Output print at out of the window

Hi All,
I'm facing some problem when print the output. After i run the program, the output is print at out of the window.
Could someone advise?
Thanks,
Alice

If you could see the layout correctly in the print preview but it gets truncated/ prints outside the window when you actually print it then it might be the problem with the printer settings also. The printer setting defined in transaction SPAD might be one of the reasons. Check with the BASIS team what are the margin setups relevant for the printer on which you are trying to print.
Cross check by printing on some other printer. If the results are not good, then try and check the dimensions of window in SAPscript.
And since it is SAPscript make sure that you do a client copy after you make the changes for dimensions, incase the developement client and testing client are different.
Regards,
Rinkesh Doshi

Similar Messages

  • Help before I throw this printer out of the window!!!!!!!!!!!!!!!!!

    I have just purchased a Deskjet 2540 all in one printer - I will only ever need to print boarding passes etc. -
    this looked so good on Amazon ideal for my iPad and said how easy to set up!!! In my dreams - I have now spent 10 hours
    Trying to set this up and last night was close to cracking:-
    I am setting this by wirless. I have the password and the printer showing on my iPad.
    Each time I try and load the softwear I am told an unexpected error has occurred please try again later - I
    Have tried and tried to no avail. Apple staff have said I do not need this softwear????????
    The network test results say:-
    1 check the printer network name ssid matches your wireless router network name ssid exactly!!!!!
    2 if they do not match exactly, run the wireless setup from the printer software to configure your hp printer!!!!!
    But no where can I find how to do this and sorry I really do not understand what this means.
    Reading Amazon some people have set up in 15 min!!!!
    The cost of bringing in an expert to set this up is worth more than the printer cost!!!!!!
    Thanks for reading feel better letting of steam will defiantly be a 0 from me for the feed back to Amazon

    Hello SueJon,
    Welcome to the HP Support Forums!
    I hope this reply finds you with the printer not thrown out of the Window. Regarding the Deskjet 2540 setup to work with the iPad, I would like to help.
    There are two ways that you can print from the iPad to the 2540. The first, Wireless Direct. Wireless Direct is a network that the printer broadcasts and the iPad would connect to it. This method will leave the iPad with no other network access while connected.
    Second, and more functional, is having the printer connected to the same network that the iPad is connected too.
    In order to setup this connection, follow the steps outlined below;
    Turn Wireless Direct on from the front panel button on the printer. (number 4).
    Connect the iPad to the printer network, Settings> Network> HP-Print-2540.
    Open Safari and type this I.P address into the address bar, 192.168.223.1 and hit Enter.
    Go to Network or Wireless and then Wireless Setup Wizard.
    Select your network and enter the needed information.
    Once connected, the Wireless light should be solid, connect the iPad back to your network. To print, open a document, hit the Share button (), and if an option to print is available you will be able to select the print option.
    I hope you find this information helpful.
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Can Reader pick up the Default Page Size of a printer that is not the Windows Default Printer?

    We have a web based application that generates PDF documents via Crystal Reports.
    We are using Adobe Reader 8
    The PDF pages are displayed within an Internet Explorer window where the the users then print the document.
    The application is designed so the user only gets one chance to print the document (ie they cant come back and change printer settings if they happen to print the document out incorrectly)
    The document needs to be printed on A3 paper, full duplex.
    We have a printer set-up decidated to the printing of the documents generated by this application.  The default page size of this printer is set of A3.
    If we set this dedicated printer as the Windows Default Printer we have no problems at all.  The default page size (A3) is picked up and the document is printed correctly.
    If any other printer is set as the Windows Default Printer (eg one that has a default page size of A4), the users must obviously select the correct printer from the Print Dialogue Box -however when the user selects the dedicated A3 printer, the page size remains as A4 (page size of the Windows Default Printer).  This means the user must remember to change the paper size to A3 each time.
    Out users find IT a struggle at the best of times - anything that makes the process simpler is very welcomed!
    Is there a way to ensure the default page size of the printer is respected when that printer is not the Windows Default Printer?
    Thanks!

    No.

