Output to monitor options

My late 2011 13" MBP only has one TB output which I currently use (TB to hdmi adaptor ) for my samsung hdmi monitor but would like to use the TB out to connect to a TB HD that also only has one TB port. What are my options if any?
Many thanks
Dave

Thanks for your help, I was just referring to
>> Since Thunderbolt displays should always be at the end of a Thunderbolt chain, I'm not surprised that the display you're looking at has only one TB port.<<
It's not a TB Display as I said & understand that if it was why it would only have one TB port, but this point is a little redundant/confusing as it's not relevant to "this" conversation.
I have however looked at TB hubs & the Caldigit TB hub seems like a good option especially at below $200. --> http://eshop.macsales.com/item/CalDigit/TSUS60/
There also seems to be a much cheaper option ($58) USB to hdmi/VGA option both at OWC . This of course ties up a USB port but I might try this first because of price--> http://eshop.macsales.com/item/Newer%20Technology/VIDU2DVIA/
Many thanks again
Dave

Similar Messages

Best Practice for ASA Route Monitoring Options?

We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked options is enabled for monitoring the state of the primary route. the detail parameters regarding options as below,
Frequency: 30 seconds               Data Size: 28 bytes
Threshold: 3000 milliseconds     Tos: 0
Time out: 3000 milliseconds          Number of Packets: 8
------ show run------
sla monitor 1
type echo protocol ipIcmpEcho 10.200.200.2 interface Intersite_Traffic
num-packets 8
timeout 3000
threshold 3000
frequency 30
sla monitor schedule 1 life forever start-time now
------ show run------
I'm not sure if the setting is so sensitive that the secondary static route begins to work right away, even when some small link flappings occur.
What is the best practice to set those parameters up in the production environment. How can we specify the reasonanble monitoring options to fit our needs.
Thank you for any idea.

Hello,
Of course too sensitive might cause failover to happen when some packets get lost, but remember the whole purpose of this is to provide as less downtime to your network as possible,
Now if you tune these parameters what happen is that failover will be triggered on a different time basis.
This is taken from a cisco document ( If you tune the sla process as this states, 3 packets will be sent each 10 seconds, so 3 of them need to fail to SLA to happen) This CISCO configuration example looks good but there are network engineers that would rather to use a lower time-line than that.
sla monitor 123
type echo protocol ipIcmpEcho 10.0.0.1 interface outside
num-packets 3
frequency 10
Regards,
Remember to rate all of the helpful posts ( If you need assistance knowing how to rate a post just let me know )

Why does final cut x not recognize the sharp PN- K321 monitor ( European version ) as output video monitor and premiere it? Working with two cinema display and PN- K321 and I can not preview the output video at 4K for DisplayPort, whereas with premie

Why does final cut x not recognize the sharp PN- K321 monitor ( European version ) as output video monitor, and premiere yes?
Working with two cinema display and PN- K321 and I can not preview the output video at 4K by DisplayPort, whereas with premiere and after effects I have no problems

Look, you can build an HD DVD with an SD movie, just as you can build an SD DVD with an HD movie. This is not a bug, it is most likely user error. Apple will not be addressing it.
Just start over, and ensure you are building an SD DVD by bringing up the inspector for the disc (click on the background in the Graphical tab).
Make sure SD DVD is selected:
(If you do the same thing on your ill fated project, you'll see that HD DVD is selected)
Build your DVD and you'll be fine.
Patrick
P.S. You will need to google HD DVD and Blu-Ray if you want to understand the difference between the formats. The reason that DVDSP included HD DVD was that its format was similar to SD DVD's. Blu-Ray is something else entirely.

View Output/View Log options are redirecting to browser automatically in Oracle Apps 11i

Hi,
Can any one please let me know the what is the option to change popup options in oracle apps 11i.
My requirement is when I click on view Output/View Log options it should pop up there itself rather than redirecting to browser.
Application version is : 11.5.10.2
Thanks,
Govind

Hi,
Clear the value for the following profile option:
Viewer: Text
Regards,
Bashar

External monitor options For Macbook Pro(2011)

Just curious as to what my monitor options are as a external monitor for the Macbook Pro. I'm pretty much set on 27'' thunderbolt display but its a hefty price to swallow...
Best buy has some good deals on there 27'' monitor but can i get the same resolution and clarity from other brands that will be eqivalent to Apple?
I'd like to stay in the 27'' to 30'' size...
thanks

Any other options like Samsung, LG etc... that offer the same specs as the thunderbolt display?
Thanks

PRO Tip Monitoring option was disabled on SCVMM

Hello,
I have integrated SCVMM 2012 R2 and SCOM 2012 R2 also test the PRO ,the jobs ran successfully.
But i could not able option to enable PRO "Monitor option"(it is disabled) on SCVMM.how to enable this.

