Output device is not type sapwin

Hello SAP Gurus ,
i am trying to print the dunning letter and i am getting the error "output device XYZ is not type SAPWIN".
I did look up in the forum for the appropriate answer but could not find one .
Has anyone else gone through the same error .
any suggestions and solutions please
thanks in advance ,
Sumit

This is message TD429 (note: providing the message number (we usually can't know) is useful to search forum and sap notes).
Is that custom code which prints the dunning letter? Check that it doesn't force the device type.
This message is also triggered when you try to reprint a spool to an output device whose device type is different from the original device type.
Otherwise report this error to SAP support.
For more information, see Note 528802 - xxx output device does not have a yyy device type.

Similar Messages

  • Could not turn on Screen mirroring. The output device is not ready or does not support HDCP

    i tried it on my tv sony bravia w700b with my new xperia z1 
    i didnt unlocked my bootloder or i didnt rooted my phone
    dont know whats the problem is
    'Could not turn on Screen mirroring. The output device is not ready or does not support HDCP'. can anybody able to tell how can I resolve this please?

    Have you checked if your device does support HDCP? I looked at https://www.iezvu.com/ezcast.php?l=en but i'm afraid i can't find any detailed specification for it.
    If you have unlocked your bootloader this may also be the cause for this issue.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • CUA: SCUG - Transfer Users errors with Output Device does not exist

    Greetings,
    I'm currently setting up CUA on our ECC 6.0 boxes and ran into an issue when I run SCUG and try to transfer the users. We're in the process of upgrading to ECC. The target systems are upgraded copies of our current 4.7 target systems.
    Currently we have CUA connecting to our DEV,TEST, PreProd, and Prod Systems.
    The output devices only reside on the target systems. There are no output devices on our production CUA box.
    I'm trying to setup the ECC CUA box and modeling all the settings to our current environment. Once I set the CUA setting, including the RFC's and ALE connections I ran scug and ran into the issue.
    I only get the error where the Default Output Device is populated. Users with no Default Output transferred without any issues. I looked up notes in OSS and can't seem to find any on this subject.
    Side note: If I remove the output device it transfers without error. Obviously this is not a solutions, I was merely testing out the scenario.
    Any help would be greatly appreciated

    Hi Alex,
    there is just a little comment in SAP note #399917 (point 4).
    As from my knowledge, the SCUM settings are not considered during SCUG. So setting
    'output device' to local will not be a solution.
    The standard way is to transport the ouput device information to your CUA-master system before taking over the users. (create transport in  SPAD).
    I have also another workaround for you gurus, but this will need to modify the standard coding for the time of taking over your users. Using this modification, only a warning message will appear and unknown printers will not be taken into CUA-master system.
    Pls test this proposal carefully (coding is rather old....), this is just a suggestion !
    Include LSUUCF01                                                 
    FORM DEFAULTS_CHECK                                              
    Spool: Ausgabegerät                                            
      IF NOT DEFAULTSX-SPLD IS INITIAL AND                           
         NOT USER_DEFAULTS-SPLD IS INITIAL.                          
        SELECT SINGLE * FROM TSP03 WHERE PADEST = USER_DEFAULTS-SPLD.
        IF SY-SUBRC <> 0.                                            
          PAR1 = USER_DEFAULTS-SPLD.                                 
          CALL FUNCTION 'BALW_BAPIRETURN_GET2'                       
               EXPORTING                                             
                    TYPE       = 'W' "'E' "Warning instead of error                                                                               
    CL         = '01'                                
                    NUMBER     =  29                                 
                    PAR1       = PAR1                                
              IMPORTING                                              
                   RETURN = ERRORTABLE                               
               EXCEPTIONS                                            
                    OTHERS     = 1.                                                                               
    APPEND ERRORTABLE.                                         
        ENDIF.                                                       
      ENDIF.                                                         
    I strongly recommend to undo this modification after you have finished SCUG.
    Good luck, b.rgds, Bernhard

  • Output devices list  not appearing completely in the drop down list

    Hi,
    I have a query where I am not able to see all the 583 output devices in the drop down list of output device for a transaction code whereas I can see all the output devices in SPAD. Can anyone tell me the reason for this?
    Thanks.
    Brijesh

    Dear Brijesh,
    You can show all the value, click on the restriction button, then change the max numbers of hits to 10000,then you can list all the data in drop down, as per i know in standard it will only give you 500.
    Regards

  • I'm trying to record in Adobe Audition and it keeps saying my the sample rates for my input and output devices do not match.  How do I correct this?

