Output Device FTP

Hi All,
In SPAD there is output device FTP defined by SAP. I am trying to use this output type to send report output to FTP server.
When I run the report, I choose option List--> Print. In the pop up box I can enter printer name or E-Mail or FTP.
Does anyone know what is the configuration setting in SPAD for FTP output type? Do I have to enter a command that will trigger the FTP server.
Thanks and Have a great day.

Do you mean your optical drive is not listed? What is listed…for example, Hard Drive?
What are your system specs?
Russ

Similar Messages

Help, no sound, no sound output devices

Hi all,
I tried this over in the Tiger section with little help. About a week ago I told my grand-daughter she could plug her iPod headphones into the headphone jack on the the front of the G4. Now, I have no sound at all except for through the headphones and only the headphones show up as an output device. I have tried trashing the "com.apple.soundpref.plist" and rebooting thinking that the OS would creat a new one during startup but that didnt work (there was TWO of them in there). I also tried trashing "com.apple.audio.AudioMIDISetup.plist" but that didnt help either. I put them both back where I found them later. Those files both belong in library-preferences right? I tried zapping the Pram but having no sound I didnt get a "bong" I just listened for it to rev-up twice, still no change. I also tried the PMU reset switch. I can change the volume level with no effect except for the headphones and the sound is not muted.
System Profiler does not recognize apple pro speakers that are plugged in, I do have sound sticks to try but they are boxed up in the garage.
So I am wondering if the phone jack got messed up by the iPod plug, a hardware issue, or does this seem to be software related problem? I did an archive & install today with still no sound so now I am thinking that the plug is messed up inside and still thinks the headphones are plugged in.
Does anyone out there have any advice to offer?
I am going to do surgery next to explore the headphone jack and the tiny speaker above it.

Slimtech,
I don't have a solution for this, but maybe some comments might help a bit...
com.apple.soundpref.plist and com.apple.audio.DeviceSettings.plist should be at /Library/Preferences.
com.apple.audio.AudioMIDISetup.plist should be at ~/Library/Preferences.
The "Audio (Built In)" section under System Profiler for my QS G4 shows no attached devices, but merely shows information about the sound card itself, with three generic outputs listed as "Internal Speaker, External Speaker, and Headphones".
Normally, you should get a startup Chime from your internal speaker even with headphones plugged in, unless perhaps the sound setting is on Mute at shutdown, which sometimes will affect/mute the startup chime at the next startup.
I would think that if the Mac thought that the headphone were still plugged in after removal, your Sound Preference Pane Output window would indicate this. If the Headphones appear in the Output window when plugged in, then disappear when removed (refresh the window by clicking another Tab then going back to the Output Tab), the System obviously recognizes their removal. Apparently, it doesn't recognize the internal speaker that it's supposed to switch back to though, for reasons unknown to me.
You might try vigorously and repeatedly plugging/unplugging the headphone plug into the headphone jack, which helped clean up the jack and restore the sound on my G3 some time back.
Sorry I couldn't be of more help.
Gary

Help! No Audio Output device is installed

My speaker in bottom right for My sound say "No Audio Output Device Is Installed" and i have tried to go through many things to solve such as go into device manager and enable or update through there etc...to no avail.
I stumbled across a thing that worked for most people. Recovery Manager. but. I don't have it on my computer to try so i have no other options to turn to. Can someone please help on how to fix this issue

Dear Customer,
Welcome to the HP Consumer Support Forum!!
To isolate the issue please perform the steps below:
1. Restart the computer.
2. Check the Sound icon in the taskbar.
3. If the icon has an X in the lower corner, click the Sound icon in the taskbar or
4. Right-click the icon, and then click Troubleshoot sound problems.
5. The audio troubleshooter checks for sound problems. When the troubleshooter finishes, it displays the results.
6. If the computer has sound, the issue is resolved.
Install Original Realtek High Definition Audio Driver from the link below:
http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-Slimline-s5000-Desktop-PC-series/3942804...
From the above link click on Driver-Original > Original Realtek High Definition Audio Driver > Download and install the same.
In case the issue still persists and if the audio was working fine earlier, you may perform system restore to previous working condition using the steps mentioned in the link below:
http://bertk.mvps.org/html/restoresysv.html
Hope this helps, for any further queries reply to the post and feel free to join us again.
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
GR1
Although I am an HP employee, I am speaking for myself and not for HP