You must be a member of the Administrator user role to set up and modify the connection to an Operations Manager server
Also check below links
http://blogs.technet.com/b/scvmm/archive/2011/04/14/operations-manager-integration-and-pro-improvements-in-scvmm-2012.aspx
http://blogs.technet.com/b/kevinholman/archive/2012/08/21/integrating-vmm-2012-and-opsmgr-2012.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Thunderbolt to SDI Monitoring Options?

I've been reading here that the current SDI reference monitor setup I've used for Resolve will not work wtih Speedgrade since it uses the Blackmagic Mini Monitor to connect Thunderbolt to the SDI.
I'm interested in moving over to Speedgrade for grading if possible, but I'm using the new MacPro and iMacs -- none of which work with nVidia cards. At this point all Apple Mac solutions will need to be Thunderbolt based.
So what is the simplest and least expensive way to get an SDI signal from a thunderbolt port that is compatible with Speedgrade?
Thanks!

BMD makes 4 different types of TB output devices, Aja makes another 3.
You have to decide what works for you and your workflows since you have not mentioned what type of content you work, so it's impossible to offer suggestions. Option are available for HD and 4K output from both companies.
I work on commercials, features and episodic television, I use the best tools I can get my hands on,
Gary Adcock
Studio37 Inc.
Production and Post Workflow
Camera and OnSet Technology.
Chicago, IL. USA.
This device has a tendency towards horrible spelling, it's actually worse than my spelling naturally is.

Current Monitoring Options?

I'm running a DeckLink card to an HDLink SDI->DisplayPort and onto a DreamColor.
This doesn't work with SG.
I'm looking at what other options i have.
It seems that the simplest might be a Quadro 4000 display port into the DreamColor as a second video card. It should be 10bit and RGB so should work with the DreamEngine colour processing. Does that sound like a plan?
The downside is that my original route is all video, which means that motion is rendered at exact frame rates whereas i'm worried that a card into dreamcolour will mess with the frame redraws (i.e. not be *exactly 50Hz* but over or under slightly.
What is everyone else doing?
thanks!
Paul

I have 2 cards because of Resolve ironically. (Only one outputs video to screens though)
In Premiere I have GUI for PPro application on 1 and full screen monitoring on the 2nd.. plus a BM card (sdi) to a BC Monitor.
IN SG I have GUI for SG application on 1 and full screen monitoring on the 2nd.
Neither of these setups use the 2 cards like Resolve does. ie. 1 for Monitoring...the other for GPU processing.
IN SG I see no way to set up two graphic cards.
Only solution I see is to dump the BM cards (!!!) and use AJA cards..

SX20 main cam output on monitor 1 and monitor 2 at the same time

Hi Community,
we have an SX20 (TC7.0.2) and need to have the main source (12x Cisco cam) on both monitor outputs, because we need to record the VC session.
DD option is installed. Is there a way to get this configured ?
Regards
Jens

If you just want to record what the SX20 sends out to its main monitor to a second screen/recorder, you could just use something like a DA2 to duplicate the audio/video that is played locally.
In addition to what Patrick has said about the video from the local camera though - you're also not going to get the local audio through the monitor output - only the far end - so, again, this may not be what you're wanting if you're looking to record the whole video conference (audio and video from both ends).
I suggest you look in to the Cisco TelePresence Content Server product if you're looking to do recording on a regular basis.
Wayne
Please remember to rate responses and to mark your question as answered if appropriate.

HDMI output to monitor not displaying all colors

I am trying to use a second monitor on my Satellite S55t-b5152 and am able to get 1920x1080 output from the HDMI port through an adapter to either VGA or DVI into my external monitor, but with either adapter the colors look washed-out and not all the colors that are displayed on the internal monitor show up on the external monitor. For example the position indicator in scroll bar on some apps shows up on the internal monitor, but disappears when I drag that window onto the external monitor. I've tried multiple monitors and they all have the same symptom. I've investigated this some on external forums and it seems to be that the HDMI output under some conditions assumes that it is connected to a TV instead of a monitor and it limits the output color range. On some graphics drivers it is possible to override that assumption and get the full range output from the HDMI port. I haven't found a way to do that for the graphics driver on the S55t-b5152. Has anyone figured this out?

Satellite S55T-B5152
through an adapter to either VGA or DVI...
Just want to comment that I'm not at all surprised that an adapter does not produce true colors. I'm sometimes amazed they work at all.
Yours is HDMI 2.0 which complicates things still further.

Output to monitor/projector

Will iOS 4.2 have the ability to output to an external monitor/projector?
I know Apple left it up to the software developers to enter in this code but why can't the iPad just have this ability out of the box? Those that have jail broken their iPad already have this ability in the settings. That just shows that the iPad could do this but apple won't allow it.
Apple why can't we have this functionality? I would love it for myself for various reasons, but I work for a large school and the faculty members that have purchased iPad's want to output to a projector as part of their teaching.
Heck...apple didn't even add this functionality into Safari.