  • Tried to connect my messages from my phone to my macbook, but the accounts tab under preferences won't let me type in my Apple ID and I can't save, cancel, or exit out of the window

    I just got a new MacBook Pro today. My friend explained to me how to connect my messaged from my phone to my Mac, since they weren't connected yet. I opened Messages > Preferences > Accounts. My Apple ID and account info was already there and it was enabled, but the messages still weren't syncing, so I disabled it and tried to add the account again. I went to put in my account info, but I realized there was no space to put in my Apple ID, even though it said to. I typed in my first and last name, password and country, but when I clicked "save" nothing happened. The section that asked my ID, name and password disappeared, the "save" button keeps flashing, and I can't "cancel" or exit out of the window. If I press "cancel", an alert message appears but all it says is "(null)". How can I fix this so that I can exit out of it? It won't let me shut down because of this.

    It will only sync with new messages received after Mac's Messages is configured and running.
    It will not synced old messages.

  • Please help before i throw my laptop out of the window!!!!!!!!  :-)

    OK, so I have been surfing the net for help/solutions but to no avail...
    When I try and burn a disk from itunes on to a blank disk i get the 2131 error which judging by the ammount i have seen written about it, is VERY common.
    I am about to throw my laptop out of the window as I cant fix it and am have just spend my Christmas itunes vouchers on downloads!argggggggghhhhhhhh
    My cd driver is SN-S082H ATA ???? please does anyone have any ideas what i can do??????
    Many thanks, in advance! Jen.

    Since the issue really is not related to the focus of this forum...compatibility issues between Mac OS and Windows, you should 1. Try a different brand of discs. 2. Post your question on the iTunes forums: http://discussions.apple.com/category.jspa?categoryID=150 3. Post your question on a Windows forum such as those at http://www.windowsforums.org

  • Like an idiot, i bought a game for an ipad and only have a macbook air. can i somehow get the game to play on my air? or have i just thrown $5.29 out of the window?!?

    I recently bought a game for an "ipad", (thru itunes), when I only have a MacBook Air...I had seen where you could switch apps back and forth between devices, ad I thought I could do this. Is there a way to play the game on my Air laptop? Or did I just throw $5.29 out of the window? One more thing...it involved Facebook, and I don't belong...or want to belong!?
    I want to play Jeopardy, Wheel of Fortune, etc. ON MY MACBOOK AIR!?!???

    No way to play an iOS game on a Mac presently.
    I suspect if you contacted Apple's Customer Support and explained the situation they would refund or credit your account.
    SCR

  • Make view transition in/out of the window

    I have a UIViewController that holds three different views via a segment button at the top.
    I want one of the views (first segment) to transition in and out of the window when clicking a button.
    Is this possible at all?

    You can either use a NavigationController to do that automatically for you.
    or
    Read the CoreAnimation Programming Guide and search for kCATransitionFromLeft or kCATransitionFromRight.

  • How to avoid that the last column in a datagrid increase the width out of the window?

    I have a datagrid with this configuraction:
    <DataGrid.Columns>
    <DataGridTextColumn Header="Column01" Binding="{Binding Property1, Mode=OneWay}"/>
    <DataGridTextColumn Header="Column02" Binding="{Binding Property2, Mode=OneWay}"/>
    <DataGridTextColumn Header="Column03" Binding="{Binding Property3, Mode=OneWay}"/>
    </DataGrid.Columns>
    The last column is a description, so the text can be a bit large. so I would like that the width don't be wnough greater than makes the datagrid has a width out side the window.
    For this, I have read that I can use Width="Auto" in all the columns and in the last column width="*", but in this case all the coloumns has a very low width so I can't read anything.
    The code that I have used in this case is:
    <DataGrid.Columns>
    <DataGridTextColumn Header="Column01" Binding="{Binding Property1, Mode=OneWay}" Width=""Auto"/>
    <DataGridTextColumn Header="Column02" Binding="{Binding Property2, Mode=OneWay}" Width=""Auto"/>
    <DataGridTextColumn Header="Column03" Binding="{Binding Property3, Mode=OneWay}" Width=""*"/>
    </DataGrid.Columns>
    I am using visual studio community edition and wpf 4.5.1.
    Thank so much,

