Overclocking my 3200+ Winchester on K8N Neo2.. Help!!!

Ok ive had my system for over a year now and i wanted to try my hand at some overclocking and so far ive come up with these settings (check sig for details on system)
235mhz HTT Frequency (Front Side Bus)
10x Cpu Multiplier
Vcore 1.55v (with CPU Vidd at 5% increase incase it needs some more juice)
166 Memory @ DDR 333 speeds now
2-3-2-5 1T Timing
Memory Voltage at 2.65
4X HT Multiplier
So far its been running nice and stable at 2.35GHz with no problems what so ever. Im also running two Sata Drives on ports 1 & 2, should i switch those back to 3 & 4? but when i had them on 3 & 4 my system sometimes would not detect my 160GB drive on port 4 but it would always see my 80GB Raptor on port 3, what is up with that? I know my drives are fine cause before i got my Raptor i had the 160GB on port 3 with no problems for a whole year, its just when i started to use port 4.
Besides that, what suggestions do you guys have that i should try to see if i can get my system to atleast be up at 2.5GHz? Now ive done a search on previous threads and yes ive looked at the sticky's and even overclocking guides, but i wanna hear suggestions straight from people who have the exact same setup as me...

Ok, after i got home from work i switched my SATA drives to ports 3 and 4 and miraculously i am no overclocked to 2.5ghz!! BUT i have a problem...
Ok to start off, after i got my raptor drive i had my two drives plugged into ports 3 and 4 but sometimes it wouldn't detect my new raptor drive on port 4.. so i switched to ports 1 and 2 with the same cables and all was well. Now, since there back on ports 3 and 4 im overclocked, and when i was stressing my system at 2.5ghz, around 2 hours through prime 95 it shutdown and rebooted from a sever error!! now either thats because my system lost my raptor drive on port 4 or cause the overclock is too high and maybe not enough voltage on my ram..
So right now i have my ram bumped up to 2.7 volts and so far no problem after running prime for 45 min on the new voltages.. i had to stop it though but like i said, so far it was fine..
Now, what are the chances of my system suddenly dropping and losing my raptor drive on port 4 while windows is running? could that have caused my system to screw up and restart running prime after 2 hours? or do you think it was my ram voltages? The only way i can tell if my system is definately not picking up my drive some of the times is when i would sometimes turn my comp on it wouldn't see my drive or after a restart it wouldn't see my drive (that was back when i first got it), and so far it hasn't done that yet.. Oh yeah, way back when i first got the two drives i only had a 420W PSU, recently i bought a 550W with 19amps on the 12 volt rail so maybe that fixed the problem??

Similar Messages

New to OC - a64 3200+ 939, MSI K8N Neo2 Platinum

Dear All,
First off. I am new here so hi to you all
I am new to overclocking. Please tell me how far I can go for my CPU (RAM I don't plan to), and what settings in bios I need to change (in simple words, don't try me on abbrev too much :P)
Spec:
AMD Athlon 64 3200+ 939 Winchester
MSI K8N Neo2 Platinum
2x512 Samsung PC3200 DDR Dual Channel RAM (I don't plan to OC RAM)
Antec TruePower 380W (Sonata edition)
BFG GeForce 6800 OC (I don't really plan to OC that either, dunno how)
Would I be able to up from 2.0ghz to 2.2ghz?
Current CPU idle temp: 38 degrees (Arctic Silver 5 applied)
Thank you!
dL

Quote
Originally posted by dL.
Temp at load (playing CS:S) is about 41-42 degrees.
Idle is about 35-38. Temps look ok
Will my Antec TruePower 380W power supply provide sufficient power when increasing vcore? Sjould do just fine Will increasing vcore damage anything? Not as long as it stays cool. How much should I increase it by? Just up a .05 at a time and test.
Also, can I lower my HT to even lower like 3x to get more clock speed? Yes but X4 should be good up to 250. Youn need to keep it under 1000. 250 x4 = 1000
dL

Blank Screen for K8N Neo2, HELP!!!

Ok, my computer used to be working, with windows XP Pro installed, but now it just won't boot up the monitor. The last time I reinstalled the computer, it still wouldn't boot the screen, or would freeze at the platinum screen. I don't think it is the amps. On the DLED, it starts booting up on its own, without hte monitor. The monitor isn't bad, and I know the keyboard works perfectly fine with it (PS/2). I left my DVD writer out, and just stuck my Maxtor 80 GB in primary master. Beforehand, I used the raptor, but it doesn't boot up either... Help...

I've tried the regular bare setup (everything on mobo with nothing else), no effect.

MSI K8N Neo2 Help!!!!!

