Outputs Suddenly Stopped Working.

I have a 5th gen Ipod that I've taken very good care of. Until yesterday I've had no problems with it at all. I was using the Ipod in my car w/ my Itrip and the Audio suddenly stopped working. I assumed it was the Itrip not working correctly, so I plugged it into a set of speakers (via the bottom output) but that wasn't working either. Then I plugged headphones in and there is no audio feeding through the headphone output either. I can see on the screen that the songs are playing on the ipod, but apparently the outputs are not functioning correctly. I tried all of the "Rs" recommended in troubleshooting but those did not help. Any suggestions?

i have the exact same problem. Although i am able to here the clicks throught the headphones which makes me wonder that this is something with software. although i have restored and reinstalled and all that, nothing.
Anyone have a solution?

Similar Messages

Drive suddenly stopped working

Hi there, can anyone help/advice on this issue. My Lacie external firewire drive suddenly stopped working, the green light on the power pack had died so i replaced the powerpack thinking this was the problem. Still nothing. Te HD does not show up on the desktop or disk utility. The drive does not seem to power up audibly like before, although the blue light comes on. I have tried it on several other newer more powerful macs in the office and still no joy. Ideas? thanks

hi there, thanks for getting back in touch. Yes I guess it could have just died The power brick is rated the same yes, same input power and output, also tested on another brick which belongs to another drive exactly the same. I dont think there is any warranty, it is about 5years old. Not tried the USB, I will give it a try though. Not sure what the drive configuation is inside the case, but may try and remove them and put them in another case, see if I can get any data off. Thanks

Dbx for Forte Developer 6 on SunOS 5.10 suddenly stopped working

I know this is the forum for Sun Studio but it was the closest I could find to answer the question. If there is one for Forte Developer, please point me to that.
The problem I have is that last week dbx suddenly stopped working for me. I would try to lauch it and it would just hang and be unable to be killed with kill -9.
I've asked my sys admins to look into the issue but haven't gotten a response yet so I thought I'd try here.
I have some truss output but I can't post it here because of length issues. If somebody wants it, I can send it to them.
Thanks,
Madison

Forte Developer 6 is part of the Sun Studio family, so you have found the right forum. :-)
FD6 is End Of Service Life, and no support has been available for it since 2006.
In addition, it is not supported for use on Solaris 10. If it was working previously, it was only by accident.
You should get Sun Studio 12, the current release, or wait a few weeks and get Sun Studio 12 udpate 1. It is free for all uses, does not use a runtime license (only a license agreement), supports modern hardware and operating systems, compiles faster, produces code that runs faster, has much better support for C++ (and supports C99), has a greatly improved debugger and has other new development tools.
You can get the current Sun Studio here:
[http://developers.sun.com/sunstudio/]
... and the current patches for it here:
[http://developers.sun.com/sunstudio/downloads/patches/index.jsp]
The Support Matrix shows what OS versions are supported by the various Sun Studio releases, and the lifetime of each.
[http://developers.sun.com/sunstudio/support/matrix/index.jsp]

Bluetooth on imac suddenly stopped working

To start, thank you for reading this question with the intent to help. My imac LionOSX 10.7.5 . Does anyone have experience or knowledge about how the bluetooth to a computer can suddenly stop working. It happened at the same time that the computer start up slowed way down (Just took 4 minutes...i timed it so I could know for sure). It used to start up in about 30 seconds or less. (The computer itself seems to work as fast as normal once the start process has finished.
At first, I thought there was something wrong with my keyboard and mouse, but couldn't even log in to access the system preferences, as both were not working. So I grabbed an old keyboard and mouse from my Windows desktop, plugged them in and was able to log in. That is when I noticed that the bluetooth icon in the menu at the top right of the screen showed a line through the bluetooth icon and when I click on it, it says "bluetooth unavailable. When I click on the "About this Mac"/more info and look under bluetooth, it says "no information found". Also, the mouse I plugged in stopped working the next day until i plugged it into a different USB port.
My fear is that I accidentally downloaded some kind of malware that is eating up different functionalities on my computer. I did use a web-service to download a youtube video on neck exercises (how stupid of me...could have simply bookmarked it and pulled it up just as easily)
If you can help, I would be oh, so grateful. I know my way around computers in the most basic sense, but don't understand much about the how's, why's, how-to's of computer technology.
Thanks. Your friend, Patti P