    >>For this, I have read that I can use Width="Auto" in all the columns and in the last column width="*", but in this case all the coloumns has a very low width so I can't read anything.
    Can't you just set an explicit width for the first two columns then?, e.g.:
    <DataGrid.Columns>
    <DataGridTextColumn Header="Column01" Binding="{Binding Property1, Mode=OneWay}" Width="100"/>
    <DataGridTextColumn Header="Column02" Binding="{Binding Property2, Mode=OneWay}" Width="100"/>
    <DataGridTextColumn Header="Column03" Binding="{Binding Property3, Mode=OneWay}" Width=""*"/>
    </DataGrid.Columns>
    There is also a MinWidth property that you can use to prevent the columns from being to narrow:
    <DataGrid.Columns>
    <DataGridTextColumn Header="Column01" Binding="{Binding Property1, Mode=OneWay}" Width="Auto" MinWidth="100"/>
    <DataGridTextColumn Header="Column02" Binding="{Binding Property2, Mode=OneWay}" Width="Auto" MinWidth="100"/>
    <DataGridTextColumn Header="Column03" Binding="{Binding Property3, Mode=OneWay}" Width=""*"/>
    </DataGrid.Columns>
    Hope that helps.
    Please remember to mark helpful posts as answer to close your threads and then start a new thread if you have a new question.

  • I used stationery in mail, but now i want to export that email to pages OR print it out without the email headers printing out.  any solutions?

    i used stationery in mail, but now i want to export that email to pages OR print it out without the email headers printing out.  any solutions?

    Hello carolsuz,
    I was researching ways you might be able to save that email to a picture or export it and found this little gem in the iPhone Users Guide, found here: http://manuals.info.apple.com/en_US/iphone_user_guide.pdf about how to take a screenshot.
    Its on page 12 toward the middle:
    Take a screenshot: Press and release the Sleep/Wake button and the Home button  at the same time. The screenshot is added to your Camera Roll album.
    Take care,
    Sterling

  • How to print a message in the Window created out of a Frame Object

    Hello,
    I created a class extended from Thread class
    I want to print a message in Run method : in the Window created out of a Frame Object in the main function.
    I used System.out.println function, but nothing is printed on the screen
    what other function can I use, without using Drawstring method in ie public void paint(Graphics g)Thank you

    Erm...I don't know whether this is acceptable or not, but...if you want to create out of the main frame, why dun u you create a new frame with a button there, so it seems like a pop-up windows (***or like JOptionPane.showMessageDialog)
    P.F.Boy

  • My calendar is blocked. The server has a problem. I am trying everything, but since days I have no access to my agenda anymore. I am about to throw my MacBook Air out of the window :-( How can I solve this problem? My calendar does not react to anything!!

    My calendar is blocked since a few days, while I tried to upload a message in an event. In this weekend, i have not been able to get ANYbody at all online, to help me. I am desperate and feel absolutely idiot. Is anybody out there who can help me?.
    In the website it said:
    1. Open iCal - select "preferences" (I cannot select anything!)
    2. Select "accounts" (I have no clue what to do there)
    3. Re-enter " username and password (Where?)
    4. Exit iCal and start again (I did this, but don't get anywhere near a solution).
    5. Done (cry, cry, nothing changed for days now and I am about to throw everything out of my window :-))
    Thanks for some very useful and easy tips!
    Sjannie Hulsman

    Thanks mate ...
    yes I have an upgraded Iphoto 11 from 9.4.3 ........ unfortunately .... no it didn't solve the problem.  Of course my illiteracy is no help ..... but I did as you suggested and nothing changed at all.  When I highlight a photo I am unable to minimize it and despite changing folders (ie:photos to events) all that happens is that the events folder opens behind the opened photo.  The only solution is to go to "force quit" even though there is no sign to say "iphoto is not responding". and start again ..... very frustrating.  Appreciate any suggestion you have ...
    Nev

  • SOMEONE PLEASE HELP BEFORE I THROW MY MAC OUT OF THE WINDOW!

    Is my setup useless?
    Logic crashes every time I open more than 1 external synth (e.g. predator, massive, ABL2). This occurs with no other instruments in the project.
    It cant seem to take the CPU.
    Here is what I have….
    Apple iMac Intel Core 2 Duo 1.83GHz 512MB (2x256MB) 160GB (upgraded with 2gig of ram – as much as it can take!)
    Logic 7
    OSX 10.4.11
    M Audio Oxygen V8 midi keyboard
    Memory 2GB667 MHz DDR SD RAM
    1.47gb memory free
    92.82gb space free on hard drive
    Can anyone offer some advice? Surely for what I have paid for the system, I should be able to get more out of it than this?…. is there anything else I can do to boost processing power?
    Any help is massively appreciated!