My system is running perfectly fine but some how the core cell utility keep beeping. Im not sure what is happending. Anyone have similiar problem?
Here is the screenshot of my core cell reading.here

Well we now know the motherboard... what about the rest of the components in the computer. When including specs on the powersupplies (post both the 400w and the 480w) include max amps for the 3.3v 5v and 12v rails. This info can be found on a sticker on the side of the PSU.
Do you have the D-Bracket installed? If so where is it hanging at?
Good Luck
Jeremy

K8n neo2 palt. with cas 2 = no winxp boot

Hi, im havin some troubles with this mobo.
The mobo works fine for timmings configuration like: 2-5-2-2 or 2-10-5-5 or else. But if i try with 2,5-x-x-x or 3-x-x-x windows doesn´t boot, even at defalut HTT. My bios version is 1.B, but i tested with 1.5, 1.36, 1.8, 1.A.... also i tested with two models of memory geil ultra X (TCCD) and ocz platinum EL Pc4800 LTd edition.
My pc:
-Athlon 64 3200+ winchester
-Msi k8n neo2 platinum
-Termaltake pure power 480W butterfly / levicom 420W
-Asus V9999GT/TD
-Seagate 7200.7 120GB ATA
Thanks for your help!

Eltonio,
With Athlon64s the Memory Controller is handled by the CPU, it could be that is all what your CPU is happy with. Is it you are wanting to loosen the timings in order to overclock?
One other option for you is to clear the CMOS by pulling the Power Cord from the Power Supply and the Battery from the Mobo, leaving them out a good 15 to 20 minutes before putting them back in.
Take Care,
Richard

K8N Neo2 hang at decompressing BIOS image to ram. HELP!

Hi,
After several days of flawless running, my computer just died today.
My computer hang at "decompressing BIOS image to RAM for fast booting" (indicated by the D-bracket LEDs) during the startup. I have tried the following but nothing helped.
1) clear CMOS jumper by shorting pin 2 and 3
2) clear CMOS by removing the battery
3) remove the CPU and put it back in
4) take the memory out and put it back in dual/single channel mode.
After pushing the power button, I observe through the LEDs that the mb doing the following
1) System power on
2) Memory Detection Test
3) Decompressing BIOS image to RAM for fast booting and stuck!
Any suggestions is welcome!!
My computer config:
AMD64 3200+ 90nm
MSI K8N Neo2
Bios V1.4
Mushkin basic 512MBx2 (2.5-3-3)
VisionTek Xtasy 9600XT 256MB
Seagate 200GB PATA
Antec Sonata case with 380W power supply

I'd try horspowr1001
with a single module in slot 1
then just for fun
How to clear the CMOS
1) disconnect the power cable.
2) push the power button to drain the capacitors
3) Move the CMOS jumper to the clear position, from it's original 1-2 position to 2-3
4) Wait a minute to be sure the CMOS has been cleared. Take your Time
5) Return the CMOS jumper to it's original position 1-2
6) Plug in power cable.
7)restart computer
8) enter bios and select load optimized Bios defaults - save & exit (hopefully)
9) let pc reboot, Enter Bios Change Ht 5--->4
luck

K8N Neo2 P: Random no boot!!

I need help
I have just built a PC for a customer and am having a few problems with it. The problem is a bit odd in that i can turn it on and it will boot fine and run into windows. Everything appears to be fine. But then maybe a restart or 2 later, or after shutdown then turned back on, the computer will hang at the spash screen. The Hard Drive appears to still be working at this point but nothing happens. There are no beeps or anything. If i leave it overnight or something the computer works.
I thought initially it may be something to do with the ram. It is crucial ram that is installed, not sure if it fully compatible but it works on my home PC and on the customers (when it does boot).
I have also just installed broadband which uses a ZOOM USB modem to connect. I have noticed that the modem sometimes doesn't sync with the ADSL line and then states that the hardware is malfunctioning or the drivers are corrupt. After a reinstallation the modem works for a while, then does the same. Is this linked in any way to the hang at boot.
Any help would be greatly appreciated!
Specs:
Athlon 64 3200+ S939
MSI K8N Neo2 Platinum
Geforce 5900XT - (ex-demo)*
Crucial CT6464Z40B 512mb DDR 400
Maxtor 6Y120M0 120GB Serial ATA
Win XP HOME
ZOOM USB ADSL Modem
56k modem (in reserve)*
Other Peripherals
* - could it be these that might be causing the problem.