Sorry I haven't gotten back with those of you sooner about your suggestions and how they have been working. Tried one day, but the site was down due to maintenance.
I have been trying all the wonderful suggestions people have given, but so far with no luck. It is absolutely clear that the problem is with the internal bluetooth and not with the keyboard or mouse. I bought an external bluetooth usb adaptor, and now my bluetooth devices are usable again, but the internal bluetooth is still unavailable. Thanks for letting me know that the long wait at startup was more than likely due to the system searching for the bluetooth, very comforting.
In one article I read, the person recommended trashing the plist file, com.apple.bluetooth.plist, but I couldn't find a file like this in the library. However, I did find a file named 'com.apple.Bluetooth.Audio.plist' which was modified on June 12, which is the same time the bluetooth stopped working. I don't know what to do with this file, since I really know nothing about how computers work, code, etc., etc. I just really enjoy the finished product, so to speak. But here is what I found when I opened the plist file.
Here is the first entry:
Root: previous input UID Dictionary: string Value: AppleHDAEngingInput:18,0,1,0:1
When I clicked on and opted to copy, this is what pasted when I pasted it: <?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<string>AppleHDAEngineInput:1B,0,1,0:1</string>
</plist>
There is a 2nd entry:
Key/Root: previous output UID Type/Dictionary: string Value: AppleHDAEngineOutput: 18,0,1,2:0
When I copied and pasted this string (or whatever it is called…it's all greek (or perhaps I should say geek) to me, here's what pasted:
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<string>AppleHDAEngineOutput:1B,0,1,2:0</string>
</plist>
I also found two files that were logs of events that occurred on the 12th and 13th. I have copied and pasted this info and put it into two text docs, which if I can figure out how, I will attach in case someone is able to look at code and figure out what it means. That is way beyond me (and I envy those who can read this foreign language)
In addition, there is a folder named 'com.apple.BluetoothFileExchange.savedState' which was created on June 12th also. It has 2 documents, one named 'data.data' and another named 'windows.plist' I took a screenshot of the plist file which i hope I can include somehow in this post.
There is a 2nd folder created June 23 named com.apple.BluetoothSetupAssistant.savedState that has a data.data file and another windows.plist
These are the only files/folders that came up when searching the library under the key word bluetooth.
Thanks to everyone who was so willing to help. While I wasn't able to fix the problem, I learned lots of good stuff, like how to find my library, etc. so just know your efforts to help were not in vain.
Your (grateful) friend, Patti P

Optical audio output has stopped working - can anyone help?

My optical audio output has suddenly stopped working. I use the Mac Mini as a music centre, so use the optical out all the time. The analogue signal works (when I plug in headphones, I can hear the music) AND I have checked my audio system by plugging another Mac mini into it and it worked.
I can see the red laser light from the cable when I unplug it.
I have not changed any settings.
I presume this is a hardware failure - but it seems like a strange one as the analogue audio is working.
Any ideas?

try some of the usual troubleshooting steps:
_*resetting your Mac's PRAM and NVRAM*_
_*resetting the System Management Controller SMC*_
also, run _*Apple Hardware Test*_, using the installation DVD that came with the mini, to see if any hardware problems are reported.
JGG

Photoshop CS4 64bit suddenly stop working

Having problems with Photoshop CS4 64bit version stop running for me giving me this error message with these details:
Problem signature:
Problem Event Name:    APPCRASH
Application Name:    Photoshop.exe
Application Version:    11.0.1.0
Application Timestamp:    499bfd16
Fault Module Name:    StackHash_0b5f
Fault Module Version:    6.1.7600.16385
Fault Module Timestamp:    4a5be02b
Exception Code:    c0000374
Exception Offset:    00000000000c6cd2
OS Version:    6.1.7600.2.0.0.256.1
Locale ID:    4105
Additional Information 1:    0b5f
Additional Information 2:    0b5f2ed00a0371f4956b3b2a23be79e0
Additional Information 3:    a274
Additional Information 4:    a2747fd43e73092b139f32555a88633d
It seems when i do something simple as typing text, it'll stop working and give me a "Adobe Photoshop suddenly stop working". My CS4 32bit version seems to working fine with whatever i'm working on. I'm running a fresh install of Windows 7 64bit Ultimate on a new computer Intel quad core with 4gig of ram if that helps. Sorry if this have been asked before but i couldn't find anything on these forums. Thanks in advance.

i deleted the prefs file and now i can open photoshop. but it seems as if it crashes if i open ANY file with ANY text, no matter what the font is.

My usb that i have been using on my computer for a while suddenly stopped working, but is still glowing and letting me know that it is connected, but not showing up in disk utility

my usb that i have been using on my computer for a while suddenly stopped working, but is still glowing and letting me know that it is connected, but not showing up in disk utility

Either the physical drive or the enclosure electronics has failed. The light you are seeing is powered by the USB connection, the power, electricity, all USB ports put out. That doesn't mean the actual physical hard drive or the USB to SATA bus electronics are working properly. If it doesn't show in Disk Utility then it is DEAD.
Most of the time it is the enclosures electronics that fail. Removing the physical drive from the enclosure and put it in another enclosure or using a SATA to USB adapter, one that has it's own AC power supply, might allow you to get the files off the drive.

