So, it seems the problem is not with the monitor after all. Or, at the least, that's not the only problem. Once I resolve what other hardware/software issue is going on, I'll see if the 1705 display will work. But for practical purposes, you can consider this question resolved.
Thanks for entertaining my obscure question.

I am having same problem with apple tv need 4.4 version and can not find solution this a brand new product out of box yesterday why would it not already have updated version. I am getting frustrated that I can not get this mirroring icon to work. I

I am having same problem with apple tv need 4.4 version and can not find solution this a brand new product out of box yesterday why would it not already have updated version. I am getting frustrated that I can not get this mirroring icon to work. I have tried all suggestions in this thread and nothing works. I also hooked up to laptop through iTunes with micro USB nothing!!!

The new appletv software came out 2 or 3 days ago, how would Apple get it on the device in the box in a store?
Why don't ou update the appletv software?

Is there a problem with Apple Mail using IMAP

Is there a problem with Apple Mail using IMAP? Having a problem syncing to our mail server: doesn't sync properly when multiple devices use same mail acct. Spoken w/ mail hosting provider who says Apple Mail doesn't follow IMAP protocol properly leaving Apple Mail users to experience a variety of problems when connecting to IMAP accounts. Among them:
- Improper syncing
- Proliferation of drafts during composition of an email.
- Connections on the mail host do not close automatically and proliferate over time until the host rejects further connection requests.
Hosting provider goes on to suggest turning off IDLE command. In my experience turning this feature off did not improve the situation. In fact, it created a few.
Question: Is the hosting provider correct in faulting Apple Mail?
Been fielding the question with a number of people. I'm aware of three people who are experiencing similar problems, each using different mail hosts. Tech reps at inmotionhosting.com and nexcess.com point the finger at a Apple Mail, along with an IT specialist in Los Angeles, CA, and a tech support rep at an Apple Store in Arizona who said that Apple and Google mail are aware of and coordinating to resolve the problem.
Anyone out there have any insights into this?

Is there a problem with Apple Mail using IMAP? Having a problem syncing to our mail server: doesn't sync properly when multiple devices use same mail acct. Spoken w/ mail hosting provider who says Apple Mail doesn't follow IMAP protocol properly leaving Apple Mail users to experience a variety of problems when connecting to IMAP accounts. Among them:
- Improper syncing
- Proliferation of drafts during composition of an email.
- Connections on the mail host do not close automatically and proliferate over time until the host rejects further connection requests.
Hosting provider goes on to suggest turning off IDLE command. In my experience turning this feature off did not improve the situation. In fact, it created a few.
Question: Is the hosting provider correct in faulting Apple Mail?
Been fielding the question with a number of people. I'm aware of three people who are experiencing similar problems, each using different mail hosts. Tech reps at inmotionhosting.com and nexcess.com point the finger at a Apple Mail, along with an IT specialist in Los Angeles, CA, and a tech support rep at an Apple Store in Arizona who said that Apple and Google mail are aware of and coordinating to resolve the problem.
Anyone out there have any insights into this?

In my Iphone 5, Nothing on my App Store is working its displaying blank (Except for Genius section). I've tried to uninstall and install itunes and all its component but still it doen't fix. Not sure if its problem with apple servers. Someone help please!

In my Iphone 5, Nothing on my App Store is working, its displaying blank (Except for Genius section). I've tried to uninstall and install itunes and all its component in my desktop but still it doesn't fix the app store issue. Not sure if its problem with apple servers. Someone help please!

settigns>itunes and app store to make sure you are signed in.. If you are, you will see your account name..... anyhow, click your account name, sign out and sign back in
also go to to settings>general>reset and reset network settings... if that doesnt work settings>general>reset and reset all settings!
one of those shall work. The last step would be to restore your device (apple.com/support) HT1414

Out of Frequency Problem with Apple Multiple Scan 720 Display and Mac mini

Similar Messages

Maybe you are looking for