HELP ASAP! no audio output device installed with hp pavilion dv2500

product name: hp pavilion dv2000
model number: dv2710us
product number:2CE75228LJ
windows vista home premium 32bit
my hp keeps telling that have no audio output device installed and theres the the image for volume with a large red circle with a white x in it.
this is not true because i have contexant (i think that's what it is called) speakers installed.
Lately when i would restart my computer the sound would work intermittently but for the past two days whether i restart my computer or not the image for volume with a large red circle with a white x in it is still there and says no audio output device installed. PLEASE HELP!
This question was solved.
View Solution.

Hi, you can try the below steps to resolve the issue :
Step 1 : Re-install audio drivers from HP Recovery Manager.
1. Click Start, in the Start search box, type recovery . Then click Recovery Manager .
2. In the Recovery Manager window that displays, click Next. On the Reinstall software programs that came with your computer screen, click No, I would like to see other options . Then click Next .
3. In the Reinstall hardware drivers screen, click Yes . Then click Next. On the Welcome to Hardware Driver Reinstaller screen, click Next .
4. In the driver list, select the name of the sound adapter installed on the system. Then click Next. When complete, the Reinstallation is complete screen displays. Click Finish to restart the computer. After the computer starts, test for sound. If the issue persists perform step 2.
Step 2 : Re-install audio drivers manually
If there is no sound and the error still displays, update the audio driver from the weblink below :
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-63129-1&cc=us&dlc=en&lc=en&...
Step 3 : Restart the Windows Audio Service.
1. Click Start , type services.msc into the search field, and then select services.msc from the list when it becomes available to open the Programs window.
2. Scroll down to and select Windows Audio , right-click to open the drop-down menu, and then click Start .
3. Right-click Windows Audio , click Properties , and then verify that Startup Type is set to Automatic .
Restart the Notebook and check for the issue.
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Help Please!! no audio output device installed?

Hi. I have a satellite A215-S4757 last night I installed some windows updats went to bed because it was going to take awhile. When I got it had finished and was in sleep mode. When I turned it on I noticed the sound was on mute. Or I thought it was. When I attempted to turn the sound on I recieved the message "No audio output device installed". I updated BIOs 2.30 but that didnt work. If anyone could help me out I would greatly appreciate it!
Thanks

Try this! Looks like you have Realtek audio. I was having the same problem until I installed the updated Realtek driver directly from Realtek site.
As many users have posted, I was having this problem with my Satellite L505-S5990. I tried most of the suggestions I could find here and on the 'net to no avail. I was surprised to see that this problem affected many laptop brands - even as far back as Windows XP!!
Last week I think I finally found the answer (or at least Realtek did). My laptop has Realtek HD audio, and the drivers that came with laptop seemed to be the culprit. I checked the Realtek site last week, and they have an updated driver, dated 3/30/2010, for Windows 7 as well as other versions of Windows. It is Version 2.46.
I downloaded and installed these drivers, switched back to going into sleep mode rather than hibernate and - so far - the computer wakes from sleep with sound intact!!!
Hopefully these drivers will work for others.

Audio icon in upper right menu disappears and there is no sound Went to Apple preferences which says there is no output device. I can't figure out what to do. Help!

There is a sound icon in the upper right menu which disappears and reappears. When it disappears there is no sound. Went to Apple preferences for sound preferences. When the sound icon is off, this page is not active. Says "mute" is activated and that there is no output device. Cannot fix this problem. How do I retrieve the sound icon and get sound back?

Hi Ronnie, anything in particular going on when this happens?
Long shot, but...
Next time it happens... Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there, some things will change it for their own use, then not set it back

How can I get my audio input and output devices back? I have no sound and cannot see any of the devices in Audio MIDI Setup..??