Cheers for your help guys. I managed to get it running this morning. Took out the ram and replaced it with some of my Corsair stuff n it worked fine, so there's me thinking i got the problem solved. I then try sticking the customers ram back, of which i thought was faulty, low and behold it worked. So faulty ram it wasn't.
I have no idea what the problem was, maybe the ram wasn't seated correctly or something. Anyways, the computer works now, but i have noticed that when i turn it off at the socket n then back on, there is no power to the usb ports. if i turn the computer off but leave it on at the power i don't have this problem. Tried uninstalling the usb ports n letting windows reinstall them, but didn't work.
Anyway, at least it works now even though i aint sure what the problem was.
Cheers guys

MSI K8N Neo2 Platinum slows down

Hi,
I have a little problem with my new K8N Neo2 Platinum. I installed Windows XP and the newest nForce drivers but if I copy files over LAN (tested both LAN-Ports) or install big applications my music played with winamp slows down. It's played with half speed. In addition to that my mouse pointer is very slow. After the setup or copying files everything is how it should be again. How can I solve this problem?
My system:
AMD Athlon64 3500+ (Winchester)
MSI K8N Neo2 Platinum-54G (tried different bios releases)
1024MB Corsair XMS Twinx DDR500
ATi Radeon 9800 Pro
2 80GB Maxtor S-ATA (DMA Mode enabled)
Creative Labs SoundBlaster Live! Player 5.1
MorLipf

Hello,
I copy files to my bro sometimes, 5Gb - all the steam GCF files for CS/HL/CSS/HL2.
My network usage is 80%-92%
My CPU usage is always under 15%.
It is worse when using 512Mb but as you have 1Gb it shouldn't be bad.
Check in the device manager, your cd drives should be set to DMA mode.

New K8N NEO2 PLAT. and SC-939 3200+ help needed...

Hello,
I have just upgraded my system with K8N Neo2 Plat. and sc-939 3200+ A64 Cpu.
There are several issues I need to resolve which are:
1- Although I change from BIOS the settings for AGP to 4x8x and enable fast writes, I still cant see them turned on from the Catalyst Control Center. Everything is greyed out what can I do? They all used to be on and agp was 8x with my K7N2 Delta board....
2- Although I installed the original drivers from the MSI CD, I couldn't get one of the network prts to install. Realtek installed OK. But other one is defined by the device manager as standart network adapter. What can I do?
3- I am brand new to A64 system so I do not know what setting to use from BIOS can you help me out, for instance there are values for HT such as x3 x4 x5 mine is set to x5? what is this? should I enable cool and quiet, I am not intended to do overclocking. Can you give me some tips for best performance?
My best regards.

Make sure your bios is up to date: version 1.5. Look at the sticky threads and use the information to enable hidden bios features. Disable ATI/NV speedup in the bios. Uninstall your drivers and reinstall. If the information is still greyed out, download the free version of Sandra here: http://downloads.guru3d.com/ and check the module under video system information. This will tell you if fast writes are enabled and your AGP setting. Leave the HT(hyper-transport) set to 5X unless you plan on oc'ing, if you do oc then may find you'll need to reduce it to 4X or 3X. Try downloading the latest driver for your network from the MSI website. Right click the device in device manager and select update, select specific location then "don't look...I'll choose", direct it to the file where you've unpacked the correct driver and then update.

K8N Neo2 Platinum + Winchester 3200.. flabbergasting FSB issue

OK, here goes the issue:
I just got a brand new K8N Neo2 Platinum - Bios 1.4 and a box 3200 Winchester CPU. The crazy thing is the FSB - it is set to 200 Mhz in the Bios, but in real-time it happens to be something like 200.95 Mhz. No idea how to fix this - as a result the CPU goes at 2010 Mhz, while obiviously it should run at 2000Mhz. There are also some stability problems, like random hangups in Windows. My ram is 2x512 Kingston HyperX PC4000.
Thanks in advance for any suggestions.

Also about your "hang up" deal... Post more detailed specs on your system - You'll get better help that way.

My K8n neo2 wont overclock at all!! plz help...

Hi, I just build my new machine, and after much problems I finally have it up and running at stocks speeds just fine, the problem is that I spent a lot of money buying Top-Brand components so I could overclock a lot, (I like It) but I cant seem to go upweard of 205FSB!! anything above that and the board wont boot at all forcing me to clear the Cmos!! I find this completely unaceptable for this board, being that my last board (an Msi one with nforce2) could overclock and athlon XP 2500+ barton all the way up to a 2800+!! Im really dissapointed at this, if someone could give me a few pointers as to what tweak in the bios (Im using 1.3 right now) it will be very thankful!! ok, my specs are below, thanks!!
Athlon64 3500+ socket 939
Msi k8N Neo2 Platinum with 1.3bios
2+512mb Crucial Ballistix pc3200 cl2
BFG Nvidia Geforce 6800Gt
36gb Raptor Hdd
Enermax 420W power supply
Thanks!!!