We are all users here. We do not know why Apple does/does not do what it does. If you want to make a suggestion go here:
http://www.apple.com/feedback/ipad.html

V210 won't output to Monitor

Had to replace my old v210 with a new one. The new one did not come with a video card or DVD-ROM, so I took them out of the old server. The DVD-ROM works fine, but I either get no output on the monitor, or if I do, it looks like a sync'ing issue (horizintal multicolored lines). The only difference between the old and new server - besides no video and DVD, is the new server is dual-cpu with 8GB RAM, whereas the old one was single CPU with 4GB RAM.
I cannot locate any information on Oracle's site on how to troubleshoot a video problem. I downloaded all the manuals they have at (http://download.oracle.com/docs/cd/E19088-01/v210.srvr/index.html) but nothing is covered in any of them.
During boot and diags, the monitor does come on as it polls the bus, but it does not stay on, or has horizontal lines. I'm posting the output of my POST and eeprom settings in hopes someone can help.
POST results
Sun Fire[TM] V210/V240,Netra[TM] 210/240 POST 4.30.3.b 2009/07/21 13:27
/export/delivery/delivery/4.30/4.30.3.b/post4.30.3-micro/Fiesta/enxs/inte
grated (root)
0>Copyright 2009 Sun Microsystems, Inc. All rights reserved
0>OBP->POST Call with %o0=00000800.01012000.
0>Diag level set to MIN.
0>Verbosity level set to NORMAL.
0>Start Selftest.....
0>CPUs present in system: 0 1
0>Test CPU(s)....|
0>Interrupt Crosscall....Done
0>Init Memory....Done
0>PLL Reset....Done
0>Init Memory....Done
0>Test Memory....Done
0>IO-Bridge Tests....Done
0>INFO:
0> POST Passed all devices.
0>
0>POST: Return to OBP.
Configuring system memory & CPU(s)
Probing system devices
Probing memory
Probing I/O buses
pci0 not found.
Probing system devices
Probing memory
Probing I/O buses
Sun Fire V210, Keyboard Present
Copyright 2009 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.30.3.b, 8192 MB memory installed, Serial #66908789.
Ethernet address 0:3:ba:fc:f2:75, Host ID: 83fcf275.
Running diagnostic script obdiag/normal
Testing /pci@1e,600000/ide@d
Testing /pci@1e,600000/isa@7/rtc@0,70
Testing /pci@1c,600000/scsi@2
Testing /pci@1c,600000/scsi@2,1
Testing /pci@1e,600000/isa@7/serial@0,2e8
Testing /pci@1e,600000/isa@7/serial@0,3f8
Probing system devices
Probing memory
Probing I/O buses
pci0 not found.
Probing system devices
Probing memory
Probing I/O buses
Sun Fire V210, Keyboard Present
Copyright 2009 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.30.3.b, 8192 MB memory installed, Serial #66908789.
Ethernet address 0:3:ba:fc:f2:75, Host ID: 83fcf275.
Rebooting with command: boot
Boot device: /pci@1c,600000/scsi@2/disk@0,0 File and args:
SunOS Release 5.10 Version Generic_118833-33 64-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Hardware watchdog enabled
Hostname: NCC
checking ufs filesystems
/dev/rdsk/c1t0d0s7: is logging.
================================================
EEPROM
# eeprom
asr-policy=normal
keyboard-layout: data not available.
test-args: data not available.
diag-passes=1
local-mac-address?=true
fcode-debug?=false
scsi-initiator-id=7
oem-logo: data not available.
oem-logo?=false
oem-banner: data not available.
oem-banner?=false
ansi-terminal?=true
screen-#columns=80
screen-#rows=34
ttyb-rts-dtr-off=false
ttyb-ignore-cd=true
ttya-rts-dtr-off=false
ttya-ignore-cd=true
ttyb-mode=9600,8,n,1,-
ttya-mode=9600,8,n,1,-
output-device=ttya
input-device=ttya
auto-boot-on-error?=false
error-reset-recovery=sync
load-base=16384
auto-boot?=true
network-boot-arguments: data not available.
boot-command=boot
diag-file: data not available.
diag-device=net
boot-file: data not available.
boot-device=/pci@1c,600000/scsi@2/disk@0,0
use-nvramrc?=false
nvramrc: data not available.
security-mode=none
security-password: data not available.
security-#badlogins=0
verbosity=normal
diag-trigger=error-reset power-on-reset
service-mode?=false
diag-script=normal
diag-level=min
diag-switch?=false
#