Hi, I tried to set up a new output audio device on my mac that would have multiple outputs (iBox Twist speaker and my internal speaker) but when I went to click onto one of the iBox Twist (there were 2 options available: iBox Twist and iBox Twist Stereo), Audio MIDI Setup crashed and when I finally got that back open, I found that there were no audio input or output devices to be found. My sound is working, as when I turn on my iMac, the starting sound still plays, however the volume control in the menu bar is no longer a black colour, but grey and when I try to change the sound on my keyboard it does not change. This already happened to me once, and after 3 hours I managed to fix it very simply (switching off Mac, unplugging power cord, leaving for 15 seconds, plug power cord back in and switch Mac back on, holding Alt, Cmd, P and R keys until you hear the Starting Up sound twice) however this same technique that fixed it once before is not working this time and I am still stuck without sound. I have tried Repair Permissions, rebooting in Safe Mode, Hardware Test and checking for Software Updates. Has anyone else had this problem and managed to fix it?
Thanks in advance for any help anyone can give me!

In case anyone has had the same problem as me, I have just managed to fix this by doing the following:
Switch off Mac
Switch back on in Safe Mode (Hit power button, then hold Shift key until a loading bar appears at the bottom of the screen).
Switch off Mac again
Remove power cord and wait 15 seconds
Plug power cord back in and hold down the keys alt, cmd, p, r all at the same time until you hear Starting chime for a second time and hopefully your audio will back.

Test report to check output devices?

Hi,
Is there a test report that will print a page so I can check if the output device is working OK and printing like it should? I have create a output device with a device type but now I would like to check if it's configured OK. Is there something I can print to check that? So resolution, margins etc.
Thanks!

Hi,
Just go to SM50 and press the printing icon there. Is not a large report but you can see the resolution and margins there.
Hope this helps you.

Could not turn on Screen mirroring. The output device is not ready or does not support HDCP

i tried it on my tv sony bravia w700b with my new xperia z1
i didnt unlocked my bootloder or i didnt rooted my phone
dont know whats the problem is
'Could not turn on Screen mirroring. The output device is not ready or does not support HDCP'. can anybody able to tell how can I resolve this please?

Have you checked if your device does support HDCP? I looked at https://www.iezvu.com/ezcast.php?l=en but i'm afraid i can't find any detailed specification for it.
If you have unlocked your bootloader this may also be the cause for this issue.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Background job step - Printer - Output device table

Hi,
When creating background job, printer- output device also specified for every step. Which table to check for job name and output device combination ?
Thanks.

Hi Raj check table TBTCP

Is there a way to have Firefox respect the default audio output device when it has been changed while Firefox is open?

I have been a Firefox user for many years and I still use it as my primary browser. One problem that has bothered me for years is the fact that when Firefox is open and I change my default audio output device, Firefox doesn't respect that change and continues playing audio through the device that was originally being used. Even if you stop the audio and continue playing, the output device doesn't change.
Is there any way this can be configured in Firefox? Now if I listen to music online (e.g. Soundcloud) I always use Chrome since it's respects the default audio output device change even while in the middle of playing audio.
Reproduce:
1. Start playing audio (e.g. from a YouTube video; HTML5 and Flash are affected)
2. Change your default audio output device
3. Audio will continue to play from original output device
Thanks!

This is the same issue that has plagued me for years. I always thought that this was a Flash plugin issue, but it does occur on HTML5 as well. A friend of mine verified that this does not occur in Linux, but only on Windows. It would be great to have this fixed, as it's honestly the only thing that's making me use Chrome all the time, as I don't want to have multiple browsers open.

How to use airplay speakers in multi-output device without crackling audio?

Hi,
I would like to mirror the audio output from my mac mini to the built-in output and an airplay speaker.
Therefore I added a Multi-Output Device containing the Built-in- and Airplay output, as soon as I activate the airplay speaker the sound is mirrored but unfortunately always with a crackling sound coming of the speakers set as "slave Device"... only the Device set as "Master Device" has clear sound, doesn't matter if it's the airplay speaker or the speaker (or headphone) directly connected to the built-in output.
I've tested this with a mac mini and an mac book air as audio source, same problem. Both were running Mac OS V. 10.9.2.
Does anyone have an idea what I'm doing wrong?
Greets
Chris