Satellite L300 suddenly stopped working - new motherboard needed

My Sat L300 suddenly stopped working the other day.
It kept freezing to start with, then nothing at all. So, I kill-disked the HDD and tried to re-install Windows (XP).
During the install it threw up a message that some internal components had been incorrectly installed and needed to be reinstalled.
I was told to remove the memory cards and re-seat them.
That did not work. I thought that perhaps the HDD was damaged, so I fitted a new one, and started to reinstall Windows.
Once again, same message. One of my colleagues at work suggested that the Motherboard was probably U/S.
So I have been trawling the .net to find a replacement. Laptop out of warranty! I am told that some other serial numbered motherboards will work with this laptop. Don't really want to get a motherboard only to find its never going to work! My unit has an SPS number of: V000138330.
I am being offered one with an SPS of: V000138390.
Any ideas? Will this one work?
And if it does, will it give me the functionality that I used to enjoy?!
Sorry for the long sob story.
Any advice gratefully accepted.
ANDY-N

Hello Andy
Sorry but can you tell us more about your notebook? which model do you have exactly (L300-xxx)?
Do you have European model?
Has your notebook valid warranty?
Maybe I have misunderstood something but why you want to exchange mainboard if the warranty is probably still valid?

My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?, My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?

My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?, My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do? iPhone 5

Clean the lint/debris from the charging port and plug the cable in.

Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!! SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.

The issue: Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!!
SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.
The cause: It is now clear what caused this problem. For years I had several “all-day” events in my Outlook calendar (birthdays, anniversaries, etc.). In May 2012 I decided to make some of them one hour events so I could add alerts to remind me of the event. I did this by dragging them in Outlook to the time I wanted and expanding them to the time slot desired and then adding the alarm.
The symptom: Syncing stopped working for the calendar but continued working for contacts and notes. I didn’t realize sync was failing until months later when I missed two very important phone calls, so when I noticed it the cause was not obvious.
The failed attempts: I’m head of a software firm and my calendar sync is a crucial to my business life so I took this on with a vengeance. From a quick look at events in Outlook and the iPhone I could see that the problem started in May 2012. Events before May were in both Outlook and the iPhone but events after May were only one or the other. Unfortunately I had changed several other things at the same time relating to other events so again the cause was not obvious. MANY calls with AppleCare proved them incompetent so my internal IT guys assisted trying many things. We tried a huge number of calendar changes and several versions of iTunes, iPhone OS and Office as well as both iPhone 4 and 5, all without success.
The fix: After 18 months of frustration, MANY hundreds of $ expense and MANY hours of wasted time I saw a blog that had a calendar sync problem and it indicated all day events were related. I changed the display of the Outlook calendar to the list view, added columns so I could see “all day” event check marks as well as times of events, sorted on the “all day” event column to move them to the top, and for all events that were “all day” events AND had a start and end time, I removed recurrence and then added the annual recurrence back…
After I fixed all events that had BOTH “all day” set and had a start/end time, I tried another sync. It synced for the first time in 18 months!
Problem occurred May 2012 – fixed Nov 2013

Hi, to remove dummy '_ModGrp' entries, rather than crashing the 'Suppr' key on your keyboard, you can use this basic VBA macro (launched for instance from Excel).
It will recursively remove all '_ModGrp...' folders
Sub RemoveFolders_Click()
    Dim oOutlook As Outlook.Application
    Set oOutlook = New Outlook.Application
    Set objNameSpace = oOutlook.GetNamespace("MAPI")
    Call CleanFolders(objNameSpace.Folders)
End Sub
Sub CleanFolders(objFolders As Outlook.Folders)
    For i = objFolders.Count To 1 Step -1
        If Left(objFolders(i).Name, 7) = "_ModGrp" Then
            objFolders.Remove( i )
        Else
            If Not objFolders(i).Folders Is Nothing Then
                Call CleanFolders(objFolders(i).Folders)
            End If
        End If
    Next i
End Sub

HT201263 My iPod touch suddenly stopped working. It was fine, but when I went back the screen had gone black and I was unable to turn it on. It is now unresponsive and my computer does not recognize it when it is plugged in. What should I do?

My iPod touch suddenly stopped working. It was fine earlier, but when I went back a few hours later, the screen had gone black and I was unable to turn it on. It is now unresponsive and my computer does not recognize it when it is plugged in. I thought it just needed to be charged but there seems to be a larger issue now. What should I do?