I think your problem is your power supply. Check what that MAX amp on your 12V rail.
I have nearly the exact same setup as you do and was unable to overclock the memory without lowering the memory timings much earlier than I expected too. For me I'm able to raise my FSB up to 207 at 2-2-2 timings. The max overclock I achieved was 220 X11 at 2.5-3-3 for a speed of 2420mghz. But it was not completly stable (it would bout but would lock up while gamming). I had expected much better results than this... I bought good memory (Ballistix pc4000) I had a good 480W power supply... my processors ceilling should be around 2.6ghz. After reading this review on Anand Tech I think I found the answer... Athlon 64 Memory: Rewriting the Rules
On page 10 they make the remark that their Antec True Power 465W power suply was limiting their ability to overclock memory.... The Antec True Power is rated to supply 22A on the 12v rail. My power supply is only rated to supply 18A. I bet your 420W is rated even less.
After reading that I fiddled with async overclocking and was stable up to 230FSB... then my hard drive freaked out... I was using sata port 1. I moved the hard drive to SATA port 4, but haven't tried much overclocking since. Maybe if they put out a bios revision that I can adjust the HT on I'll try again. Until them I'm settled for running at 2277mghz.

Very serious issue with MSI K8N Neo2-FX: need urgent help!

Hi! I am facing the following problems:
1. 3D Mark 05 demo, COD2 single player and Half Life 2 become semi-frozen.
2. The audio loops, and audio & video go out of sync.
3.VPU Recover/Infinite loop issue DOES NOT kick in.
4. The semi frozen game responds poorly to mouse movement.
Note: All redundant processes and programs in Windows XP are closed. My system specs:
Athlon 64 3000+ E6
256 mb ddr333 kingston valueram + 256 mb ddr400 kingston valueram=512 mb ddr333 total memory running in dual channel mode @ 2.5-3-3-7 (RAM is OK, worked fine on my previous system)
MSI K8N Neo2-FX bios version 1.B0(latest) chipset: nforce 3 250gb http://www.msi.com.tw/program/produc...il.php?UID=649
gigabyte radeon 9600XT BIOS Part Number BK-ATI VER008.015.058.000 (Card stable at 1.6 V AGP, 1.5 V gave me VPU Recover; Card ran fine on my previous system)
Realtek ALC 850 onboard audio
Antec SL 450 450 watt PSU (new, voltages ok) latest drivers/bios/firmware for everything Windows XP Pro SP2 + all updates. Please help.

Quote from: Richard on 03-May-06, 08:40:18
bhanja_trinanjan,
If you can get 2.3.3.6 Mushkin, OCZ, or Corsair, then you would be the set.
PC-3200 or higher would be the way to go. If you ever plan on overclocking, then PC-4000 is the best option.
Take Care,
Richard
Thanks for your help. I am trying to locate Corsair dealers in Kolkata(My hometown). Are there any known issues with the K8N Neo 2 FX? I bought this motherboard just a few days back and I am facing so many problems.
Does this motherboard undervolt the AGP and RAM slots? Will I have to increase AGP and DDR voltage to make my system stable? Doesn't the raising of these voltages shorten the life of the video card and ram modules? I want to buy Corsair/OCZ/Mushkin. But in case it's unavailable, will Kingston RAM lead to an unstable system?

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

K8N Neo2 & Crucial PC3200 2 X 512 (Model: CT6464Z40B) help please!!!

Dear friends:
I just built my first AMD system, with some hesitation to be honest, and of now, the new system has a memory related problem. I have the following:
Crucial (512MB X 2) 1 GB PC3200 400Mhz CL3 DDR DIMM (Model:
CT6464Z40B)
When I tried to install WinXP Pro for the first time with the two memory modules installed, the system will freeze in the middle of the installation. When I removed the module from slot 3 (green in color) and leave the other in slot 1 (green), WinXP will load in a breeze. With WinXP loaded, I re-inserted the module in slot 3 and after a short while the system froze again. I removed it once more and the system runs as it should. I removed the module in slot 1 and replaced it with the one in slot 3, and ran the PC with just that one and the PC run just fine, I even installed SP2 and the system runs just fine with one memory module. My conclusion is that the MOBO doesn't what to run with both modules installed. I haven't flashed the BIOS yet, that will be my next step.
Could someone please help me set the DRAM configuration in the BIOS. I know someone out there already has the right settings for the brand and model mention above and running a stable system.
Also please help me decipher what the following means (as far as the sequence goes): 2.5-3-3-5-1T TrC11
or
2-3-2-5-1T 230Mhz ***** these are not the right ones******
Where do the above go when the sequence in the DRAM in the BIOS in the following:
Settings
Max Memclock (MHz) [100, 133, 166, 200]
1T/2T Memory Timing [1T/2T]
CAS# latency (Tcl) [2.0, 2.5, 3.0]
RAS# to CAS# delay (Trcd) [2,3,4,5,6,7]
Min Ras# active time (Tras) [5,6,7,8,9,10,11,12,13,14,15]
Row precharge Time (Trp) [2,3,4,5,6]
**All have an "auto" setting**
I apologize for the length of this post and my ignorance about this matter.
One more thing, I haven't installed the sound board until the system is stable.
Thanks in advance for all your help
Chinche