I'm using a 2011 Macbook Pro running Mavericks and current Apple TV (MD199HK/A 3rd generation) when trying to output audio to both Apple TV and built-in output simultaneously I suffer crackling and popping. I have this issue once I use Audio MIDI Setup (under utilities) to create a Multi-Output Devise. Once I use this multi-output devise made up of Apple TV and Built-In Output to get my music to both output devises at once BUT I get crackling sound on either Spotify or iTunes.
I've worked around this issue by using AirParrot. I select Apple TV in AirParrot with Audio enabled. The Apple TV then takes all audio output, then I select the 'Multi-Output Devise created in 'Audio MIDI Setup' and I have playback through Apple TV and Built-In Output without any crackling or popping.
Only minor outstanding issue is that whatever scenario I then run Audio Midi Setup in terms of setting various devises as Master Clock and resampling of sub devise I can't perfect the sync between Apple TV audio output and my local Macbook Pro, but close enough with the slightest hint of echo. Plenty of forums discussing Word Clock sync which is out of my league. Un-ticking drift correction on the 'AirParrot' audio output has them close enough, depends on how easily you can hear your apple TV output from the room where your Macbook Pro is and vice versa.

Apple TV worked until today. Message says unsupported signal check your output device. I have checked hdmi cable with another device and it's fine. Put on a different tv and same message. Went out yesterday and bought a new Apple TV and same problem.

Apple TV worked until today. Message says unsupported signal check your output device. I have checked hdmi cable with another device and it's fine. Put on a different tv and same message. Went out yesterday and bought a new Apple TV and same problem.

Which TV do you have.
You may wish to try the following:
Press and hold the menu and the up button simultaneously on the remote for six seconds, the Apple TV should then begin to cycle through the various resolutions available to it at 20 second intervals.. If you see a picture appear up on your screen, use the remote to scroll down to the OK option and select it.

No longer able to mute or change playback output device for capture.

I have no preview button to turn off in my capture window and have instead gone into the FCP preferences to change the playback output device to something other then my Fireface800 IO device, such as the built in output so that what's being captured only comes out the little speaker in the tower.
Thus I am free to work on other stuff. (8 core mac pro, gobs of ram, multitasking has never been a problem, even while capturing HD.)
But as of the latest update (I keep all my apps up to date), capture plays through the System default device no mater what the FCP setting. So with out a mute button for the capture, I'm screwed.
I'm screwed because I have to Mix down an EP while I capture 26 hours of conference footage at the same time. Obviously, I can't mix properly with that chatter playing loudly over it.
Apple said I have to reinstall because there's no preview button and there should be but I am curious if there's any other way (because it's a huge pain in the *** and tends to screw up other things) and I would like to know if the way I usually do it is broken for other people, so I know if I can upgrade to the latest version again because it was some goofball problem with the framework that reinstalling fixed or if not because that's a bug in 7.0.3
1. Choose one audio output (say, Built in Line Output or your default sound card) everywhere that matters in the Final Cut preferences for Audio output, including Audio Playback Output which is what I've been using to switch this for, gosh, years probably just out of habit.
2. Log and Capture, capture some footage from tape. (I happen to be working with a basic HDV firewire profile.) What device do you hear output from?
3. Stop capturing... and, if you wish, for good measure, close the capture window.
4. Go back to FCP preferences, now choose a DIFFERENT audio output, say, Built In Speaker Output.
5. Try to capture some footage. Is the sound coming out of the built in speaker now?
IS THERE ANY OTHER WAY TO QUICKLY SILENCE THE AUDIO FROM FCP DURING CAPTURE?
Thank you.

excuse me, not linksystem, its a verizon FIOS wireless router & modem as part of the package. i was thinking my old setup.
new system...cant edit my posts....?

How can you choose which audio output device to use?

I currently have my system set up to have two different active audio output playback devices, Speakers and Headphones. By default, applications play on the default audio output device, which is set to Speakers on my computer. However, I am wanting to play iTunes on my Headphones output while all other applications are running on the default Speakers output. In Windows Media Player, there is a dropdown to select which output device the application streams to. Is there a way to make iTunes do this, either in the Preferences menu, by using a plugin, or installing a third-party application that overrides which output applications use?

Under Utility you will find the Configurazione MIDI Audio.app The name is in italian on my Mac but you should find it in your system language. The icon is a Piano Keyboard.

Output Device FTP

Similar Messages

Maybe you are looking for