    I'm trying to record in Audition and it keeps saying my sample rates for the input and output devices don't match.  How do I fix this?

    I finally have communication between the ISA One and Audition. I moved the optic cable to another SPDIF on the computer and from the SPDIF to ADAT on the ISA One and it finally agreed that the communication was at the same clock speed. The audio was not intelligible so I moved the optic cable back to the original configuration and I can record voice that is clean.          

  • Output Device Selections Not Available?

    Finally have upgraded to a DLT 7000 and now - in DVD Studio Pro 3.0.2 under the General Tab - I am not getting any destination options for outputting.
    Any clues? I am using a Atto SCSI card and with Atto have already determined the drive IS being recognized by my computer - just NOT DVD Studio Pro.

    Never mind.
    Here's the answer if anyone ever needs it.
    The out put device selection is under Advanced Formatting.
    I was told it would be in the "General" Tab, so I was just looking at the inspector.
    Upon opening up Advanced Format - the DLT Drive magically appeared. Just like Lucky Charms.

  • The sample rates of the audio input and output devices do not match.

    I am trying to record line-in audio and keep getting this error.  have a realtek sound card.  I have tried everything I know but cannot record.  please help if you can, thanks.

    Setting the Sample Rate in Windows Vista and 7

  • Output device - POSTSCPT

    Dear Experts,
    We are getting the following error
    when printing the remittance advice we are getting the error "output device is not type POSTSCPT"
    Please advice.
    Thanks
    Balu

    Hi
              Was the correct device type specified in the output device definition?
          To do this, call transaction SPAD, or choose Tools  u2192 CCMS  u2192 Spool  u2192 Spool Administration . Enter the name of the output device in the Output Device field on the Devices /servers tab and choose enter. On the next screen, choose Goto u2192Device Type.
    Regards

  • Output device not automatically determined in VF02

    Hello gurus,
    My default output device is not coming automatically when I add an output type in VF02. This is an issue because output type has requirement 62 set in output procedure, therefore it will not be added until invoice is release to accounting. Futhermore, we have implemented Argentina eletronic invoice, which won't allow to change the invoice once it has been released to accounting. Quite a contradiction. So I'm hoping the output type will be added by condition technique while releasing to accounting, yet i believe since the output device is not being automatically determined in the background, it won't do.
    Any ideas?
    Thank you very much.
    JP

    Hello guys,
    I had checked all your suggestions before posting this thread, but still the issue remains:
    - VV31 condition records are fine but I cannot set a single output device since it will be used for many output devices.
    - Analysis was carried in VF02 and the condition is being picked up but since requirement 62 is set in the output procedure, which forces the billing document to be first released to accounting, the condition is being removed:
    - Printer is set in the user profile options, but does not come as default in VF02
    Thank you all.
    Kind regards,
    JP

  • Output device not changing in Spool

    Dear Fellows,
    I am having problem in the printing of purchase contracts. Users want to keep the output proposed in contract creation in pending status and keep on using it through ME9K by trial  print out.
    Original output is proposed with output medium of printout OK. Now if I change it to output medium fax in ME9K and do a trial fax it does not work. SP01 shows the original printer as output device and not the fax machine.
    I am not sure where the problem is. Please help why output device is not changing when the output medium is changed ?
    Tkx
    IMJ

    Dear,
    When in NACE tcode, you must be selected Application EV, then select output types button. Then select the output type for Fax->then branch to detail , go to default value tab: then you''ll find transmission medium.You can select "fax" or "external send".
    If you're using external send, u need to maintain the "communication strategy"in
    IMG-Application serverbasis servicesmessage controlDetermine Comm.Strategy,then name it and maintain the comm,typethen select the comm.method=fax.
    Regards,
    w1n