Why would you expect a monitor to show anything, when the new system is using its factory default configuration?
output-device=ttya
input-device=ttyaBy the way, that is the preferred method to administer those 1U systems.
Connect another system to the serial console port and set that system up as you want.
Did you even take the opportunity to tell the OS of the existence of that card? There isn't any Plug-n-Play as your personal Microsoft PC might have. You likely will need to do a reconfiguration reboot, then install drivers for the video card then more reboots. Have a Sun USB keyboard/mouse kit connected as well, else you may still never see any monitor output.
Go get the V210 documentation and use its guidance to set the system as you want it.
http://download.oracle.com/docs/cd/E19088-01/v210.srvr/index.html

PO Output type with Option 5 External Send (&EKKO-EBELN&)

Dear Friends,
We have come across and interesting issue.
We want PO output to be send to vendor via email and the email subject should be "New Purchase Order <po document no>". To achieve this requirement we have set the Output type NEU --> Mail title and Text as NEW PURCHASE ORDER &EKKO-EBELN&.
When PO is created and before saving the PO user select the option 5 External Send in Message and further go to the communication tab. he can see the 'NEW PURCHASE ORDER &EKKO-EBELN&.' in Cover Page Text.
But the movement user saves the PO, Message --> communication is replaced with 'NEW PURCHASE ORDER".
And finally when the mail is sent with no PO document number and subject as "NEW PURCHASE ORDER".
Has any one has come across this issue before?
Or is there any OSS note for this?
Please Help!!
Sandeep

dear sandeep
you can follow below mention steps or reffer OSS
1. You must maintain an e-mail address in the address in the vendor master.
2. The same applies to your own user master. You also have to specify an e-mail address there in order to identify the sender.
Note that it is not possible to change the e-mail address of the vendor via the SAP purchase order transaction (ME21N, ME22N, and so on). The system only uses the e-mail address of the vendor that is maintained in the vendor master!
3. For the output type for default values, a communication strategy needs to be maintained in the Customizing that supports the e-mail. You can find the definition of the communication strategy in the Customizing via the following path: (SPRO -> IMG -> SAP Web Application Server -> Basic Services -> Message Control -> Define Communication Strategy). As a default, communication strategy CS01 is delivered. This already contains the necessary entry for the external communication. Bear in mind that without a suitable communication strategy it is not possible to communicate with a partner via Medium 5 (external sending).
4. Use the standard SAP environment (program 'SAPFM06P', FORM routine 'ENTRY_NEU' and form 'MEDRUCK') as the processing routines.
5. In the condition records for the output type (for example, Transaction MN04), use medium '5' (External send).
6. You can use Transaction SCOT to trigger the output manually. The prerequisite for a correct sending is that the node is set correctly. This is not described here, but it must have already been carried out.
7. To be able to display, for example, the e-mail in Outlook, enter PDF as the format in the node.
For more details, check out the OSS note :191470
Hope this will help.
reward points if helpful
thanks and regards
ravikant dewangan

'Setup System Monitoring' option is disabled in solution manager

Hello,
I am trying to setup system monitoring for different systems in solution manager but the 'Setup System Monitoring' is disabled.
In solman I go to Solution_manager --> Operations Setup --> on the right side pane 'Setup System Monitoring' is disabled. How can you change this to change mode so that you can configure monitoring for different systems? Any idea, please help.
Thank you in advance.
Sameer
Edited by: Sameer Pant on Mar 19, 2011 1:07 AM

Hi Lakshmi,
But when i right click on the qualifier
No u hv to right click on a field to which Compound field is mapped ( Ur Main Table Field)
Right Click on Compound field & choose option Set Qualified Update.
New Links: Create
Existing Links: Update (All Mapped Qualifiers)
Thanks,
Maheshwari

External Monitor Options for iMac?

I have an iMac and have been using a lot with my 7D files. They look great, but I would like to have an external monitor output. Any ideas on output modules for iMac? Thanks!

is if there is a Firewire out that can send my Color display out to my Trinitron monitor, like FCP
No, absolutely not. COLOR does not support FireWire output. The developer intended the application to be used with a PCIe Video I/O interface, (Kona, for example, as opposed to GPU) supporting HD-SDI output, and the fixed output gamma characteristic of 2.2 was assigned as default to support that.
*All other approaches* are considered to be +ad hoc+ substitutes and are +de facto+ "as is". The policy should be read as -- "we made it one way which functions very precisely; if you want something else, that's your business"... but for a very large number of non-broadcast content producers, that's fine. It doesn't matter if its technically "wrong", as long as there is a result, not to imply that no one cares about the products they are generating -- but there are obviously some very large knowledge gaps in the consuming population in this area.
That's my possibly cynical interpretation of the history and situation...
jPo

Output to monitor options

Similar Messages

Maybe you are looking for