That's IT!! I've HAD it!! M_ther F_cker! M_ther F_cker! No MORE! Not Tonight!
I give up. I have messed with every single Memory timing and voltage setting. One stick of crucial memory works no matter what the settings are, and two sticks of crucial memory throw errors no matter what I do to the BIOS settings.
I took my memory to my friends house, who also has a K8N-Neo2 and it does the very same thing. There appears to be a problem with this mobo / ram combination.
I am going to contact MSI about it. For now, I am just using one stick of the Crucial memory just so I can have a stable system.
hansh, The reason you aren't having problems is because you are using Ballistix Crucial memory. chinche and I are using standard issue (read cheaper) Crucial memory. My friend is also using the Ballistix memory and his system is very stable and the memory even runs in Dual Channel mode! I'm going to see what MSI comes up with. If they can't help, I am going to RMA the cheap stuff and go for the Ballistix.
chinche, here is how to decipher the memory timings (at least according to memtest86+)
Tcl - Trcd - Trp - Tras - 1T/2T
They are slightly out of order with the K8N-Neo2 BIOS settings page.
3-3-3-8-2T means
1T/2T Memory Timing = 2T
CAS# latency (Tcl) = 3
RAS# to CAS# delay (Trcd) = 3
Min Ras# active time (Tras) =8
Row precharge Time (Trp) =3
Sometimes people will list @2.6V or @200Mhz also. This is either the Memory Voltage or the Memory Clock.
If you find the solution, please post it here. I will do the same.
-dillonth
system:
Cheiftec Dragon case
Powmax LP-6100EA 500W power supply with below outputs:
+3.3V@30A, +5V@50A, +12V@25A
MSI K8N Neo2 (model MS-7025)
AMD Athlon64 3000+ (retail CPU cooler)
2 x Crucial CT6464Z40B 512MB PC3200
eVGA e-GeForce 6800
SB Live X-gamer
1 x WD 60GB 7200rpm ATA HDD
2 x WD 200GB 7200rpm ATA HDD
3 x 80mm system coolers
Nothing is overclocked. BIOS settings are at Fail-Safe

K8N Neo2 Problems!! Please Help!

Hi there, another n00b here in this forum...
Just wanted some help with one of my K8N Neo2 mobos...
I have 4 of these mobos... 3 seem to work fine but the 4th one has given me major headaches...
I have tried 2 x 3200+ Winnies as well as 2 x 3500+ NewCastles & a 3500+ Winnie as well...
Ram used are 4 x 256MB XMS3500, 2 x 256Mb KHX3200 as well as 2 x 512MB XMS3500 (all BH5) as well as some generic ram on this mobo.
No matter what i do, I cannot get this mobo to boot up properly. The furthest I have gotten if to WinXP loading & then the $ucker freezes on me.
Trying different combos of CPU/RAM get's me nowhere. All I get is beeps if I try to run Dual Channel.
I have sent the board back for RMA & was told that there's nothing wrong with this board.
What to do now?? I'm at wits end because I expect a mobo capable of running dual channel to do so without any problems...
Maybe I should bring my setup to the shop/distributor & show them in front of their face for them to believe me??
Actually, the shop believes me, just that MSI's "quality" assurance can't seem to reproduce the errors I'm getting...
Maybe they should try to use 2 dimms instead of using 1 dimm & as soon as they get the machine to boot with the 1 dimm, they send it back to me saying that the board is faultless...
One unhappy MSI customer...

amen_pl
think we get the message it is the 4th time you've told us.
1) Wake on LAN/Keyboard wake for a K8N Neo Platinum - how do I use this?
2) Need help with WOL
3) K8N Neo-FSR: wake up on keyboard from S5 (soft-off state) missing?
this is a user forum no one from MSI is here. If you have an issue start a thread.

Overclocking my 3200+ Winchester on K8N Neo2.. Help!!!

Similar Messages

Maybe you are looking for