  • Output device type

    Hi All,
    To get the print of a PO one device type is getting selected, but we came to know that we need to select another device type so that we can take the printout of the PO with out any problem. But i am not sure where to change the device type in the PO.
    Thanks,
    Raju

    Hi Raju,
    You can change the device type using transaction SPAD - Spool Administration.In here select Output devices and select the printer which you are using to print the PO, then change the device type.You may need the necessary authorization to do this.If your output device is not listed, then you can create a new one. For a list of device types, see SAP Note 8929 in the SAP Service Marketplace.
    Award points if found useful.
    Thanks,
    Praveen

  • For m.type 261 goods issue output device need to be configure

    Hi All,
    As above said in the subject line is there any way to configure output device for m.type 261 goodsissue
    I want to configure output device only for m.type 261 not for other m.types so kindly let me know the configuration settings.
    regards
    sapmm

    The configuration steps are under:
    IMG \ Materials Management \ Inv. Man. and PI \ Output determination . . .
    Condition Tables
    Access sequence
    Output Types
    Procedure
    You want a small Requirement (an ABAPer could create in minutes) for your Procedure that limits the output according to Movement Type 261.
    Regards,
    Nick

  • Output Device settings for Dot Matrix Printers.

    Hi Experts,
    I've made a page format according to Dot Matrix paper.But at that time of print,system is showing an error message that your output device is not support to this format.
    So,how to define Dot Matrix Printer Setting (Wep LQ DSI 5235) in SPAD?
    Regards,
    Prashant Sharma.

    Hi Prashant,
    I believe that the page format that you are using in the SPAD for the Output device must have configured with the Device Type as well.
    Click on the full administration in the SPAD and then attach the page format to the device type.
    Might this will fix your issue.
    Pleasce check the reference link:
    How to configure a page format in SPAD.
    Regards,
    Abhi

  • '$' in output device

    Hi!
    What does in mean when the output device starts with '$'?
    Thanks!

    Hi SS,
    Here is a screenshot from an output condition record.
    When I checked in table TSP03, the output device is not there. I also tried testing the output device using SO10 but it says output device is not defined.
    BR
    Cholen

  • Update termination Error : Maintain Output device in User master record

    Hi All,
    For transaction IW32 when print is given we have getting Update termination error : Maintain Output device in User master record.
    I have set the user_settings = Space, for output_Options passed the output device . Even for control_paramters I have passed the device while calling the Smartform . However there is no use. Still I am getting the update termination error.
    Please let me know how to solve this issue. Any OSS Note is there for this.
    Thanks in Advance!
    Regards,
    Preethi G

    Hi,
    Thanks for the reply. There is no problem in the print program .
    In the user master record , if the output device is not given and in the print program if we pass the output device. the error is coming.Is there any way to solve the issue at the print program level with out maintaining the user master.Please let me know.
    Many Thanks!
    Regards,
    Preethi G

Maybe you are looking for

  • Service desk message view from ECC

    Hi I have following queries regarding service desk in solution manager. 1. Do user need to login into solution manager to see his message status or can he directly see it from ECC. 2. When a message is created through satellite system support message

  • Fatal error while filling connection pool

    I was not getting a connection to an Oracle database and I was getting the following error in cms.log: "FATAL  Connector - Unable to create connection pool for T_Orbis_Oracle: Fatal error while filling connection pool for jdbc:oracle:thin:@MESDB:1521

  • Iphone - reorder control not appearing

    I have a table view,in a table view controller on a navigation controller stack. in cellForRowAtIndexPath: I'm setting cell.showsReorderControl = YES; but when I call [tableView setEditing:YES]I get the delete control but no reorder control (running

  • Is there a way of preventing actions from continuing?

    I have some interactivity built into my slide which involves the user doing a fair amount of clicking. (The majority of these are 'Increment $$variable$$ by X). But it keeps continuing each time the learner clicks which means they skip to the next sl

  • Parse error in DocumentBuilder

    I try XML data parsing with dtd. It is processed normal when DTD file is in full Ascii path. But Error occurs when DTD file path have multibyte character. I trace this process. probably MalformedURIException occurs in initializePath method of com.sun