    Hi David,
    Before sleeping out of your window waiting your Imac, maybe I would suggest couple things:
    - Getting LOGIC 7.2.3
    - Getting last M-AUDIO drivers (if lot compliant one)
    - Repair permissions with let's say ONYX software.
    - Are you using external firewire hardrive? (issue for some of Imac sometimes)
    if this still causes you troubles, then you 'll see my face outside your house with my arms ready.
    Cheers.

  • A/V not working...am ready to throw this modem out of the window

    got a Zoom 5560 Ethernet modem/router for my new iMac Intel core duo with built in iSight as the modem i ran on my old imac is not supported (USB OneTouch 330).
    I have done all i can as found in this forum:
    Mac OS X Firewall is off
    Quicktime streaming to 1.5 mbps
    iChat video to none (and also tried various settings)
    Ports open in NAT in Zoom modem/router (4099, 5190, 5193, 5297, 5298)
    Why can't i video chat via iChat, the old USB modem worked out of the box, but obvioulsy i can't use this unsupported device any more and my old iMac is no longer with me in this world.
    Please need help!!

    Great allows only 24 entries.
    I wanna try the DMZ feature but can't seem to find the right place to do it in the Zoom X3. As usual the help stuff is mainly in the installer and that being windows means its not accessible. Ifound this on the Zoom website:
    =============================================
    < Open the Zoom Web Console (<a class="jive-link-external-small" href="http://">http://10.0.0.2), click Advanced Setup, and click the Misc Configuration button.
    If you are using PPPoA encapsulation, from the PPP Half Bridge drop-down menu, select Enable.
    Click the Save Changes button and then the Write Settings to Flash and Reboot button.
    Now you must change encapsulation setting from the default the PPPoE LLCSNAP to PPPoA VCMUX. To do this, click Basic Setup. Then from the Encapsulation drop-down menu, select PPPoA VCMUX.
    Click the Save Changes button and then the Write Settings to Flash and Reboot button.
    Verify that your TCP/IP properties are set for DHCP. You may need to release and renew the IP address. Refer to the instructions in the Zoom ADSL Modem User's Manual (click on Documentation in the main installation menu of the Zoom ADSL CD). Note: The IP address should be the same as the WAN status IP Address, which is located on the System Status page of the Zoom Web Console>
    =============================================
    Okay, my biggest problem is that I'm in Austria with my iMac G5 and my mum is in England with her new iMac G5 intel duo core, so i'm trying to set her Zoom X3 up via telephone with my mum who is 65, yeah so thats the deal!
    So any help would be greatly appreciated.

  • Basic Java Class with prints records out of the DEPT table

    Can some one show a basic java class which will query the DEPT table, and print them out?

    Nagarjuna,
    the Oracle DBMS JDBC Developer's Guide is full of code examples.
    http://download.oracle.com/docs/cd/B19306_01/java.102/b14355/toc.htm
    --olaf                                                                                                                                                                                                                                                                                                                       

  • Would an HP saavy person respond to this issue.. or im going to toss my HP POS out of the window..

    i am trying to find HP recovery cds to BUY .. (one would think that would be easy since well its more money for HP.. )
    for my seagate 1tb barracuda HD that i just found out is a Advanced format HD.. and since my 2009 recovery cds are garbage now i need new recovery cds.. or should i just go spend 100 bucks on a win 7 copy or should i just toss my A6567c HP machine out the window and buy some other brand... im quite livid.. ive searched every spot you can look ive looked up every page one can look .. or am i just unlucky and they dont make new recovery cds for my machine and im stuck with a paper weight now ?
    any direct link by some HP admin would be appreciated.. 
    Things shouldnt be this hard to find online.. 
    starbuxx
    This question was solved.
    View Solution.

    Starbuxx
    You might try the following resource:
    Recovery Kit FL051AV For HP Model Number a6567c
    There is an 800 number you can call with any concerns or questions that you have.
    Click the Kudos Thumbs-Up to show you appreciate the help and time from our Experts.
    Although I strive to reflect HP's best practices, I do not work for HP. 
    Click Accept as Solution when the Answer is a good Fix or Workaround!
    Kind Regards,
    Dragon-Fur

Maybe you are looking for