Let your ipod die. Then when it is dead charge it adn turn it back on. After that it should be fine.

HP Pavilion dm1-4000au Entertainment Notebook PC_Keyboard and Touchpad Suddenly Stops Working

Hi there,
I have an HP Pavilion dm1-4000au Entertainment Notebook PC (QG411PA) running Windows 7 Ultimate 32-bit for more than a couple of years already. During those times up until now, whenever my laptop is on standby for an hour or so, its keyboard and touchpad suddenly stops working, regardless if its running on battery or on AC power.
I always ensure that I have an external mouse in order for me to navigate properly and pull up the on-screen keyboard in order to type once that issue arises.
All appears to be updated in terms of Windows Updates and I even reformatted it, but issue still persists.
Is this particular issue that I am experiencing a harware issue? Perhaps a software issue? Or maybe a defective model itself?
Your prompt response is highly appreciated.
Sincerely,
Led
This question was solved.
View Solution.

Dear Customer,
Welcome and Thank you for posting your query on HP Support Forum
It looks like you are facing difficulties to resolve Touchpad Issues with your Notebook
We will surely assist you with this
Steps to drain the Static charge and loading default BIOS settings to resolve the issue
Step 01. Turn OFF the Notebook
Step 02. Un-plug the Power/AC Adapter and also remove the Battery too
Step 03. Press and Hold the Power Button of the Notebook for a full minute
Step 04. Now let's re-insert the battery back in and plug back the Power/AC Adapter
Step 05. Start the Notebook and keep tapping F10 Key during the startup to access the BIOS
Step 06. Once you get to the BIOS, Please press F5 or F9 Key to load setup defaults for the BIOS
Step 07. Now let's press Esc/Escape Key. Save Changes and Exit - Yes
Step 08. Now please wait till the Unit loads the Windows Operating system
Now please download and re-install the touchpad drivers for your Notebook from the HP Support Site
Please Click this Link to find more troubleshooting steps to resolve this issue
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

My iTunes suddenly stopped working and doesn't recognize any of my devices and gives me a AMD error. I've tried several times to uninstall all Apple programs and reinstall to no avail. I'm running windows 7 on a Dell laptop. It worked fine for years .

My iTunes suddenly stopped working and doesn't recognize any of my devices and gives me a AMD error. I've tried several times to uninstall all Apple programs and reinstall to no avail. I'm running windows 7 on a Dell laptop. It worked fine for years then I decided to update my iPhone 4S and it didn't recognize it or any other iPod or iPad.
Can someone please help ?

I am having all sorts of problems with 9.1.1.Crashes and not only iTunes but I have to restart all the time.
GET TO WORK APPLE !!!!

Ethernet suddenly stopped working for no apparent reason

My late 2011 MBP is usually functioning as a desktop with external display and keyboard/trackpad, so I have it connected via ethernet when it's on the desk. However, my connection suddenly stopped working for no apparent reason.......... BUT clearly not a router problem as there's no problem with the wifi connection. System Preferences > Network > Ethernet is telling me:
Status: Connected. Ethernet has a self-assigned IP address and will not be able to connect to the internet.
Dunno how this happened, as to my knowledge I didn't actually do anything to cause this problem, just randomly stopped working. Any solutions much appreciated, thanks :-)

Please post a screenshot of the Network preference pane. Be careful not to include any private information.
Start a reply to this message. Click the camera icon in the toolbar of the editing window and select the image file to upload it. You can also include text in the reply.

Satellite L300 - Built In webcam suddenly stopped working

Hello,
I have a Toshiba Satellite L300 with a built in 2.0 USB camera and a windows 7 operating system, the camera suddenly stopped working since about 2-3 weeks ago with unknown reason!
I already tried system restore, un-installing and re-installing the camera driver, preformed a full scan by kaspersky internet antivirus 2012 (up to date), and I also ran a complete system and drivers troubleshooting ... and the problem still exists ...
When I use the windows live movie maker it gives me an error saying: cant record audio or video from the selected device. Make sure that the device you're trying to use is installed properly and not currently in use by another program.
The microphone works well on skype but the camera doesn't open!
Please tell me how to fix it, what am I missing?

> webcam appears in the device manager
Is it marked with an yellow exclamation mark?
Usually if the webcam software has been installed, you should be able to start this software going to:
All Programs -> Toshiba
There you should find the webcam software check if you can use and control the webcam after this software has been started normally the webcam control bar should pop up if you would move the mouse cursor above the upper display area PS: the bar can be moved to other area too; left right or bottom

Outputs Suddenly Stopped Working.

Similar Messages

Maybe you are looking for